工艺条件对磷回收过程中鸟粪石沉淀颗粒粒径的影响

在鸟粪石沉淀法回收废水中磷的过程中,鸟粪石颗粒的大小将直接影响其沉淀的速率,进而影响鸟粪石的沉淀效果和磷的回收率。本文采用激光粒度分析仪测定鸟粪石的平均粒径,详细考察在小型连续搅拌反应-沉淀磷回收装置中不同的工艺条件下鸟粪石颗粒粒径的变化规律,并结合Stokes公式计算鸟粪石颗粒在废水出口处的沉降速率,为沉淀池的设计提供参考依据。结果表明:鸟粪石的平均粒径在12～25μm之间,沉降速率在5.46×10-5～2.37×10-4m/s之间。随着反应室水力停留时间的延长,鸟粪石颗粒的粒径逐渐增大,当停留时间超过18 min时,颗粒的粒径基本不变;随着沉淀室水力停留时间的延长,鸟粪石颗粒的平均粒径缓慢增大,当停留时间超过70 min后颗粒粒径的变化不大;鸟粪石颗粒的平均粒径在一定程度上受废水中磷初始浓度变化的影响,在磷初始浓度为62～128 mg/L时颗粒的粒径变化不大,当磷浓度为496 mg/L时粒径有较大增加,此时鸟粪石颗粒的沉降速率也大幅度增加;鸟粪石颗粒的平均粒径受pH值的影响不大;随氮磷摩尔比的增大,鸟粪石颗粒的平均粒径略有增加;随镁磷摩尔比的增大,鸟粪石颗粒的平均粒径逐渐减小,沉降速率则有明显的下降。     

黄磷工业污泥的处理技术探讨

黄磷生产及其废水处理工序中会产生含单质磷污泥 ,这是一种危险固体废物 ,会对周围环境造成长期污染。本文对黄磷生产中产生的不同类型的含单质磷污泥提出 3种不同处理工艺 ,并对这 3种工艺原理及在实践中使用情况做了分析 ,并做了相应的改进 ,为大型黄磷生产厂家处理含单质磷污泥提供了技术参考。     

Effects of reduced return activated sludge flows and volume on anaerobic zone performance for a septic wastewater biological phosphorus removal system.

Enhanced biological phosphorous removal (EBPR) performance was found to be adequate with reduced return-activated sludge (RAS) flows (50% of available RAS) to the anaerobic tank and smaller-than-typical anaerobic zone volume (1.08 hours hydraulic retention time [HRT]). Three identical parallel biological nutrient removal pilot plants were fed with strong, highly fermented (160 mg/L volatile fatty acids [VFAs]), domestic and industrial wastewater from a full-scale wastewater treatment facility. The pilot plants were operated at 100, 50, 40, and 25% RAS (percent of available RAS) flows to the anaerobic tank, with the remaining RAS to the anoxic tank. In addition, varying anaerobic HRT (1.08 and 1.5 hours) and increased hydraulic loading (35% increase) were examined. The study was divided into four phases, and the effect of these process variations on EBPR were studied by having one different variable between two identical systems. The most significant conclusion was that returning part of the RAS to the anaerobic zone did not decrease EBPR performance; instead, it changed the location of phosphorous release and uptake. Bringing less RAS to the anaerobic and more to the anoxic tank decreased anaerobic phosphorus release and increased anoxic phosphorus release (or decreased anoxic phosphorus uptake). Equally important is that, with VFA-rich influent wastewater, excessive anaerobic volume was shown to hurt overall phosphorus removal, even when it resulted in increased anaerobic phosphorus release.     

Hybrid process for heavy metal removal from wastewater sludge.

Bioleaching processes have been demonstrated to be effective technologies in removing heavy metals from wastewater sludge, but long hydraulic retention times are typically required to operate these bioprocesses. A hybrid process (coupling biological and chemical processes) has been explored in laboratory pilot-scale experiments for heavy metals (cadmium [Cd], copper [Cu], chromium [Cr], and zinc [Zn]) removal from three types of sludge (primary sludge, secondary activated sludge, and a mixture of primary and secondary sludge). The hybrid process consisted of producing a concentrate ferric ion solution followed by chemical treatment of sludges. Ferric iron solution was produced biologically via oxidation of ferrous iron by A. ferrooxidans in a continuous-flow stirred tank (5.2 L) reactor (CSTR). Wastewater sludge filtrate (WSF) containing nutrients (phosphorus and nitrogen) has been used as culture media to support the growth and activity of indigenous iron-oxidizing bacteria. Results showed that total organic carbon (TOC) concentrations of the culture media in excess of 235 mg/L were found to be inhibitory to bacterial growth. The oxidation rate increased as ferrous iron concentrations ranged from 10 to 40 g Fe2+/L. The percentage of ferrous iron (Fe2+) oxidized to ferric iron (Fe3+) increased as the hydraulic retention time (HRT) increased from 12 to 48 h. Successful and complete Fe2+ oxidation was recorded at a HRT of 48 h using 10 g Fe2+/L. Subsequently, ferric ion solution produced by A. ferrooxidans in sludge filtrate was used to solubilize heavy metals contained in wastewater sludge. The best solubilization was obtained with a mixture of primary and secondary sludge, demonstrating a removal efficiency of 63, 71, 49, and 80% for Cd, Cu, Cr, and Zn, respectively.     

曝气量和曝气时长对好氧颗粒污泥活性恢复的影响

采用啤酒废水,在SBR中对在4℃的冰箱中储存8周的好氧颗粒污泥进行活性恢复。设置曝气时长分别为150 min和270 min,曝气量分别为0.1 m3/h和0.2 m3/h,考察了曝气时长和曝气量对好氧颗粒污泥活性恢复的影响。实验结果表明,好氧颗粒污泥在4℃冰箱中储存8周后,其颜色、粒径无明显变化;设置较长曝气时间(270 min)、较大曝气量(0.2 m3/h)时,颗粒污泥平均沉降速率、MLSS和SVI恢复最快,且对COD处理效果也恢复较快。而短曝气时间(150 min)、小曝气量(0.1 m3/h)有利于好氧颗粒污泥对氨氮去除效果的恢复。     

一维分层弥散模型在二沉池模拟中的应用

通过在二沉池一维分层模型中加入弥散作用建立了二沉池一维分层弥散模型,并采用数值求解的方法开发了二沉池模拟程序.利用竖流式沉淀池中试试验实测数据验证了模型的可靠性,以COST(欧洲科技领域研究合作组织)624/682文件中基准污水处理厂二沉池晴天时的稳态和动态进水数据为模型输入值,分析比较了一维分层弥散模型模拟程序与国外成熟软件的模拟结果.结果表明,纳入了弥散作用的一维分层模型能较好地描述实际二沉池中的悬浮固体浓度分布,模拟结果具有较好的精度,有待于在二沉池模拟和控制领域进一步深入研究.     

Optimization of enhanced biological phosphorus removal after periods of low loading.

Enhanced biological phosphorus removal is a well-established technology for the treatment of municipal wastewater. However, increased effluent phosphorus concentrations have been reported after periods (days) of low organic loading. The purpose of this study was to evaluate different operating strategies to prevent discharge of effluent after such low-loading periods. Mechanisms leading to these operational problems have been related to the reduction of polyphosphate-accumulating organisms (PAOs) and their storage compounds (polyhydroxy alkanoates [PHA]). Increased effluent phosphorus concentrations can be the result of an imbalance between influent loading and PAOs in the system and an imbalance between phosphorus release and uptake rates. The following operating conditions were tested in their ability to prevent a reduction of PHA and of overall biomass during low organic loading conditions: (a) unchanged operation, (b) reduced aeration time, (c) reduced sludge wastage, and (d) combination of reduced aeration time and reduced sludge wastage. Experiments were performed in a laboratory-scale anaerobic-aerobic sequencing batch reactor, using acetate as the carbon source. Without operational adjustments, phosphorus-release rates decreased during low-loading periods but recovered rapidly. Phosphorus-uptake rates also decreased, and the recovery typically required several days to increase to normal levels. The combination of reduced aeration time and reduced sludge wastage allowed the maintenance of constant levels of both PHA and overall biomass. A mathematical model was used to explain the influence of the tested operating conditions on PAO and PHA concentrations. While experimental results were in general agreement with model predictions, the kinetic expression for phosphorus uptake deviated significantly for the first 24 hours after low-loading conditions. Mechanisms leading to these deviations need to be further investigated.     

响应面分析法优化造纸污泥吸附剂除磷工艺

以造纸厂废水污泥为原料,采用微波加热法制备造纸污泥吸附剂。利用制备的造纸污泥吸附剂对模拟含磷废水进行了吸附研究,探讨了吸附时间、投加量、pH值、转速和温度等因素对除磷效果的影响,并采用响应面设计法优化吸附工艺条件。结果表明,获得了最佳除磷工艺条件为吸附时间97 min,投加量6.9 g/L,pH=6,转速200 r/min,温度30℃,在此条件下磷的去除率可达99%以上。因此,造纸污泥吸附剂对磷的吸附效果良好,具有重要的实际应用价值。     

矿化垃圾生物反应床处理印染废水的工艺参数优化及优势菌群

为了探讨矿化垃圾再利用于印染废水处理的可行性,研究了矿化垃圾生化反应床处理模拟印染废水的工艺参数,进行了优势菌群的镜检和提取、培养,实验结果表明,适宜的工艺运行参数如下为水力停留时间12~24 h,水力负荷100~140 L/(m3·d),COD污染负荷240~360 g/(m3·d),布水周期为24 h条件下的进水历时为6 h;适宜的工艺运行参数条件下,矿化垃圾生化反应床对模拟印染废水的COD去除率97%以上,总磷去除率95%以上,氨氮的去除率在98%以上;处理模拟印染废水的矿化垃圾生化反应床内的微生物群落以球菌为主,该菌体对模拟印染废水具有良好的专性降解作用。研究结果将对矿化垃圾的再利用和印染废水的处理提供一定的技术参考。     

Gamma irradiation of municipal sludge for safe disposal and agricultural use.

Gamma radiation was found to be an effective tool for hygienization of municipal wastewater sludge. The sludge received from the primary settling tank of a municipal wastewater treatment plant was gamma irradiated using a cobalt-60 source in a sludge hygienization research irradiator. The process parameters were adjusted to effectively eliminate coliform bacteria in the sludge and to prevent their regrowth. Irradiated sludge was found to be free of fecal coliform and could be directly disposed after drying in a landfill or used as manure. It could also be used as a medium for growth of Rhizobium sp for obtaining a bio-fertilizer.     

实际污水与模拟污水活性污泥系统的特性差异

实验中经常采用人工配置的模拟生活污水,为了研究其与实际生活污水活性污泥系统的特性差异,采用2个序批式间歇反应器(SBR)进行平行实验(厌氧、好氧方式运行),系统地考察了在进水主要组分和运行参数相同的情况下,不同原水对活性污泥系统脱氮、除磷、比好氧速率、污泥絮体形态和出水水质等方面的影响。结果表明,模拟污水系统的硝化活性强于实际污水系统,两者的平均硝化速率分别为7.43 mg NH4+-N/(L.h)和5.55 mg NH4+-N/(L.h)。在前置厌氧段,模拟污水系统的释磷量比实际污水系统高出36.45%。两者在后续好氧阶段都能够充分吸磷。模拟污水系统的平均比好氧速率(SOUR)高达64.54 mg O2/(g MLSS.h),而实际污水系统的则只有32.81 mg O2/(g MLSS.h)。模拟污水系统的污泥絮体疏松,粒径小,形状不规则,沉降性差,沉后出水平均悬浮物浓度(SS)为20 mg/L;而实际污水系统的污泥絮体则密实、粒径大,沉降性好,沉后水十分清澈,SS几乎检测不出。     

PACT工艺处理PAM生产废水的实验研究

采用粉末活性炭活性污泥工艺(PACT)处理经凹凸棒土预处理后的聚丙烯酰胺(PAM)生产废水。实验考察了粉末活性炭(PAC)的投加对活性污泥处理系统的影响,并探讨了PAC投加量、曝气时间、水力停留时间等参数对降解反应的影响。结果表明:PAC的投加能提高水中溶解氧的利用率,改善污泥沉降性能,增强活性污泥系统对有机物的去除效果;在PAC投加量500 mg/L、曝气10 h的条件下,PACT工艺对PAM生产废水的处理效果良好,COD的去除率为80.8%,BOD5去除率为83.8%,丙烯酰胺(AM)去除率为84.2%。     

不同电子受体对聚磷菌吸磷性能的影响研究

采用人工配水,在厌氧/好氧交替运行的序批式活性污泥反应器(SBR)中,富集了全菌数量80%以上的聚磷菌(Candi-datus Accumulibacter Phosphates)。以此为基础,研究了O2及不同浓度NO3--N、NO2--N对聚磷菌吸磷的影响。结果表明,在一定的条件下,聚磷菌可以NO3--N和NO2--N为电子受体进行缺氧吸磷;NO3--N浓度对聚磷菌的吸磷速率影响很小;聚磷菌可以低质量浓度NO2--N(≤40mg/L)为电子受体,但不能以高质量浓度NO2--N(≥80mg/L)为电子受体,而且高浓度NO2--N对聚磷菌吸磷产生抑制甚至对细菌本身存在毒害;NO2--N为电子受体时,其抑制浓度和污泥本身以及外界条件都存在很大的关系,各个研究结论不尽相同,其影响过程有待进一步的探讨。     

分点进水A/O工艺处理低碳源生活污水的脱氮性能研究

针对低C/N比污水脱氮的难点问题,在缺氧段不同点设置进水口,采用分点进水A/O工艺处理校园生活污水.考察了在污泥回流比为100%,硝化液回流比为200%,分流比为1∶1,缺氧池水力停留时间(HRT)分别为2、2.4和3 h情况下,分点进水A/O工艺的反硝化性能,并与传统的A/O工艺进行比较.结果表明,当缺氧池的水力停留...     

耦合回流污泥预浓缩系统的新型氧化沟工艺强化除磷

针对传统的"厌氧+氧化沟"运行模式对低碳源污水除磷能力不佳的问题,采用耦合回流污泥预浓缩系统的新型氧化沟工艺对其强化除磷进行了中试实验研究。通过采用回流污泥预浓缩系统,调试回流污泥浓缩比,提高系统的除磷能力。研究结果表明,在控制最佳回流污泥浓缩比为55%的情况下,出水TP浓度和去除率分别为0.92 mg/L和67.5%,相比于浓缩比为100%、70%、50%和30%的工况,其去除率分别增加了24.3%、27.3%、8.2%和28.6%,强化了系统的除磷效果。另外,ORP可以预示预缺氧池内无效释磷和反硝化程度,以此作为自动调整最佳回流污泥浓缩比的控制参数。     

Image analysis application for the study of activated sludge floc size during the treatment of synthetic and real fishery wastewaters

Background, aim, and scope  

Fishery wastewater treatment can be compromised due to seasonal production. The use of sequencing batch reactors is not completely successful, despite flexibility being one of the principal advantages. Most research on activated sludge is performed using synthetic wastewater to ensure a stable and constant feed. The current work compared biomass morphology and settling ability using image analysis of synthetic and real fishery wastewaters, with and without NaCl addition.     

Fractionation and mobility of phosphorus in a sandy forest soil amended with biosolids

Goal, Scope and Background Biosolids, i.e., treated sewage sludge, are commonly used as a fertilizer and amendment to improve soil productivity. Application of biosolids to meet the nitrogen (N) requirements of crops can lead to accumulation of phosphorus (P) in soils, which may result in P loss to water bodies. Since 1996, biosolids have been applied to a Pinus radiata D. Don plantation near Nelson City, New Zealand, in an N-deficient sandy soil. To investigate sustainability of the biosolids application programme, a long-term research trial was established in 1997, and biosolids were applied every three years, at three application rates, including control (no biosolids), standard and high treatments, based on total N loading. The objective of this study was to evaluate the effect of repeated application of biosolids on P mobility in the sandy soil. Materials and Methods Soil samples were collected in August 2004 from the trial site at depths of 0–10, 10–25, 25–50, 50–75, and 75–100 cm. The soil samples were analysed for total P (TP), plant-available P (Olsen P and Mehlich 3 P), and various P fractions (water-soluble, bioavailable, Fe and Al-bound, Ca-bound, and residual) using a sequential P fractionation procedure. Results and Discussion Soil TP and Olsen P in the high biosolids treatment (equivalent to 600 kg N ha⁻¹ applied every three years) had increased significantly (P<0.05) in both 0–10 cm and 10–25 cm layers. Mehlich 3 P in soil of the high treatment had increased significantly only at 0–10 cm. Olsen P appeared to be more sensitive than Mehlich 3 P as an indicator of P movement in a soil profile. Phosphorus fractionation revealed that inorganic P (Al/Fe-bound P and Ca-bound P) and residual P were the main P pools in soil, whereas water-soluble P accounted for approximately 70% of TP in biosolids. Little organic P was found in either the soil or biosolids. Concentrations of water-soluble P, bioavailable inorganic P (NaHCO₃ Pi) and potentially bioavailable inorganic P (NaOH Pi) in both 0–10 and 10–25 cm depths were significantly higher in the high biosolids treatment than in the control. Mass balance calculation indicated that most P applied with biosolids was retained by the top soil (0–25 cm). The standard biosolids treatment (equivalent to 300 kg N ha⁻¹ applied every three years) had no significant effect on concentrations of TP, Mehlich 3 P and Olsen P, and P fractions in soil. Conclusions The results indicate that the soil had the capacity to retain most biosolids-derived P, and there was a minimal risk of P losses via leaching in the medium term in the sandy forest soil because of the repeated biosolids application, particularly at the standard rate. Recommendations and Perspectives Application to low-fertility forest land can be used as an environmentally friendly option for biosolids management. When biosolids are applied at a rate to meet the N requirement of the tree crop, it can take a very long time before the forest soil is saturated with P. However, when a biosolids product contains high concentrations of P and is applied at a high rate, the forest ecosystem may not have the capacity to retain all P applied with biosolids in the long term. ESS-Submission Editor: Dr. Jean-Paul Schwitzguébel jean-paul.schwitzguebel@epfl.ch     

Correlation analysis of major control factors for the formation and stabilization of aerobic granule

In recent years, aerobic granular sludge technology has demonstrated significant advantages in areas such as the sludge–water separation, residual sludge minimization, simultaneous biological nitrogen and phosphorus removal, and toxic organic compounds degradation in biological wastewater treatment. However, the critical control factors and their relation during sludge granulation have not been revealed indeed, and the stability of aerobic granular sludge is still not good. The Gray’s correlation analysis was used to investigate the relationship of aerobic granular characteristics and control factors in the study. Results showed that the organic loading rate, hydraulic shear stress, and sludge settling time were the major factors affecting the aerobic sludge granulation, and the associated regulating strategy was important for the stabilization of granular sludge system. Based on above results, the mechanism of aerobic sludge granulation was proposed, and it was expected to favor the application of aerobic granular sludge technology.     

A practical method for quantification of phosphorus- and glycogen-accumulating organism populations in activated sludge systems.

Enhanced biological phosphorus removal (EBPR) from wastewater relies on the enrichment of activated sludge with phosphorus-accumulating organisms (PAOs). The presence and proliferation of glycogen-accumulating organisms (GAOs), which compete for substrate with PAOs, may be detrimental for EBPR systems, leading to deterioration and, in extreme cases, failure of the process. Therefore, from both process evaluation and modeling perspectives, the estimation of PAO and GAO populations in activated sludge systems is a relevant issue. A simple method for the quantification of PAO and GAO population fractions in activated sludge systems is presented in this paper. To develop such a method, the activity observed in anaerobic batch tests executed with different PAO/GAO ratios, by mixing highly enriched PAO and GAO cultures, was studied. Strong correlations between PAO/GAO population ratios and biomass activity were observed (R2 > 0.97). This served as a basis for the proposal of a simple and practical method to quantify the PAO and GAO populations in activated sludge systems, based on commonly measured and reliable analytical parameters (i.e., mixed liquor suspended solids, acetate, and orthophosphate) without requiring molecular techniques. This method relies on the estimation of the total active biomass population under anaerobic conditions (PAO plus GAO populations), by measuring the maximum acetate uptake rate in the presence of excess acetate. Later, the PAO and GAO populations present in the activated sludge system can be estimated, by taking into account the PAO/GAO ratio calculated on the basis of the anaerobic phosphorus release-to-acetate consumed ratio. The proposed method was evaluated using activated sludge from municipal wastewater treatment plants. The results from the quantification performed following the proposed method were compared with direct population estimations carried out with fluorescence in situ hybridization analysis (determining Candidatus Accumulibacter Phosphatis as PAO and Candidatus Competibacter Phosphatis as GAO). The method showed to be potentially suitable to estimate the PAO and GAO populations regarding the total PAO-GAO biomass. It could be used, not only to evaluate the performance of EBPR systems, but also in the calibration of potential activated sludge mathematical models, regarding the PAO-GAO coexistence.     

蜂窝陶瓷载体生物膜技术处理农药废水

以蜂窝陶瓷为载体进行生物挂膜,处理经化学预处理后的某农药厂有机磷和除虫菊酯类混合废水。对处理结果、蜂窝陶瓷载体及其生物挂膜法的特点进行了深入讨论。当废水的COD为1 600～1 700 mg/L,TP(总磷)为70～80mg/L,DMAC(二甲基乙酰胺)为0.8～1.2 mg/L,甲醇为8～12 mg/L,pH为6.8～7.2,水温为27～30℃,流量为0.1 m3/h,水力停留时间为15 h,进水容积负荷约为2.5 kg COD/(m3.d)时,发现15 d就完成生物挂膜,连续运行20 d COD去除率为73%～75%,TP去除率为53%～55%,DMAC去除率为54%～57%,甲醇去除率为91%～93%。与同样条件下的普通活性污泥处理相比,COD去除率提高85%,TP去除率提高83%,DMAC去除率提高119%,甲醇去除率提高27%,排出的剩余活性污泥量减少89%。测得的活性生物膜量为1.8 kg/m2,生物膜的厚度为1.5～2 mm,用偏光显微镜摄取了载体表面生物膜的图像。