不同水力停留时间条件下PCL为碳源去除水产养殖水体硝酸盐的效率及微生物群落分析

以可生物降解聚合为碳源的固相反硝化可以避免水产养殖用水硝酸盐处理过程中碳源反复添加、碳源不足或过量等问题。水力停留时间(hydraulic retention time,HRT)是生物反应器运行管理的主要参数之一,用固定膜反应器固相反硝化的方法研究了HRT对以聚己内酯(polycaprolactone,PCL)为碳源的反应器去除循环水养殖系统硝酸氮(浓度为170~197 mg·L~(-1))的效率的影响。研究结果表明不同水力停留时间对硝酸盐去除效率差异显著。在HRT为6 h和8 h时,硝酸盐速率分别为(0.55±0.32)g·(L·d)~(-1)和(1.05±0.33)g·(L·d)~(-1),且出水亚硝氮浓度和氨氮浓度均明显低于进水浓度;在HRT为4 h和2 h时,进出水硝酸盐浓度差异不明显。电子扫描显微镜观察显示PCL表面生物膜主要为杆状菌,应用傅里叶红外扫描观察发现使用前后PCL的化学结构没有发生明显改变。应用高通量方法测定的微生物群落结构表明,62%的细菌为Proteobacteria(62%),在鉴定出的细菌中,食酸菌属(Acidovorax),固氮螺菌属(Azospira),丛毛单胞菌属(Comamonas),代尔夫特菌属(Diaphorobacter),懒小杆属(Ignavibacterium),弗拉特氏菌属(Frateuria)可以同时降解PCL和进行反硝化。     

厌氧/特异性移动床生物膜反应器处理低碳氮比工业废水脱氮效果优化分析

采用SDC-03型填料作为生物载体,对厌氧/特异性移动床生物膜反应器(A/SMBBR)工艺处理低碳氮比工业废水的挂膜启动及稳定运行过程进行优化分析。通过单因素试验和基于Box-Behnken设计的响应曲面法考察了碳源投加量(以乙醇为碳源)、水力停留时间(HRT)及填料填充率对系统TN去除率的影响及其交互作用。结果表明:(1)3个参数对TN去除率影响顺序为填料填充率碳源投加量HRT,其中填料填充率和HRT之间的交互作用最显著。(2)模型预测的最佳条件为碳源投加量90mg/L、HRT=3.0d、填料填充率55%,TN去除率预测值为90.78%。在该条件下TN去除率实际值达91.02%,与模型预测值基本一致,表明响应曲面模型与实际情况拟合良好。     

基于化学与生物膜耦合深度脱除地下水中硝酸盐氮

我国华北地区超过80%的地下水受到污染,其中硝酸盐氮的污染日益严重,威胁着人类健康。基于单质铁去除地下水中硝酸盐氮,因伴随氨氮的产生而受限制;生物反硝化脱氮因地下水中碳源不足无法满足脱氮要求。采用自制的微电解化学催化固体颗粒与天然生物质构成耦合生物载体,通过自养与异养反硝化耦合深度脱除地下水中硝酸盐氮,并建立了地下水易位好氧、厌氧深度脱氮新工艺。结果表明:好氧反应器在HRT为12 h、DO为2.0～3.0 mg·L-1的条件下,硝酸盐氮平均去除率≥91.24%;厌氧反应器在HRT为14 h的条件下,硝酸盐氮平均去除率≥96.32%;反应器中微电解化学催化固体颗粒可为自养反硝化菌提供电子,生物质可为微生物提供必要的有限碳源,硝酸盐氮的脱除是自制微电解化学催化固体颗粒与生物膜耦合作用的结果。出水均无亚硝酸盐氮和氨氮积累。此技术可为受污染地下水的修复提供理论依据。     

电极改性对电极生物膜反硝化反应器硝酸盐氮去除性能的影响

探究在碳纤维毡电极上利用恒电压电化学聚合聚吡咯(PPy)的聚合效果,并利用傅里叶变换红外线(FTIR)及扫描电镜(SEM)对其进行表征;将聚吡咯覆膜改性后的碳纤维毡电极应用到自养反硝化的电极生物膜反应器(BER)中,考察电极改性对自养反硝化电极生物膜反应器的硝酸盐氮去除性能影响,并研究电极改性对生物膜附着量及生物膜微生物群落的影响。结果表明,恒电压电化学聚合能够在碳纤维电极表面形成均匀稳定的聚吡咯膜,从而实现聚吡咯在炭纤维毡电极上的覆膜改性。改性后的电极应用到自养反硝化电极生物膜反应器中,可使反应器对NO_3~--N的去除效率由对照反应器的67.3%增加到83.9%,处理效果提高了24.7%。对反应器内电极生物膜进行生物量测定和扫描电镜分析,可以看到R2反应器中改性电极生物膜附着量明显多于R1反应器中未改性电极生物膜的附着量,说明电极改性有利于生物膜的附着。电极生物膜微生物16S rDNA分析中R1反应器电极生物膜菌落组成中优势菌属为Dechloromonas sp.,而R2反应器电极生物膜的优势菌为Hydrogenophaga sp.(噬氢菌属)和Thauera sp.(陶厄氏菌属),两者有明显差别,并且R2反应器比R1反应器生物膜的菌落组成更多样化,这说明电极材料的改性对电极生物膜微生物群落的组成产生了影响。     

MBBR一体式耦合短程硝化-厌氧氨氧化处理污泥水

采用移动床生物膜反应器(MBBR)处理已回收磷后的实际污泥水,在进水平均氨氮浓度为167.51 mg·L~(-1)、HRT为22.24 h、DO为0.5 mg·L~(-1)和温度为24～26℃的条件下实现了一体式短程硝化-厌氧氨氧化过程的耦合,对氨氮和总无机氮的最大去除率可达96%和79.7%。但是,一体式反应器受DO浓度影响较大,维持稳定的DO浓度对于系统的氮去除非常重要。荧光原位杂交(FISH)及高通量测序结果表明,MBBR的生物膜及活性污泥中Nitrosomonas菌分别占总菌数的10.46%和21.46%,厌氧氨氧化菌的优势菌种Candidatus Kuenenia在生物膜和活性污泥中分别占总菌数的4.13%和0.71%。因此,MBBR中活性污泥主要完成亚硝化,生物膜主要完成厌氧氨氧化,常温条件下,两者在一个反应体系中共同完成了对污泥水中氮的高效自养脱除。以上结果表明了一体式反应器处理实际污泥水的可行性,可为该工艺在实际工程中的应用提供参考。     

外循环生物流化床挂膜启动研究

自行设计了一台小型外循环生物流化床,并研究了该流化床处理垃圾渗滤液启动过程中,载体填充率、曝气量、水力停留时间(HRT)和进水碳、氮质量比(C/N)对椰壳活性炭载体表面生物膜形成的影响。结果表明,挂膜启动过程中较合适的条件为载体填充率5%(体积分数)、曝气量80L/h、HRT 8h、进水C/N 8~10。     

PCL-SND系统的脱氮效果

以处理水产养殖水体中的含氮化合物为目的,采用气提反应器,建立以聚己内酯(polycaprolactone,PCL)为碳源和生物膜载体的同时硝化反硝化(simultaneous nitrification and denitrification,SND)系统(PCL-SND),研究其启动过程及脱氮效果以及水力停留时间(hydraulic retention time,HRT)对PCL-SND系统脱氮效果的影响。结果表明,在PCL填充率为10%,HRT为24 h,进水氨氮(NH+4-N)浓度为10 mg/L,硝态氮(NO-3-N)浓度为50 mg/L的条件下,系统运行45 d达到稳定状态,NH+4-N和TN的去除率分别为(76.55±0.98)%和(56.85±2.21)%。HRT对PCL-SND系统脱氮效果的研究表明,一定范围内,TN去除率随着HRT的减小而下降,出水NO-3-N浓度随着HRT的减小而升高,当HRT8 h,NH+4-N去除率基本稳定(85%~89%),HRT为24 h时,脱氮效果最好,TN和NH+4-N去除率分别为(68.56±1.64)%和(87.75±2.78)%,出水NO-3-N浓度(15.72±1.46)mg/L。p H和总碱度均随HRT的减小而下降,生物量却随HRT的减小而增大。     

悬浮填料生物膜反应器细菌群落季相更替对处理效果的稳定作用

针对生物实验室污水处理难度高及其秋冬季节达标率低的问题,采用改进工艺的悬浮填料生物膜反应器(moving bed biofilm reactor, MBBR)进行连续处理,观察秋冬季节MBBR水质处理效果,利用高通量测序技术研究环境因子水温(T_w)、溶解氧(DO)、pH对生物膜细菌群落更替的影响以及主要微生物种群变化。结果表明,T_w由26℃下降到10℃期间,反应器COD、NH_4~+-N去除率仍然分别保持在75%、80%左右,MBBR出水稳定在一级A标准。变形菌门(Proteobacteria)、拟杆菌门(Bacteroidetes)和浮霉菌门(Planctomycetes)是生物膜主要优势菌门,T_w的下降引起拟杆菌门的相对丰度显著升高。假单胞菌属(Pseudomonas)和黄杆菌属(Flavobacterium)在低T_w下成为优势菌属,动胶菌属(Zoogloea)相对丰度保持稳定。通过冗余分析(RDA)发现,DO与短波单胞菌属(Brevundimonas)、pH与脱氯单胞菌(Dechloromonas)、固氮弧菌属(Azoarcus)具有显著正相关性,T_w与假单胞菌属、黄杆菌属具有显著负相关性。MBBR结果揭示,细菌群落动态更替是MBBR出水水质仍然保持稳定的重要原因。     

不同填充率对移动床生物膜反应器的产泥性能影响研究

研究了不同填充率下（10%～70%）移动床生物膜反应器的生物膜特征和处理效果,以及填充率与污泥产率的关系。结果表明：随着填充率的增加,填料上生物膜厚度逐渐减少,反应器中附着微生物浓度逐渐增加;污泥产率因填充率不同而有很大差异,同一个反应器内污泥产率随填充率的增加而减少;在进水COD为400 mg/L、NH⁺₄-N为40 mg/L、水力停留时间为12 h条件下,不同填充率下COD去除率均可达到94%以上,NH⁺₄-N去除率达到97%以上。     

一株反硝化细菌的分离鉴定及其反硝化特性

从处理城镇污水的移动床生物膜反应器中分离获得一株反硝化细菌D3,并进一步研究该菌株的系统发育地位及反硝化特性。采用16S rDNA序列分析对菌株进行初步鉴定,探讨了基质浓度、起始pH和温度对菌株反硝化活性的影响。根据形态学特征、生理生化特性及16S rDNA序列测定分析,初步鉴定菌株属于寡养单胞菌属。该菌能利用硝酸钠或亚硝酸钠进行反硝化作用,最佳电子受体是硝酸盐氮,反硝化速率最大为19.86 mg/(L·h),最适生长pH为7.36,最适生长温度为33.5℃。菌株D3在初始硝态氮浓度为140 mg/L,以乙酸钠为惟一碳源,pH为7.36,温度33.5℃的最优生长条件下,培养10 h进入对数生长期,倍增时间为9.9 h,48 h内硝酸盐还原率达95%。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.