焙烧温度对催化剂Cu-Ni-Ce/SiO2性能的影响

采用浸渍法在不同焙烧温度下制备了用于湿式H202降解吡虫啉农药废水的Cu-Ni-Ce/SiO2催化剂,利用TG、BET、XRD和XPS等对其进行了表征,研究了焙烧温度对催化剂表面结构的影响以及催化剂表面结构与活性及稳定性之间的关系.结果表明:降低焙烧温度,cu、Ni、ce之间的相互作用使得催化剂晶粒尺寸减小,比表面积增加,Cu、Ni固溶体量和催化剂表面化学吸附氧量增加.湿式H,O,降解吡虫啉农药废水时,600℃下焙烧获得的Cu-Ni-Ce/Si02催化剂活性最高;在催化剂用量10 g·L-1、反应温度为110℃、双氧水用量为理论需用量、进水pH为9.0、反应时间为60 min的条件下,COD去除率为91.5%,活性组分溶出量较小.研究结果表明,焙烧温度对CuO、NiO、CeO,及Cu、Ni固溶体之间的相瓦作用有较大影响,从而影响了催化剂湿式降解吡虫啉农药废水的活性和稳定性.     

Unraveling SO2-tolerant mechanism over Fe2（SO4）3/TiO2 catalysts for NOx reduction

Developing low-temperature SO₂-tolerant catalysts for the selective catalytic reduction of NO_x is still a challenging task. The sulfation of active metal oxides and deposition of ammonium bisulfate deactivate catalysts, due to the difficult decomposition of the as-formed sulfate species at low temperatures（<300 °C）. In recent years, metal sulfate catalysts have attracted increasing attention owing to their good catalytic activity and strong SO₂ tolerance at hi...     

焙烧温度对Fe2O3/SAPO-34催化剂低温NH3选择性催化还原NO性能的影响

采用尿素沉淀法制备了一系列Fe_2O_3/SAPO-34催化剂,考察了催化剂焙烧温度(200、300、400、500℃)对低温NH_3选择性催化还原(NH_3-SCR)NO性能的影响,并利用X射线衍射(XRD)、N_2吸附-脱附、原子吸收光谱(AAS)、场发射扫描电镜(FE-SEM)、X射线光电子能谱(XPS)、H_2程序升温还原(H_2-TPR)、NH_3程序升温脱附(NH_3-TPD)等多种手段对催化剂的表面结构和物理化学性质进行表征分析.XRD和FE-SEM分析表明,在较低的焙烧温度(400℃)下,铁物种能够高度均匀地负载在SAPO-34表面上.NH_3-TPD和H_2-TPR分析表明,高分散状态的Fe_2O_3使催化剂暴露出更多的强酸位和活性位,有利于提高催化剂的NH_3吸附和活化能力及氧化还原性能,从而使催化剂呈现出更高的低温SCR活性.BET和XPS分析表明,在较低的焙烧温度下,Fe_2O_3/SAPO-34催化剂具有更大的比表面积和更高的化学吸附氧比例,促进NO氧化为中间产物NO_2,从而加快低温SCR反应的进行.活性测试结果表明,300℃焙烧的Fe_2O_3/SAPO-34催化剂具有最佳的低温活性和较强的抗硫抗水性能,在空速为40000 h~(-1)的条件下,且反应温度为190~240℃时,NO转化率达90%以上且N_2选择性接近100%.     

Iron-doped Mn-Ce/TiO2 catalyst for low temperature selective catalytic reduction of NO with NH3

The catalysts of iron-doped Mn-Ce/TiO 2(Fe-Mn-Ce/TiO 2) prepared by sol-gel method were investigated for low temperature selective catalytic reduction(SCR) of NO with NH 3.It was found that the NO conversion over Fe-Mn-Ce/TiO 2 was obviously improved after iron doping compared with that over Mn-Ce/TiO 2.Fe-Mn-Ce/TiO 2 with the molar ratio of Fe/Ti = 0.1 exhibited the highest activity.The results showed that 96.8% NO conversion was obtained over Fe(0.1)-Mn-Ce/TiO 2 at 180°C at a space velocity of 50,000 hr 1.Fe-Mn-Ce/TiO 2 exhibited much higher resistance to H 2 O and SO 2 than that of Mn-Ce/TiO 2.The properties of the catalysts were characterized using X-ray diffraction(XRD),N 2 adsorption,temperature programmed desorption(NH 3-TPD and NOx-TPD),and Xray photoelectron spectroscopy(XPS) techniques.BET,NH3-TPD and NOx-TPD results showed that the specific surface area and NH3 and NOx adsorption capacity of the catalysts increased with iron doping.It was known from XPS analysis that iron valence state on the surface of the catalysts were in Fe3+ state.The doping of iron enhanced the dispersion and oxidation state of Mn and Ce on the surface of the catalysts.The oxygen concentrations on the surface of the catalysts were found to increase after iron doping.Fe-Mn-Ce/TiO2 represented a promising catalyst for low temperature SCR of NO with NH3 in the presence of H2 O and SO2.     

Ce改性Mn系催化剂结构及低温催化活性影响研究

采用浸渍法制备了Ce改性负载型Mn系TiO 2催化剂,考察了Ce负载量、反应温度等因素对催化剂效率以及选择性的影响,利用扫描电镜、氮气物理吸附(N 2-TPD)等表征手段分析了Ce/TiO 2催化剂催化活性影响机理。结果表明:改性催化剂在Ce/Ti摩尔比为0.08的条件下表现出最佳的脱硝效率及NO选择性;MnCe(0.08)Ti催化剂在180℃条件下的脱硝效率超过85%,而N 2 O体积分数仅为24×10-6(47.1 mg/m 3);Ce的加入优化了催化剂表面的孔隙结构,比表面积与和孔容积分别达到121.11 m 2/g、1.71 cm 3/g;MnCe(0.08)Ti催化剂在210℃通入体积分数为300×10-6(857.1 mg/m 3)的SO 2和8%的水蒸气,连续运行180 h过程中的脱硝效率均可保持在80%以上,具有良好的抗硫性和稳定性。     

MnOx/TiO2-ZrO2催化剂的制备及低温催化还原NO的研究

采用共沉淀法制备了TiO2-ZrO2复合氧化物,以其为载体采用等体积浸渍法制备了不同负载量的MnOx/Ti02-Zr02催化剂.低温下以NH3为还原剂考察了催化剂选择性催化还原(SCR)NO的活性.借助N2吸附、XRD、热重-差示扫描量热法(TG-DSC)对催化剂进行微观表征和分析.结果表明,负载量为5%时,生成的MnO2高度分散,NO的转化率较高;负载量为10%和15%时,出现MnO2晶相,NO的转化率有所下降.120-240℃、体积空速为10000 h-1的条件下,3种负载量的催化剂上NO转化率均大于90%.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

TiO2/活性炭负载光催化剂的制备与光催化性能

以粒状活性炭为载体,钛酸丁酯和乙醇为原料,用溶胶-凝胶法及浸渍法制备负载型TiO2光催化剂.通过加入不同分子量和质量的聚乙二醇降低催化剂表面TiO2的粒径,增大比表面积,提高TiO2/C光催化剂的吸附性和光催化活性.以XDA、SEM、TG-DTA、比表面积、亚甲蓝吸附值、钛的负载量及对亚甲蓝的光催化降解性能对催化剂样品进行了表征.结果表明加入1.0 g PEG2000所制备的TiO2/C前驱体经过450℃焙烧后,TiO2的平均晶粒尺寸为12.9 nm,其晶型为锐钛矿型,其比表面积为997.0m2·g-1,对亚甲蓝的吸附值比活性炭基体增加22.5%,100mg·L-1的亚甲蓝溶液用该催化剂在pH为1.0～9.25范围内,2.5 h的降解率达82.5%～96%.     

Au负载OMS-2催化剂的制备及其低温催化氧化性能

通过前掺杂法(QI),浸渍法(IM)和沉积-沉淀法(DP)3种方法制备了Au负载氧化锰八面体分子筛(OMS-2)Au/OMS-2催化剂,研究了制备方法和制备条件对其催化氧化CO活性的影响.采用X射线衍射(XRD)和BET比表面积测定等技术对所制样品进行表征.结果表明,沉积-沉淀法制备的Au/OMS-2-DP催化剂活性明显高于前掺杂法和浸渍法制备的催化剂,这与Au/OMS-2-DP催化剂比表面积较大和负载Au颗粒较小有关.制备条件(沉淀剂种类、制备溶液pH、Au负载量和催化剂焙烧温度)明显影响Au/OMS-2-DP催化剂的催化活性.对于各种不同的沉淀剂,以KOH为沉淀剂制备的催化剂活性最高,这可能与其无钝化作用,而且形成的Au颗粒较小有关;制备溶液的为最佳,当pH值过高或过低容易导致Au颗粒的聚集和Au沉淀量较少;XRD结果表明,当Au负载量为5wt%催化剂和催化剂焙烧为300℃时,所制备的催化剂颗粒最小,所得的催化剂活性最高.最佳条件制备的Au/OMS-2-DP催化剂活性较好,CO完全转化(100%)的温度为67℃.     

SO2对Mn-Cu-Ce/TiO2低温选择催化还原NO的影响

研究了SO2对Mn-Cu-Ce/TiO2选择催化还原 NO 的影响,并采用傅立叶变换红外光谱、x射线衍射光谱及暂态响应技术对Mn-Cu-Ce/TiO2催化剂的SO2中毒机理进行了探讨.结果表明,SO2 可强吸附在Mn-Cu-Ce/TiO2表面的 CuO 活性位上.并生成 CuSO4,由于 CuSO4 在低温时对SCR 反应有抑制作用,因而,催化剂的活性下降;暂态响应实验结果表明,Mn-Cu-Ce/TiO2催化剂上的SCR反应主要遵循 Langmuir-Hinshelwood机理.通过对催化剂进行硫酸化或 NO 预吸附,可以消除SO2对 Mn-Cu-Ce/TiO2的毒害作用.     

Effect of TiO2 surface properties on the SCR activity of NOx emission abatement catalyst

NOx emission abatement catalysts V2O5 supported on various TiO2 including anatase, rutile and mixture of both were investigated with various physico-chemical measurements such as BET, NH3-TPD, NARP, XRD and so on, and the effect of TiO2 surface properties on the SCR (selective catalytic reduction) activity of V20s/TiO2 catalysts was studied. It was found that the TiO2 surface properties had strong affect on the SCR activity of V2Os/TiO2 catalysts. The stronger acidic property resulted in the higher exposure of active sites as well as the higher SCR activity.     

Effects of support acidity on the reaction mechanisms of selective catalytic reduction of NO by CH4 in excess oxygen

The reaction mechanisms of selective catalytic reduction (SCR) of nitric oxide (NO) by methane (CH₄) over solid superacid-based catalysts were proposed and testified by DRIFTS studies on transient reaction as well as by kinetic models. Catalysts derived from different supports would lead to different reaction pathways, and the acidity of solid superacid played an important role in determining the reaction mechanisms and the catalytic activities. Higher ratios of Br?nsted acid sites to Lewis acid sites would lead to stronger oxidation of methane and then could facilitate the step of methane activation. Strong Br?nsted acid sites would not necessarily lead to better catalytic performance, however, since the active surface NO_y species and the corresponding reaction routes were determined by the overall acidity strength of the support. The reaction routes where NO₂ moiety was engaged as an important intermediate involved moderate oxidation of methane, the rate of which could determine the overall activity. The reaction involving NO moiety was likely to be determined by the step of reduction of NO. Therefore, to enhance the SCR activity of solid superacid catalysts, reactions between appropriate couples of active NO_y species and activated hydrocarbon intermediates should be realized by modification of the support acidity.     

Effect of MoO3 on vanadium based catalysts for the selective catalytic reduction of NOx with NH3 at low temperature

The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.     

低温等离子体改性对Fe2O3/ACF低温选择性催化还原NO的影响

利用N2低温等离子体对过量溶液浸渍法制备的Fe2O3/ACF（活性炭纤维）催化剂进行了改性,运用BET比表面积、扫描电子显微镜（SEM）、X射线衍射光谱（XRD）和傅立叶变换红外光谱（FT\|IR）对催化剂进行表征.同时,对催化剂的NH3选择性催化还原（SCR）NO的催化性能进行了研究.结果表明,活性组分最佳负载量的质量分数为10.3%;N2等离子体改性最优改性电压为6kV,改性时间为3min;随着反应温度的升高,空白ACF上NO转化率先升高再下降,而催化剂上NO转化率呈上升趋势.在NO体积分数1000×10-6、NH3体积分数1000×10-6、O2体积分数5%、空速10040h-1和反应温度240℃的条件下,催化剂3.7%Fe2O3/ACF和10.3%Fe2O3/ACF经N2等离子体改性后,其NO转化率（相对于未改性的）分别提高了16.43%和6.84%.N2等离子体改性催化剂提高了活性组分在ACF上的分散度,增加了ACF表面的含氮官能团,从而提高了催化剂的SCR低温活性.     

焙烧温度对ZnSn水滑石结构及光催化性能的影响

采用共沉淀和热处理法合成了一系列ZnSn-LDHs/MMO光催化剂,利用X射线衍射(XRD)、N2吸附-脱附、傅里叶变换红外(FTIR)、紫外漫反射(UV-Vis-DRS)、光致发光光谱(PL)和电化学阻抗(EIS)等技术对其进行表征,并以甲基橙(MO)为降解物,考察其光催化性能.结果表明,ZnSn-LDHs在焙烧温度...     

Mn/TiO2和Mn-Ce/TiO2低温脱硝催化剂的抗硫性研究

在低温选择性催化还原(SCR)反应条件下考察了烟气残余SO2对Mn/TiO2和Mn-Ce/TiO2催化剂选择性催化还原活性的影响,同时对SO2的影响机理进行了探讨.结果发现,Mn/TiO2催化剂在SO2反应气氛中失活很快,硫铵盐的沉积和活性组分的硫酸化是催化剂失活的重要原因;Ce的加入可以有效地抑制催化剂活性组分的硫酸化,同时还能降低硫酸盐在催化剂表面的稳定性,从而可以提高催化剂的抗硫性.     

N/Ce doped graphene supported Pt nanoparticles for the catalytic oxidation of formaldehyde at room temperature

Pt catalysts with nitrogen-doped graphene oxide (GO) as support and CeO₂ as promoter were prepared by impregnation method,and their catalytic oxidation of formaldehyde (HCHO) at room temperature was tested.The Pt-CeO₂/N-rGO (reduced GO) with a mass fraction of 0.7% Pt and 0.8%CeO₂ exhibited an excellent catalytic performance with the 100% conversion of HCHO at room temperature.Physicochemical characterization demonstrated that nitrogendoping greatly increased the...     

Pd-W-Cu/γ-Al2O3催化氢还原脱硝的基本性能研究

采用浸渍法制备Pd-W-Cu/γ-Al2O3催化剂,用XRD和SEM方法对该催化剂进行了表征.以氢气作为还原剂,在间歇式反应器中对催化还原地下水中硝酸盐进行了实验研究,考察了催化剂制备方法对催化还原硝酸盐性能的影响.结果表明,W的添加改善了Pd的分散性,提高了催化剂的活性和选择性.金属Pd/W/Cu质量比、浸渍顺序和焙烧温度对催化性能有较大影响.Pd/W/Cu质量比为3∶1∶1,Pd、Cu和W3种金属组分同时浸渍,焙烧温度为400℃时,催化剂的活性和选择性最高.在NO3--N初始浓度为100mg·mL-1条件下,催化反应60min后水中NO3--N和NO2--N浓度均为0mg·mL-1,NH4+-N浓度为2.5mg·mL-1.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

Effect of TiO2 calcination temperature on the photocatalytic oxidation of gaseous NH3

Carbon-modified titanium dioxide(TiO2) was prepared by a sol-gel method using tetrabutyl titanate as precursor, with calcination at various temperatures, and tested for the photocatalytic oxidation(PCO) of gaseous NH3 under visible and UV light. The test results showed that no samples had visible light activity, while the TiO2 calcined at 400℃ had the best UV light activity among the series of catalysts, and was even much better than the commercial catalyst P25. The catalysts were then characterized by X-ray diffractometry, Brunauer-Emmett-Teller adsorption analysis, Raman spectroscopy, thermogravimetry/differential scanning calorimetry coupled with mass spectrometry, ultraviolet-visible diffuse reflectance spectra, photoluminescence spectroscopy and in situ diffuse reflectance infrared Fourier transform spectroscopy. It was shown that the carbon species residuals on the catalyst surfaces induced the visible light adsorption of the samples calcined in the low temperature range( 300℃). However, the surface acid sites played a determining role in the PCO of NH3 under visible and UV light over the series of catalysts. Although the samples calcined at low temperatures had very high SSA, good crystallinity, strong visible light absorption and also low PL emission intensity, they showed very low PCO activity due to their very low number of acid sites for NH3 adsorption and activation. The TiO2 sample calcined at 400℃ contained the highest number of acid sites among the series of catalysts, therefore showing the highest performance for the PCO of NH3 under UV light.