Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

硅铝比和NiO对ZSM-5协同低温等离子体降解甲苯的影响

研究了不同硅铝比的ZSM-5与Ni/ZSM-5分子筛协同低温等离子体技术对甲苯降解性能的影响.以Ni O(Nickel Oxide)为活性组分,采用浸渍法对ZSM-5分子筛进行改性,利用氮气吸附脱附(BET)、X射线衍射仪(XRD)、X射线光电子能谱分析(XPS)、H_2程序升温还原(H_2-TPR)、NH_3程序升温脱附(NH_3-TPD)、Toluene程序升温脱附(Toluene-TPD)等技术表征样品的物理化学性质.考察了硅铝比对ZSM-5与Ni/ZSM-5分子筛体系中甲苯的吸附性能,研究了不同放电电压下硅铝比对甲苯降解率、碳平衡及二氧化碳选择性的影响,并采用气相色谱-质谱联用仪(GC-MS)分析了催化剂表面的有机产物.结果表明:硅铝比不但影响分子筛本身的物理化学特性(比表面积、氧化还原性能、表面酸性、疏水性等),还会影响Ni的负载形态和方式,更高的硅铝比与Ni O的负载能促进甲苯深度氧化,减少副产物,提高碳平衡和二氧化碳选择性.     

Size effect of Pt nanoparticles in acid-assisted soot oxidation in the presence of NO

Pt/Al₂O₃ catalysts with mean Pt particle size ranged from 2.7 to 7.1 nm were synthesized by chemical reduction method, and the sulfated counterparts were prepared by impregnation of sulfuric acid. The turnover frequency of platinum for soot oxidation under loose contact conditions in a feed flow containing NO and O₂ are positively correlated with the size of platinum. The sulfated Pt/Al₂O₃ exhibits higher catalytic activity for soot oxidation in the presence of NO despite their reduced ability for NO₂ production. Such a contradiction is more significant for those catalysts with smaller platinum particles. Herein, the catalysts were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscopy (TEM), inductive coupled plasma (ICP) emission spectrometry, CO chemisorption, thermogravimetric analysis (TGA), NH₃ temperature-programmed desorption (NH₃-TPD), NO temperature-programmed oxidation (TPO) and NO_x temperature-programmed desorption (TPD). Possible effect of Pt particle size for the catalytic oxidation of soot in the presence of NO was presented based primarily on the promoted NO₂ transfer efficiency onto the soot pushed by the acidic catalysts.     

Effect of Cu loading content on the catalytic performance of Cu-USY catalysts for selective catalytic reduction of NO with NH3

Series of Cu-USY zeolite catalyst with different Cu loading content were synthesized through simple impregnation method. The obtained catalysts were subjected to selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) performance evaluation, structural/chemical characterizations such as X-ray diffraction (XRD), N₂ adsorption/desorption, H₂ temperature-programmed reduction (H₂-TPR), NH₃ temperature-programmed desorption (NH₃-TPD) as well as detailed in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) experiments including CO adsorption, NH₃ adsorption and NO+O₂ in situ reactions. Results show that Cu-USY with proper Cu loading (in this work 5Cu-USY with 5 wt.% Cu) could be promising candidates with highly efficient NH₃-SCR catalytic performance, relatively low byproduct formation and excellent hydrothermal stability, although its SO₂ poisoning tolerability needs alleviation. Further characterizations reveal that such catalytic advantages can be attributed to both active cu species and surface acid centers evolution modulated by Cu loading. On one hand, Cu species in the super cages of zeolites increases with higher Cu content and being more conducive for NH₃-SCR reactivity. On the other hand, higher Cu loading leads to depletion of Brønsted acid centers and simultaneous formation of abundant Lewis acid centers, which facilitates NH₄NO₃ reduction via NH₃ adsorbed on Lewis acid centers, thus improving SCR reactivity. However, Cu over-introduction leads to formation of surface highly dispersed CuO_x, causing unfavorable NH₃ oxidation and inferior N₂ selectivity.     

Nano-sized alumina supported palladium catalysts for methane combustion with excellent thermal stability

Pd/Al₂O₃ catalysts supported on Al₂O₃ of different particle sizes were synthesized and applied in methane combustion. These catalysts were systematically characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), high resolution-transmission electron microscopy (HR-TEM), high-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM), H₂-temperature-programmed reduction (H₂-TPR), O₂-temperature-programmed oxidation (O₂-TPO), X-ray photoelectron spectroscopy (XPS), and X-ray absorption fine structure (XAFS). The characterization results indicated that nano-sized Al₂O₃ enabled the uniform dispersion of palladium nanoparticles, thus contributing to the excellent catalytic performance of these nano-sized Pd/Al₂O₃ catalysts. Among them, Pd/Al₂O₃-nano-10 (Pd/Al₂O₃ supported by alumina with an average particle size of 10 nm) showed superior catalytic activity and stability for methane oxidation under harsh practical conditions. It maintained excellent catalytic performance for methane oxidation for 50 hr and remained stable even after harsh hydrothermal aging in 10 vol.% steam at 800°C for 16 hr. Characterization results revealed that the strong metal-support interactions and physical barriers provided by Al₂O₃-nano-10 suppressed the coalescence ripening of palladium species, and thus contributed to the superior sintering resistance of the Pd/Al₂O₃-nano-10 catalyst.     

碱土金属钙沉积对Mn-Ce/TiO2低温SCR催化剂脱硝性能的影响

本研究采用浸渍法分别制备CaCl2、CaCO3和CaSO4这3种钙盐前驱体沉积的Mn-Ce/TiO2催化剂,通过分析催化剂活性与催化剂理化特性之间的关系,考察碱土金属钙沉积对Mn-Ce/TiO2低温SCR催化剂脱硝性能的影响.结果表明,钙的加入会导致催化剂中毒,且不同钙前驱体掺杂对催化剂中毒效应不同.CaCO3的沉积对Mn-Ce/TiO2催化剂脱硝效率的影响最小,而CaCl2沉积对催化剂活性抑制作用最为强烈.通过比表面积测试(BET)、X射线光电子能谱(XPS)、X射线晶体衍射(XRD)、程序升温脱附(TPD)等方法对不同催化剂进行表征发现,催化剂的晶型变化、孔道结构破坏、表面活性元素及酸性点位的减少是催化剂中毒的主要原因.     

Structures and catalytic performances of Me/SAPO-34 (Me = Mn, Ni, Co) catalysts for low-tem perature SCR of NOx by ammonia

Me/SAPO-34 (Me = Mn, Ni, Co) series of catalysts were prepared by a wetness impregnation method and investigated for the selective catalytic reduction of nitrogen oxides with ammonia (NH₃-SCR). Among them, Mn/SAPO-34 catalyst was found as the most promising candidate based on its superior low-temperature activity. The catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy images (TEM), nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction and desorption (TPR and TPD), and diffuse reflectance infrared Fourier transformed spectroscopy (DRIFTS) of NH₃/NO_x adsorption. Mn/SAPO-34 is obviously different from Ni/SAPO-34 and Co/SAPO-34 in the active species state and distribution. Surface MnO_x species which play an essential role in NO oxidation and NO₂ adsorption, act as better active sites than nickel and cobalt mostly in the form of the aluminates and silicates.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

Effect of CeO2 and Al2O3 on the activity of Pd/Co_3O_4/cordierite catalyst in the three-way catalysis reactions (CO/NO/CnHm)

The present article studies the effect of CeO₂ and Al₂O₃ on the activity of Pd/Co₃O₄/cordierite catalyst in conversion of NO, CO, C_nH_m. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO₂ on the properties of Pd/Co₃O₄/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O₂ and CO + NO) and total hexane oxidation (C₆H₁₄ + O₂). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO₂ addition promotes the SO₂ resistance of Pd/Co₃O₄/cordierite. The second support decreases the activity of Pd/Co₃O₄/cordierite catalyst in the reactions of CO and C₆H₁₄ with oxygen because of CoAl₂O₄ formation.     

低温等离子体结合锰基催化剂去除乙酸乙酯的研究

利用固态法和溶胶-凝胶法分别制备了钙钛矿（LaMnO₃）和八面体分子筛（OMS）两种锰基催化剂,在不同工况（输入电压、初始浓度、停留时间和催化剂放置量）条件下考察了等离子体催化对乙酸乙酯的降解特性.结果发现,锰基催化剂的加入显著提高了乙酸乙酯的去除率,减少了副产物的生成,并且OMS的催化活性高于LaMnO₃;此外,乙酸乙酯去除率随着电压的升高而增加,随着污染物初始浓度的增大而减少,并随停留时间的增长而变大;催化剂放置量为0.2 g时催化效果最佳.OMS催化剂在等离子体催化长期运行过程中表现出较好的稳定性.基于X射线衍射（XRD）、X射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）、比表面积测试（BET）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等手段对锰基催化剂物理化学性质的分析表明,OMS具有较高的催化活性主要归功于其拥有更高比例的Mn⁴⁺/（Mn³⁺+Mn⁴⁺）和吸附氧（O_ads）/晶格氧（O_latt）.     

Regeneration of commercial selective catalyst reduction catalysts deactivated by Pb and other inorganic elements

The regeneration of commercial SCR(Selective Catalyst Reduction) catalysts deactivated by Pb and other elements was studied.The deactivated catalyst samples were prepared by chemical impregnation with mixed solution containing K_2SO_4,Na_2SO_4,CaSO_4,Pb(NO_3)_2and NH_4H_2PO_4.A novel method combining Ethylenediaminetetraacetic acid disodium salt(EDTA-2Na) and H_2SO_4solution(viz.catalysts treated by dilute EDTA-2Na and H_2SO_4 solution in sequence) was used to recover the activity of deactivated samples,and the effect was compared with single H_2SO_4,oxalic acid,acetic acid,EDTA or HNO_3 solutions.The surface structure,acidity and reducibility of samples were characterized by N_2adsorption–desorption,inductively coupled plasma optical emission spectrometer(ICP-OES),scanning electron microscopy(SEM),X-ray diffraction(XRD),X-ray fluorescence(XRF),H-2-temperature programmed section(H_2-TPR),NH3-temperature programmed desorption(NH3-TPD) and in situ DRIFTS.Impurities caused a decrease of specific surface area and surface reducibility,as well as Br?nsted acid sites,and therefore led to severe deactivation of the SCR catalyst.The use of an acid solution alone possibly eliminated the impurities on the deactivated catalyst to some extent,and also increased the specific surface area and Br?nsted acid sites and promoted the surface reducibility,thus recovered the activity partially.The combination of EDTA-2Na and H_2SO_4 could remove most of the impurities and improve the activity significantly.The removal of Pb should be an important factor for regeneration.Due to a high removal rate for Pb and other impurities,the combination of EDTA-2Na and H_2SO_4 solutions provided the best efficiency.     

H2S匀圆杂选择性催化氧化工艺及催化剂研究现状

论述了石油流化催化裂化烟气中H2S气体的选择性催化氧化处理工艺和工艺中所使用的各种类型选择性氧化催化剂.目前已发展并投入使用的选择性氧化工艺主要有:Superclaus工艺、Euroclaus工艺、Clinsulf-Do工艺、BSR/Hi-Activity工艺、Selectox工艺和Modop工艺等,各工艺具有不同的特点和应用范围.H2S选择氧化催化剂主要包括以下几种体系:碳体系、SiC载体体系、分子筛体系、氧化物体系和柱撑黏土体系等.其中碳体系和氧化物体系的研究开展的较早较多,关于分子筛体系的研究近期有所减少,SiC是研究人员认为非常有潜力的一个载体体系,其相关体系研究也一直在进行之中,柱撑黏土体系还处于初步研究阶段,离实际应用尚有距离.     

纳米CeO2催化氧化甲苯的形貌效应研究

采用水热法合成CeO2纳米棒、纳米颗粒和纳米立方体,利用XRD、BET-N2、TEM/HRTEM、Raman、O2-TPD和H2-TPR等表征手段进行表征,并利用连续流固定床反应法研究各催化剂对甲苯的催化氧化性能.结果表明,CeO2纳米棒因具有高比表面积和细颗粒尺寸,且表面主要暴露高活性的{100}/{110}晶面,拥有更多的氧空位和高活性氧物种,因此,催化活性最高,CeO2纳米颗粒次之,立方体最低.原位红外甲苯催化氧化机理分析进一步表明,CeO2纳米颗粒和纳米立方体上生成的羧酸盐物质难以进一步深度氧化,而纳米棒能在贫氧和低温条件下诱导甲苯的完全氧化和产物脱附,使甲苯得以快速降解.     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

不同SAPO分子筛负载MnOx催化剂的低温NH3-SCR性能研究

以磷酸硅铝分子筛SAPO-5、SAPO~(-1)1和SAPO-34为载体,采用乙醇分散法制备了用于低温氨选择性还原(NH_3-SCR)NO_x的分子筛负载MnO_x催化剂.活性测试结果显示,3种分子筛催化剂均展现出优良的NH_3-SCR活性,但三者在低温区间的SCR活性存在较明显差异,其SCR活性顺序如下:MnO_x/SAPO-34MnO_x/SAPO-5MnO_x/SAPO~(-1)1.借助XRD、N2吸附-脱附、XPS、H2-TPR、NH_3-TPD、NH_3FT-IR等技术对催化剂的表面活性物种及表面酸性等进行表征分析,结果表明,MnO_x主要以无定型状态分散于载体上,负载后载体的比表面积和孔体积均有所下降.XPS和H2-TPR分析证实,不同分子筛载体上MnO_x的表面浓度与氧化态明显不同.NH_3-TPD和NH_3FT-IR分析揭示了催化剂表面均存在Bronsted酸位和Lewis酸位,其中,Lewis酸性位对低温SCR反应起着关键作用.研究表明,催化剂的催化性能会因载体不同而存在差异,高Mn4+表面浓度和丰富的Lewis酸性位对催化剂在低温区间实现优良的催化活性尤为重要.     

Selective catalytic reduction of nitrogen oxides over a modified silicoaluminophosphate commercial zeolite

Nitrogen oxides(NO_x:NO,NO_2)are a concern due to their adverse health effects.Diesel engine transport sector is the major emitter of NO_x.The regulations have been strengthened and to comply with them,one of the two methods commonly used is the selective catalytic reduction of NO_xby NH_3(NH_3-SCR),NH_3being supplied by the in-situ hydrolysis of urea.Efficiency and durability of the catalyst for this process are highly required.Durability is evaluated by hydrothermal treatment of the catalysts at temperature above 800°C.In this study,very active catalysts for the NH_3-SCR of NO_xwere prepared by using a silicoaluminophosphate commercial zeolite as copper host structure.Characterizations by X-ray diffraction(XRD),scanning electron microscopy(SEM)and temperature programmed desorption of ammonia(NH_3-TPD)showed that this commercial zeolite was hydrothermally stable up to 850°C and,was able to retain some structural properties up to950°C.After hydrothermal treatment at 850°C,the NO_xreduction efficiency into NH_3-SCR depends on the copper content.The catalyst with a copper content of 1.25 wt.%was the most active.The difference in activity was much more important when using NO than the fast NO/NO_2reaction mixture.     

Highly catalytic activity of Mn/SBA-15 catalysts for toluene combustion improved by adjusting the morphology of supports

Rod-like, hexagonal and fiber-like SBA-15 mesoporous silicas were synthesized to support MnO_x for toluene oxidation. This study showed that the morphology of the supports greatly influenced the catalytic activity in toluene oxidation. MnO_x supported on rod-like SBA-15(R-SBA-15) displayed the best catalytic activity and the conversion at 230°C reached more than 90%, which was higher than the other two catalysts. MnO_x species consisted of coexisting MnO_2 and Mn_2O_3 on the three kinds of SBA-15 samples. Large amounts of Mn_2O_3 species were formed on the surface and high oxygen mobility was obtained on MnO_x supported on R-SBA-15, according to the H_2 temperature programmed reduction(H_2-TPR)and X-ray photoelectron spectroscopy(XPS) results. The Mn/R-SBA-15 catalyst with greater amounts of Mn_2O_3 species possessed a large amount of surface lattice oxygen, which accelerated the catalytic reaction rate. Therefore, the surface lattice oxygen and high oxygen mobility were critical factors on the catalytic activity of the Mn/R-SBA-15 catalyst.     

N-doped CoAl oxides from hydrotalcites with enhanced oxygen vacancies for excellent low-temperature propane oxidation

A series of nitrogen-doped CoAlO (N-CoAlO) were constructed by a hydrothermal route combined with a controllable NH₃ treatment strategy. The effects of NH₃ treatment on the physico-chemical properties and oxidation activities of N-CoAlO catalysts were investigated. In comparison to CoAlO, a smallest content decrease in surface Co³⁺ (serving as active sites) while a largest increased amount of surface Co²⁺ (contributing to oxygen species) are obtained over N-CoAlO/4h among the N-CoAlO catalysts. Meanwhile, a maximum N doping is found over N-CoAlO/4h. As a result, N-CoAlO/4h (under NH₃ treatment at 400°C for 4 hr) with rich oxygen vacancies shows optimal catalytic activity, with a T₉₀ (the temperature required to reach a 90% conversion of propane) at 266°C. The more oxygen vacancies are caused by the co-operative effects of N doping and suitable reduction of Co³⁺ for N-CoAlO/4h, leading to an enhanced oxygen mobility, which in turn promotes C₃H₈ total oxidation activity dominated by Langmuir-Hinshelwood mechanism. Moreover, in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTs) analysis shows that N doping facilities the decomposition of intermediate species (propylene and formate) into CO₂ over the catalyst surface of N-CoAlO/4h more easily. Our reported design in this work will provide a promising way to develop abundant oxygen vacancies of Co-based catalysts derived from hydrotalcites by a simple NH₃ treatment.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.