Microwave/SPME method to quantify pesticide residues in tomato fruits

A new analytical method using focused microwave-assisted extraction (FMAE), coupled with solid phase micro-extraction (SPME), has been elaborated to determine 25 pesticides used in tomato cultivation. Microwave energy was used for a fast and controlled heating of solvent to selectively extract compounds. Calibration curves were plotted from blank tomato samples spiked at different concentrations with standards. A linear response was obtained between 10 and 1000 μ g/Kg for pyrethroids and between 0.1 and 5000 μ g/Kg for other compounds. For all studied substances, the resulting correlation coefficient (r²) was greater than 0.99. Limits of detection (LOD) and quantification (LOQ) were measured lower than 8 and 25 μ g/Kg, respectively. The relative standard deviation (RSD) was determined below 15% for all pesticides. Field incurred tomato samples were used to validate the new FMAE/SPME method. Observed analysis results by using this technique were in good agreement compared to those obtained by two accredited trading laboratories using traditional methods. Four tomato samples, bought in a local market, were also tested with the FMAE/SPME method.     

Utilization of long duration high-volume sampling coupled to SPME-GC-MS/MS for the assessment of airborne pesticides variability in an urban area (Strasbourg,France) during agricultural application

Atmospheric samples have been collected between 14 March and 12 September 2012 on a 2-week basis (15 days of sampling and exchange of traps each 7 days) in Strasbourg (east of France) for the analysis of 43 pesticides. Samples (particle and gas phases) were separately extracted using Accelerated Solvent Extraction (ASE) and pre-concentrated by Solid Phase Micro-Extraction (SPME) before analysis by gas chromatography coupled to tandem mass spectrometry (GC-MS/MS). Four SPME consecutive injections at distinct temperatures were made in order to increase the sensitivity of detection for the all monitored pesticides. Currently used detected pesticides can be grouped in four classes; those used in maize crops (acetochlor, benoxacor, dicamba, s-metolachlor, pendimethalin, and bromoxynil), in cereal crops (benoxacor, chlorothalonil, fenpropimorph, and propiconazole), in vineyards (tebuconazole), and as herbicides for orchards, meadows of green spaces (2,4-MCPA, trichlopyr). This is in accordance with the diversity of crops found in the Alsace region and trends observed are in accordance with the period of application of these pesticides. Variations observed permit also to demonstrate that the long time sampling duration used in this study is efficient to visualize temporal variations of airborne pesticides concentrations. Then, long time high-volume sampling could be a simple method permitting atmospheric survey of atmospheric contamination without any long analysis time and consequently low cost.     

Analysis of acidic pesticides using in situ derivatization with alkylchloroformate and solid-phase microextraction (SPME) for GC-MS.

A solid-phase microextraction (SPME) method was developed for the analysis of acidic pesticide residues in water. The method utilizes in situ derivatization with butylchloroformate (BuCF), followed by on-line SPME extraction using a PDMS fibre, and analysis by GC-MS. Derivatives of the phenoxy acids mechlorprop (MCPP), dichlorprop (DCPP), MCPA and 2,4-D and their phenol degradation products 4-chloro-2-methylphenol and 2,4-dichlorophenol (DCP) were identified. Detection limits at 0.16-2.3 microg/l were achieved. Optimization of derivatization, ion strength, extraction time, SPME-fibre, desorption time and temperature are described. Standard curves in the range 0.5-10.0 microg/l were fitted to a second-degree polynomial. Standard deviation (n = 5) was below 10% for the phenol derivatives, but 20-50% for the phenoxy acids. For method verification groundwater samples from a field experiment were screened for content of MCPP and compared to the results from the HPLC analysis. A good agreement was obtained with respect to identification of positive samples, even though concentrations measured by the SPME were lower than with HPLC. Even if the precision and accuracy do not meet the demands for a strictly quantitative analysis, the SPME method is suitable for screening, because it is cheap, it can be automated, and uses smaller amounts of potential harmful solvents. Also, the method is less labour-intensive, as it requires a minimum of sample preparation when compared to traditional analyses. The acidic pesticides bentazon, dicamba, bromoxynil, ioxynil, dinoseb and DNOC were included in the study but could not be analysed by the current method.     

Determination of pesticides of different chemical classes in drinking water of the state of Santa Catarina (Brazil) using solid-phase microextraction coupled to chromatographic determinations

The evaluation of the concentration of pesticides in drinking water presents a real concern. In this study, a simple and rapid method based on solid-phase microextraction (SPME) followed by gas chromatography–mass spectrometry and electron capture detectors was developed aiming at multiclass determination of 23 pesticides regulated by the Brazilian legislation. The extraction was carried out by direct immersion mode (DI-SPME) using DVB/Car/PDMS fiber coating. In order to improve the extraction efficiency, parameters such as temperature, salting-out effect, and extraction time were optimized. The method was evaluated using drinking water samples spiked with the analytes at different concentrations, and it showed good linearity in the range studied. The values obtained for limits of quantification (LOQ) were below the limits established by Brazilian regulations. Accuracy and precision of the method exhibited satisfactory results, providing relative recoveries from 70 to 123.34% at three spiked levels, and the relative standard deviations ranged from 0.53 to 24.8%. The method was applied in 20 drinking water samples from 13 cities in the State of Santa Catarina, Brazil.

     

Monitoring the photochemical degradation of triclosan in wastewater by UV light and sunlight using solid-phase microextraction

Photo solid-phase microextraction (photo-SPME) is applied for the first time to study the photochemical behavior of an emerging pollutant, triclosan, in real contaminated wastewater samples using a solar simulator. In this study, water samples are extracted by SPME and then, the fiber coating is irradiated for a selected time. This on-fiber procedure, so-called photo-SPME, followed by gas chromatography-mass spectrometry makes it possible to study photodegradation kinetics and the generation of byproducts. Several photoproducts were identified in the real samples including the 2,8-dichlorodibenzo-p-dioxin, dichlorophenols and a compound tentatively identified as other DCDD congener or a dichlorohydroxydibenzofuran. Accordingly, it was possible to postulate main photodegradation mechanisms. Photo-SPME demonstrated slower kinetics in wastewater than in spiked ultrapure water probably due to the presence of dissolved organic matter. This technique was extensively compared with conventional aqueous photodegradation showing high similarity. The influence of pH on the triclosan photolysis and on the triclosan-dioxin conversion was also investigated in wastewater. Photodegradation of triclosan and formation of 2,8-DCDD occurred independently of sample pH. This study represents an advance in the use of photo-SPME to understand the photochemical fate of environmental organic pollutants and demonstrates its clear advantages with real samples.     

百菌清农药残留的SPE-GC检测

对环境水样中百菌清农药残留进行了SPE-GC分析方法研究。环境水样通过Florisil柱富集、净化,3 mL乙酸乙酯洗脱,GC-ECD进行分析检测。实验表明,百菌清农药残留在0.01~10 mg/L范围内线性关系良好,相关系数为0.9993。外标法定量,检出限为0.0035 mg/L,对实际水样进行加标回收,回收率范围在93.47%~100.14%之间,6次重复测定相对标准偏差在3.97%~4.96%之间,并将方法应用于周边环境地表水的检测。该方法具有简便,快速,准确,灵敏度高等特点,能满足环境水样中农药残留分析要求。     

Agricultural pesticide residues of farm runoff in the Okanagan Valley,British Columbia,Canada

The objectives of this study were to determine environmental occurrence and concentrations of selected currently-used-pesticides and some transformation products in agricultural farms in the Okanagan Valley (OKV), and to conduct a simple risk assessment of environmental pesticides levels detected in OKV on non-target aquatic organisms. The OKV is the tree fruit country of the Province of British Columbia where considerable amount of pesticides are applied annually. Water, sediment and soil samples were collected at eleven sites in early June and late September following rainfall events and/or extended periods of irrigation from drainage ditches and/or from small streams. Undisturbed reference sites were also sampled. Study results showed that forty of the eighty chemicals analyzed, including organochlorine, nitrogen-containing and organophosphate pesticides commonly used for OKV crops, were detected in runoff and small stream water samples. Among which, endosulfan-sulfate was the most frequently detected chemical. Also, azinophos-methyl (0.699–25.5 ng/L), diazinon (0.088–214 ng/L) exceeded, and α-, β- endosulfan, endosulfan sulphate approached the guidelines for the protection of aquatic life.     

Organochlorine pesticide distribution in an organic production system for cow's milk in Chiapas,Mexico

The objective of this study was to evaluate the presence of organochlorine pesticides in samples of forage, soil, water, and milk in four units of an organic production system for cow´s milk (samples of forage, milk, soil, and water) in Tecpatan, Chiapas, Mexico. The organochlorine pesticides were extracted from forage, soil and water based on the USEPA (2005) guideline and from milk based on the IDF 1991 guideline. The pesticides were identified and quantified by gas chromatography with electron capture detector (CG-ECD). In general, the highest average concentration of total pesticides was found in the samples of milk and forage (311 ± 328 and 116.5 ±77 ng g^?1 respectively). Although, the production systems analyzed are organic, organochlorine pesticides were detected in all environmental samples (forage, soil, water, and organic milk). Although no values surpassed the defined limits of Mexican and International regulation it is advisable that a monitoring program of contaminants in these production systems is continued.     

Controlled release and retarded leaching of pesticides by encapsulating in carboxymethyl chitosan /bentonite composite gel

A novel composite gel composed of carboxymethyl-chitosan (CM-chit) and bentonite (H-bent) was used as the carrier for encapsulating atrazine and imidacloprid to control their release in water and retard their leaching in soil. Strong interactions between CM-chit and H-bent in the composite were confirmed by FT-IR, and good dispersion of pesticides in the carrier was observed by SEM. According to the results of release experiments in water, the CM-chit/H-bent composite carrier showed double advantages of both encapsulation by the polymer and sorption by the bentonite. The time taken for 50 % of active ingredients to be released, t??, was prolonged to 572 h for atrazine and 24 h for imidacloprid, respectively. The difference between the two pesticides on release behavior was related to their hydrophobicity and water solubility. Leaching experiments through a soil layer showed that this novel carrier reduced the amount of pesticides available for leaching, and would be useful for diminishing the environmental pollution of pesticides.     

Agricultural pesticide residues of farm runoff in the Okanagan Valley, British Columbia, Canada

The objectives of this study were to determine environmental occurrence and concentrations of selected currently-used-pesticides and some transformation products in agricultural farms in the Okanagan Valley (OKV), and to conduct a simple risk assessment of environmental pesticides levels detected in OKV on non-target aquatic organisms. The OKV is the tree fruit country of the Province of British Columbia where considerable amount of pesticides are applied annually. Water, sediment and soil samples were collected at eleven sites in early June and late September following rainfall events and/or extended periods of irrigation from drainage ditches and/or from small streams. Undisturbed reference sites were also sampled. Study results showed that forty of the eighty chemicals analyzed, including organochlorine, nitrogen-containing and organophosphate pesticides commonly used for OKV crops, were detected in runoff and small stream water samples. Among which, endosulfan-sulfate was the most frequently detected chemical. Also, azinophos-methyl (0.699-25.5 ng/L), diazinon (0.088-214 ng/L) exceeded, and α-, β- endosulfan, endosulfan sulphate approached the guidelines for the protection of aquatic life.     

Comparison between solid-phase extraction methods for the chromatographic determination of organophosphorus pesticides in water

A solid-phase microextraction (SPME) procedure has been developed to extract eight organophosphorus pesticides (OPs) in water and the method was compared with a conventional solid phase extraction (SPE) technique. The extracted OPs were analyzed by gas chromatography using thermionic specific detection. Both extraction methods presented linear calibration at least over the concentration range investigated (100 to 1000 ng x mL(-1) for SPE and 1 to 100 ng x mL(-1) for SPME). SPME method presented higher sensitivity than SPE. The quantitation limits were between 0.1 to 1.0 ng x mL(-1) for SPME depending upon the analyte, and 100 ng x mL(-1) for SPE. The precision, as measured by the standard deviations (RSD), were in the range 3.6% to 5.8% for SPME and 2.4% to 9.2% for SPE. Along with the feature of being a solvent - free sampling technique, SPME offers additional benefits due to its high sensitivity, simplicity, and small size sample required (typically: SPE - 500 mL, SPME - 5 mL).     

COMPARISON BETWEEN SOLID–PHASE EXTRACTION METHODS FOR THE CHROMATOGRAPHIC DETERMINATION OF ORGANOPHOSPHORUS PESTICIDES IN WATER

A solid-phase microextraction (SPME) procedure has been developed to ex tract eight organophosphorus pesticides (OPs) in water and the method was compared with a conventional solid phase extraction (SPE) technique. The extracted OPs were analyzed by gas chromatography using thermionic specific detection. Both extraction methods presented linear calibration at least over the concentration range investigated (100 to 1000 ng.mL^?1 for SPE and 1 to 100 ng.mL^?1 for SPME). SPME method presented higher sensitivity than SPE. The quantitation limits were between 0.1 to 1.0 ng.mL^?1 for SPME depending upon the analyte, and 100 ng.mL^?1 for SPE. The precision, as measured by the standard deviations (RSD), were in the range 3.6 % to 5.8 % for SPME and 2.4 % to 9.2 % for SPE.

Along with the feature of being a solvent – free sampling technique, SPME offers additional benefits due to its high sensitivity, simplicity, and small size sample required (typically: SPE – 500 mL, SPME – 5 mL).     

Impact assessment of treated/untreated wastewater toxicants discharged by sewage treatment plants on health, agricultural, and environmental quality in the wastewater disposal area

Studies were undertaken to assess the impact of wastewater/sludge disposal (metals and pesticides) from sewage treatment plants (STPs) in Jajmau, Kanpur (5 MLD) and Dinapur, Varanasi (80 MLD), on health, agriculture and environmental quality in the receiving/application areas around Kanpur and Varanasi in Uttar Pradesh, India. The raw, treated and mixed treated urban wastewater samples were collected from the inlet and outlet points of the plants during peak (morning and evening) and non-peak (noon) hours. The impact of the treated wastewater toxicants (metals and pesticides) on the environmental quality of the disposal area was assessed in terms of their levels in different media samples viz., water, soil, crops, vegetation, and food grains. The data generated show elevated levels of metals and pesticides in all the environmental media, suggesting a definite adverse impact on the environmental quality of the disposal area. The critical levels of the heavy metals in the soil for agricultural crops are found to be much higher than those observed in the study areas receiving no effluents. The sludge from the STPs has both positive and negative impacts on agriculture as it is loaded with high levels of toxic heavy metals and pesticides, but also enriched with several useful ingredients such as N, P, and K providing fertilizer values. The sludge studied had cadmium, chromium and nickel levels above tolerable levels as prescribed for agricultural and lands application. Bio-monitoring of the metals and pesticides levels in the human blood and urine of the different population groups under study areas was undertaken. All the different approaches indicated a considerable risk and impact of heavy metals and pesticides on human health in the exposed areas receiving the wastewater from the STPs.     

Controlled release and retarded leaching of pesticides by encapsulating in carboxymethyl chitosan /bentonite composite gel

A novel composite gel composed of carboxymethyl-chitosan (CM-chit) and bentonite (H-bent) was used as the carrier for encapsulating atrazine and imidacloprid to control their release in water and retard their leaching in soil. Strong interactions between CM-chit and H-bent in the composite were confirmed by FT-IR, and good dispersion of pesticides in the carrier was observed by SEM. According to the results of release experiments in water, the CM-chit/H-bent composite carrier showed double advantages of both encapsulation by the polymer and sorption by the bentonite. The time taken for 50 % of active ingredients to be released, t ₅₀, was prolonged to 572 h for atrazine and 24 h for imidacloprid, respectively. The difference between the two pesticides on release behavior was related to their hydrophobicity and water solubility. Leaching experiments through a soil layer showed that this novel carrier reduced the amount of pesticides available for leaching, and would be useful for diminishing the environmental pollution of pesticides.     

Continental bottled water assessment by stir bar sorptive extraction followed by gas chromatography-tandem mass spectrometry (SBSE-GC-MS/MS)

This study was aimed to determine the presence of 69 organic contaminants in 77 representative bottled waters collected from 27 countries all over the world. All water samples were contained in polyethylene terephthalate bottles. Target compounds were (1) environmental contaminants (including 13 polycyclic aromatic hydrocarbons (PAHs), 31 pesticides including organochlorine (OCPs), organophosphorus, and pyrethroids; 7 polychlorinated biphenyls (PCBs); and 7 triazines) and (2) plasticizers (including 6 phthalates and 5 other compounds). Samples were analyzed by stir bar sorptive extraction followed by gas chromatography-tandem mass spectrometry. PAHs, OCPs, PCBs, and triazines, which are indicators of groundwater pollution, were not detected in most of the samples, except for naphthalene (0.005–0.202 μg/L, n?=?16). On the other hand, plastic components were detected in 77 % of the samples. Most frequently detected compounds were dimethyl phthalate and benzophenone at concentrations of 0.005–0.125 (n?=?41) and 0.014–0.921 (n?=?32), respectively. Levels detected are discussed in terms of contamination origin and geographical distribution. Target compounds were detected at low concentrations. Results obtained showed the high quality of bottled water in the different countries around the world.     

Optimization of a methodology for the determination of organochlorine pesticides in surface water by SPME-GC/MS

In the present work experimental conditions were optimized for the analysis of organochlorine traces in water matrix using solid-phase microextraction (SPME) followed by gas chromatography with mass selective detector. The parameters including time of exposure of the fiber in the aqueous sample, fiber type, agitation speed, pH, ionic forces, temperature of adsorption, and time of desorption were evaluated. The best conditions to analyze organochlorine were obtained by using higher than room temperature, agitation of the sample, extraction time of 40 min, and polyacrylate fiber.     

Pesticide pollution remains severe after cleanup of a stockpile of obsolete pesticides at Vikuge, Tanzania

High levels of DDT residues and hexachlorocyclohexanes (HCHs) were found in soil, well water, and surface water around a collapsed pesticide storage shed at Vikuge Farm, Tanzania. Residues of DDT and HCHs were found at three soil depths down to 50 cm. Surface soil samples contained up to 28% total DDT and 6% total HCH residues. Water samples had concentrations of up to 30 microg L(-1) of organochlorine pesticides. Other compounds detected were aldrin, azinphos-methyl, carbosulfan, gamma-chlordane, chlorprofam, heptachlor, hexazinone, metamitron, metazachlor, pendimethalin, and thiabendazole. Although the visible remains of pesticides have been removed, the remaining soil is itself hazardous waste and poses a risk to the environment and the inhabitants of the surrounding villages. These findings show the necessity to follow up the environmental situation at former storage sites of obsolete stocks of pesticides, and that the environmental problems are not necessarily solved by removing the visible remains.     

Solid-phase microextraction coupled with atomic emission spectroscopy--rapid screening for volatile chlorinated compounds

Solid-phase microextraction (SPME) coupled with atomic emission spectroscopy was evaluated as a rapid screening tool for volatile halogenated compounds in water samples. After extraction, the SPME fiber was introduced to the injector where the analytes were rapidly and efficiently desorbed. The analytes entered the detector over a short period of time and produced one well-defined analyte signal. Element selective responses were measured to confirm the presence and to roughly estimate the content of volatile compounds. The total time for extraction and detection was approximately 5 min, which makes this method a rapid and promising technique for determination of total amount of volatile halogenated compounds. The proposed technique may prove useful as a screening test in order to pinpoint the samples that need further assessment by capillary gas chromatography.     

Evaluation of activated carbon fiber filter for sampling of organochlorine pesticides in environmental water samples

A simple method for quantitative analyses of organic chlorine pesticides (OCPs) in environmental water samples such as rainwater, river water and seawater using activated carbon fiber filters (ACFF) is described. ACFF was used as adsorbent to collect the chemicals in water samples. The collection of OCPs was completed almost for one day by stirring the mixture of the sample and the ACFF chips at room temperature. The adsorbed OCPs on the ACFF could be extracted easily with toluene-ethanol (4:1) mixed solvent. The purified extract by a florisil column chromatograph was followed by the analysis using high-resolution gas chromatograph/high-resolution mass spectrometer. Recoveries of OCPs spiked to actual samples such as rainwater, river water and seawater samples were approximately more than 80%, and the coefficients of variations were within 10%. This method was applied to the actual samples and was confirmed to be applicable for monitoring sub-ng/l level OCPs in environmental water samples.     

Sampling atmospheric pesticides with SPME: Laboratory developments and field study

To estimate the atmospheric exposure of the greenhouse workers to pesticides, solid phase microextraction (SPME) was used under non-equilibrium conditions. Using Fick's law of diffusion, the concentrations of pesticides in the greenhouse can be calculated using pre-determined sampling rates (SRs). Thus the sampling rates (SRs) of two modes of SPME in the lab and in the field were determined and compared. The SRs for six pesticides in the lab were 20.4-48.3 mL min⁻¹ for the exposed fiber and 0.166-0.929 mL min⁻¹ for the retracted fiber. In field sampling, two pesticides, dichlorvos and cyprodinil were detected with exposed SPME. SR with exposed SPME for dichlorvos in the field (32.4 mL min^-1) was consistent with that in the lab (34.5 mL min^-1). SR for dichlorvos in the field (32.4 mL min⁻¹) was consistent with that in the lab (34.5 mL min⁻¹). The trends of temporal concentration and the inhalation exposure were also obtained.