Sorption of the fumigant 1,3-dichloropropene on soil

The fumigant 1,3-dichloropropene (1,3-D) is considered a major replacement to methyl bromide, which is to be phased out of use in the United States by 2005. The main purpose of this study was to evaluate soil-water partitioning of 1,3-D in two California agricultural soils (Salinas clay loam and Arlington sandy loam). The partition coefficients (Kd and Kf) were determined by directly measuring the concentration of 1,3-D in the solid phase (Cs) and aqueous phase (Cw) after batch equilibration. In the Salinas clay loam, the Kf of cis-1,3-D in adsorption and desorption isotherms was 0.47 and 0.54, respectively, with respective values of 0.39 and 0.49 for trans-1,3-D. This slight hysteric effect suggests that a different range of forces are involved in the adsorption and desorption process. Since n was near unity in the Freundlich equation, the Freundlich isotherms can also be approximated using the liner isotherm. At 25 degrees C, the Kd of the 1,3-D isomers in both soils ranged from 0.46 to 0.56, and the Koc (organic matter partition coefficient) ranged from 58 to 70. The relatively low Kd values and a Koc that falls within the range of 50-150, suggests that 1,3-D is weakly sorbed and highly mobile in these soils. Understanding the sorption behavior of 1,3-D in soil is important when developing fumigation practices to reduce the movement of 1,3-D to the air and groundwater.     

Sorption–desorption of imidacloprid onto a lacustrine Egyptian soil and its clay and humic acid fractions

Sorption–desorption of the insecticide imidacloprid 1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine onto a lacustrine sandy clay loam Egyptian soil and its clay and humic acid (HA) fractions was investigated in 24-h batch equilibrium experiments. Imidacloprid (IMDA) sorption–desorption isotherms onto the three sorbents were found to belong to a non-linear L-type and were best described by the Freundlich model. The value of the IMDA adsorption distribution coefficient, Kd_ads, varied according to its initial concentration and was ranged 40–84 for HA, 14–58 for clay and 1.85–4.15 for bulk soil. Freundlich sorption coefficient, Kf_ads, values were 63.0, 39.7 and 4.0 for HA, clay and bulk soil, respectively. The normalized soil Koc value for imidacloprid sorption was ～800 indicating its slight mobility in soils. Nonlinear sorption isotherms were indicated by 1/n_ads values <1 for all sorbents. Values of the hysteresis index (H) were <1, indicating the irreversibility of imidacloprid sorption process with all tested sorbents. Gibbs free energy (ΔG) values indicated a spontaneous and physicosorption process for IMDA and a more favorable sorption to HA than clay and soil. In conclusion, although the humic acid fraction showed the highest capacity and affinity for imidacloprid sorption, the clay fraction contributed to approximately 95% of soil-sorbed insecticide. Clay and humic acid fractions were found to be the major two factors controlling IMDA sorption in soils. The slight mobility of IMDA in soils and the hysteresis phenomenon associated with the irreversibility of its sorption onto, mainly, clay and organic matter of soils make its leachability unlikely to occur.     

Tylosin Sorption to Silty Clay Loam Soils,Swine Manure,and Sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 μ mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K _f ) or K _d values, were calculated. K _f values for the silty clay loams were similar, not influenced by landscape position, and averaged 1350 with isotherm slopes ranging from 0.85 to 0.93. K _f values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K _d values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K _f values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Hydrolysis and soil sorption of insecticide pyraclofos

The hydrolysis of the insecticide pyraclofos in buffered solutions at pH 5.0, 7.0 and 9.0, and its sorption on four soils of different physicochemical properties were investigated. The results showed that the degradation of pyraclofos in buffered solutions followed pseudo-first-order kinetics. At 40°C, the rate constants for the hydrolysis of pyraclofos at pH 5.0, 7.0 and 9.0 were 0.0214, 0.1293, and 2.1656 d^?1, respectively. Pyraclofos was relatively stable under both acidic and neutral conditions, while it was readily hydrolyzed under basic conditions. The sorption of pyraclofos on four soils was well described by the Freundlich equation. The sorption constant, K _f, increased with an increase in soil organic carbon content, suggesting that organic carbon content was an important factor affecting sorption. The K _oc values for Xiaoshan clay loam soil, Hangzhou I clay loam soil, Hangzhou II soil, and Fuyang silt loam soil were 30.4, 6.7, 5.3, and 7.1, respectively. These results suggest that the sorption of pyraclofos on the tested soils was relatively weak.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48–72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K _d) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Acetamiprid,carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K _d and K _f coefficients from experimental data. The K _d values were utilized to calculate the partition coefficient normalized to soil organic carbon (K _oc ). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K _oc (mL g^{? 1}) values ranged in both soils from 98 – 3235, 1024 – 2644, 145 – 2631 and 104 – 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r² = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.     

Sorption and leaching of flucetosulfuron in soil

Abstract

The adsorption–desorption and leaching of flucetosulfuron, a sulfonylurea herbicide, was investigated in three Indian soils. Freundlich adsorption isotherm described the sorption mechanism of herbicide with adsorption coefficients (K_f) ranging from 17.13 to 27.99 and followed the order: Clayey loam?>?Loam?>?Sandy loam. The K_f showed positive correlation with organic carbon (OC) (r?=?0.910) and clay content (r?=?0.746); but, negative correlation with soil pH (r = ?0.635). The adsorption isotherms were S-type suggesting that herbicide adsorption was concentration dependent and increased with increase in concentration. Desorption followed the sequence: sandy loam?>?clayey loam?>?loam . Hysteresis (H) was observed in all the three soils with H?<?1. Leaching of flucetosulfuron correlated positively with the soil pH; but, negatively with the OC content. Sandy loam soil (OC- 0.40%, pH ?7.25) registered lowest adsorption and highest leaching of flucetosulfuron while lowest leaching was found in the loam soil (pH ? 7.89, OC ? 0.65%). The leaching losses of herbicide increased with increase in the rainfall intensity. This study suggested that the soil OC content, pH and clay content played important roles in deciding the adsorption–desorption and leaching behavior of flucetosulfuron in soils.     

Surfactant solubilization of hydrophobic compounds in soil and water

The soil/water partition coefficient (K_d) of hexachlorobenzene (HCB) ranged from 220 1/kg to 1800 1/kg for eight soils having a wide range of physico-chemical properties. K_d normalised to soil organic carbon (K_oc) was found to be 28000 ± 4800 1/kg. Anionic surfactant dodecylsulphate (DS) present at concentrations above the critical micellar concentration (CMC) caused reductions in the apparent soil/water partition coefficient (K_d ^*) in the range of 3–26 times for most soils and up to 36–91 times for sandy soils. Below CMC, at environmentally relevant surfactant concentrations, K_d ^* was reduced by a factor of 1–13. For clay and calcareous soils significant adsorption/complexation/precipitation of DS occurred. At the lowest DS concentration this produced a two-fold increase in K_d ^*. At increasing DS concentrations this effect was shielded by the solubihzing effect from DS. Monomer (K_mn) and micellar (K_mc) surfactant/water partition coefficients for HCB were determined to be, 980 ± 190 1/kg and 21000 ± 1600 1/kg, respectively.     

Adsorption-desorption and leaching of pyraclostrobin in Indian soils

Pyraclostrobin is a new broad-spectrum foliar applied and seed protectant fungicide of the strobilurin group. In this paper, adsorption-desorption of pyraclostrobin has been investigated in three different soils viz. Inceptisol (sandy loam, Delhi), Vertisol (sandy clay, Hyderabad) and Ultisol (sandy clay loam, Thrissur). Effect of organic matter and clay content on sorption was also studied in Inceptisol of Delhi. Leaching potential of pyraclostrobin as influenced by rainfall was studied in intact soil columns to confirm the results of adsorption-desorption studies. The adsorption studies were carried out at initial concentrations of 0.05, 0.1, 0.5, 1 and 1.5 μg mL^?1. The distribution coefficient (K_d) values in three test soils ranged from 4.91 to 18.26 indicating moderate to high adsorption. Among the three test soils, adsorption was the highest in Ultisol (K_d 18.26), followed by Vertisol (K_d 9.87) and Inceptisol (K_d 4.91). K_F value was also highest for Ultisol soil (66.21), followed by Vertisol (40.88) and Inceptisol (8.59). S-type adsorption isotherms were observed in all the three test soils. K_d values in organic carbon-removed soil and clay-removed soil were 3.57 and 2.83 respectively, indicating lower adsorption than normal Inceptisol. Desorption studies were carried out at initial concentrations of 0.5, 1 and 1.5 μg mL^?1. Desorption was the greatest in Inceptisol, followed by Vertisol and Ultisol. Amounts of pyraclostrobin desorbed in three desorption cycles for different concentrations were 23.1–25.3%, 9.4–20.7% and 8.1–13.6% in Inceptisol, Vertisol and Ultisol respectively. Desorption was higher in clay fraction-removed and organic carbonremoved soils than normal Inceptisol. Desorption was slower than adsorption in all the test soils, indicating hysteresis effect (with hysteresis coefficient values varying from 0.05 to 0.20). Low values of hysteresis coefficient suggest high hysteresis effect indicating easy and strong adsorption, and slow desorption, of pyraclostrobin in soils. Higher hysteresis coefficient values in organic carbon removed soil (0.25–0.30) and clay fraction removed soil (0.28–0.36) as compared to normal Inceptisol soil suggest relatively weak adsorption and easy desorption of pyraclostrobin. Results of regression analysis suggest that the organic matter and pH of the soil play a major role in adsorption of pyraclostrobin. Leaching studies were carried out in intact soil columns in Inceptisol. The columns were leached with different amounts of water simulating different amounts of rainfall. The results suggest that most of the pyraclostrobin residues will remain present in the top soil layers even under high rainfall conditions and chances of pyraclostrobin moving to lower soil depth are almost negligible.     

Behavior of Two Phenyl Urea Herbicides in Clayey Soils and Effect of Alternating Dry-Wet Conditions on their Availability

Adsorption and mobility of linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and diuron (3-(3,4-dichlorophenyl)-1, 1-dimethylurea) were studied in clayey soils from the Gharb area (Morocco). Soils A and B were planted with sun flower (Helianthus annuus) while soil C was planted with sugar cane (Saccharum offcinarum). Adsorption was studied for linuron in soils A and B, while mobility was studied only in soil B. Adsorption data were found to fit the Freundlich equation with correlation coefficients r² > 0.9. Freundlich coefficients (K_f, n_f) were in agreement with L and S isotherm types for soils A and B, respectively. Values of K_oc (195 and 102) indicate moderate adsorption. Desorption isotherms for linuron showed hysteresis for both soils. The pesticide would be more bound to soil A (H = 8.44) than to soil B (H = 4.01). The effect of alternating wet and dry conditions was tested for soils A and B. Results showed that retention would increase in soil subject to an additional wet and dry cycle. In the case of diuron isotherm was of type L in soil C. Desorption was noticeable at high concentrations and tended to decrease when concentrations diminished. Mobility of linuron was tested in polyvinyle chloride (PVC) columns, which received different treatments before their percolation. The pesticide was more mobile in a previously saturated column. In columns subject to a drying step after saturation with water, linuron mobility was greatly reduced.     

Sorption–desorption of indaziflam and its three metabolites in sandy soils

Indaziflam is a relatively new herbicide for which sorption–desorption information is lacking, and nothing is available on its metabolites. Information is needed on the multiple soil and pesticide characteristics known to influence these processes. For four soils, the order of sorption was indaziflam (N-[1R,2S)-2,3-dihydro-2,6-dimethyl-1H-inden-1-yl]-6-[(1R)-1-fluoroethyl]-1,3,5-triazine-2,4-diamine) (sandy clay loam: K_f = 5.9, 1/n_f = 0.7, K_foc = 447; sandy loam: K_f = 3.9, 1/n_f = 0.9, K_foc = 276) > triazine indanone metabolite (N-[(1R,2S)-2,3-dihydro-2,6-dimethyl-3-oxo-1H-inden-1-yl]-6-[(1R)-1-fluoroethyl]-1,3,5-triazine-2,4-diamine) (sandy clay loam: K_f = 2.1, 1/n_f = 0.8, K_foc = 177; sandy loam: K_f = 1.7, 1/n_f = 0.9, K_foc = 118) > fluoroethyldiaminotriazine metabolite (6-[(1R-1-Fluoroethyl]-1,3,5-triazine-2,4-diamine) (sandy clay loam: K_f = 0.3, 1/n_f = 0.9, K_foc = 28; sandy loam: K_f = 0.3, 1/n_f = 0.9, K_foc = 22) = indaziflam carboxylic acid metabolite (2S,3R)-3-[[4-amino-6-[(1R)-1-fluoroethyl]-1,3,5-triazin-2-yl]amino]-2,3-dihydro-2-methyl-1H-indene-5-carboxylic acid) (sandy clay loam: K_f = 0.3, 1/n_f = 0.9, K_foc = 22; sandy loam: K_f = 0.5, 1/n_f = 0.8, K_foc = 32). The metabolites being more polar than the parent compound showed lower sorption. Desorption was hysteretic for indaziflam and triazine indanone metabolite, but not for the other two metabolites. Unsaturated transient flow K_d's were lower than batch K_d's for indaziflam, but similar for fluoroethyldiaminotriazine metabolite. Batch K_d's would overpredict potential offsite transport if desorption hysteresis is not taken into account.     

Sorption and desorption of diuron on Typic Argiudoll,Oxic Argiudoll and on their clay fractions: environmental aspects

Abstract

The sorption and desorption of diuron by soil samples from Horizons A and B (HA and HB) and by their different clay fractions were investigated, using two soil samples, classified as Typic Argiudoll and Oxic Argiudoll. The sorption and desorption curves were adjusted to the Freundlich model and evaluated by parameters K_f, K_d and K_oc. Based on the data of groundwater ubiquity score (GUS), leachability index (LIX) and hysteresis index (HI), the risk of groundwater pollution was evaluated. The K_d values obtained for soil samples were between 4.5?mL g^?1 (Oxic Argiudoll – HB) and 15.9?mL g^?1 (Typic Argiudoll – HA) and between 1.13 and 14.0?mL g^?1 for the different mineral fractions, whereas the K_oc values varied between 276 (Oxic Argiudoll – HB) and 462 (Typic Argiudoll – HA). According to the parameter GUS, only Oxic Argiudoll – HB presented leaching potential, and based on the LIX index this same soil presented the highest leaching potential. Some samples presented low LIX and GUS values, indicating no leaching potential, but none presented HI results indicative of hysteresis, suggesting weak bonds between diuron and the soil samples and, hence, the risk of groundwater pollution by diuron.     

Sorption of chlorpyrifos and fonofos on four soils and turfgrass thatch using membrane filters

Abstract

Chemical transport in soil is a major factor influencing soil and water contamination. Four soils and turfgrass thatch, representing a wide range of organic carbon OC content were studied to determine sorption K_d and K_f parameters for the insecticides chlorpyrifos and fonofos. The batch equilibrium method was used. The concentration of insecticide was measured in the solution as well as in the solid phase to determine the most accurate sorption data. Four soils and thatch were equilibrated for 24 h at 22 ± 1^OC with aqueous insecticide solutions. Four concentrations of the insecticides, each <50% of their respective water solubilities, were selected for the experiments. After extraction with an organic solvent, the concentration of insecticides in the aqueous solution was determined by gas liquid chromatography using electron capture detection for chlorpyrifos, and nitrogen/phosphorus detection for fonofos. Data obtained were fitted to the log and simple linear form of the Freundlich equation. Mass balance Freundlich isotherm exponents n ranged between 0.82 and 0.93 for chlorpyrifos. 0.82 and 1.21 for fonofos, with r² ≥ 0.97. K_oc (percent of organic carbon %OC normalized Sorption coefficient) values were calculated by using experimentally developed K_d and K_f coefficients in relation to OC levels from 0.29 to 34.85%. K_d and K_f coefficients of both insecticides were positively correlated with OC (r² ≥ 0.96). organic matter OM (r² ≥ 0.96), and cation exchange capacity CEC (r² ≥ 0.90).     

Sorption of alpha and beta hydrophobic endosulfan in a Vertisol from southeast region of Turkey

Endosulfan has been applied to control numerous insects in a variety of food and non-food crops. Limited information is available on dynamics of this pesticide in the soil. The objective of this research was to determine the adsorption–desorption behavior of the alpha (α) and beta (β) endosulfan in a Vertisol from the southeast region of Turkey, where cotton is the main crop in the large irrigated lowlands. The α and β endosulfan were adsorbed considerably and Freundlich adsorption–desorption isotherms fitted the α and β endosulfan data (R² > 0.98). Freundlich adsorption coefficients (K_f) for the α endosulfan ranged between 21.63 and 16.33 while for the β endosulfan they were between 14.01 and 17.98 for the Ap and Bw2 horizons. The difference of K_f values of α and β endosulfan for two horizons were explained with the slight difference in the amount of organic matter and clay, but considerable difference in Fe contents of the two horizons. Alpha and β endosulfan K_fd values were 118.03 and 45.81 for the Ap and 48.08 and 68.71 for the Bw2 horizons. Higher adsorption and desorption behavior of the endosulfan isomers for the same horizon was attributed to poor physical bonding between the endosulfan molecule and the surfaces of fundamental soil particles. This fact is thought to increase the effective use of endosulfan in agriculture with a possibility of its movement to the surface and groundwater in the Vertisol studied.     

Effect of soil and sediment composition on acetochlor sorption and desorption

Background, aim, and scope  Herbicide fate and its transport in soils and sediments greatly depend upon sorption–desorption processes. Quantitative determination of herbicide sorption–desorption is therefore essential for both the understanding of transport and the sorption equilibrium in the soil/sediment–water system; and it is also an important parameter for predicting herbicide fate using mathematical simulation models. The total soil/sediment organic carbon content and its qualitative characteristics are the most important factors affecting sorption–desorption of herbicides in soil or sediment. Since the acetochlor is one of the most frequently used herbicides in Slovakia to control annual grasses and certain annual broad-leaved weeds in maize and potatoes, and posses various negative health effects on human beings, our aim in this study was to investigate acetochlor sorption and desorption in various soil/sediment samples from Slovakia. The main soil/sediment characteristics governing acetochlor sorption–desorption were also identified. Materials and methods  The sorption–desorption of acetochlor, using the batch equilibration method, was studied on eight surface soils, one subsurface soil and five sediments collected from the Laborec River and three water reservoirs. Soils and sediments were characterized by commonly used methods for their total organic carbon content, distribution of humus components, pH, grain-size distribution, and smectite content, and for calcium carbonate content. The effect of soil/sediment characteristics on acetochlor sorption–desorption was examined by simple correlation analysis. Results  Sorption of acetochlor was expressed as the distribution coefficient (K _d). K _d values slightly decreased as the initial acetochlor concentration increased. These values indicated that acetochlor was moderately sorbed by soils and sediments. Highly significant correlations between the K _d values and the organic carbon content were observed at both initial concentrations. However, sorption of acetochlor was most closely correlated to the humic acid carbon, and less to the fulvic acid carbon. The total organic carbon content was found to also significantly influence acetochlor desorption. Discussion  Since the strong linear relationship between the K _d values of acetochlor and the organic carbon content was already released, the corresponding K _oc values were calculated. Considerable variation in the K _oc values suggested that other soil/sediment parameters besides the total soil organic carbon content could be involved in acetochlor sorption. This was revealed by a significant correlation between the K _oc values and the ratio of humic acid carbon to fulvic acid carbon (C_HA/C_FA). Conclusions  When comparing acetochlor sorption in a range of soils and sediments, different K _d values which are strongly correlated to the total organic carbon content were found. Concerning the humus fractions, the humic acid carbon content was strongly correlated to the K _d values, and it is therefore a better predictor of the acetochlor sorption than the total organic carbon content. Variation in the K _oc values was attributed to the differences in distribution of humus components between soils and sediments. Desorption of acetochlor was significantly influenced by total organic carbon content, with a greater organic carbon content reducing desorption. Recommendations and perspectives  This study examined the sorption–desorption processes of acetochlor in soils and sediments. The obtained sorption data are important for qualitative assessment of acetochlor mobility in natural solids, but further studies must be carried out to understand its environmental fate and transport more thoroughly. Although, the total organic carbon content, the humus fractions of the organic matter and the C_HA/C_FA ratio were sufficient predictors of the acetochlor sorption–desorption. Further investigations of the structural and chemical characteristics of humic substances derived from different origins are necessary to more preciously explain differences in acetochlor sorption in the soils and sediments observed in this study.     

Adsorption behavior of RH‐5992 insecticide onto sandy and clay loam forest soils

Abstract

Adsorption‐desorption behavior of RH‐5992 [Mimic®, N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyl) hydrazine] in sandy and clay loam forest soils was studied using the batch equilibrium method. Adsorption was higher in the clay loam soil than in the sandy loam, and increased linearly with RH‐5992 concentration, but decreased with increasing pH and temperature. The adsorption data fit better to the Freundlich, than to the Langmuir equation. The K_D (linear adsorption constant) and K_F (Freundlich constant) were similar for each soil at 5, 15 and 25°C and decreased with increase of temperature, indicating that the enthalpy of adsorption was negative. The exponent of the Freundlich equation was close to unity for both soils at all three temperatures. The low E_a (energy of activation) indicated a diffusion‐controlled process during the initial stages of adsorption. The desorption isotherm differed from that of adsorption, and the linear desorption constant, K_D(d), was ca 25 times higher than the K_D, indicating that adsorption of RH‐5992 was not readily reversible. Evaluation of thermo‐dynamic parameters confirmed the presence of strong bonds between the solute and soil. These findings suggest that RH‐5992 has a limited potential for downward mobility leading to groundwater contamination.     

Sorption and desorption kinetics of diuron,fluometuron, prometryn and pyrithiobac sodium in soils

Abstract

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac‐sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r² value > 0.98. The herbicide sorption as measured by the distribution coefficient (K_d) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac‐sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the K_d values were normalised to organic carbon content of the soils (K_oC), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac‐sodium < fluometuron < prometryn < diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac‐sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step ω = [n_ad / n_de ‐1] x 100). Soil type and initial concentration had significant effect on ω. The effect of sorption and desorption properties of these four herbicides on the off‐site transport to contaminate surface and groundwater are also discussed in this paper.     

Sorption-desorption behavior of metsulfuron-methyl and sulfosulfuron in soils

Sorption of metsulfuron-methyl and sulfosulfuron were studied in five Indian soils using batch sorption method. Freundlich adsorption equation described the sorption of herbicides with K_f (adsorption coefficient) values ranging between 0.21 and 1.88 (metsulfuron-methyl) and 0.37 and 1.17 (sulfosulfuron). Adsorption isotherms were L-type suggesting that the herbicides sorption decreased with increase in the initial concentration of the herbicide in the solution. The K_f for metsulfuron-methyl showed good positive correlation with silt content (significant at p = 0.01) and strong negative correlation with the soil pH (significant at p = 0.05) while sorption of sulfosulfuron did not correlate with any of the soil parameter. Desorption of herbicides was concentration dependent and, in general, sulfosulfuron showed higher desorption than the metsulfuron-methyl. The study indicates that these herbicides are poorly sorbed in the Indian soil types and there may be a possibility of their leaching to lower soil profiles.     

Effect of moisture and compost on fate of azoxystrobin in soils

The effect of compost-amendment and moisture status on the persistence of azoxystrobin [methyl (E)-2-{2-(6-(2-cyanophenoxy) pyrimidin-4-yloxy) phenyl}-3-methoxyacrylate], a strobilurin fungicide, in two rice-growing soils was studied. Azoxystrobin is more sorbed in the silt loam (K _f – 4.66) soil than the sandy loam (K _f – 2.98) soil. Compost-amendment at 5 % levels further enhanced the azoxystrobin sorption and the respective K _f values in silt loam and sandy loam soils were 8.48 and 7.6. Azoxystrobin was more persistent in the sandy loam soil than the silt loam soil. The half–life values of azoxystrobin in nonflooded and flooded silt loam soil were 54.7 and 46.3 days, respectively. The corresponding half–life values in the sandy loam soils were 64 and 62.7 days, respectively. Compost application enhanced persistence of azoxystrobin in the silt loam soil under both moisture regimes and half-life values in non–flooded and flooded soils were 115.7 and 52.8 days, respectively. However, compost enhanced azoxystrobin degradation in the sandy loam soil and half-life values were 59 (nonflooded) and 54.7 days (flooded). The study indicates that compost amendment enhanced azoxystrobin sorption in the soils. Azoxystrobin is more persistent in non-flooded soils than the flooded soils. Compost applications to soils had mixed effect on the azoxystrobin degradation.     

Sorption of chlorinated solvents and degradation products on natural clayey tills

The sorption of chlorinated solvents and degradation products on seven natural clayey till samples from three contaminated sites was investigated by laboratory batch experiments in order to obtain reliable sorption coefficients (K_d values). The sorption isotherms for all compounds were nearly linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (K_d = 0.84-2.45 L kg⁻¹), followed by trichloroethylene (TCE, K_d = 0.62-0.96 L kg⁻¹), cis-dichloroethylene (cis-DCE, K_d = 0.17-0.82 L kg⁻¹) and vinyl chloride (VC, K_d = 0.12-0.36 L kg⁻¹). For chloroethanes, 1,1,1-trichloroethane (1,1,1-TCA) was most strongly sorbed (K_d = 0.2-0.45 L kg⁻¹), followed by 1,1-dichloroethane (1,1-DCA, K_d = 0.16-0.24 L kg⁻¹) and chloroethane (CA, K_d = 0.12-0.18 L kg⁻¹). This is consistent with the order of hydrophobicity of the compounds. The octanol-water coefficient (log K_ow) correlated slightly better with log K_d values than log K_oc values indicating that the K_d values may be independent of the actual organic carbon content (f_oc). The estimated log K_oc or log K_d for chlorinated solvents and degradation products determined by regression of data in this study were significantly higher than values determined by previously published empirical relationships. The site specific K_d values as well as the new empirical relationship compared well with calculations on water and soil core concentration for cis-DCE and VC from the Rugårdsvej site. In conclusion, this study with a wide range of chlorinated ethenes and ethanes - in line with previous studies on PCE and TCE - suggest that sorption in clayey tills could be higher than typically expected.