Sorption-Desorption of Atrazine and Diuron in Soils from Southern Brazil

The objective of this study was to investigate the behavior of sorption and desorption of the herbicides atrazine (6-chloro-N ²-ethyl-N ⁴-isopropyl-1,3,5-triazine-2,4-diamine) and diuron [3-(3,4-dichlorophenyl)-1,1-dimethyleurea] in soil samples from a typical lithosequence located in the municipality of Mamborê (PR), southern Brazil. Five concentrations of ¹⁴C-atrazine and ¹⁴C-diuron were used for both herbicides (0.48, 0.96, 1.92, 3.84, and 7.69 mg L^?1). Sorption of both herbicides correlated positively with the organic carbon and clay content of the soil samples. Sorption isotherms were well described by the Freundlich model. The slope values of the isotherm (N) ranged from 0.84 to 0.90 (atrazine) and from 0.75 to 0.79 (diuron) for the lithosequence samples. Sorption of diuron was high regardless of the soil texture or the concentration added. The desorption isotherms for atrazine and diuron showed good fit to the Freundlich equation (R ² ≥ 0,87). Atrazine slope values for the desorption isotherms were similar for the different concentrations and were much lower than those observed for the sorption isotherms. Significant hysteresis was observed in the herbicide desorption. When the two herbicides were compared, it was found that diuron (N = 0.06–0.22) presented more pronounced hysteresis than atrazine. The results showed that, quantitatively, a greater atrazine fraction applied to these soils remains available to be leached in the soil profile, as compared to diuron.     

Sorption and Desorption of Three Endocrine Disrupters in Soils

Sorption of the estrogens estrone (E1), 17β-estradiol (E2) and 17α-ethynylestradiol (EE2) on four soils was examined using batch equilibrium experiments with initial estrogen concentrations ranging from 10 to 1000 ng mL^?1. At all concentrations, >85% of the three estrogens sorbed rapidly to a sandy soil. E1 sorbed more strongly to soil than E2 or EE2. Partial oxidation of E2 to E1 was observed in the presence of soils. Autoclaving was more effective at reducing this conversion than inhibition with sodium azide or mercuric chloride, and had little effect on sorption, relative to the chemical microbial inhibitors. Sorption of EE2 was greater for fine-textured than coarse-textured soils, but greater than 90% of EE2 sorbed onto all four soils. The greatest degree of desorption of estrogens from the sandy soil occurred with the lowest initial concentration of 10 ng mL^?1 and reached levels ≥80% for E1 and E2. Desorption of EE2 was greater in coarser textured soils than finer-textured soils. Again, relative desorption from all soils was greatest with low initial concentrations. Therefore, at environmentally relevant concentrations, estrogens quickly sorb to soils, and soils have a large capacity to bind estrogens, but these endocrine-disrupting compounds can become easily desorbed and released into the aqueous phase.     

Two-Compartment Sorption of Phenanthrene on Eight Soils with Various Organic Carbon Contents

Sorption characteristics of phenanthrene (PHE) were studied on eight soils with organic carbon contents spanning over an order of magnitude using phase distribution relationships (PDRs) at 1 h, 48 h, and 720 h contact times. A new algebraic method was employed to describe the sorption characteristics at different time intervals (between 1 h and 48 h, and 1 h and 720 h). It was found that nonlinearity increased with increasing contact time and sorption that occurred in the subsequent time interval following the initial 1 h exhibited stronger isotherm nonlinearity. Sorption coefficients were positively correlated with the organic carbon contents of the soils. Detailed sorption dynamics were also examined on these soils. A two-compartment, first-order model was used to describe the sorption dynamics. The rate constants of the two compartments differed 18–170 times, suggesting the dissimilar sorption behaviors of the mathematically separated compartments. These two compartments were labeled fast and slow sorption compartment according to the rate constants. Calculation showed that the fast compartment accounted for over 80% of the overall sorption at the initial 1 h, while the slow compartment predominated the total sorption in the following 47 h. By combining the discussion of PDRs and sorption dynamics, the contributions of the two compartments to linear and nonlinear sorption were differentiated. The slow sorption compartment made a major contribution to nonlinear sorption and possibly to sequestration of organic pollutants by these soils.     

Tylosin Sorption to Silty Clay Loam Soils,Swine Manure,and Sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 μ mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K _f ) or K _d values, were calculated. K _f values for the silty clay loams were similar, not influenced by landscape position, and averaged 1350 with isotherm slopes ranging from 0.85 to 0.93. K _f values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K _d values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K _f values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Atrazine sorption and fate in a Ultisol from humid tropical Brazil

This study combined laboratory based microcosm systems as well as field experiments to evaluate the mobility of atrazine on a Ultisol under humid tropical conditions in Brazil. Results from sorption experiments fit to the Freundlich isotherm model [K(f) 0.99 mg kg(-1)/(mg l(-1))(1/n)], and indicate a low sorption capacity for atrazine in this soil and consequently large potential for movement by leaching and runoff. Microcosm systems using (14)C-atrazine to trace the fate of the applied herbicide, showed that 0.33% of the atrazine was volatilized, 0.25% mineralized and 6.89% was recorded in the leachate. After 60 d in the microcosms, 75% of the (14)C remained in the upper 5 cm soil layer indicating atrazine or its metabolites remained close to the soil surface. In field experiments, after 60 d, only 5% of the atrazine applied was recovered in the upper soil layers. In the field experiments atrazine was detected at a depth of 50 cm indicating leaching. Simulating tropical rain in field experiments resulted in 2.1% loss of atrazine in runoff of which 0.5% was adsorbed onto transported soil particles and 1.6% was in solution. Atrazine runoff was greatest two days after herbicide application and decreased 10 fold after 15 d. The use of atrazine on Ultisols, in the humid tropics, constitutes a threat to water quality, causing surface water and ground water pollution.     

Experimental Variability in Characterization of Cyfluthrin Sorption to Soil

To assess the risk of a pesticide to leach to groundwater or to run off to surface water after application, it is necessary to characterize the sorption of the pesticide to soil. For pyrethroids, their hydrophobicity, strong sorption to various materials, and low solubility make it difficult to accurately characterize sorption processes. The objective of this research was to evaluate the variability in cyfluthrin ((RS)-α -cyano-4-fluoro-3-phenoxybenzyl (1RS,3RS;1RS,3SR)-3-(2,2-dichlorovinyl)-2,2-dimethylcyclopropanecarboxylate) sorption to soil as affected by experiment conditions. To minimize cyfluthrin sorption on the walls of glass, silanized-glass, stainless steel, and PTFE centrifuge tubes, cyfluthrin solution was added to aqueous soil slurries or directly to soil, after which it was equilibrated with aqueous solution. Depending on the soil, variation in sorption coefficients, K _oc, obtained using different experimental methodologies with one soil can be comparable to the variation in K _oc values obtained for soils with different physical and chemical properties using one method. K _oc values for cyfluthrin ranged from 56,000 to 300,000 L kg^?1. Sorption methodology needs to be evaluated before sorption coefficients are used in predictive transport models.     

Sorption kinetics of atrazine and diuron in soils from southern Brazil

Sorption kinetics of atrazine and diuron was evaluated in soil samples from a typical landscape in Paraná. Samples were collected (0-20 cm) in a no-tillage area from Mamborê, PR, which has been cultivated under a crop rotation for the last six years. Six sampling points of the slope were selected to represent a wide range of soil chemical and physical properties found in this area. Radiolabeled tracers (14C-atrazine and 14C-diuron) were used and the radioactivity was detected by liquid scintillation counting (LSC). Sorption was accomplished for increasing equilibration periods (0.5, 1.5, 3, 6, 12, 24, and 48 h). Kinetics data fitted adequately well to Elovich equation, providing evidences that soil reaction occurs in two distinct stages: a fast, initial one followed by a slower one. During the fast phase, 34-42 and 71-79% of total atrazine and diuron applied were sorbed to soil samples. No important differences were found among combinations of soil and herbicide sorption during the slow phase. The unrealistic conditions under batch experiments should be overestimating sorption in the fast phase and underestimating diffusion in the slow phase. Sorption of both herbicides was positively correlated to organic carbon and clay contents of soils, but atrazine was much less sorbed than diuron, showing its higher potential to contaminate groundwater, specially in sandy, low organic carbon soils.     

Sorption of imidacloprid and its metabolites on tropical soils

Abstract

The sorption of imidacloprid (l‐[(6‐chloro‐3‐pyridinyl)‐methyl]‐N‐nitro‐2‐imidazolid‐inimine) (IMI) and its metabolites imidacloprid‐urea (l‐[(6‐chloro‐3‐pyridinyl)‐methyl]‐2‐imidazol‐idinone) (IU), imidacloprid‐guanidine (l‐[(6‐chloro‐3‐pyridinyl)‐methyl]‐4,5‐dihydro‐lH‐imidazol‐2‐amine) (IG), and imida‐cloprid‐guanidine‐olefin ( 1 ‐[(6‐chloro‐3‐pyridinyl)methyl]‐lH‐imidazol‐2‐amine) (IGO) was determined on six typical Brazilian soils. Sorption of the chemicals on the soil was characterized using the batch equilibration method. The range and order of sorption (Kd) on the six soils was IG (4.75–134) > IGO (2.87–72.3) > IMI (0.55 ‐16.9) > IU (0.31–9.50). For IMI and IU, Kd was correlated with soil organic carbon (OC) content and CEC, the latter due to the high correlation between OC and cation exchange capacity (CEC) (R²=0.98). For IG and IGO, there was no correlation of sorption to clay, pH, OC or CEC due to the high sorption on all soils. Average Koc values were IU = 170, IMI = 362, IGO = 2433, and IG = 3500. Although Kd and Koc values found were consistently lower than those found in soils developed in non‐tropical climates, imidacloprid and its metabolites were still considered to be slightly mobile to immobile in Brazilian soils.     

Sorption and transport of trichloroethylene in caliche soil

Sorption of TCE to the caliche soil exhibited linear isotherm at the high TCE concentrations (Co = 122-1300 mg L⁻¹) but Freundlich isotherm at the low concentration range (1-122 mg L⁻¹). Sorption strength of the carbonate fraction of the soil was about 100-fold lower than the sorption strength of soil organic matter (SOM) in the caliche soil, indicating weak affinity of TCE for the carbonate fraction of the soil. Desorption of TCE from the caliche soil was initially rapid (7.6 × 10⁻⁴ s⁻¹), then continued at a 100-fold slower rate (7.7 × 10⁻⁶ s⁻¹). Predominant calcium carbonate fraction of the soil (96%) was responsible for the fast desorption of TCE while the SOM fraction (0.97%) controlled the rate-limited desorption of TCE. Transport of TCE in the caliche soil was moderately retarded with respect to the water (R = 1.75-2.95). Flow interruption tests in the column experiments indicated that the rate-limited desorption of TCE controlled the non-ideal transport of TCE in the soil. Modeling studies showed that both linear and non-linear nonequilibrium transport models provided reasonably good match to the TCE breakthrough curves (r² = 0.95-0.98). Non-linear sorption had a negligible impact on both the breakthrough curve shape and the values of sorption kinetics parameters at the high TCE concentration (Co = 1300 mg L⁻¹). However, rate-limited sorption/desorption processes dominated at this concentration. For the low TCE concentration case (110 mg L⁻¹), in addition to the rate-limited sorption/desorption, contribution of the non-linear sorption to the values of sorption kinetics became fairly noticeable.     

Adsorption,Desorption, and Mobility of Permethrin in Malaysian Soils

Abstract

The adsorption, desorption, and mobility of permethrin in six tropical soils was determined under laboratory and greenhouse conditions. The six soils were selected from vegetable growing areas in Malaysia. Soil organic matter (OM) was positively correlated (r ² = 0.97) with the adsorption of permethrin. The two soils, namely, Teringkap 1 and Lating series with the highest OM (3.2 and 2.9%) released 32.5 and 30.8% of the adsorbed permethrin after four consecutive repetitions of the desorption process, respectively, compared to approximately 75.4% of the Gunung Berinchang soil with the lowest OM (1.0%) under the same conditions. The mobility of permethrin down the soil column was inversely correlated to the organic matter content of the soil. Permethrin residue penetrated only to the 10–15 cm zone in the Teringkap 1 soil with 3.2% OM but penetrated to a depth of more than 20 cm in the other soils. The Berinchang series soil with the lowest OM (1.0%) yielded leachate with 14.8% permethrin, the highest level in leachates from all the soils tested. Therefore, the possibility for permethrin to contaminate underground water may be greater in the presence of low organic matter content, which subsequently allows a higher percentage of permethrin to move downwards through the soil column.     

Sorption and cosorption of organic contaminant on surfactant-modified soils

Three kinds of soils were modified with the cationic surfactants, hexadecyltrimethylammonium (HDTMA) bromide and tetramethylammonium (TMA) bromide to increase their sorptive capabilities. Sorption of chlorobenzene in simulated groundwater by these soils was investigated. HDTMA-modified soil has a higher ability to sorb chlorobenzene from simulated groundwater than unmodified soil. TMA-modified soil did not show the superiority. HDTMA thus can be used to modify soil to improve its sorption capability. Cosorption of chlorobenzene in simulated groundwater in the absence or presence of nitrobenzene and dichloromethane on HDTMA-modified soil was also investigated. Nitrobenzene facilitated sorption of chlorobenzene on all HDTMA-modified soil. Dichloromethane did not influence the sorption of chlorobenzene by HDTMA-modified soil. The results suggest that HDTMA-modified soil is a highly effective sorbent for chlorobenzene and multiple organic compounds did not impede the uptake of chlorobenzene.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.     

Sorption of atrazine and phenanthrene by organic matter fractions in soil and sediment

Atrazine and phenanthrene (Phen) sorption by nonhydrolyzable carbon (NHC), black carbon (BC), humic acid (HA) and whole sediment and soil samples was examined. Atrazine sorption isotherms were nearly linear. The single-point organic carbon (OC)-normalized distribution coefficients (K_OC) of atrazine for the isolated HA1, NHC1 and BC1 from sediment 1 (ST1) were 36, 550, and 1470 times greater than that of ST1, respectively, indicating the importance of sediment organic matter, particularly the condensed fractions (NHC and BC). Similar sorption capacity of atrazine and Phen by NHC but different isotherm nonlinearity indicated different sorption domains due to their different structure and hydrophobicity. The positive relationship between (O + N)/C ratios of NHC and atrazine log K_OC at low concentration suggests H-bonding interactions. This study shows that sediment is probably a less effective sorbent for atrazine than Phen, implying that atrazine applied in sediments or soils may be likely to leach into groundwater.     

Behavior of perfluorinated compounds in soils during leaching experiments

Perfluorinated compounds (PFCs) can be detected worldwide in both, soil and water. In order to study the leaching behavior of this heterogeneous group of compounds in soil, flow-through column experiments have been conducted. Ten perfluoro carboxylates and four perfluoro sulfonates ranging from C4 to C14 in chain length, and contaminated sewage sludge, have been used to spike a standard soil. The aqueous column effluent was analyzed using liquid chromatography tandem mass spectrometry (LC-MS/MS) with direct injection. The observed percolation velocity seems to be strongly correlated with the length of the perfluorinated chain. Other factors that additionally contribute to the leaching behavior are the functional group of the PFC, the organic carbon content of the soil and the presence of other adsorbates. A mass balance calculation showed that perfluorobutanoic acid can adsorb strongly to the soil, when no PFC with longer carbon chain are present. Only about 60% of the added perfluorobutanoic acid could be detected in the percolate water. The missing amount started to elute again when longer chain PFC or stearate were added to the soil. Thus it would appear that larger and more lipophilic molecules can displace shorter PFC from their binding sites in the soil.The results of a monitoring study using 32 surface water samples and 150 groundwater samples confirm that the PFC with the highest concentrations in groundwater are the short chain PFC with less than 7 (fluorinated) carbon atoms. The dominating PFC in surface waters are perfluorooctanoic acid and perfluorooctane sulfonic acid.     

Sorption of heterocyclic compounds from a complex mixture of coal-tar compounds on natural clayey till

The sorption and desorption of heterocyclic organic compounds in a complex multisolute system to a natural clayey till was investigated. The composition of the solutes reflect a simplified composition of an aqueous phase in contact with coal tar. Sorption was studied for two ratios (s:l) of clayey till (solid) to aqueous phase (liquid). The effect of the complex mixture of solutes on sorption of the four heterocyclic compounds: benzofuran, dibenzofuran, benzothiophene, and dibenzothiophene is evaluated by comparison with their sorption measured in single-solute systems. Sorption of the four compounds is affected by the complex mixture, with sorption decreases for all four compounds at high s:l ratio indicating competitive sorption. The effect on sorption of the individual compounds is not related to solubility or hydrophobicity of the compounds. Freundlich-type isotherms are observed for all compounds in the high s:l-ratio experiments, but for the most hydrophobic compounds isotherms are close to linear. The sorption of N-compounds and benzofuran is apparently influenced by cation exchange and dipole–dipole attraction to clay minerals. At high concentrations a dramatic increase in the sorption of the most strongly sorbing compounds is observed in the low s:l-ratio experiment. The dramatic increase in sorption appears to be a result of multimolecular layer sorption or condensation on surfaces in the clayey till at high surface density of organic compounds, and the data are fitted by BET (Brunauer, Emmet, and Teller) type 2 isotherms. The increase may or may not be induced by the presence of N-heterocyclic compounds sorbed by cation exchange and dipole–dipole attraction. The desorption of the compounds was studied for the low s:l ratio where multimolecular layer formation apparently had occurred. Partially irreversible sorption, hysteric Langmuir type desorption with isotherms of very high K_l coefficient, or behaviour reflecting dissolution of a condensed phase is observed.     

Sorption of chlorinated solvents and degradation products on natural clayey tills

The sorption of chlorinated solvents and degradation products on seven natural clayey till samples from three contaminated sites was investigated by laboratory batch experiments in order to obtain reliable sorption coefficients (K_d values). The sorption isotherms for all compounds were nearly linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (K_d = 0.84-2.45 L kg⁻¹), followed by trichloroethylene (TCE, K_d = 0.62-0.96 L kg⁻¹), cis-dichloroethylene (cis-DCE, K_d = 0.17-0.82 L kg⁻¹) and vinyl chloride (VC, K_d = 0.12-0.36 L kg⁻¹). For chloroethanes, 1,1,1-trichloroethane (1,1,1-TCA) was most strongly sorbed (K_d = 0.2-0.45 L kg⁻¹), followed by 1,1-dichloroethane (1,1-DCA, K_d = 0.16-0.24 L kg⁻¹) and chloroethane (CA, K_d = 0.12-0.18 L kg⁻¹). This is consistent with the order of hydrophobicity of the compounds. The octanol-water coefficient (log K_ow) correlated slightly better with log K_d values than log K_oc values indicating that the K_d values may be independent of the actual organic carbon content (f_oc). The estimated log K_oc or log K_d for chlorinated solvents and degradation products determined by regression of data in this study were significantly higher than values determined by previously published empirical relationships. The site specific K_d values as well as the new empirical relationship compared well with calculations on water and soil core concentration for cis-DCE and VC from the Rugårdsvej site. In conclusion, this study with a wide range of chlorinated ethenes and ethanes - in line with previous studies on PCE and TCE - suggest that sorption in clayey tills could be higher than typically expected.     

Sorption of phenanthrene by dissolved organic matter and its complex with aluminum oxide nanoparticles

Intent of this study was to explore the potential application of polymerin, the polymeric, dissolved organic matter fraction from olive oil wastewaters, in technologies aimed at remediating hydrophobic organic compounds (HOCs) point-source pollution. Phenanthrene binding with polymerin was investigated. Moreover, the effect of addition of micro and nanoscale aluminum oxides (Al₂O₃) was studied, as well as sorption of polymerin on the oxides. Phenanthrene binding capacity by polymerin was notably higher than the sorption capacities for both types of Al₂O₃ particles. Polymerin sorption on nanoparticles was nearly 100 times higher than microparticles. In a three-phase system, using microparticles, higher phenanthrene sorption was found by adding into water polymerin, oxides and phenanthrene simultaneously. In contrast, using nanoparticles, a considerable enhancement of phenanthrene sorption was shown by adding phenanthrene to a pre-formed and dried polymerin-oxide complex. These findings support the application of polymerin, especially associated with Al₂O₃ nanoparticles, in remediation of water contaminated with HOCs. This work highlights the significant role of nanoparticles.     

Sorption of Cu, Pb and Cr on Na-montmorillonite: competition and effect of major elements

The competitive sorption among Cu, Pb and Cr in ternary system on Na-montmorillonite at pH 3.5, 4.5 and 5.5 and at different heavy metal concentrations, and the effect of varying concentrations of Al, Fe, Ca and Mg on the sorption of heavy metals were studied. Competitive sorption of Cu, Pb and Cr in ternary system on montmorillonite followed the sequence of Cr ? Cu > Pb. Moreover, the competition was weakened by the increase of pH while was intensified by the increase of heavy metal concentration. The sorption of heavy metal on montmorillonite was inhibited by the presence of Ca and Mg, while Al and Fe showed different patterns in affecting heavy metal sorption. Aluminum and Fe generally inhibited the sorption of heavy metal when the pH and/or concentration of major elements were relatively low. However, promoting effects on heavy metal sorption by Al and Fe were found at relatively high pH and/or great concentration of major elements. The inhibition of major elements on heavy metal sorption generally followed the order of Al > Fe > Ca ? Mg, while Fe was more efficient than Al in promoting the sorption of heavy metals. These findings are of fundamental significance for evaluating the mobility of heavy metals in polluted environments.     

Sorption of As, Cd and Tl as influenced by industrial by-products applied to an acidic soil: equilibrium and kinetic experiments

In situ stabilization of toxic elements in contaminated soils by the addition of amendments is being considered as an effective technique for remediation. In this paper, we performed both kinetics and equilibrium-based sorption experiments of three toxic elements (As, Cd and Tl) in soils amended with two by-products (phosphogypsum and sugar foam, rich in gypsum and calcium carbonate, respectively) to ascertain the feasibility of their application for improving the sorption capacity of As, Cd and Tl from the soil at 25, 35 and 50 °C. Kinetic studies indicated that the sorption follows a pseudo-second-order (PSO) kinetics and the sorption is a two-step diffusion process where both film and intraparticle diffusion played important roles in the sorption mechanisms of the elements. The Langmuir isotherms applied for sorption studies showed that the estimated maximum sorption capacity of the elements in control and amended soils decreased in the order of Cd > As > Tl. Using the thermodynamic equilibrium parameters obtained at different temperatures, the thermodynamic constants of sorption (ΔG, ΔH and ΔS) were also evaluated, indicating spontaneous and endothermic nature of the process, except Tl which was exothermic. An optimal scaling procedure was undertaken to determine the relationships between the kinetic and equilibrium sorption parameters. By means of statistical analysis it was seen that these inter-parametric relationships are dependent on the element nature.     

Paraquat Adsorption,Degradation, and Remobilization in Tropical Soils of Thailand

Paraquat adsorption, degradation, and remobilization were investigated in representative tropical soils of Yom River Basin, Thailand. Adsorption of paraquat in eight soil samples using batch equilibration techniques indicated that adsorption depended on soil characteristics, including exchangeable basic cations and iron content. Multiple regression analysis indicated significant contribution of exchangeable calcium percentage (ECP), total iron content (TFe) and exchangeable sodium percentage (ESP) to paraquat sorption (Q). ESP and TFe were significant at all adsorption stages, whereas ESP was significant only at the initial stage of paraquat adsorption. Adsorption studies using two soils representing clay and sandy loam textures showed that paraquat adsorption followed the Freundlich model, exhibiting a nonlinear sorption curve. Paraquat adsorption was higher in the clay soil compared to the sandy loam soil with K _f values of 787 and 18, respectively. Desorption was low with 0.04 to 0.17% and 0.80 to 5.83% desorbed in clay and sandy loam soil, respectively, indicating some hysteresis effect. Time-dependent paraquat adsorption fitted to the Elovich kinetic model indicated that diffusion was a rate-limiting process. Paraquat mobility and degradation studies conducted using both field and laboratory soil column experiments with clay soil showed low mobility of paraquat with accumulation only in the surface 0–5 cm layer under field conditions and in the 0–1 cm layer in a laboratory soil column experiment. Degradation of paraquat in soil was faster under field conditions than at ambient laboratory conditions. The degradation rate followed a first-order kinetic model with the DT₅₀ at 36–46 days and DT₉₀ around 119–152 days.