Estimation of residual MSW heating value as a function of waste component recycling

Recycling of packaging wastes may be compatible with incineration within integrated waste management systems. To study this, a mathematical model is presented to calculate the fraction composition of residual municipal solid waste (MSW) only as a function of the MSW fraction composition at source and recycling fractions of the different waste materials. The application of the model to the Lisbon region yielded results showing that the residual waste fraction composition depends both on the packaging wastes fraction at source and on the ratio between that fraction and the fraction of the same material, packaging and non-packaging, at source. This behaviour determines the variation of the residual waste LHV. For 100% of paper packaging recycling, LHV reduces 4.2% whereas this reduction is of 14.4% for 100% of packaging plastics recycling. For 100% of food waste recovery, LHV increases 36.8% due to the moisture fraction reduction of the residual waste. Additionally the results evidence that the negative impact of recycling paper and plastic packaging on the LHV may be compensated by recycling food waste and glass and metal packaging. This makes packaging materials recycling and food waste recovery compatible strategies with incineration within integrated waste management systems.     

Recovery of PET from packaging plastics mixtures by wet shaking table

Recycling requires the separation of materials appearing in a mass of wastes of heterogeneous composition and characteristics, into single, almost pure, component/material flows. The separation of materials (e.g., some types of plastics) with similar physical properties (e.g., specific gravity) is often accomplished by human sorting. This is the case of the separation of packaging plastics in municipal solid wastes (MSW). The low cost of virgin plastics and low value of recycled plastics necessitate the utilization of low cost techniques and processes in the recycling of packaging plastics. An experimental study was conducted to evaluate the feasibility of production of a PET product, cleaned from PVC and PS, using a wet shaking table. The wet shaking table is an environmentally friendly process, widely used to separate minerals, which has low capital and operational costs. Some operational variables of the equipment, as well as different feed characteristics, were considered. The results show that the separation of these plastics is feasible although, similarly to the mineral field, in somewhat complex flow sheets.     

Combustion kinetics of sewage sludge and combustible wastes

This study estimated the kinetics of the mono- and co-combustion of sewage sludge pellets and combustible wastes such as municipal solid waste (MSW) and refuse-derived fuel (RDF). Sewage sludge was manufactured into pellets with a diameter of 8, 12, or 16 mm and a length of 30 mm. The RDF was composed of paper and plastics and was formed into pellets with a diameter of 8 mm and a length of 30 mm. MSW samples were synthesized using combustible wastes such as garbage, paper, plastics, and wood. The MSW was adjusted to have a moisture content of around 40% after shredding to under 10 mm. A laboratory-scale batch type stoker incinerator was used for the combustion and the gas composition of the flue gas was measured. The activation energy was calculated using the experimental results, and then the relation of the decomposition rate and reaction time was evaluated using the shrinking core model. The decomposition rate of the sludge pellets decreased as their diameter and moisture content increased, and the co-combustion of sludge pellets and combustible waste was affected by the amount of combustible waste. The individual combustion rates of the cylindrical sludge pellets or RDF were mainly controlled by the chemical reaction, but in the case of shredded MSW it was mostly influenced by gas diffusion. The rate for the co-combustion of sludge pellets and combustible wastes was mainly determined by the combustion rate of the combustible waste. The activation energy of the 8-mm-diameter sludge pellets was between 6.70 and 10.0 kcal/mol, according to the moisture content, but it was lower for MSW and RDF. In the case of MSW co-combustion, the reaction rate accelerated as the moisture content of the sludge pellets decreased, but it was markedly increased by the addition of RDF, regardless of the sludge moisture content.     

The origins of municipal solid waste: The relations between residues from packaging materials and food

Data for the composition of municipal solid waste (MSW) from around the world are used to further examine a previously reported statistical correlation between the fraction of food residues and the fractions of paper and board, metal, glass and plastics residues in MSW. For data from many locations, these correlations are statistically significant; multiple linear regressions are computed. The fraction of food waste decreases as the fractions of waste from paper and board, metals and glass increase.The situation in the U.S.A. is examined further for just packaging waste. Similar correlations are established for the fraction of food residues and the fractions of paper and board and plastics packaging residues for predicted compositions for 1980 to 2000. Similar correlations for the U.K. are not statistically significant. Some reasons for this are postulated.The results of the statistical analyses predict that a strategy for decreasing the fraction of food waste in MSW is to increase the use of food packaging by some amount, especially plastics and metals, contrary to conventional wisdom.     

The future course of solid waste management in the U.S.

It is postulated that the current “garbage crisis” is due to a shortage of disposal capacity, not to burgeoning amounts of municipal solid waste (MSW). In support of this, trends in the quantity and composition of MSW, methods of waste reduction, recycling and growth of waste-to-energy capacity are examined to gain insight as to the future course of MSW management in the U.S. over about the next 15 plus years. This is the likely time to install new disposal capacity if pending legislative proposals are passed, that would enable states that provide their own disposal to ban wastes from other states.A new term, the “intensity of waste generation”, is proposed and illustrated, analogous to the intensity of mineral usage. The intensity is decreasing, implying that it is unlikely that waste generation will grow at rates projected by extrapolation or simple macroeconomic assumptions. Some other conclusions are: per capita MSW generation was nearly statistically constant from 1970 to 1984; the content of most forms of packaging in MSW are decreasing; packaging decreases the amount of food residues in MSW; and proposed national recycling targets of about 25% or more are not likely to be achieved, in part because of changes in the composition of MSW. Coupled with likely shortages of labor to process separated waste, it is forecast that there will be some future time when people will not think source separation is worth the bother and recycling will decrease. The future growth of waste-to-energy capacity is projected by assuming that a city will install capacity when others have done so, which leads to a simple quantitative model. The likely effects of impending landfill and incineration regulations are addressed.     

Municipal solid waste in Mostaganem city (Western Algeria)

The management of municipal solid waste (MSW) and valorisation is based on the understanding of MSW composition by its categories and physicochemical characteristics. In this study, we characterize and determine physicochemical parameters (density, fire loss, electric conductivity, average pH, moisture level, lower calorific value (LCV), total and organic carbon, and nitrogen) in order to establish MSW valorisation models for Mostaganem city (located in Western Algeria). The results show that organic matter represents 64.6% of waste, followed by paper-cardboard 15.9%, plastic 10.5%, glass 2.8%, textile 2.3%, metals 1.9%, and diverse materials 2%. These statistics are similar to results from developing countries, especially if organic matter, paper and plastic are taken into account, but differ from developed countries. This reflects the difference in lifestyle and consumption behaviour between the two communities. The parameters used to determine the possible valorisation model had the following average values: fire loss (63%); ash (37%); pH (6.1); electric conductivity (2.39 ms cm(-1)); total carbon (29.5%); nitrogen (1.5%); LCV (1028.6 kcal/kg), density (0.36), C/N (19.7) and moisture level (58.9%). The study shows that 31.1% of paper-cardboard, plastic, glass and metal wastes are recyclable. Incinerating MSW, with energy recovery, was a poor option because of the weak LCV (1028.6 kcal/kg). However, MSW produced a good methane yield of up to 1852.4 equivalent tons of oil per year. The agricultural benefits, C/N ratio values, levels of moisture and pH and the Tanner diagram all supported compost production.     

包装垃圾的分类与回收利用

包装垃圾是由废弃的包装物产生的固体垃圾,约占我国城市生活垃圾的1/3,虽然政府进行了必要回收,但仍有1/3以上的塑料、玻璃等包装物没能被有效回收利用,成了填埋场的主要填埋物,造成了环境污染和土地、石油等不可再生资源大量浪费。从回收利用和源头减量两方面提出包装垃圾的应对,一是对包装垃圾按来源、成分等进行详细分类,并建议回收处置方法;二是从制定行业政策方面来减少过度包装和扶持再生资源行业健康发展,有效处置包装垃圾等可再生资源。     

Rapid discrimination of plastic packaging materials using MIR spectroscopy coupled with independent components analysis (ICA)

Plastic packaging wastes increased considerably in recent decades, raising a major and serious public concern on political, economical and environmental levels. Dealing with this kind of problems is generally done by landfilling and energy recovery. However, these two methods are becoming more and more expensive, hazardous to the public health and the environment. Therefore, recycling is gaining worldwide consideration as a solution to decrease the growing volume of plastic packaging wastes and simultaneously reduce the consumption of oil required to produce virgin resin. Nevertheless, a major shortage is encountered in recycling which is related to the sorting of plastic wastes. In this paper, a feasibility study was performed in order to test the potential of an innovative approach combining mid infrared (MIR) spectroscopy with independent components analysis (ICA), as a simple and fast approach which could achieve high separation rates. This approach (MIR-ICA) gave 100% discrimination rates in the separation of all studied plastics: polyethylene terephthalate (PET), polyethylene (PE), polypropylene (PP), polystyrene (PS) and polylactide (PLA). In addition, some more specific discriminations were obtained separating plastic materials belonging to the same polymer family e.g. high density polyethylene (HDPE) from low density polyethylene (LDPE). High discrimination rates were obtained despite the heterogeneity among samples especially differences in colors, thicknesses and surface textures. The reproducibility of the proposed approach was also tested using two spectrometers with considerable differences in their sensitivities. Discrimination rates were not affected proving that the developed approach could be extrapolated to different spectrometers. MIR combined with ICA is a promising tool for plastic waste separation that can help improve performance in this field; however further technological improvements and developments are required before it can be applied at an industrial level given that all tests presented here were performed under laboratory conditions.     

Recycling of plastic packaging waste in Bandung City,Indonesia

Economic growth, changing consumption and production patterns are resulting in rapid increase in the generation of plastic wastes, including plastic packaging waste (PPW). A variety of PPW is identified in the municipal solid waste (MSW) stream. In this paper, quantity and composition of PPW at generators (residential and nonresidential sectors) and at the informal sector of waste recycling were measured, and accordingly the flow of PPW within Bandung City, Indonesia was analyzed. Though the generation rate per capita is not so high (25.1 g per day), total PPW generated by 2.3 million inhabitants in Bandung becomes 58.4 tonnes per day (3.76 % of total MSW generated). Due to lack of integrated MSW management, most of PPW is neither collected properly nor disposed of in appropriate manner by the municipality. Collection of valuable wastes including PPW is done predominantly by the informal sector without regard to health and safety. It is predicted that total PPW recycled by various informal waste recycling players like scavengers, junkmen, intermediates, and dealers is 27.5 tonnes per day (64.6 % of total PPW generated). Interviews regarding the existing handling methods and incentives preferred by generators to increase the recycling rate are also presented.     

The effect of storage and mechanical pretreatment on the biological stability of municipal solid wastes

Modern mechanical–biological waste treatment plants for the stabilization of both the source-separated organic fraction of municipal solid wastes (OFMSW) and the mixed stream of municipal solid wastes (MSW) include a mechanical pretreatment step to separate recyclable materials such as plastics, glass or metals, before biological treatment of the resulting organic material. In this work, the role of storage and mechanical pretreatment steps in the stabilization of organic matter has been studied by means of respiration techniques. Results have shown that a progressive stabilization of organic matter occurs during the pretreatment of the source-separated OFMSW, which is approximately 30% measured by the dynamic respiration index. In the case of mixed MSW, the stabilization occurring during the reception and storage of MSW is compensated by the effect of concentration of organic matter that the pretreatment step provokes on this material. Both results are crucial for the operation of the succeeding biological process. Finally, respiration indices have been shown to be suitable for the monitoring of the pretreatment steps in mechanical–biological waste treatment plants, with a strong positive correlation between the dynamic respiration index and the cumulative respiration index across all samples tested.     

The effect of moisture on air classification of municipal solid waste

The effect of moisture on the air classification of municipal solid waste (MSW) is analysed using a 2³ factorial design. A synthetic MSW is used in the laboratory to facilitate controlled variation of composition and moisture content. A pilot scale 120 ° zig-zag air classifier is used to perform the classification tests. Ten system response variables are evaluated including six recoveries, two purities and two efficiencies, to elucidate the impacts of (1) increased particle density resulting from moisture absorption and (2) particle adhesion. Results indicate a significant decrease in paper recovery and efficiency with increasing moisture. However, no significant reduction in aluminum and iron recovery is observed. This suggests that adhesion of these particles to extracted combustible materials is not a significant factor in reducing extract purity. Instead, extract purity reduction is a result of paper recovery losses from increasing particle density. The degree of moisture effect for varied MSW composition is greater for feeds with lower fractions of adsorbent materials. A redefination of percent moisture based on the MSW absorbent fraction is suggested in order to account for this varied impact. The new definition, moisture absorbancy ratio, is the weight of the moisture in the MSW divided by the dry weight of the absorbent materials in the MSW.     

Management of packaging waste in Poland--development agenda and accession to the EU.

In recent years the issue of the municipal waste in Poland has become increasingly topical, with a considerable rise in the waste generation, much of which can be attributed to a boom in product packaging (mainly plastic). The annual production of plastics packaging has been constantly increasing over the last 20 to 30 years, and now exceeds 3.7 million tons. Due to a lack of processing technologies and poorly developed selective segregation system, packaging waste is still treated as a part of the municipal solid waste (MSW) stream, most of which is landfilled. As a result of Poland's access to the European Union, previous legal regulations governing municipal waste management have been harmonized with those binding on the member countries. One of the main changes, the most revolutionary one, is to make entrepreneurs liable for environmental risks resulting from the introduction of packaging to the market, and for its recycling. In practice, all entrepreneurs are to ensure recovery, and recycling, of used packaging from products introduced to the market at the required level. In recent year, the required recycling levels were fulfilled for all types of materials but mainly by large institutions using grouped and transport packaging waste for that matter. Household packaging gathered in the selective segregation system at the municipalities was practically left alone. This paper is an attempt to describe the system and assess the first year of functioning of the new, revamped system of packaging waste management in Poland. Recommendations are made relating to those features that need to be included in packaging waste management systems in order to maximize their sustainability and harmonization with the EU legal system.     

Life cycle assessment for optimising the level of separated collection in integrated MSW management systems

This life cycle assessment study analyses material and energy recovery within integrated municipal solid waste (MSW) management systems, and, in particular, the recovery of the source-separated materials (packaging and organic waste) and the energy recovery from the residual waste. The recovery of materials and energy are analysed together, with the final aim to evaluate possible optimum levels of source-separated collection that lead to the most favourable energetic and environmental results; this method allows identification of an optimum configuration of the MSW management system. The results show that the optimum level of source-separated collection is about 60%, when all the materials are recovered with high efficiency; it decreases to about 50%, when the 60% level is reached as a result of a very high recovery efficiency for organic fractions at the expense of the packaging materials, or when this implies an appreciable reduction of the quality of collected materials. The optimum MSW management system is thus characterized by source-separated collection levels as included in the above indicated range, with subsequent recycling of the separated materials and energy recovery of the residual waste in a large-scale incinerator operating in combined heat and power mode.     

Municipal solid waste composition determination supporting the integrated solid waste management system in the island of Crete

A one-year survey was conducted in the greater region of Crete (located at the lower region of the Aegean Sea) for the purpose of identifying waste composition (including chemical and physical characterization), as well as any seasonal variation. The investigation was carried out repeatedly at seven landfills and one transfer station in Crete, in four phases. Each sampling phase corresponded to a season (autumn, winter, spring, summer). ASTM D5231-92(2003) standard method and RCRA Waste Sampling Draft Technical Guidance were used. Hand sorting was used for classifying the collected wastes into the following categories: plastics, paper, metals, aluminium, leather-wood-textiles-rubbers, organic wastes, non-combustibles and miscellaneous. Further analysis included proximate and ultimate analysis of combustible materials. Metals such as lead, cadmium and mercury were also investigated. The results show that there has been a significant decrease of organic wastes during the last decade due to the increase of packaging materials, as a result of a change in consumption patterns. Three main waste categories were determined: organic wastes, paper and plastics, which combined represent 76% of the total waste in Crete. Furthermore, a high fraction of glass and a seasonal variation of aluminium indicate a strong correlation of waste composition with certain human activities, such as tourism. There is also a variation between the municipal solid waste (MSW) composition in the region of Crete (2003-2004) and MSW composition suggested in the National Solid Waste Planning (2000) [National Solid Waste Planning, 2000. Completion and particularization of Common Ministerial Act 113944//1944/1997: National Solid Waste Planning, June 2000]. The results of this survey are to be utilized by the regional solid waste authorities in order to establish an integrated waste treatment site, capable of fulfilling the regional waste management demands.     

A flexible environmental reuse/recycle policy based on economic strength

Environmental policies based on fixed recycling rates may lead to increased environmental impacts (e.g., landfilled wastes) during economic expansion. A rate policy is proposed, which is adjusted according to the overall strength or weakness of the economy, as reflected by overall packaging demand and consumption, production and imports-exports. During economic expansion featuring rising consumption, production or exports, the proposed flexible policy suggests a higher reuse/recycle rate. During economic slowdown a lower rate results in lower impacts. The flexible target rates are determined in terms of annual data, including consumption, imports-exports and production. Higher environmental gains can be achieved at lower cost if the flexible policy is applied to widely consumed packaging products and materials associated with low rates, or if cleaner recycling technology is adopted.     

Recovery and recycling practices in municipal solid waste management in Lagos, Nigeria

The population of Lagos, the largest city in Nigeria, increased seven times from 1950 to 1980 with a current population of over 10 million inhabitants. The majority of the city's residents are poor. The residents make a heavy demand on resources and, at the same time, generate large quantities of solid waste. Approximately 4 million tonnes of municipal solid waste (MSW) is generated annually in the city, including approximately 0.5 million of untreated industrial waste. This is approximately 1.1 kg/cap/day. Efforts by the various waste management agencies set up by the state government to keep its streets and neighborhoods clean have achieved only minimal success. This is because more than half of these wastes are left uncollected from the streets and the various locations due to the inadequacy and inefficiency of the waste management system. Whilst the benefits of proper solid waste management (SWM), such as increased revenues for municipal bodies, higher productivity rate, improved sanitation standards and better health conditions, cannot be overemphasized, it is important that there is a reduction in the quantity of recoverable materials in residential and commercial waste streams to minimize the problem of MSW disposal. This paper examines the status of recovery and recycling in current waste management practice in Lagos, Nigeria. Existing recovery and recycling patterns, recovery and recycling technologies, approaches to materials recycling, and the types of materials recovered from MSW are reviewed. Based on these, strategies for improving recovery and recycling practices in the management of MSW in Lagos, Nigeria are suggested.     

Flow analysis of metals in a municipal solid waste management system

This study aimed to identify the metal flow in a municipal solid waste (MSW) management system. Outputs of a resource recovery facility, refuse derived fuel (RDF) production facility, carbonization facility, plastics liquefaction facility, composting facility, and bio-gasification facility were analyzed for metal content and leaching concentration. In terms of metal content, bulky and incombustible waste had the highest values. Char from a carbonization facility, which treats household waste, had a higher metal content than MSW incinerator bottom ash. A leaching test revealed that Cd and Pb in char and Pb in RDF production residue exceeded the Japanese regulatory criteria for landfilling, so special attention should be paid to final disposal of these substances. By multiplying metal content and the generation rate of outputs, the metal content of input waste to each facility was estimated. For most metals except Cr, the total contribution ratio of paper/textile/plastics, bulky waste, and incombustible waste was over 80%. Approximately 30% of Cr originated from plastic packaging. Finally, several MSW management scenarios showed that most metals are transferred to landfills and the leaching potential of metals to the environment is quite small.     

Municipal solid waste characteristics and management in Gümüşhane, Turkey

This paper presents a general overview of the current municipal solid waste (MSW) management in Gümüşhane Province, Turkey. In order to characterize the solid waste stream in the Municipality of Gümüşhane, a long-term study was conducted over a 52-week period between the spring of 2004 and the winter of 2005. In this study, percentage of components and specific weight of the MSW, the composting parameters (moisture content, total organic carbon, total nitrogen and pH), organic matter content, calorific value and the heavy metal concentrations (Cd, Cr, Cu, Ni, Pb, Zn, Fe, Mn, Co) of the compostable wastes sorted from the mixed MSW were determined and evaluated. In Gümüşhane, a mean of 70 tons of MSW are generated each day or 1 kg/day/capita. Approximately 4500 kg of the MSW were collected and sorted in a year, and the mean specific weight of these is 308 kg/m³. Approximately 30% of the MSW generated is compostable wastes and the yearly mean moisture content, organic matter content, C/N ratio and pH of these are 78%, 92.1%, 21.6/1 and 4.73, respectively, and approximately 24% of the MSW consists of recyclable materials. The recommended system deals with maximizing recycling and minimizing landfilling of the MSW, and consists of separation at source, collection, sorting, recycling, composting and sanitary landfilling. Heavy metal concentrations of the compostable wastes from the open dump were determined to decrease in the following order: Fe > Mn > Zn > Cr > Cu > Pb > Ni > Cd > Co.     

Solid waste recycling in Rajshahi city of Bangladesh

Efficient recycling of solid wastes is now a global concern for a sustainable and environmentally sound management. In this study, traditional recycling pattern of solid waste was investigated in Rajshahi municipality which is the fourth largest city of Bangladesh. A questionnaire survey had been carried out in various recycle shops during April 2010 to January 2011. There were 140 recycle shops and most of them were located in the vicinity of Stadium market in Rajshahi. About 1906 people were found to be involved in recycling activities of the city. The major fraction of recycled wastes were sent to capital city Dhaka for further manufacture of different new products. Only a small amount of wastes, specially plastics, were processed in local recycle factories to produce small washing pots and bottle caps. Everyday, an estimated 28.13 tons of recycled solid wastes were handled in Rajshahi city area. This recycled portion accounted for 8.25% of the daily total generated wastes (341 ton d^?1), 54.6% of total recyclable wastes (51.49 ton d^?1) and 68.29% of readily recyclable wastes (41.19 ton d^?1). Major recycled materials were found to be iron, glass, plastic, and papers. Only five factories were involved in preliminary processing of recyclable wastes. Collecting and processing secondary materials, manufacturing recycled-content products, and then buying recycled products created a circle or loop that ensured the overall success of recycling and generated a host of financial, environmental, and social returns.     

Facile characterization of polymer fractions from waste electrical and electronic equipment (WEEE) for mechanical recycling

In view of the environmental problem involved in the management of WEEE, and then in the recycling of post-consumer plastic of WEEE there is a pressing need for rapid measurement technologies for simple identification of the various commercial plastic materials and of the several contaminants, to improve the recycling of such wastes.This research is focused on the characterization and recycling of two types of plastics, namely plastic from personal computer (grey plastic) and plastic from television (black plastic). Various analytical techniques were used to monitor the compositions of WEEE. Initially, the chemical structure of each plastic material was identified by Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). Polymeric contaminants of these plastics, in particular brominated flame retardants (BFRs) were detected in grey plastics only using different techniques. These techniques are useful for a rapid, correct and economics identification of a large volumes of WEEE plastics.