Formation of indoor nitrous acid (HONO) by light-induced NO<Subscript>2</Subscript> heterogeneous reactions with white wall paint

Gaseous nitrogen dioxide (NO₂) represents an oxidant that is present in relatively high concentrations in various indoor settings. Remarkably increased NO₂ levels up to 1.5 ppm are associated with homes using gas stoves. The heterogeneous reactions of NO₂ with adsorbed water on surfaces lead to the generation of nitrous acid (HONO). Here, we present a HONO source induced by heterogeneous reactions of NO₂ with selected indoor paint surfaces in the presence of light (300 nm?<?λ?<?400 nm). We demonstrate that the formation of HONO is much more pronounced at elevated relative humidity. In the presence of light (5.5 W m^?2), an increase of HONO production rate of up to 8.6?·?10⁹ molecules cm^?2 s^?1 was observed at [NO₂]?=?60 ppb and 50 % relative humidity (RH). At higher light intensity of 10.6 (W m^?2), the HONO production rate increased to 2.1?·?10¹⁰ molecules cm^?2 s^?1. A high NO₂ to HONO conversion yield of up to 84 % was observed. This result strongly suggests that a light-driven process of indoor HONO production is operational. This work highlights the potential of paint surfaces to generate HONO within indoor environments by light-induced NO₂ heterogeneous reactions.     

Heterogeneous conversion of nitric acid to nitrous acid on the surface of primary organic aerosol in an urban atmosphere

Nitrous acid (HONO), nitric acid (HNO₃), and organic aerosol were measured simultaneously atop an 18-story tower in Houston, TX during August and September of 2006. HONO and HNO₃ were measured using a mist chamber/ion chromatographic technique, and aerosol size and chemical composition were determined using an Aerodyne quadrupole aerosol mass spectrometer. Observations indicate the potential for a new HONO formation pathway: heterogeneous conversion of HNO₃ on the surface of primary organic aerosol (POA). Significant HONO production was observed, with an average of 0.97 ppbv event^?1 and a maximum increase of 2.2 ppb in 4 h. Nine identified events showed clear HNO₃ depletion and well-correlated increases in both HONO concentration and POA-dominated aerosol surface area (SA). Linear regression analysis results in correlation coefficients (r²) of 0.82 for HONO/SA and 0.92 for HONO/HNO₃. After correction for established HONO formation pathways, molar increases in excess HONO (HONO_excess) and decreases in HNO₃ were nearly balanced, with an average HONO_excess/HNO₃ value of 0.97. Deviations from this mole balance indicate that the residual HNO₃ formed aerosol-phase nitrate. Aerosol mass spectral analysis suggests that the composition of POA could influence HONO production. Several previously identified aerosol-phase PAH compounds were enriched during events, suggesting their potential importance for heterogeneous HONO formation.     

Transformations,Lifetimes, and Sources of NO2, HONO,and HNO3 in Indoor Environments

Recent research has demonstrated that nitrogen oxides are transformed to nitrogen acids in indoor environments, and that significant concentrations of nitrous acid are present in indoor air. The purpose of the study reported in this paper has been to investigate the sources, chemical transformations and lifetimes of nitrogen oxides and nitrogen acids under the conditions existing in buildings. An unoccupied single family residence was instrumented for monitoring of NO, NO₂, NO_y, MONO, HNO₃, CO, temperature, relative humidity, and air exchange rate. For some experiments, NO₂ and HONO were injected into the house to determine their removal rates and lifetimes. Other experiments investigated the emissions and transformations of nitrogen species from unvented natural gas appliances. We determined that HONO is formed by both direct emissions from combustion processes and reaction of NO₂ with surfaces present indoors. Equilibrium considerations influence the relative contributions of these two sources to the indoor burden of HONO. We determined that the lifetimes of trace nitrogen species varied in the order NO ~ HONO > NO₂ >HNO₃. The lifetimes with respect to reactive processes are on the order of hours for NO and HONO, about an hour for NO₂, and 30 minutes or less for HNO3. The rapid removal of NO₂ and long lifetime of HONO suggest that HONO may represent a significant fraction of the oxidized nitrogen burden in indoor air.     

Measurements of primary trace gases and NOY composition in Houston,Texas

Concentrations of CO, SO₂, NO, NO₂, and NO_Y were measured atop the University of Houston's Moody Tower supersite during the 2006 TexAQS-II Radical and Aerosol Measurement Project (TRAMP). The lowest concentrations of all primary and secondary species were observed in clean marine air in southerly flow. SO₂ concentrations were usually low, but increased dramatically in sporadic midday plumes advected from sources in the Houston Ship Channel (HSC), located NE of the site. Concentrations of CO and NO_x displayed large diurnal variations in keeping with their co-emission by mobile sources in the Houston Metropolitan Area (HMA). CO/NO_x emission ratios of 5.81 ± 0.94 were observed in the morning rush hour. Nighttime concentrations of NO_x (NO_x = NO + NO₂) and NO_Y (NO_Y = NO + NO₂ + NO₃ + HNO₃ + HONO + 21N₂O₅ + HO₂NO₂ + PANs + RONO₂ + p-NO₃^? + …) were highest in winds from the NNW-NE due to emission from mobile sources. Median ratios of NO_x/NO_Y were approximately 0.9 overnight, reflecting the persistence and/or generation of NO_Z (NO_Z = NO_Y ? NO_x) species in the nighttime Houston boundary layer, and approached unity in the morning rush hour. Daytime concentrations of NO_x and NO_Y were highest in winds from the HSC. NO_x/NO_Y ratios reached their minimum values (median ca 0.63) from 1300 to 1500 CST, near local solar noon, and air masses often retained enough NO_x to sustain additional O₃ formation farther downwind. HNO₃ and PANs comprised the dominant NO_Z species in the HMA, and on a median basis represented 17–20% and 12–15% of NO_Y, respectively, at midday. Concentrations of HNO₃, PANs, and NO_Z, and fractional contributions of these species to NO_Y, were at a maximum in NE flow, reflecting the source strength and reactivity of precursor emissions in the HSC. As a result, daytime O₃ concentrations were highest in air masses with HSC influence. Overall, our findings confirm the impact of the HSC as a dominant source region within the HMA. A comparison of total NO_Y measurements with the sum of measured NO_Y species (NO_Yi = NO_x + HNO₃ + PANs + HONO + p-NO₃^?) yielded excellent overall agreement during both day ([NO_Y](ppb) = ([NO_Yi](ppb)11.03 ± 0.16) ? 0.42; r² = 0.9933) and night ([NO_Y](ppb) = ([NO_Yi](ppb)11.01 ± 0.16) + 0.18; r² = 0.9975). A similar comparison between NO_Y–NO_x concentrations and the sum of NO_Zi (NO_Zi = HNO₃ + PANs + HONO + p-NO₃^?) yielded good overall agreement during the day ([NO_Z](ppb) = ([NO_Zi](ppb)11.01 ± 0.30) + 0.044 ppb; r² = 0.8527) and at night ([NO_Z](ppb) = ([NO_Zi](ppb)11.12 ± 0.69) + 0.16 ppb; r² = 0.6899). Median ratios of NO_Z/NO_Zi were near unity during daylight hours but increased to approximately 1.2 overnight, a difference of 0.15–0.50 ppb. Differences between NO_Z and NO_Zi rarely exceeded combined measurement uncertainties, and variations in NO_Z/NO_Zi ratios may have resulted solely from errors in conversion efficiencies of NO_Y species and changes in NO_Y composition. However, nighttime NO_Z/NO_Zi ratios and the magnitude of NO_Z ? NO_Zi differences were generally consistent with recent observations of ClNO₂ in the nocturnal Houston boundary layer.     

Investigations of emissions and heterogeneous formation of HONO in a road traffic tunnel

Simultaneous measurements of nitrous acid (HONO) and nitrogen dioxide (NO₂) using a differential optical absorption spectroscopy system, nitrogen oxide (NO) by an in situ chemiluminescence analyser and carbon dioxide (CO₂) by a gas chromatographic technique were carried out in the Wuppertal Kiesbergtunnel. At high traffic density HONO concentrations of up to 45 ppbV were observed. However, at low traffic density unexpectedly high HONO concentrations of up to 10 ppbV were measured caused by heterogeneous HONO formation on the tunnel walls. In addition to the tunnel campaigns, emission measurements of HONO, NO₂, NO and CO₂ from different single vehicles (a truck, a diesel and a gasoline passenger car) were also performed. For the correction of the HONO emission data, the heterogeneous HONO formation on the tunnel walls was quantified by two different approaches (a) in different NO₂ emission experiments in the tunnel without traffic and (b) on tunnel wall residue in the laboratory. The HONO concentration corrected for heterogeneous formation on the tunnel walls, in relation to the CO₂ concentration can be used to estimate the amount of HONO, which is directly emitted from the vehicle fleet. From the measured data, emission ratios (e.g. HONO/NO_x) and emission indices (e.g. mg HONO kg⁻¹ fuel) were calculated. The calculated emission index of 88±18 mg HONO kg⁻¹ fuel allows an estimation of the HONO emission rates from traffic into the atmosphere. Furthermore, the heterogeneous formation of HONO from NO₂ on freshly emitted exhaust particles is discussed.     

Positive interference of nitrous acid in the determination of gaseous HNO3 by the NOx chemiluminescence-nylon cartridge method: Applications to measurements of ppb levels of HONO in air

Gaseous nitrous acid in air has been simultaneously monitored in environmental chambers by an absolute method, differential optical absorption spectroscopy, and by a nylon cartridge-chemiluminescence NO_x technique originally developed by Spicer and co-workers for gaseous HNO₃. In the absence of HNO₃, the latter technique proved to be a simple and accurate method for measuring ppb levels of HONO in air. However, the positive interference by HONO in the nylon cartridge-chemiluminescence technique may have important ramifications due to possible artifacts in measurements of gaseous HNO₃ by removal on nylon surfaces. Thus, previous observations in night-time atmospheres or environmental chambers attributed entirely to gaseous HNO₃ may have been, at least in part, due to the presence of gaseous HONO.     

Antifungal efficiency assessment of the TiO2 coating on façade paints

The work studies the photocatalytic activity and the antifungal efficiency of the TiO₂/Zn-Al coatings placed on the target commercial façade paints. The photocatalytic active nanocomposite based on TiO₂ and Zn-Al-layered double hydroxides (ZnAl-LDHs) was synthesized by a wet impregnation technique with 3 % w/w TiO₂. The freshly prepared suspension was applied by spray technique on the surfaces of the white façade paints. The goal of the work was to develop a method that quickly quantifies the antifungal activity of the commercial façade paints with and without biocidal components covered with a photocatalytic coating. The essence of the proposed method is the monitoring of the fungal growth (artificial ageing conditions) and the quantification of its development (UV-A 0.13 mWcm^?2) on the façade paint surfaces. A special fungus nutrient (potato dextrose agar (PDA)) was inoculated with the spores of the Aspergillus niger ATCC 6275, and the test samples (façade paints with and without photocatalytic coating) were placed on the inoculated nutrient in the petri dishes. The images of the fungal growth on the samples of the facade paints, during a period of 5 days, were imported into Matlab R2012a where they were converted to binary images (BW), based on the adequate threshold. The percentage of the surface coverage was calculated by applying the specifically written program code which determines the ratio of the black and white pixels. The black pixels correspond to the surface covered with hyphae and mycelia of the fungus.     

Heterogeneous reaction of NO2 with soot at different relative humidity

The influences of relative humidity (RH) on the heterogeneous reaction of NO₂ with soot were investigated by a coated wall flow tube reactor at ambient pressure. The initial uptake coefficient (γ _initial) of NO₂ showed a significant decrease with increasing RH from 7 to 70%. The γ _initial on “fuel-rich” and “fuel-lean” soot at RH = 7% was (2.59 ± 0.20) × 10^?5 and (5.92 ± 0.34) × 10^?6, respectively, and it decreased to (5.49 ± 0.83) × 10^?6 and (7.16 ± 0.73) × 10^?7 at RH = 70%, respectively. Nevertheless, the HONO yields were almost independent of RH, with average values of (72 ± 3)% for the fuel-rich soot and (60 ± 2)% for the fuel-lean soot. The Langmuir-Hinshelwood mechanism was used to demonstrate the negative role of RH in the heterogeneous uptake of NO₂ on soot. The species containing nitrogen formed on soot can undergo hydrolysis to produce carboxylic species or alcohols at high RH, accompanied by the release of little gas-phase HONO and NO.

     

Use of carbon-based composites to enhance performance of TiO<Subscript>2</Subscript> for the simultaneous removal of nitrates and organics from aqueous environments

The simultaneous photocatalytic removal of nitrate from aqueous environment in presence of organic hole scavenger using TiO₂ has long been explored. However, the use of unmodified TiO₂ in such reaction resulted in non-performance or release of significant amount of undesirable reaction products in the process, a problem that triggered surface modification of TiO₂ for enhanced photocatalytic performance. Previous studies focused on decreasing rate of charge carrier recombination and absorption of light in the visible region. Yet, increasing active sites and adsorption capacity by combining TiO₂ with a high surface area adsorbent such as activated carbon (AC) remains unexploited. This study reports the potential of such modification in simultaneous removal of nitrates and oxalic acid in aqueous environment. The adsorptive behaviour of nitrate and oxalic acid on TiO₂ and TiO₂/AC composites were studied. The Langmuir adsorption coefficient for nitrate was four times greater than that of oxalic acid. However, the amount of oxalic acid adsorbed was about 10 times greater than the amount of nitrate taken up. Despite this advantage, the materials did not appear to produce more active photocatalysts for the simultaneous degradation of nitrate and oxalic acid. The photocatalytic activity of TiO₂ and its carbon-based composites was improved by combination with Cu₂O particles. Consequently, 2.5 Cu₂O/TiO₂ exhibited the maximum photocatalytic performance with 57.6 and 99.8% removal of nitrate and oxalic acid, respectively, while selectivity stood at 45.7, 12.4 and 41.9% for NH₄⁺, NO₂^? and N₂, respectively. For the carbon based, 2.5 Cu₂O/TiO₂-20AC showed removal of 12.7% nitrate and 80.3% oxalic acid and achieved 21.6, 0 and 78.4% selectivity for NH₄⁺, NO₂^? and N₂, respectively. Using the optimal AC loading (20 wt%) resulted in significant decrease in the selectivity for NH₄⁺ with no formation of NO₂^?, which unveils that selectivity for N₂ and low/no selectivity for undesirable products can be manipulated by controlling the rate of consumption of oxalic acid. In contract, no nitrate reduction was observed with Cu₂O promoted TiO₂-T and its TiO₂-(T)-20AC, which may be connected to amorphous nature of TiO₂-T and perhaps served as charge carrier trapping sites that impeded activity.     

An observational study of the HONO–NO2 coupling at an urban site in Guangzhou City,South China

The temporal behavior of HONO and NO₂ was investigated at an urban site in Guangzhou city, China, by means of a DOAS system during the Pearl River Delta 2006 intensive campaign from 10 to 24 July 2006. Within the whole measurement period, unexpected high HONO mixing ratios up to 2 ppb were observed even during the day. A nocturnal maximum concentration of about 8.43 ± 0.4 ppb was detected on the night of 24 July 2006. Combining the data simultaneously observed by different instruments, the coupling of HONO–NO₂ and the possible formation sources of HONO are discussed. During the measurement period, concentration ratios of HONO to NO₂ ranged from (0.03 ± 0.1) to (0.37 ± 0.09), which is significantly higher than previously reported values (0.01–0.1). Surprisingly, in most cases a strong daytime correlation between HONO and NO₂ was found, contrary to previous observations in China. Aerosol was found to have a minor impact on HONO formation during the whole measurement period. Using a pseudo steady state approach for interpreting the nocturnal conversion of NO₂ to HONO suggests a non-negligible role of the relative humidity for the heterogeneous HONO formation from NO₂.     

Atmospheric concentrations of ammonia and ammonium at an agricultural site in the southeast United States

In this study, we present ∼1 yr (October 1998–September 1999) of 12-hour mean ammonia (NH₃), ammonium (NH₄⁺), hydrochloric acid (HCl), chloride (Cl⁻), nitrate (NO₃⁻), nitric acid (HNO₃), nitrous acid (HONO), sulfate (SO₄²⁻), and sulfur dioxide (SO₂) concentrations measured at an agricultural site in North Carolina's Coastal Plain region. Mean gas concentrations were 0.46, 1.21, 0.54, 5.55, and 4.15 μg m⁻³ for HCl, HNO₃, HONO, NH₃, and SO₂, respectively. Mean aerosol concentrations were 1.44, 1.23, 0.08, and 3.37 μg m⁻³ for NH₄⁺, NO₃⁻, Cl⁻, and SO₄²⁻, respectively. Ammonia, NH₄⁺, HNO₃, and SO₄²⁻ exhibit higher concentrations during the summer, while higher SO₂ concentrations occur during winter. A meteorology-based multivariate regression model using temperature, wind speed, and wind direction explains 76% of the variation in 12-hour mean NH₃ concentrations (n=601). Ammonia concentration increases exponentially with temperature, which explains the majority of variation (54%) in 12-hour mean NH₃ concentrations. Dependence of NH₃ concentration on wind direction suggests a local source influence. Ammonia accounts for >70% of NH_x (NH_x=NH₃+NH₄⁺) during all seasons. Ammonium nitrate and sulfate aerosol formation does not appear to be NH₃ limited. Sulfate is primarily associated ammonium sulfate, rather than bisulfate, except during the winter when the ratio of NO₃⁻–NH₄⁺ is ∼0.66. The annual average NO₃⁻–NH₄⁺ ratio is ∼0.25.     

A new measurement method for nitrogen oxides in the air using an annular diffusion scrubber coated with titanium dioxide

A new convenient measurement method of nitrogen oxides (NO_x) in the ambient air was developed. The collection of NO_x is performed by an annular diffusion scrubber coated with a mixture of titanium dioxide (TiO₂) and hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂) and the analysis is carried out by ion chromatography with conductivity detection. Under ultraviolet light (UV) illumination, TiO₂ produces reactive oxygen species such as super oxide (O₂⁻), hydroxyl radical (OH·) and peroxyhydroxyl radical (HO₂·), by which nitric oxide (NO) is oxidized to nitrogen dioxide (NO₂), and is further oxidized to nitric acid (HNO₃). The yielded HNO₃ and NO₂ are effectively adsorbed on the surface of TiO₂ and hydroxyapatite. The collection efficiencies of NO and NO₂ by the annular diffusion scrubber coated with the catalysts under UV illumination are higher than 98%, respectively, at the air flow rate of 0.2–1.0 l min⁻¹. After the collection of NO_x, by feeding deionized water into the annular diffusion scrubber, HNO₃ and NO₂ which adsorbed on the catalysts are extracted as forms of nitrite ion (NO₂⁻) and nitrate ion (NO₃⁻). The extraction efficiencies of NO and NO₂ are almost 100%. The activity of the washed catalysts can be completely recovered by drying with the purified air. Further, a simultaneous separated measurement of NO and NO₂ can be performed by utilizing the UV illumination dependence. This method was applied to the measurement of NO_x in the ambient air. The NO_x concentration measured by this method was in good agreement with that obtained using the chemiluminescence NO_x analyzer.     

NOy speciation with a combined wet effluent diffusion denuder – aerosol collector coupled to ion chromatography

A wet effluent denuder - aerosol collector (WEDD/AC) system coupled to ion chromatography for the measurement of atmospheric HONO, HNO₃ and particulate nitrite, nitrate and sulfate is described. Several experiments were performed to outline its performance. The main features are low detection limits and a fast response to concentration changes which enables measurements with high time resolution. In contrast to highly soluble gases, the collection efficiency of less soluble gases is shown to depend on the Henry’s law constant rather than on the uptake kinetics. To improve the collection efficiency for HONO under simultaneous presence of acidifying gases, NaHCO₃ was added to the effluent solution. The system was tested in a field campaign in the suburban area of Zürich, Switzerland. Elevated concentrations of nitrous acid up to 3.2 ppb were detected during the measurement campaign. The diurnal variation of the HONO to NO₂ ratio clearly points to a fast and persistent process producing HONO in the atmosphere. The correlation with NO_x and black carbon suggests a heterogeneous formation of HONO, and is consistent with a reaction on soot aerosol particle surfaces postulated from previous laboratory results.     

Simultaneous DOAS and mist-chamber IC measurements of HONO in Houston,TX

Nitrous acid is an important component of nighttime N-oxide chemistry, and provides a significant source of both OH and NO in polluted urban air masses shortly after sunrise. Several recent studies have called for new sources of HONO to account for daytime levels much higher than are consistent with current understanding. However, measurement of HONO is problematic, with most in-situ techniques reporting higher values than simultaneous optical measurements by long-path DOAS, especially during daytime. The discrepancy has been attributed to positive interference in the in-situ techniques, negative interference in DOAS retrievals, the difficulty of comparing the different air masses sampled by the methods, or combinations of these.During August and September 2006, HONO mixing ratios from collocated long-path DOAS and automated mist-chamber/ion chromatograph (MC/IC) systems ranged from several ppbv during morning rush hour to daytime minima near 100 pptv. Agreement between the two techniques was excellent across this entire range during many days, showing that both instruments accurately measured HONO during this campaign. A small bias towards higher LP-DOAS observations at night can be attributed to slow vertical mixing leading to pronounced HONO profiles. A positive daytime bias of the MC/IC instrument during several days in late August/early September was correlated with photochemically produced compounds such as ozone, HNO₃ and HCHO, but not with NO₂, NO_x, HO₂NO₂, or the NO₂ photolysis rate. While an interferant could not be identified organic nitrites appear a possible explanation for our observations.     

Possible particulate nitrite formation and its atmospheric implications inferred from the observations in Seoul,Korea

Simultaneous measurements of gaseous species and fine-mode, particulate inorganic components were performed at the University of Seoul, Seoul in Korea. In the simultaneous measurements, a certain level of nitrous acid (HONO) was observed in the gas-phase, indicating possible heterogeneous HONO production on the surface of the ambient aerosols. On the other hand, high particulate nitrite (NO^2?) concentrations of 1.41(±2.26) μg/m³ were also measured, which sometimes reached 18.54 μg/m³. In contrast, low HONO-to-NO₂ ratios of 0.007(±0.006) were observed in Seoul. This indicates that a significant fraction of HONO is dissolved in atmospheric aerosols. Around the Seoul site, sufficient alkalinity may have been provided to the atmospheric aerosols from the excessive presence of NH₃ in the gas-phase. Due to the alkaline particulate conditions (defined in this study as a particle pH >～3.29), the HONO molecules produced at the surface of the atmospheric aerosols appeared to have been converted into particulate nitrite, thereby preventing their further participation in the atmospheric O₃/NO_y/HO_x photochemical cycles. It was estimated that a minimum average of 65% of HONO was captured by alkaline, anthropogenic, urban particles in the Seoul measurements.     

Measurements of atmospheric nitrous acid and nitric acid

A highly sensitive technique for the measurement of atmospheric HONO and HNO₃ is reported. The technique is based on aqueous scrubbing using two coil samplers, followed by conversion of HNO₃ to nitrite, derivatization of nitrite to a highly light-absorbing azo dye with sulfanilamide (SA) and N-(1-naphthyl) ethylenediamine (NED), and high performance liquid chromatography (HPLC) analysis. HNO₃ concentration was obtained by the difference of the two channels. Two scrubbing solutions were used for sampling the two species: a 1-mM phosphate buffer solution (pH 7) for the measurement of HONO and a 180 mM NH₄Cl/NH₃ buffer solution (pH 8.5) for the measurement of HONO+HNO₃. The scrubbing solution flow rate was 0.24 ml min⁻¹ and the gas sampling flow rate was 2 l min⁻¹. HNO₃ in the NH₄Cl/NH₃ buffer solution was quantitatively reduced to nitrite along an on-line 0.8-cm Cd reductor column. Nitrite in both channels was derivatized with 2 mM SA and 0.2 mM NED in 25 mM HCl. Quantitative derivatization was achieved within 5 min at 55°C. The azo dye derivative was then separated from the SA/NED reagent by reversed-phase HPLC and detected with a UV-vis detector at 540 nm. With an on-line SEP-PAK C-18 cartridge for the reagent purification, the method detection limit is estimated to be better than 1 pptv for HONO and about 20 pptv for HNO₃. The sample integration time was about 2 min and the sampling frequency is every 10 min. Data collected in downtown Albany and Whiteface Mountain, NY, are shown as examples of applications of this technique in both urban and remote clean environments.     

Potential interferences in photolytic nitrogen dioxide converters for ambient air monitoring: Evaluation of a prototype

ABSTRACT

Mixing ratios of the criteria air contaminant nitrogen dioxide (NO₂) are commonly quantified by reduction to nitric oxide (NO) using a photolytic converter followed by NO-O₃ chemiluminescence (CL). In this work, the performance of a photolytic NO₂ converter prototype originally designed for continuous emission monitoring and emitting light at 395 nm was evaluated. Mixing ratios of NO₂ and NO_x (= NO + NO₂) entering and exiting the converter were monitored by blue diode laser cavity ring-down spectroscopy (CRDS). The NO₂ photolysis frequency was determined by measuring the rate of conversion to NO as a function of converter residence time and found to be 4.2 s^?1. A maximum 96% conversion of NO₂ to NO over a large dynamic range was achieved at a residence time of (1.5 ± 0.3) s, independent of relative humidity. Interferences from odd nitrogen (NO_y) species such as peroxyacyl nitrates (PAN; RC(O)O₂NO₂), alkyl nitrates (AN; RONO₂), nitrous acid (HONO), and nitric acid (HNO₃) were evaluated by operating the prototype converter outside its optimum operating range (i.e., at higher pressure and longer residence time) for easier quantification of interferences. Four mechanisms that generate artifacts and interferences were identified as follows: direct photolysis, foremost of HONO at a rate constant of 6% that of NO₂; thermal decomposition, primarily of PAN; surface promoted photochemistry; and secondary chemistry in the connecting tubing. These interferences are likely present to a certain degree in all photolytic converters currently in use but are rarely evaluated or reported. Recommendations for improved performance of photolytic converters include operating at lower cell pressure and higher flow rates, thermal management that ideally results in a match of photolysis cell temperature with ambient conditions, and minimization of connecting tubing length. When properly implemented, these interferences can be made negligibly small when measuring NO₂ in ambient air.

Implications: A new near-UV photolytic converter for measurement of the criteria pollutant nitrogen dioxide (NO₂) in ambient air by CL was characterized. Four mechanisms that generate interferences were identified and investigated experimentally: direct photolysis of HONO which occurred at a rate constant 6% that of NO₂, thermal decomposition of PAN and N₂O₅, surface promoted chemistry involving HNO₃, and secondary chemistry involving NO in the tubing connecting the converter and CL analyzer. These interferences are predicted to occur in all NO₂ P-CL systems but can be avoided by appropriate thermal management and operating at high flow rates.     

Deposition and adsorption of the air pollutant HNO3 vapor to soil surfaces

Deposition of nitric acid (HNO₃) vapor to soils has been evaluated in three experimental settings: (1) continuously stirred tank reactors with the pollutant added to clean air, (2) open-top chambers at high ambient levels of pollution with and without filtration reducing particulate nitrate levels, (3) two field sites with high or low pollution loads in the coastal sage plant community of southern California. The results from experiment (1) indicated that the amount of extractable NO₃⁻ from isolated sand, silt and clay fractions increased with atmospheric concentration and duration of exposure. After 32 days, the highest absorption of HNO₃ was determined for clay, followed by silt and sand. While the sand and silt fractions showed a tendency to saturate, the clay samples did not after 32 days of exposure under highly polluted conditions. Absorption of HNO₃ occurred mainly in the top 1 mm layer of the soil samples and the presence of water increased HNO₃ absorption by about 2-fold. Experiment (2) indicated that the presence of coarse particulate NO₃⁻ could effectively block absorption sites of soils for HNO₃ vapor. Experiment (3) showed that soil samples collected from open sites had about 2.5 more extractable NO₃⁻ as compared to samples collected from beneath shrub canopies. The difference in NO₃⁻ occurred only in the upper 1–2 cm as no significant differences in NO₃⁻ concentrations were found in the 2–5 cm soil layers. Extractable NO₃⁻ from surface soils collected from a low-pollution site ranged between 1 and 8 μg NO₃–N g⁻¹, compared to a maximum of 42 μg NO₃–N g⁻¹ for soils collected from a highly polluted site. Highly significant relationship between HNO₃ vapor doses and its accumulation in the upper layers of soils indicates that carefully prepared soil samples (especially clay fraction) may be useful as passive samplers for evaluation of ambient concentrations of HNO₃ vapor.     

Uptake of nitrous acid and nitrogen oxides by nylon surfaces: Implications for nitric acid measurement

The interference in HNO₃ determination due to HNO₂ and NO_x retention on nylon filters has been evaluated in laboratory and field conditions. Nitrous acid is retained on nylon filters with efficiencies varying from 25% at 12ℓ min⁻¹ to 80% at 2ℓ min⁻¹, yielding NO₂⁻ ion. In ambient sampling performed during photochemical smog episodes, NO₂⁻ is oxidized to NO₃⁻ with conversion factors up to 100%, resulting in a positive bias in HNO₃ determination.NO₂ reacts heterogeneously with H₂O on nylon surfaces according to the reaction 2NO₂ + H₂O → HNO₂ + HNO₃ with a removal constant of about 1 × 10⁻⁴ ms⁻¹ at a H₂O concentration of 20,000 ppm. The resulting nitrite and nitrate are independent of the sampling flow rate, while NO₂ concentration, sampling time and exposed nylon surface area play a directly proportional role. Accordingly, the relative interference of NO₂ with respect to HNO₃ determination is almost negligible for nylon filters, usually run at relatively high flow rates, while it may be significant for nylon denuders, which are characterized by larger exposed surfaces and lower operating flow rates.     

Impacts of a strong cold front on concentrations of HONO,HCHO, O3, and NO2 in the heavy traffic urban area of Beijing

Much rain and strong winds caused by a cold front occurred in Beijing during the period of Sep. 27 to Oct. 4, 2004 and led to sharp drops in maximum and mean concentrations of HONO, HCHO, O₃, and NO₂, i.e., the maximum concentrations were reduced by 5.9, 21.3, 45.6, and 44.4 ppb, respectively, and the mean concentrations were decreased by 4.0, 5.5, 30.3, and 32.3 ppb, respectively. For daily HO_x production rates HONO photolysis was the largest contributor and over 90% contributions were from photolysis of HONO and HCHO. Large number and area percentages of soot aggregate from PM10, and high correlations between concentrations of PM10 and chemical formation of HONO suggested that heterogeneous reactions of NO₂ on surfaces of soot aggregate could be a key source of HONO in the heavy traffic areas of Beijing during the night and should be considered in air quality simulations for such areas.