Determination of the levels of aromatic amines in indoor and outdoor air in Italy

We studied the concentration of 10 primary aromatic amines (AA), which are classified as suspected carcinogens, in indoor and outdoor air in Italy. The measured AA included: aniline, o-toluidine, m-toluidine, p-toluidine, 2,3-dimethylaniline, 2,4-dimethylaniline, 2,5-dimethylaniline, 2,6-dimethylaniline, 2-naphtylamine and 4-aminobiphenyl. In the indoor environment (homes, offices and public buildings) the level of contamination (expressed as sum of 9 AA, excluding aniline) varied from 3 ng/m3 (hospital ward) to 207 ng/m3 (discotheque). In most indoor environments with no contamination from cigarette smoke the AA levels were below 20 ng/m3, whereas in the presence of smokers higher values were observed. Aniline levels were more erratic (varying from 53 ng/m3 (office of non-smokers) to 1929 ng/m3 (discotheque) and were not related to cigarette smoke. The concentration range of AA (excluding aniline) in the outside air varied from 3 ng/m3 (Siena) to 104 ng/m3 (Brindisi); aniline concentration was extremely variable. Most samples of outdoor air had AA levels lower than 40 ng/m3. In conclusion, AA are widespread air contaminants and attain a high concentration in heavily contaminated indoor environments, due to smoking and poor ventilation. AA occasionally attain a high level in outdoor air as well. Therefore, a strategy of reduction of the exposure to AA should consider the abatement of multiple sources of contamination.     

A methodology for the estimation of road transport air emissions in urban areas of Italy

This paper focuses on the top–down approach for estimating road transport emissions at a local level. A bottom–up approach is preferable where the data and information required by estimation methodologies are available at regional territorial level. In the absence of this regional data, emissions are adapted from national to smaller levels by means of proxy variables. This study highlights the importance of an improvement of the top–down methodology and identifies a corrective index to better characterise road transport emissions at a local level. A set of indicators related to transport activities is selected in order to identify homogeneous areas in the Italian territory. For each area, COPERT (Computer Programme to estimate Emissions from Road Traffic) methodology is applied to estimate the atmospheric emissions of different pollutants; the same methodology is used to calculate road transport emissions at a national level. The results, calculated according to vehicle category and driving mode, are compared with those deriving from a spatial disaggregation of national data by means of simple surrogate variables.     

Polycyclic aromatic hydrocarbons air levels in Florence,Italy, and their correlation with other air pollutants

Benzo(a)pyrene [B(a)P] air levels were measured in Florence (Italy) in the period 1992-2001. For the period 1999-2000 seven polycyclic aromatic hydrocarbons (PAH) (benzo(a)anthracene, crysene, benzo(a)pyrene (B(a)P), benzo(b)fluoranthene (B(b)F), benzo(k)fluoranthene, dibenzo(a,h)anthracene (DBA) and benzo(g,h,i)perylene (BGP)), were measured in the air in four different sites (one with heavy traffic (A), one in a park (B), one in a residential area (C) and one in a hill area (D)). B(a)P levels were elevated in 1992-1998 (maximum average value of winter months: 5.8 ng/ m3) but a decreasing trend was observed in the following years, probably due to improvement in vehicle emissions. The sum of PAH in the air in the period 1999-2000 was about one order of magnitude lower in the hill site (D) relative to the urban sites, and residential areas (B and C) had values 2.5-3 times lower compared to site A with a heavy traffic. PAH concentrations decreased in the warmer seasons of 2000 in all sites. A negative correlation was found between PAH levels and ozone. A positive correlation with carbon monoxide (CO) (r = 0.862, P < 0.001) and low B(a)P/BGP ratios, ranging from 0.44 to 0.51, indicated that vehicular traffic was the major PAH source in all monitored sites. Using B(a)P(TEF) values (toxic equivalency factors) for evaluating the biological activity of PAH, we found that the highest PAH contributors in terms of potential air carcinogenic activity were B(a)P and DBA. Therefore, in addition to B(a)P, DBA concentration should be considered in the evaluation of air quality in terms of PAH contamination.     

Biodiversity of epiphytic lichens and air pollution in the town of Siena (central Italy).

The results of a biomonitoring survey carried out in the town of Siena (central Italy) using the biodiversity of epiphytic lichens as indicator of air pollution are reported. The general picture was rather good, with more than 60% of the study area being in the categories "semi-natural" or "natural" according to a calibrated scale of environmental naturality/alteration. Compared with the situation of 1995, ameliorating conditions were found as a result of an improvement in air quality over time.     

The sensitivity of the CHIMERE model to emissions reduction scenarios on air quality in Northern Italy

The sensitivity of the CHIMERE model to emission reduction scenarios on particulate matter PM2.5 and ozone (O₃) in Northern Italy is studied. The emissions of NO_x, PM2.5 SO₂, VOC or NH₃ were reduced by 50% for different source sectors for the Lombardy region, together with 5 additional scenarios to estimate the effect of local measures on improving the air quality for the Po valley area. Firstly, we evaluate the model performance by comparing calculated surface aerosol concentrations for the standard case (no emission reductions) with observations for January and June 2005. Calculated monthly mean PM10 concentrations are in general underestimated. For June, modelled PM10 concentrations slightly overestimate the measurements. Calculated monthly mean SO₄, NO₃^?, NH₄⁺ concentrations are in good agreement with the observations for January and June. Secondly, the model sensitivity of emission reduction scenarios on PM2.5 and O₃ calculated concentrations for the Po valley area is evaluated. The most effective scenarios to abate PM2.5 concentration are based on the SNAP2 (non-industrial combustion plants) and SNAP7 (road traffic) sectors, for which the NO_x and PM2.5 emissions are reduced by 50%. The number of days that the 2015 PM2.5 limit value of 25 μg m^?3 in Milan is exceeded by reducing primary PM2.5 and NO_x emissions for SNAP2 and 7 by 50%, does not change in January when compared to the standard case for the Milan area. It appears that 40% of the PM2.5 concentration in the greater Milan area is caused by the emissions surrounding the Lombardy region and from the model boundary conditions.This study also showed that a more effective pollutant reduction (emissions) per ton of pollutant reduced (concentrations) for the greater Milan area is obtained by reducing the primary PM2.5 emissions for SNAP7 by 50%. The most effective scenario on PM2.5 decrease for which precursor emissions are reduced is achieved by reducing SO₂ emissions by 50% for SNAP7.Our study showed that during summer time, the largest reductions in O₃ concentrations are achieved for SNAP7 emission reductions, when volatile organic compounds (VOCs) are reduced by 50%.     

Estimates of the economic damage due to the soiling of residential buildings induced by air pollution in Italy

Environmental Science and Pollution Research - The soiling of the external façades of buildings caused by air pollution has economic costs that are generally not borne entirely by the...     

Leaves of Quercus ilex L. as biomonitors of PAHs in the air of Naples (Italy)

Polycyclic aromatic hydrocarbons (PAHs) were determined by the GC-MS chromatography in the leaves of Quercus ilex L., an evergreen Mediterranean oak, to monitor the degree of pollution in the urban area of Naples compared to remote areas. Leaf samples were collected in July 1998 from four urban parks, six roadsides and two sites in remote areas. The total PAH contents in Q. ilex leaves ranged from 106.6 in a control site to 4607.5 ng/g d.w. along a road with a high traffic flow. The mean concentration factors (urban/control) were 3.8 for the parks and 15 for the roads. The contribution of carcinogenic PAHs (benz[a]anthracene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, indeno[1,2,3-c,d]pyrene) was higher in urban area and differed according to the site, ranging from 6.7% to 21.3%. The total PAH burden in control sites was dominated by the low molecular weight PAHs, whilst along the urban roads fluoranthene, pyrene and benz[a]anthracene among the measured PAHs showed the highest values. PAHs were positively correlated (P<0.01) to trace metals measured in a previous study.     

The role of a steel plant in north-west Italy to the local air concentrations of PCDD/Fs

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are ubiquitous contaminants, mainly released into the environment during combustion processes (point sources), but also from other sources (traffic, uncontrolled combustion).This study aims at investigating the contribution of a steel plant in NW Italy (700 000 tons of steel year⁻¹) to the air concentrations of PCDDs/PCDFs at local level, through the analysis of measured, modelled and literature data. The study was carried out in an area of 600 km², using air quality data measured by the institutional monitoring network, data obtained from AERMOD simulations and literature data.The measured air concentrations were consistent with literature values for similar areas, and both the homologue profiles and PCA analyses showed a clear distinction between the monitoring stations and the source profiles.All the previous results were confirmed by the air dispersion model (AERMOD), that predicted PCDD/F air concentrations due to the steel plant from four to two orders of magnitude lower than those measured in the monitoring stations, highlighting the presence of other sources.This study outlines the limited influence of the source in the local PCDD/F air concentrations and at the same time the usefulness of a joint analysis of measured, literature and calculated data to correctly evaluate the role of a source to the local pollution. The study also highlights the usefulness of AERMOD as a complementary tool to define the correct placement of monitoring stations and to locate those areas expected to have the highest air concentrations deriving from a source.     

Characterisation of PM10 and PM2.5 particulate matter in the ambient air of Milan (Italy)

24-h simultaneous samplings of PM10 and PM2.5 particulate matter (PM) have been carried out during the period December 1997–September 1998 in the central urban area of Milan. The mass concentrations of the two fractions showed significant daily variations linked to different thermodynamic conditions of the planetary boundary layer (PBL) and characterised by higher values during wintertime. The elemental composition, determined by energy dispersive X-ray fluorescence technique, was quite different in the two fractions: in the finer one the presence of elements with crustal origin is reduced while the anthropogenic elements, with a relevant environmental and health impact, appear to be enriched. The composition data allowed a quantification of two major components of the atmospheric particulate: sulphates (mainly of secondary origin) and particles with crustal origin. An important but unmeasured component is likely constituted by organic and elemental carbon compounds.The multivariate analysis of elements, gaseous pollutants and mass concentration data-sets leads to the identification of four main sources contributing to PM10 and PM2.5 composition: vehicles exhaust emissions, resuspended crustal dust, secondary sulphates and industrial emissions. The existence of a possible background component with non-local origin is also suggested.     

PCDD/Fs and PCBs in ambient air in a highly industrialized city in Northern Italy

Ambient air samples were collected in five locations around a polychlorobiphenyl (PCB) production plant in a highly industrialized city in the north of Italy, for the analysis of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) and PCBs.PCDD/F atmospheric concentrations were lower than those generally detected in urban areas, while PCB concentrations were higher than in urban and industrialized areas in other countries, especially in the locations closest to the plant. To identify source emissions responsible for air pollution we used principal component analysis (PCA) to compare the “fingerprint” of the air in Brescia with some source-related experimental and published data. This analysis showed that the PCDD/F fingerprints were more similar to steel plant emission data, while none of the PCB air patterns were comparable to emission profiles, indicating that different sources are responsible for the concentration of these two pollutants. The highest PCB concentrations detected in the areas closest to the chemical plant are indicative of its impact on the surrounding environment.     

Lichens as sentinels for air pollution at remote alpine areas (Italy)

The present study was undertaken with the aim of using epiphytic lichens as sentinels for air pollution at two remote alpine sites (1,400 and 1,800 m above sea level (asl)) of NW Italy. The results indicated that the site at 1,800 m prompted for early warning indications of biological changes. Although levels of the many elements assayed in samples of the lichen Pseudevernia furfuracea (L.) Zopf, ranging from minor elements (e.g., Al) to ultra-trace (e.g., Pt), were at normal levels, indications of a slowly worsening environment were given by the lichen biodiversity and by damage to cell membranes. The analysis of Pb isotopic ratios suggested that the origin of Pb accumulated in lichens is not local, but linked to the long-range transport by air masses. It was concluded that the origin of pollutants is from air mass coming from the Po plain of Italy and from densely populated areas of Switzerland and France.     

PCDD/Fs in ambient air in north-east Italy: The role of a MSWI inside an industrial area

The stack gases of a municipal solid waste incinerator (MSWI), and ambient air were sampled in four locations around the plant for the analysis of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs). The sampling area was close to an industrial area near Trieste, in north-east Italy. The purpose of the study was to estimate the impact of the MSWI emissions and to distinguish the contribution of these emissions from other potential emission sources in the industrial area.PCDD/F atmospheric concentrations were similar to those generally detected in urban–rural areas with one location about 2–3 times more contaminated than the others. Since the most contaminated location was inside the industrial area but upwind of the MSWI, principal component analysis (PCA) was used to establish whether other sources were the cause. This analysis clearly showed that a local steel plant’s emission was the main source of PCDDs/Fs in ambient air. This study highlights the usefulness of multivariate data analysis such as PCA to identify, among different potential emission sources, the one really responsible for the contamination.     

In situ monitoring of urban air in Southern Italy with the Tradescantia micronucleus bioassay and semipermeable membrane devices (SPMDs)

This study was designed to assess toxic and genotoxic compounds in the urban air of Caserta, South Italy using cuttings from the plant Tradescantia #4430. In situ monitoring of gaseous pollutans was made at 17 sampling points in two seasons of the year. Genotoxicity was evaluated by recording the micronuclei in meiotic pollen mother cells (Trad-MCN assay). In addition, the passive sampler semipermeable membrane devices (SPMDs) were deployed at the sampling points with a significant increase in micronuclei frequency. SPMDs concentrated priority organic pollutants were identified by high performance liquid chromatography and gas chromatography, while toxicity and mutagenesis were assessed on the bacterium Vibrio fischeri using the Microtox and Mutatox systems respectively. Significant toxic and mutagenic effects were observed at different points on the town grid and SPMDs effectively concentrated trace contaminants. The relationship between what was present in the air sampled by SPMDs and the micronuclei frequency was also explored.     

Illicit crops and armed conflict as constraints on biodiversity conservation in the Andes region

Coca, once grown for local consumption in the Andes, is now produced for external markets, often in areas with armed conflict. Internationally financed eradication campaigns force traffickers and growers to constantly relocate, making drug-related activities a principal cause of forest loss. The impact on biodiversity is known only in general terms, and this article presents the first regional analysis to identify areas of special concern, using bird data as proxy. The aim of conserving all species may be significantly constrained in the Santa Marta and Perijá mountains, Darién, some parts of the Central Andes in Colombia, and between the middle Mara?ón and middle Huallaga valleys in Peru. Solutions to the problem must address the root causes: international drug markets, long-lasting armed conflict, and lack of alternative income for the rural poor.     

Illicit drugs in Canadian municipal wastewater and estimates of community drug use

In this study of wastewater treatment plants in three Canadian cities, selected illicit drugs, including cocaine and its major metabolite, benzoylecgonine (BE), amphetamine, methamphetamine and ecstasy (i.e. MDMA) were detected in untreated wastewater. Cocaine was the most widely used illicit drug at a median level for the 3 cities of 15.7 doses per day per 1000 people. For the other drugs, the median doses per day per 1000 people were 1.8 for amphetamine, 4.5 for methamphetamine and 0.4 for ecstasy. Methamphetamine use was highest in the largest city and cocaine use was lowest in the smallest city. Removal of the illicit drugs by wastewater treatment was generally >50%, except in a WWTP that uses primary treatment. The community consumption estimate for ecstasy in the present study is far below published estimates of the prevalence of ecstasy use among the Canadian population, which may be due to only occasional use of ecstasy.     

Estimation of road vehicle exhaust emissions from 1992 to 2010 and comparison with air quality measurements in Genoa,Italy

An investigation into road transport exhaust emissions in the Genoa urban area was performed by comparing the quantities of carbon monoxide (CO), nitrogen oxides (NO_x), nitrogen dioxide (NO₂) and particulate matter (PM) emitted by different vehicle categories with air quality measurements referred to the same pollutants. Exhaust emissions were evaluated by applying the PROGRESS (computer PROGramme for Road vehicle EmiSSions evaluation) code, developed by the Internal Combustion Engines Group of the University of Genoa, to eight different years (from 1992 to 2010), considering spark ignition and Diesel passenger cars and light duty vehicles, heavy duty vehicles and buses, motorcycles and mopeds. Changes in terms of vehicles number, mileage and total emissions are presented together with relative distributions among the various vehicle categories. By comparing 1992 and 2010 data, calculated trends show a 7% increase in the number of vehicles, with total mileage growing at a faster rate (approx. 22%); total emissions decrease considerably, by approximately 50% for NO_x and PM, 70% for HC and 80% for CO, due to improvements in engines and fuels forced by the stricter European legislation and the fleet renewal, while primary NO₂ emission will be very close to 1992 level, after a decrease of about 18% in 2000.Air quality was analysed by selecting traffic and background measuring stations from the monitoring network managed by the Environmental Department of the Province of Genoa: average annual concentrations of considered pollutants from 1994 to 2007 were calculated in order to obtain the relative historical trends and compare them with European public health limits and with road vehicle emissions. Though an important reduction in pollutant concentrations has been achieved as a consequence of cleaner vehicles, some difficulties in complying with present and/or future NO₂ and PM₁₀ limits are also apparent, thus requiring suitable measures to be taken by the local authorities.     

Application of a Lagrangian particle model to assess the impact of harbour,industrial and urban activities on air quality in the Taranto area,Italy

This paper evaluates the relative impact on air quality of harbour emissions, with respect to other emission sources located in the same area. The impact assessment study was conducted in the city of Taranto, Italy. This area was considered as representative of a typical Mediterranean harbour region, where shipping, industries and urban activities co-exist at a short distance, producing an ideal case to study the interaction among these different sources. Chemical and meteorological field campaigns were carried out to provide data to this study. An emission inventory has been developed taking into account industrial sources, traffic, domestic heating, fugitive and harbour emissions. A 3D Lagrangian particle dispersion model (SPRAY) has then been applied to the study area using reconstructed meteorological fields calculated by the diagnostic meteorological model MINERVE. 3D short term hourly concentrations have been computed for both all and specific sources. Industrial activities are found to be the main contributor to SO₂. Industry and traffic emissions are mainly responsible for NO_x simulated concentrations. CO concentrations are found to be mainly related to traffic emissions, while primary PM₁₀ simulated concentrations tend to be linked to industrial and fugitive emissions. Contributions of harbour activities to the seasonal average concentrations of SO₂ and NO_x are predicted to be up to 5 and 30 μg m⁻³, respectively to be compared to a overall peak values of 60 μg m⁻³ for SO₂ and 70 μg m⁻³ for NO_x. At selected urban monitoring stations, SO₂ and NO_x average source contributions are predicted to be both of about 9% from harbour activities, while 87% and 41% respectively of total concentrations are predicted to be of industrial origin.     

The influence of the North-Föhn on tracer organic compounds in ambient air PM10 at a pre-alpine site in Northern Italy

The ambient air in Northern Italy is characterised by relatively high PAH and PM₁₀ concentrations in relation to calm wind and intensive temperature inversions, especially during cold periods. These stagnant conditions are occasionally interrupted by North-Föhn events, which cause a drop in relative humidity and an increase in O₃ levels, indicating the mixing of local and free troposphere air flows. In this study the influence of the North-Föhn on concentrations of tracer organic compounds, including polycyclic aromatic hydrocarbons (PAHs), PM₁₀, O₃ and black carbon (BC) was studied during a North-Föhn event in November 2007. Large fluctuations in the concentration of these compounds, as well as changes in PM₁₀ composition due to daytime and night-time variations of local source emissions were observed. Although these events occur at low frequencies (6-10%) they can for short periods, strongly affect the regional air quality by quickly decreasing the concentrations of these tracer organic compounds.