A four-year size-segregated characterization study of particles PM10, PM2.5 and PM1 depending on air mass origin at Melpitz

PM₁₀ measurements were started in November 1992 at Melpitz site. The mean PM₁₀ concentration in 1993 was 38 μg m^?3 in the summer season (May until October) and about 44 μg m^?3 in the winter season (November until April). The mean PM₁₀ level decreased until 1999 and varies now in ranges from 20–34 μg m^?3 to 17–24 μg m^?3 (minimum and maximum mean values for 1999–2008) in winter and summer seasons, respectively. High volume filter samples of particles PM₁₀, PM_2.5 and PM₁ were characterized for mass, water-soluble ions, organic and elemental carbon from 2004 until 2008. The percentage of PM_2.5 in PM₁₀ varies between summer (71.6%) and winter seasons (81.9%). Mean concentrations of PM₁₀, PM_2.5 and PM₁ in Melpitz were 20, 15, and 13 μg m^?3 in 2004, 22, 18, and 13 μg m^?3 in 2005, 24, 19, and 12 μg m^?3 in 2006 and 22, 17, and 12 μg m^?3 in 2007, respectively. In the four winters the rural background concentration PM₁₀ at Melpitz exceeded the daily 50 μg m^?3 limit for Europe on 8, 8, 7 and 6 days, respectively.Findings for a simple two-sector-classification of the samples (May 2004 until April 2008) using 96-h backward trajectories for the identification of source regions are: Air masses were transported most of time (60%) from the western sector and secondly (17%) from the eastern sector. The lowest daily mean mass concentration PM₁₀ were found during western inflow in summer (17 μg m^?3) containing low amounts of sulphate (2.4 μg m^?3), nitrate (1.7 μg m^?3), ammonium (1.1 μg m^?3) and TC (3.7 μg m^?3). In opposite the highest mean mass concentration PM₁₀ was found during eastern inflow in winter (35 μg m^?3) with high amounts of sulphate (6.1 μg m^?3), nitrate (5.4 μg m^?3), ammonium (3.8 μg m^?3) and TC (9.4 μg m^?3). An estimation of secondary formed OC (SOA) shows 0.8–0.9 μg m^?3 for air masses from West and 2.1–2.2 μg m^?3 from East. The seasonal difference can be neglected.The half-hourly measurements of the particle mass concentration PM₁₀ evaluated as mean daily courses using a TEOM^® show low values (14–21 μg m^?3) in summer and winter for air masses transported from West and the highest concentrations (31–38 μg m^?3) in winter for air masses from East.The results demonstrate the influence of meteorological parameters on long-range transport, secondary particle mass formation and re-emission which modify mass concentration and composition of PM₁₀, PM_2.5 and PM₁. Melpitz site is located in the East of Germany faraway from strong local anthropogenic emissions (rural background). Therefore, this site is suitable for investigation of the influence of long-range transport of air pollution in continental air masses from the East with source regions inside and outside of the European Union.     

Secondary organic aerosol formation from the oxidation of aromatic hydrocarbons in the presence of dry submicron ammonium sulfate aerosol

A laboratory study was conducted to examine formation of secondary organic aerosols. A smog chamber system was developed for studying gas–aerosol interactions in a dynamic flow reactor. These experiments were conducted to investigate the fate of gas and aerosol phase compounds generated from hydrocarbon–nitrogen oxide (HC/NO_x) mixtures irradiated in the presence of fine (<2.5 μm) particulate matter. The goal was to determine to what extent photochemical oxidation products of aromatic hydrocarbons contribute to secondary organic aerosol formation through uptake on pre-existing inorganic aerosols in the absence of liquid water films. Irradiations were conducted with toluene, p-xylene, and 1,3,5-trimethylbenzene in the presence of NO_x and ammonium sulfate aerosol, with propylene added to enhance the production of radicals in the system. The secondary organic aerosol yields were determined by dividing the mass concentration of organic fraction of the aerosol collected on quartz filters by the mass concentration of the aromatic hydrocarbon removed by reaction. The mass concentration of the organic fraction was obtained by multiplying the measured organic carbon concentration by 2.0, a correction factor that takes into account the presence of hydrogen, nitrogen, and oxygen atoms in the organic species. The mass concentrations of ammonium, nitrate, and sulfate concentrations as well as the total mass of the aerosols were measured. A reasonable mass balance was found for each of the aerosols. The largest secondary organic aerosol yield of 1.59±0.40% was found for toluene at an organic aerosol concentration of 8.2 μm⁻³, followed by 1.09±0.27% for p-xylene at 6.4 μg m⁻³, and 0.41±0.10% for 1,3,5-trimethylbenzene at 2.0 μg m⁻³. In general, these results agree with those reported by Odum et al. and appear to be consistent with the gas–aerosol partitioning theory developed by Pankow. The presence of organic in the aerosol did not affect significantly the hygroscopic properties of the aerosol.     

A kinetic mechanism for predicting secondary organic aerosol formation from toluene oxidation in the presence of NOx and natural sunlight

A kinetic mechanism to predict secondary organic aerosol (SOA) formation from the photo-oxidation of toluene was developed. Aerosol phase chemistry that includes nucleation, gas–particle partitioning and particle-phase reactions as well as the gas-phase chemistry of toluene and its degradation products were represented. The mechanism was evaluated against experimental data obtained from the University of North Carolina (UNC) 270 m³ dual outdoor aerosol smog chamber facility. The model adequately simulates the decay of toluene, the nitric oxide (NO) to nitrogen dioxide (NO₂) conversion and ozone formation. It also provides a reasonable prediction of SOA production under different conditions that range from 15 to 300 μg m⁻³. Speciation of simulated aerosol material shows that up to 70% of the aerosol mass comes from oligomers and polymers depending on initial reactant concentrations. The dominant particle-phase species predicted by the mechanism are glyoxal oligomers, ketene oligomers from the photolysis of the toluene OH reaction product 2-methyl-2,4-hexadienedial, organic nitrates, methyl nitro-phenol analogues, C7 organic peroxides, acylperoxy nitrates and for the low-concentration experiments, unsaturated hydroxy nitro acids.     

Experimental and statistical analyses to characterize in-vehicle fine particulate matter behavior inside public transit buses operating on B20-grade biodiesel fuel

This paper presents results from an in-vehicle air quality study of public transit buses in Toledo, Ohio, involving continuous monitoring, and experimental and statistical analyses to understand in-vehicle particulate matter (PM) behavior inside buses operating on B20-grade biodiesel fuel. The study also focused on evaluating the effects of vehicle’s fuel type, operating periods, operation status, passenger counts, traffic conditions, and the seasonal and meteorological variation on particulates with aerodynamic diameter less than 1 micron (PM_1.0). The study found that the average PM_1.0 mass concentrations in B20-grade biodiesel-fueled bus compartments were approximately 15 μg m^?3, while PM_2.5 and PM₁₀ concentration averages were approximately 19 μg m^?3 and 37 μg m^?3, respectively. It was also observed that average hourly concentration trends of PM_1.0 and PM_2.5 followed a “μ-shaped” pattern during transit hours.Experimental analyses revealed that the in-vehicle PM_1.0 mass concentrations were higher inside diesel-fueled buses (10.0–71.0 μg m^?3 with a mean of 31.8 μg m^?3) as compared to biodiesel buses (3.3–33.5 μg m^?3 with a mean of 15.3 μg m^?3) when the windows were kept open. Vehicle idling conditions and open door status were found to facilitate smaller particle concentrations inside the cabin, while closed door facilitated larger particle concentrations suggesting that smaller particles were originating outside the vehicle and larger particles were formed within the cabin, potentially from passenger activity. The study also found that PM_1.0 mass concentrations at the back of bus compartment (5.7–39.1 μg m^?3 with a mean of 28.3 μg m^?3) were higher than the concentrations in the front (5.7–25.9 μg m^?3 with a mean of 21.9 μg m^?3), and the mass concentrations inside the bus compartment were generally 30–70% lower than the just-outside concentrations. Further, bus route, window position, and time of day were found to affect the in-vehicle PM concentrations significantly. Overall, the in-vehicle PM_1.0 concentrations inside the buses operating on B20-grade biodiesel ranged from 0.7 μg m^?3 to 243 μg m^?3, with a median of 11.6 μg m^?3.Statistical models developed to study the effects of vehicle operation and ambient conditions on in-vehicle PM concentrations suggested that while open door status was the most important influencing variable for finer particles and higher passenger activity resulted in higher coarse particles concentrations inside the vehicle compartments, ambient PM concentrations contributed to all PM fractions inside the bus irrespective of particle size.     

Meteorological variability in NO2 and PM10 concentrations in the Netherlands and its relation with EU limit values

The extent of the exceedance of the EU limit values for nitrogen dioxide (NO₂) and particulate matter (PM₁₀) concentrations within the Netherlands is expected to decrease significantly, in the coming years. Whether limit values will actually be exceeded, in the next decade, depends not only on European, national and local policies, but also on the effects of inevitable interannual meteorological fluctuations. An analysis of model calculations and measurements yields variations (1 sigma) in the annual average concentration of about 5% for NO₂ and 9% for PM₁₀, due to meteorological fluctuations. These deviations from long-term average concentrations affect assessments of future levels, set against limit values. For instance, an NO₂ concentration of 39 μg m^?3, estimated for a given year with long-term average meteorology, indicates that it is likely (chance >66%) that the limit value of 40 μg m^?3 will not be exceeded in that particular year. At the same time, the estimation also indicates, for example, that this situation is unlikely (change <33%) to continue for three years in a row. However, with an estimated concentration of 38 μg m^?3, it is likely that the limit value will not be exceeded for three years in a row. The limit value for the daily average PM₁₀ concentration is equivalent to an annual average of about 32 μg m^?3. This threshold is unlikely to be exceeded for three years in a row, when an annual average concentration of 29 μg m^?3 is estimated. Interannual variations in concentrations of NO₂ and PM₁₀ are linked to large-scale meteorological fluctuations. Therefore, similar results can be expected for other European countries.     

Experimental evidence for a significant contribution of cellulose to indoor aerosol mass concentration

An apartment bedroom located in a residential area of Aveiro (Portugal) was selected with the aim of characterizing the cellulose content of indoor aerosol particles. Two sets of samples were taken: (1) PM₁₀ collected simultaneously in indoor and outdoor air; (2) PM₁₀ and PM_2.5 collected simultaneously in indoor air. The aerosol particles were concentrated on quartz fibre filters with low-volume samplers equipped with size selective inlets. The filters were weighed and then extracted for cellulose analysis by an enzymatic method. The average indoor cellulose concentration was 1.01 ± 0.24 μg m^?3, whereas the average outdoor cellulose concentration was 0.078 ± 0.047 μg m^?3, accounting for 4.0% and 0.4%, respectively, of the PM₁₀ mass. The corresponding average ratio between indoor and outdoor cellulose concentrations was 11.1 ± 4.9, indicating that cellulose particles were generated indoors, most likely due to the handling of cotton-made textiles as a result of routine daily activities in the bedroom. Indoor cellulose concentrations averaged 1.22 ± 0.53 μg m^?3 in the aerosol coarse fraction (determined from the difference between PM₁₀ and PM_2.5 concentrations) and averaged 0.38 ± 0.13 μg m^?3 in the aerosol fine fraction. The average ratio between the coarse and fine fractions of cellulose concentrations in the indoor air was 3.6 ± 2.1. This ratio is in line with the primary origin of this biopolymer. Results from this study provide the first experimental evidence in support of a significant contribution of cellulose to the mass of suspended particles in indoor air.     

Quantitative chemical composition and characteristics of aerosols over western India: One-year record of temporal variability

One-year quantitative chemical data set consisting of water-soluble constituents (NH₄⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Cl^?, NO₃^?, SO₄^2? and HCO₃^?), crustal and trace elements (Al, Fe, Ca, Mg, K, Mn, Zn, Pb) and carbonaceous species (OC, EC) in ambient aerosols, collected over an urban site located in a high-dust semi-arid region of western India, reveals excellent linear relationship (r² = 0.92; slope = 0.96 ± 0.05) between gravimetrically assessed TSP (total suspended particulates) and chemically analyzed aerosol mass. The TSP abundance ranging from 60 to 250 μg m^?3, over a period of 12 months (January–December), is dominated by mineral dust (～70%); whereas contribution from sea-salts, anthropogenic and carbonaceous species exhibits significant temporal variability depending upon the wind regimes. The mineral dust is enriched in Ca, Mg and Fe with respect to upper continental crust (UCC); whereas Zn and Pb exhibit a characteristic anthropogenic source and high enrichment factors. The carbonaceous species show significant seasonality; with dominance of OC (range: 4.6–28 μg m^?3; average: 12.8 μg m^?3; SD: 6.8) and minor contribution from EC (range: 0.3–4.4 μg m^?3; average: 2.4 μg m^?3; SD: 1.4). The observed concentrations are significantly lower than those reported for the metro cities in South Asia but the OC/EC ratios (range: 4.3–35; average: 8.3; SD: 5.7) are significantly higher than the characteristic ratio (～2–4) reported for the urban atmosphere. Such quantitative chemical characterization of aerosols is essential in assessing their role in atmospheric chemistry and climate change. This study could also be useful in understanding the physical and optical aerosol properties documented from the same site and thus, in validating regional climate models.     

Speciation and diurnal variation of thoracic,fine thoracic and sub-micrometer airborne particulate matter at naturally ventilated office environments

Thoracic (PM₁₀), fine thoracic (PM_2.5) and sub-micrometer (PM₁) airborne particulate matter was sampled during day and night. In total, about 100 indoor and outdoor samples were collected for each fraction at ten different office environments. Energy-dispersive X-ray fluorescence spectrometry and ion chromatography were applied for the quantification of some major and minor elements and ions in the collected aerosols. During daytime, mass concentrations were in the ranges: 11–29, 8.1–24, and 6.6–18 μg m^?3, with averages of 20 ± 1, 15.0 ± 0.9, and 11.0 ± 0.8 μg m^?3, respectively. At night, mass concentrations were found to be significantly lower for all fractions. Indoor PM₁ concentrations exceeded the corresponding outdoor levels during office hours and were thought to be elevated by office printers. Particles with diameters between 1 and 2.5 μm and 2.5 and 10 μm were mainly associated with soil dust elements and were clearly subjected to distinct periods of settling/resuspension. Indoor NO₃^? levels were found to follow specific microclimatic conditions at the office environments, while daytime levels of sub-micrometer Cl^? were possibly elevated by the use of Cl-containing cleaning products. Indoor carbon black concentrations were sometimes as high as 22 μg m^?3 and were strongly correlated with outdoor traffic conditions.     

Multi-year hourly PM2.5 carbon measurements in New York: Diurnal,day of week and seasonal patterns

Multi-year hourly measurements of PM_2.5 elemental carbon (EC) and organic carbon (OC) from a site in the South Bronx, New York were used to examine diurnal, day of week and seasonal patterns. The hourly carbon measurements also provided temporally resolved information on sporadic EC spikes observed predominantly in winter. Furthermore, hourly EC and OC data were used to provide information on secondary organic aerosol formation. Average monthly EC concentrations ranged from 0.5 to 1.4 μg m^?3 with peak hourly values of several μg m^?3 typically observed from November to March. Mean EC concentrations were lower on weekends (approximately 27% lower on Saturday and 38% lower on Sunday) than on weekdays (Monday to Friday). The weekday/weekend difference was more pronounced during summer months and less noticeable during winter. Throughout the year EC exhibited a similar diurnal pattern to NO_x showing a pronounced peak during the morning commute period (7–10 AM EST). These patterns suggest that EC was impacted by local mobile emissions and in addition by emissions from space heating sources during winter months. Although EC was highly correlated with black carbon (BC) there was a pronounced seasonal BC/EC gradient with summer BC concentrations approximately a factor of 2 higher than EC. Average monthly OC concentrations ranged from 1.0 to 4.1 μg m^?3 with maximum hourly concentrations of 7–11 μg m^?3 predominantly in summer or winter months. OC concentrations generally correlated with PM_2.5 total mass and aerosol sulfate and with NO_x during winter months. OC showed no particular day of week pattern. The OC diurnal pattern was typically different than EC except in winter when OC tracked EC and NO_x indicating local primary emissions contributed significantly to OC during winter at the urban location. On average secondary organic aerosol was estimated to account for 40–50% of OC during winter and up to 63–73% during summer months.     

Simulating the fine and coarse inorganic particulate matter concentrations in a polluted megacity

A three dimensional chemical transport model (PMCAMx) is applied to the Mexico City Metropolitan Area (MCMA) in order to simulate the chemical composition and mass of the major PM₁ (fine) and PM_1–10 (coarse) inorganic components and determine the effect of mineral dust on their formation. The aerosol thermodynamic model ISORROPIA-II is used to explicitly simulate the effect of Ca, Mg, and K from dust on semi-volatile partitioning and water uptake. The hybrid approach is applied to simulate the inorganic components, assuming that the smallest particles are in thermodynamic equilibrium, while describing the mass transfer to and from the larger ones. The official MCMA 2004 emissions inventory with improved dust and NaCl emissions is used. The comparison between the model predictions and measurements during a week of April of 2003 at Centro Nacional de Investigacion y Capacitacion Ambiental (CENICA) “Supersite” shows that the model reproduces reasonably well the fine mode composition and its diurnal variation. Sulfate predicted levels are relatively uniform in the area (approximately 3 μg m^?3), while ammonium nitrate peaks in Mexico City (approximately 7 μg m^?3) and its concentration rapidly decreases due to dilution and evaporation away from the urban area. In areas of high dust concentrations, the associated alkalinity is predicted to increase the concentration of nitrate, chloride and ammonium in the coarse mode by up to 2 μg m^?3 (a factor of 10), 0.4 μg m^?3, and 0.6 μg m^?3 (75%), respectively. The predicted ammonium nitrate levels inside Mexico City for this period are sensitive to the physical state (solid versus liquid) of the particles during periods with RH less than 50%.     

Year-long continuous personal exposure to PM2.5 recorded by a fast responding portable nephelometer

Personal exposure to particulate matter of aerodynamic diameter under 2.5 μm (PM_2.5) was monitored using a DustTrak nephelometer. The battery-operated unit, worn by an adult individual for a period of approximately one year, logged integrated average PM_2.5 concentrations over 5 min intervals. A detailed time-activity diary was used to record the experimental subject’s movement and the microenvironments visited. Altogether 239 days covering all the months (except April) were available for the analysis. In total, 60 463 acceptable 5-min averages were obtained. The dataset was divided into 7 indoor and 4 outdoor microenvironments. Of the total time, 84% was spent indoors, 10.9% outdoors and 5.1% in transport. The indoor 5-min PM_2.5 average was higher (55.7 μg m^?3) than the outdoor value (49.8 μg m^?3). The highest 5-min PM_2.5 average concentration was detected in restaurant microenvironments (1103 μg m^?3), the second highest 5-min average concentration was recorded in indoor spaces heated by stoves burning solid fuels (420 μg m^?3). The lowest 5-min mean aerosol concentrations were detected outdoors in rural/natural environments (25 μg m^?3) and indoors at the monitored person’s home (36 μg m^?3). Outdoor and indoor concentrations of PM_2.5 measured by the nephelometer at home and during movement in the vicinity of the experimental subject’s home were compared with those of the nearest fixed-site monitor of the national air quality monitoring network. The high correlation coefficient (0.78) between the personal and fixed-site monitor aerosol concentrations suggested that fixed-site monitor data can be used as proxies for personal exposure in residential and some other microenvironments. Collocated measurements with a reference method (β-attenuation) showed a non-linear systematic bias of the light-scattering method, limiting the use of direct concentration readings for exact exposure analysis.     

PM2.5, soot and NO2 indoor–outdoor relationships at homes,pre-schools and schools in Stockholm,Sweden

In developed nations people spend about 90% of their time indoors. The relationship between indoor and outdoor air pollution levels is important for the understanding of the health effects of outdoor air pollution. Although other studies describe both the outdoor and indoor atmospheric environment, few excluded a priori major indoor sources, measured the air exchange rate, included more than one micro-environment and included the presence of human activity. PM_2.5, soot, NO₂ and the air exchange rate were measured during winter and summer indoors and outdoors at 18 homes (mostly apartments) of 18 children (6–11-years-old) and also at the six schools and 10 pre-schools that the children attended. The three types of indoor environments were free of environmental tobacco smoke and gas appliances, as the aim was to asses to what extent PM_2.5, soot and NO₂ infiltrate from outdoors to indoors. The median indoor and outdoor PM_2.5 levels were 8.4 μg m^?3 and 9.3 μg m^?3, respectively. The median indoor levels for soot and NO₂ were 0.66 m^?1 × 10^?5 and 10.0 μg m^?3, respectively. The respective outdoor levels were 0.96 m^?1 × 10^?5 and 12.4 μg m^?3. The median indoor/outdoor (I/O) ratios were 0.93, 0.76 and 0.92 for PM_2.5, soot and NO₂, respectively. Their infiltration factors were influenced by the micro-environment, ventilation type and air exchange rate, with aggregated values of 0.25, 0.55 and 0.64, respectively. Indoor and outdoor NO₂ levels were strongly associated (R² = 0.71), followed by soot (R² = 0.50) and PM_2.5 (R² = 0.16). In Stockholm, the three major indoor environments occupied by children offer little protection against combustion-related particles and gases in the outdoor air. Outdoor PM_2.5 seems to infiltrate less, but indoor sources compensate.     

The effects of congestions tax on air quality and health

The “Stockholm Trial” involved a road pricing system to improve the air quality and reduce traffic congestion. The test period of the trial was January 3–July 31, 2006. Vehicles travelling into and out of the charge cordon were charged for every passage during weekdays. The amount due varied during the day and was highest during rush hours (20 SEK = 2.2 EUR, maximum 60 SEK per day). Based on measured and modelled changes in road traffic it was estimated that this system resulted in a 15% reduction in total road use within the charged cordon. Total traffic emissions in this area of NO_x and PM10 fell by 8.5% and 13%, respectively. Air quality dispersion modelling was applied to assess the effect of the emission reductions on ambient concentrations and population exposure. For the situations with and without the trial, meteorological conditions and other emissions than from road traffic were kept the same. The calculations show that, with a permanent congestion tax system like the Stockholm Trial, the annual average NO_x concentrations would be lower by up to 12% along the most densely trafficked streets. PM10 concentrations would be up to 7% lower. The limit values for both PM10 and NO₂ would still be exceeded along the most densely trafficked streets. The total population exposure of NO_x in Greater Stockholm (35 × 35 km with 1.44 million people) is estimated to decrease with a rather modest 0.23 μg m^?3. However, based on a long-term epidemiological study, that found an increased mortality risk of 8% per 10 μg m^?3 NO_x, it is estimated that 27 premature deaths would be avoided every year. According to life-table analysis this would correspond to 206 years of life gained over 10 years per 100 000 people following the trial if the effects on exposures would persist. The effect on mortality is attributed to road traffic emissions (likely vehicle exhaust particles); NO_x is merely regarded as an indicator of traffic exposure. This is only the tip of the ice-berg since reductions are expected in both respiratory and cardiovascular morbidity. This study demonstrates the importance of not only assessing the effects on air quality limit values, but also to make quantitative estimates of health impacts, in order to justify actions to reduce air pollution.     

New approach using lidar measurements to characterize spatiotemporal aerosol mass distribution in an underground railway station in Paris

For the first time eye safe lidar measurements were performed at 355 nm simultaneously to in situ measurements in an underground station so as to test the potential interest of active remote sensing measurements to follow the spatiotemporal evolution of aerosol content inside such a confined microenvironment. The purpose of this paper is to describe different methods enabling the conversion of lidar-derived aerosol extinction coefficient into aerosol mass concentrations (PM_2.5 and PM₁₀). A theoretical method based on a well marked linear regression between mass concentrations simulated from the size distribution and extinction coefficients retrieved from Mie calculations provides averaged mass to optics' relations over the campaign for traffic (6.47 × 10⁵ μg m^?2) or no traffic conditions (3.73 × 10⁵ μg m^?2). Two empirical methods enable to significantly reduce CPU time. The first one is based upon the knowledge of size distribution measurements and scattering coefficients from nephelometer and allows retrieving mass to optics' relations for well determined periods or particular traffic conditions, like week-ends, with a good accuracy. The second method, that is more direct, is simply based on the ratio between TEOM concentrations and extinction coefficients obtained from nephelometer. This method is easy to set up but is not suitable for nocturnal measurements where PM stabilization time is short. Lidar signals thus converted into PM concentrations from those approaches with a fine accuracy (30%) provide a spatiotemporal distribution of concentrations in the station. This highlights aerosol accumulation in one side of the station, which can be explained by air displacement from the tunnel entrance. Those results allow expecting a more general use of lidar measurement to survey indoor air quality.     

Determination of aerosol yields from 3-methylcatechol and 4-methylcatechol ozonolysis in a simulation chamber

Secondary Organic Aerosol (SOA) formation during the ozonolysis of 3-methylcatechol (3-methyl-1,2-dihydroxybenzene) and 4-methylcatechol (3-methyl-1,2-dihydroxybenzene) was investigated using a simulation chamber (8 m³) at atmospheric pressure, room temperature (294 ± 2 K) and low relative humidity (5–10%). The initial mixing ratios were as follows (in ppb): 3-methylcatechol (194–1059), 4-methylcatechol (204–1188) and ozone (93–531). The ozone and methylcatechol concentrations were followed by UV photometry and GC–FID (Gas chromatography–Flame ionization detector), respectively and the aerosol production was monitored using a SMPS (Scanning Mobility Particle Sizer). The SOA yields (Y) were determined as the ratio of the suspended aerosol mass corrected for wall losses (M_o) to the total reacted methylcatechol concentrations assuming a particle density of 1.4 g cm^?3. The aerosol formation yield increases as the initial methylcatechol concentration increases, and leads to aerosol yields ranging from 32% to 67% and from 30% to 64% for 3-methylcatechol and 4-methylcatechol, respectively. Y is a strong function of M_o and the organic aerosol formation can be expressed by a one-product gas/particle partitioning absorption model. These data are comparable to those published in a recent study on secondary organic aerosol formation from catechol ozonolysis. To our knowledge, this work represents the first investigation of SOA formation from the ozone reaction with methylcatechols.     

Modelling the formation and atmospheric transport of secondary inorganic aerosols with special attention to regions with high ammonia emissions

Regional simulations of sulfate, nitrate and ammonium aerosols were performed by a nested application of the online-coupled three-dimensional Eulerian model system COSMO-MUSCAT. This was done in a domain covering the northern part of Germany and surrounding regions for the full month of May and a 6-week period in August/September 2006 with the primary focus on secondary inorganic aerosol levels caused by ammonia emissions from domesticated animals and agricultural operations.The results show that in situations with westerly winds ammonium nitrate dominates with concentrations of about 5–10 μg m^?3 whereas the ammonium sulfate concentrations are about 5 μg m^?3. In situations with winds mainly from the East characterized by warmer and dryer air the ammonium sulfate concentrations have their maximum at about 10 μg m^?3 whereas at the same time no ammonium nitrate is present.A reduction of agricultural NH₃ emissions by 50% in a regional scale reduces the ammonium nitrate concentrations to a maximum of 30%, while the ammonium sulfate concentrations are unchanged. The reduction of NH₃ emissions in a more limited area (here in the Federal state of Germany Niedersachsen) does have no noticeable effect neither on ammonium sulfate nor on ammonium nitrate.     

Nitric acid and the origin and size segregation of aerosol nitrate aloft during BRACE 2002

As part of the BRACE 2002 May field intensive, the NOAA Twin Otter flew 21 missions over terrestrial, marine, and mixed terrestrial and marine sites in the greater Tampa, Florida, airshed including over Tampa Bay and the Gulf of Mexico. Aerosols were collected with filter packs and their inorganic fractions analyzed post hoc with ion chromatography. Anion mass dominated both the fine- (particle diameters ⩽2.5 μm) and coarse-mode (particle diameters 10.0–2.5 μm) inorganic fractions: SO₄²⁻in the fine fraction, 3.7 μg m⁻³ on average and Cl⁻ and NO₃⁻ in the coarse fraction, 0.6 μg m⁻³ on average and 1.4 μg m⁻³ on average, respectively. Ammonium ion dominated the inorganic fine-mode cation mass, averaging 1.2 μg m⁻³, presumably in association with SO₄². Coarse-mode cation mass was dominated by Na⁺, but the concentrations of Ca²⁺ and K⁺ together often equaled or exceeded the Na⁺ mass which was, on average, 0.6 μg m⁻³. Nitrate appeared predominantly in the coarse rather than the fine fraction, as expected, and the fine fraction never contributed >15% of the total NO₃ concentration. Nitric acid dominated the NO₃⁻ contribution from both aerosol size fractions, and constituted at least 45% of the total NO₃ in all samples. Coarse-mode Cl⁻ depletion, and hence NO₃⁻ replacement, reached 100% within the first 4 h of plume travel from the urban core in some samples, although it was most often less than 100% and slightly below the expected 1:1 ratio with coarse-mode NO₃⁻ concentration: the slope of the regression line of NO₃⁻ concentration to Cl⁻ depletion was 0.9 in the coarse fraction. In addition, terrestrial samples were markedly lower in Cl⁻ depletion, and thus in substituted NO₃^–, than were marine and mixed samples: 15–25% depletion in terrestrial samples vs. 50–65% in marine samples with the same air mass age. Thus, we conclude that NO₃⁻ and its progenitor compound HNO₃ were present in the Tampa airshed in insufficient amounts to titrate fully the slightly alkaline coarse-mode particles there, and to replace completely the Cl⁻ from the coarse-mode NaCl.     

Impact of smoking on in-vehicle fine particle exposure during driving

Indoor smoking ban in public places can reduce secondhand smoke (SHS) exposure. However, smoking in cars and homes has continued. The purpose of this study was to assess particulate matter less than 2.5 μm (PM_2.5) concentration in moving cars with different window opening conditions. The PM_2.5 level was measured by an aerosol spectrometer inside and outside moving cars simultaneously, along with ultrafine particle (UFP) number concentration, speed, temperature and humidity inside cars. Two sport utility vehicles were used. Three different ventilation conditions were evaluated by up to 20 repeated experiments. In the pre-smoking phase, average in-vehicle PM_2.5 concentrations were 16–17 μg m^?3. Regardless of different window opening conditions, the PM_2.5 levels promptly increased when smoking occurred and decreased after cigarette was extinguished. Although only a single cigarette was smoked, the average PM_2.5 levels were 506–1307 μg m^?3 with different window opening conditions. When smoking was ceased, the average PM_2.5 levels for 15 min were several times higher than the US National Ambient Air Quality Standard of 35 μg m^?3. It took longer than 10 min to reach the level of the pre-smoking phase. Although UFP levels had a similar temporal profile of PM_2.5, the increased levels during the smoking phase were relatively small. This study demonstrated that the SHS exposure in cars with just a single cigarette being smoked could exceed the US EPA NAAQS under realistic window opening conditions. Therefore, the findings support the need for public education against smoking in cars and advocacy for a smoke-free car policy.     

Source apportionment of wintertime secondary organic aerosol during the California regional PM10/PM2.5 air quality study

The UCD/CIT air quality model with the Caltech Atmospheric Chemistry Mechanism (CACM) was used to predict source contributions to secondary organic aerosol (SOA) formation in the San Joaquin Valley (SJV) from December 15, 2000 to January 7, 2001. The predicted 24-day average SOA concentration had a maximum value of 4.26 μg m^?3 50 km southwest of Fresno. Predicted SOA concentrations at Fresno, Angiola, and Bakersfield were 2.46 μg m^?3, 1.68 μg m^?3, and 2.28 μg m^?3, respectively, accounting for 6%, 37%, and 4% of the total predicted organic aerosol. The average SOA concentration across the entire SJV was 1.35 μg m^?3, which accounts for approximately 20% of the total predicted organic aerosol. Averaged over the entire SJV, the major SOA sources were solvent use (28% of SOA), catalyst gasoline engines (25% of SOA), wood smoke (16% of SOA), non-catalyst gasoline engines (13% of SOA), and other anthropogenic sources (11% of SOA). Diesel engines were predicted to only account for approximately 2% of the total SOA formation in the SJV because they emit a small amount of volatile organic compounds relative to other sources. In terms of SOA precursors within the SJV, long-chain alkanes were predicted to be the largest SOA contributor, followed by aromatic compounds. The current study identifies the major known contributors to the SOA burden during a winter pollution episode in the SJV, with further enhancements possible as additional formation pathways are discovered.     

Concentrations,seasonal variations,and transport of carbonaceous aerosols at a remote Mountainous region in western China

Carbonaceous aerosol concentrations were determined for total suspended particle samples collected from Muztagh Ata Mountain in western China from December 2003 to February 2006. Elemental carbon (EC) varied from 0.004 to 0.174 μg m^?3 (average = 0.055 μg m^?3) while organic carbon (OC) ranged from 0.12 to 2.17 μg m^?3 and carbonate carbon (CC) from below detection to 3.57 μg m^?3. Overall, EC was the least abundant fraction of carbonaceous species, and the EC concentrations approached those in some remote polar areas, possibly representing a regional background. Low EC and OC concentrations occurred in winter and spring while high CC in spring and summer was presumably due to dust from the Taklimakan desert, China. OC/EC ratios averaged 10.0, and strong correlations between OC and EC in spring–winter suggest their cycles are coupled, but lower correlations in summer–autumn suggest influences from biogenic OC emissions and secondary OC formation. Trajectory analyses indicate that air transported from outside of China brings ～0.05 μg m^?3 EC, ～0.42 μg m^?3 OC, and ～0.10 μg m^?3 CC to the site, with higher levels coming from inside China. The observed EC was within the range of loadings estimated from a glacial ice core, and implications of EC-induced warming for regional climate and glacial ice dynamics are discussed.