Aircraft measurements of O3, NOx,CO, VOCs,and SO2 in the Yangtze River Delta region

In this study, air pollutants, including ozone (O₃), nitrogen oxides (NO_x = NO + NO₂), carbon monoxides (CO), sulfur dioxide (SO₂), and volatile organic compounds (VOCs) measured in the Yangtze River Delta (YRD) region during several air flights between September/30 and October/11 are analyzed. This measurement provides horizontal and vertical distributions of air pollutants in the YRD region. The analysis of the result shows that the measured O₃ concentrations range from 20 to 60 ppbv. These values are generally below the US national standard (84 ppbv), suggesting that at the present, the O₃ pollutions are modest in this region. The NO_x concentrations have strong spatial and temporal variations, ranging from 3 to 40 ppbv. The SO₂ concentrations also have large spatial and temporal variations, ranging from 1 to 35 ppbv. The high concentrations of CO are measured with small variations, ranging from 3 to 7 ppmv. The concentrations of VOCs are relatively low, with the total VOC concentrations of less than 6 ppbv. The relative small VOC concentrations and the relative large NO_x concentrations suggest that the O₃ chemical formation is under a strong VOC-limited regime in the YRD region. The measured O₃ and NO_x concentrations are strongly anti-correlated, indicating that enhancement in NO_x concentrations leads to decrease in O₃ concentrations. Moreover, the O₃ concentrations are more sensitive to NO_x concentrations in the rural region than in the city region. The ratios of Δ[O₃]/Δ[NO_x] are ?2.3 and ?0.25 in the rural and in the city region, respectively. In addition, the measured NO_x and SO₂ concentrations are strongly correlated, highlighting that the NO_x and SO₂ are probably originated from same emission sources. Because SO₂ emissions are significantly originated from coal burnings, the strong correlation between SO₂ and NO_x concentrations suggests that the NO_x emission sources are mostly from coal burned sources. As a result, the future automobile increases could lead to rapid enhancements in O₃ concentrations in the YRD region.     

Outdoor air pollution in close proximity to a continuous point source

Data are lacking on human exposure to air pollutants occurring in ground-level outdoor environments within a few meters of point sources. To better understand outdoor exposure to tobacco smoke from cigarettes or cigars, and exposure to other types of outdoor point sources, we performed more than 100 controlled outdoor monitoring experiments on a backyard residential patio in which we released pure carbon monoxide (CO) as a tracer gas for continuous time periods lasting 0.5–2 h. The CO was emitted from a single outlet at a fixed per-experiment rate of 120–400 cc min^?1 (～140–450 mg min^?1). We measured CO concentrations every 15 s at up to 36 points around the source along orthogonal axes. The CO sensors were positioned at standing or sitting breathing heights of 2–5 ft (up to 1.5 ft above and below the source) and at horizontal distances of 0.25–2 m. We simultaneously measured real-time air speed, wind direction, relative humidity, and temperature at single points on the patio. The ground-level air speeds on the patio were similar to those we measured during a survey of 26 outdoor patio locations in 5 nearby towns. The CO data exhibited a well-defined proximity effect similar to the indoor proximity effect reported in the literature. Average concentrations were approximately inversely proportional to distance. Average CO levels were approximately proportional to source strength, supporting generalization of our results to different source strengths. For example, we predict a cigarette smoker would cause average fine particle levels of approximately 70–110 μg m^?3 at horizontal distances of 0.25–0.5 m. We also found that average CO concentrations rose significantly as average air speed decreased. We fit a multiplicative regression model to the empirical data that predicts outdoor concentrations as a function of source emission rate, source–receptor distance, air speed and wind direction. The model described the data reasonably well, accounting for ～50% of the log-CO variability in 5-min CO concentrations.     

Flue gas discharge from cooling towers. Wind tunnel investigation of building downwash effects on ground-level concentrations

German power plants are required to meet new emission standards which limit the maximum sulfur dioxide (SOs) concentration in flue gas discharges to 400 mg m⁻³. To achieve this level of reduction in SO₂ concentration, wet scrubbing is necessary for large plants using lignite or hard coal.Wet scrubbing results in a significant reduction in the flue gas temperature leading to low effective stack heights. Instead of using stack gas reheating to achieve the plume rise necessary to satisfy local environmental standards, it was proposed to discharge the scrubbed flue gas from the existing natural-draft cooling towers (NDCT). This method should be effective in reducing local ground-level concentrations since NDCT-plumes are typically very buoyant (densimetric Froude number below 1 ) and normally reach considerable heights of rise. Only under strong wind conditions does the situation reverse itself. For such strong winds, the NDCT-plume is subject to tower and building downwash with the possibility of unacceptably high ground-level concentrations.For a 2700 MW_e lignite-fired power plant near Cologne, a wind tunnel study was carried out to investigate the effects of tower and building downwash effects on the ground-level concentrations of SO₂ produced by discharging the scrubbed flue gas from the natural-draft cooling towers. Also, a comparison was made between the ground-level concentrations produced by the cooling tower discharge method and those produced by a traditional stack. It was found that for low and intermediate wind speeds, the groundlevel concentrations are lower for the case of the cooling tower discharge. Only for strong winds, which occur only very rarely at most German sites, did the conventional stack discharge appear to be superior.     

Field use of semipermeable membrane devices (SPMDs) for passive air sampling of polycyclic aromatic hydrocarbons: Opportunities and limitations

Semipermeable membrane devices (SPMDs) were used for measurements in air of twelve polycyclic aromatic hydrocarbons (PAHs) in two Genoa locations, both on building roofs, distant 300 m from each other. The first, site A, was in front a dismissing steel complex and the second, site B, was in an urban area overlooking a busy thoroughfare. SPMDs were deployed contemporary at the two sites, in nine monthly samplings, from April 2007 to May 2008. The amount of sequestered PAHs, in sites A and B, ranged between 61–267 ng SPMD^?1 d^?1 and 50–535 ng SPMD^?1 d^?1, respectively.PAHs profiles highlighted seasonal differences and suggested the possible role of different PAHs sources in the two areas. In particular, the contribution of remediation works of the steel complex was observed in site A. Moreover, a naphthalene leak from a tank, into the former industrial area, and a fire broke out near site A, were registered by time-integrated measurements of SPMDs.However, the strong dependence between amount of sequestered PAHs and air temperature needs further studies to distinguish between uptake rate variability and seasonal contribution of different sources. Finally, to measure air concentrations with reasonable accuracy, it should be very important to have certified sampling rates for all individual PAHs.     

Characterization of polycyclic aromatic hydrocarbons deposition in PM2.5 and cloud/fog water at Mount Taishan (China)

Polycyclic aromatic hydrocarbons (PAHs) in PM2.5 and cloud/fog water samples were collected at Mount Taishan in an autumn–winter period, and were analyzed by GS-MS. Higher molecular weight PAHs (4–6 rings) predominated in PM2.5 samples, whereas lighter PAH compounds contributed 61.71% of the total PAH concentration in cloud/fog samples. Particles tended to contain more PAHs and have a more intensive influence on the atmospheric environment on colder days. During cloud/fog events, the scavenging ratio based on PAHs associated with particles was estimated to be about 13.45%. PAHs in PM2.5 samples had a significant positive relationship with CO and SO₂, suggesting that PAHs, SO₂, and CO may originated from the same sources, such as residential coal combustion activities. Diagnostic ratio analysis and factor analysis indicated that the sources of PAHs were mainly from coal combustion during this period.     

Emissions from an automobile fire

The emissions from automobile fires have been investigated. The main gas phase components were analysed in small-scale tests with representative material from an automobile. A more detailed investigation of full-scale simulated automobile fires was also conducted, including the characterisation of gas phase components, particulates and run-off water from extinguishing activities. Three separate full scale fire tests have been characterised: a fire ignited and developed in the engine compartment; a fire ignited inside the coupé, that was extinguished in the early stages; and a similar fire ignited inside the coupé that was allowed to spread until the entire vehicle was involved in the fire. The quantitative analysis of the smoke gases from the full-scale fires showed that emissions with a potentially negative impact on the environment, or chronic toxic effect on humans, were produced in significant quantities. These emissions included HCl, SO2, VOCs (e.g. benzene), PAHs, and PCDDs/PCDFs. Analysis of run-off water indicated that it was severely contaminated, containing elevated levels of both organic compounds and metals. Comparison with data from other vehicle fires found in the literature shows that contamination by lead, copper, zinc, and antimony appears to be significant in water run-off from these types of fires.     

Differences between Weekday and Weekend Air Pollutant Levels in Atlanta; Baltimore; Chicago; Dallas–Fort Worth; Denver; Houston; New York; Phoenix; Washington,DC; and Surrounding Areas

Abstract

We evaluated day-of-week differences in mean concentrations of ozone (O₃) precursors (nitric oxide [NO], nitrogen oxides [NO_x], carbon moNO_xide [CO], and volatile organic compounds [VOCs]) at monitoring sites in 23 states comprising seven geographic focus areas over the period 1998– 2003. Data for VOC measurements were available for six metropolitan areas in five regions. We used Wednesdays to represent weekdays and Sundays to represent weekends; we also analyzed Saturdays. At many sites, NO, NO_x, and CO mean concentrations decreased at all individual hours from 6:00 a.m. to 3:00 p.m. on Sundays compared with corresponding Wednesday means. Statistically significant (p < 0.01) weekend decreases in ambient concentrations were observed for 92% of NO_x sites, 89% of CO sites, and 23% of VOC sites. Nine-hour (6:00 a.m. to 3:00 p.m.) mean concentrations of NO, NO_x, CO, and VOCs declined by 65, 49, 28, and 19%, respectively, from Wednesdays to Sundays (median site responses). Despite the large reductions in ambient NO_x and moderate reductions in ambient CO and VOC concentrations on weekends, ozone and particulate matter (PM) nitrate did not exhibit large changes from week-days to weekends. The median differences between Wednesday and Sunday mean ozone concentrations at all monitoring sites ranged from 3% higher on Sundays for peak 8-hr concentrations determined from all monitoring days to 3.8% lower on Sundays for peak 1-hr concentrations on extreme-ozone days. Eighty-three percent of the sites did not show statistically significant differences between Wednesday and weekend mean concentrations of peak ozone. Statistically significant weekend ozone decreases occurred at 6% of the sites and significant increases occurred at 11% of the sites. Average PM nitrate concentrations were 2.6% lower on Sundays than on Wednesdays. Statistically significant Sunday PM nitrate decreases occurred at one site and significant increases occurred at seven sites.     

Contribution of sugar-cane harvesting season to atmospheric contamination by polycyclic aromatic hydrocarbons (PAHs) in Araraquara city,Southeast Brazil

In Brazil, sugar-cane crops are burned to facilitate harvesting, and this causes environmental pollution from the large amounts of smoke and soot that are released into the atmosphere. The smoke and soot contain numerous organic compounds such as PAHs. In this study, PM₁₀ and PAH concentrations in the air of Araraquara (SE Brazil, with around 200,000 inhabitants and surrounded by sugar-cane plantations) were determined during the harvest and non-harvest seasons. The sampling strategy included two campaigns in each season, with 20 samples per season. PM₁₀ was collected using a Hi-vol sampler with Teflon? – coated glass fiber filters. PM₁₀ ranged from 41 to 181 μg m^?3 during the harvest season, and from 12 to 47 μg m^?3 during the non-harvest season. The mean total concentration of PAHs was 2.5 ng m^?3 (non-harvest season) and 11.6 ng m^?3 (harvest season). In all sampling periods, the most abundant polycyclic aromatic hydrocarbons were phenanthrene and fluoranthrene, and the least abundant was anthracene. The cluster analysis of the total PAH concentrations for each day of sampling and the corresponding meteorological data suggested that the atmospheric concentration of PAHs was independent of the differences in the weather between the seasons. For both sampling seasons, the statistical treatment (PCA, Varimax rotation and HCA) indicated the presence of vehicle sources (diesel, gasoline, and natural-gas engines); but for the harvest season, the main source was attributed to sugar-cane burning. The data generated by this study indicated the burning of sugar-cane as the main contributor to the high levels of PAHs detected in samples during the sugar-cane harvest season.     

Weekday/Weekend Differences in OH Reactivity with VOCs and CO in Baltimore,Maryland

ABSTRACT

This study compared the first-order frequencies for OH associated with volatile organic compounds (VOCs) and CO (hereafter called OH reactivity with VOCs or CO), the product of the VOC or CO concentration, and their respective k_OH value, on an average weekday with that on an average weekend day at a core urban site in Baltimore, MD. The average daytime concentrations were calculated for each of the 55 available Photochemical Assessment Monitoring Station (PAMS) VOCs using data from the Baltimore site. The data were sorted in descending order to highlight the important species based on concentration. The OH reactivity with VOCs was sorted in descending order to identify the important species based on the magnitude of the OH reactivity. A similar process was followed for the OH reactivity with CO. The contribution of the significant species to the weekday/weekend difference in OH reactivity was examined.

The OH reactivity with C₅H₈ was the largest among the OH reactivity with the PAMS' VOCs and was the same on the weekday and weekend. The weekday/weekend difference in OH reactivity with VOCs was entirely due to differences in concentrations of the anthropogenic VOCs. The OH reactivity with VOCs was 11% larger on the weekday. When OH reactivity with CO was included, the OH reactivity was 13% larger on the weekday.     

Long-range transport episodes of fine particles in southern Finland during 1999–2007

The frequency, strength and sources of long-range transport (LRT) episodes of fine particles (PM_2.5) were studied in southern Finland using air quality monitoring results, backward air mass trajectories, remote sensing of fire hot spots, transport and dispersion modelling of smoke and chemical analysis of particle samples (black carbon, monosaccharide anhydrides, oxalate, succinate, malonate, SO₄^2?, NO₃^?, K⁺ and NH₄⁺). At an urban background site in Helsinki, the daily WHO guideline value (24-h PM_2.5 mean 25 μg m^?3) was exceeded during 1–7 LRT episodes per year in 1999–2007. The 24-h mean maximum concentrations varied between 25 and 49 μg m^?3 during the episodes, which was 3–6 times higher than the local mean concentration (8.7 μg m^?3) in 1999–2007. The highest particle concentrations (max. 1-h mean 163 μg m^?3) and the longest episodes (max. 9 days) were mainly caused by the emissions from open biomass burning, especially during springs and late-summers in 2002 and 2006. During the period 2001–2007, the satellite remote sensing of active fire hot spots and transport and dispersion modelling of smoke indicated that approximately half of the episodes were caused partly by the emissions from wildfires and/or agricultural waste burning in fields in Eastern Europe, especially in Russia, Belarus and Ukraine. Other episodes were mainly caused by the LRT of ordinary anthropogenic pollutants, e.g. from energy production, traffic, industry and wood combustion. During those ‘other episodes’, air masses also arrived from Eastern Europe, including Poland. The highest concentrations of biomass-burning tracers, such as monosaccharide anhydrides (levoglucosan + mannosan + galactosan) and K⁺, were observed during open biomass-burning episodes, but quite high values were also measured during some winter episodes due to wood combustion emissions. Our results indicate that open biomass burning in Eastern Europe causes high fine particle concentration peaks in large areas of Europe almost every year.     

Vertical distribution of polycyclic aromatic hydrocarbons in atmospheric boundary layer of Beijing in winter

Air samples were collected using active samplers at various heights of 8, 15, 32, 47, 65, 80, 102, 120, 140, 160, 180, 200, 240, 280 and 320 m on a meteorological tower in an urban area of Beijing in two campaigns in winter 2006. Altitudinal distributions of polycyclic aromatic hydrocarbons (PAHs) in atmospheric boundary layer of Beijing in winter season were investigated. Meteorological conditions during the studied period were characterized by online measurements of four meteorological parameters as well as trajectory calculation. The mean total concentrations of 15 PAHs except naphthalene of gaseous and particulate phase were 667±450 and 331±144 ng m⁻³ in January and 61±19 and 29±6 ng m⁻³ in March, respectively. Domestic coal combustion and vehicle emission were the dominant PAH sources in winter. Although the composition profiles derived from the two campaigns were similar, the concentrations were different by one order of magnitude. The higher concentrations in January were partly caused by higher emission due to colder weather than March. Moreover, weak wind, passing through the city center before the sampling site, picked up more contaminants on the way and provided unfavorable dispersion condition in January. For both campaigns, PAH concentrations decreased with heights because of ground-level emission and unfavorable dispersion conditions in winter. The concentration ratio of PAHs in gas versus solid phases was temperature dependent and negatively correlated to their octanol–air partition coefficients.     

Sources and seasonal variation of atmospheric polycyclic aromatic hydrocarbons in Dalian,China: Factor analysis with non-negative constraints combined with local source fingerprints

Vapor- and particulate-phase polycyclic aromatic hydrocarbon (PAH) samples were continuously collected at an urban site in Dalian, China, during the heating and non-heating period. There is strong temperature dependence and obvious seasonal trend for atmospheric PAHs, and significant positive correlations of atmospheric PAHs with SO₂ and CO concentrations were observed. Factor analysis model with non-negative constraints (FA–NNC) combined with local and literature PAH source fingerprints was successful in source identification of particulate PAHs in the atmospheric samples. The results suggested that, in heating period, the main pollution sources were identified as coal-fired boiler emission (56%), residential coal combustion (33%) and traffic emissions (11%). As for non-heating period, the main sources were gasoline engine emission, traffic tunnel emission and coal-fired power plant, and the overall source contributions of traffic emission (gasoline engine + traffic tunnel) were 79% and coal-fired power plant 21%. The current results support our previous study and provide new insights. This can be the first attempt to quantitatively apportion air organic pollutants using receptor models combined with local source fingerprints. The source fingerprints can be used as reference data for source apportionment of atmospheric PAHs of China.     

Quantitative analysis of volatile organic compounds (VOCs) in atmospheric particles

There are a number of difficulties associated with the quantitative analysis of volatile organic compounds (VOCs) in atmospheric particles. Therefore, majority of the previous studies on VOCs associated with particles have been qualitative. Air samples were collected in Izmir, Turkey to determine ambient particle and gas phase concentrations of several aromatic, oxygenated and halogenated VOCs. Samples were quantitatively analyzed using thermal desorption–gas chromatography/mass spectrometry. Gas-phase concentrations ranged between 0.02 (bromoform) and 4.65 μg m⁻³ (toluene) and were similar to those previously measured at the same site. Particle-phase concentrations ranged from 1 (1,3-dichlorobenzene) to 933 pg m⁻³ (butanol). VOCs were mostly found in gas-phase (99.9±0.25%). However, the particulate VOCs had comparable concentrations to those reported previously for semivolatile organic compounds. The distribution of particle-phase VOCs between fine (d_p<2.5 μm) and coarse (2.5 μm<d_p<10 μm) fractions was also investigated. It was found that VOCs were mostly associated with fine particles.     

Measurement of the vertical profile of atmospheric SO2 during the heating period in Beijing on days of high air pollution

This paper reports altitude-resolved concentrations of sulfur dioxide (SO₂) and particulate matter up to 10 microns in diameter (PM₁₀) in the planetary boundary layer of major urban centers during extreme pollution episodes. The concentration of SO₂ was observed continuously from November 24, 2004, to December 4, 2004, in Beijing during the heating period. Fluorescence SO₂ analyzers were used to measure the atmospheric SO₂ concentrations. Four SO₂ analyzers were placed at 4 different levels (8 m, 47 m, 120 m, and 280 m) of the 325-m high meteorological observation tower of the Institute of Atmospheric Physics (IAP), Chinese Academy of Sciences. A maximal SO₂ concentration of 172.3 ppb was measured during this pollution episode, and SO₂ concentration increased with altitude and reached its maximal value at ～50 m. The study also analyzed the meteorological situation before, during, and after the pollution episode.     

Control of Ozone Precursors in a Complex Industrial Terrain by Using Multiscale-Nested Air Quality Models with Fine Spatial Resolution (1 km2)

Abstract

The location of the northeastern Iberian Peninsula (NEIP) in the northwestern Mediterranean basin, the presence of the Pyrenees mountain range (with altitudes >3000 m), and the influence of the Mediterranean Sea and the large valley canalization of Ebro river induce an extremely complicated structure for the dispersion of photochemical pollutants. Air pollution studies in very complex terrains such as the NEIP require high-resolution modeling for resolving the very complex dynamics of flows. To deal with the influence of larger-scale transport, however, high-resolution models have to be nested in larger models to generate appropriate initial and boundary conditions for the finer resolution domains. This article shows the results obtained through the utilization of the MM5-EMICAT2000-CMAQ multiscale-nested air quality model relating the sensitivity regimes for ozone (O₃)-nitrogen oxides (NO_x)-volatile organic compounds (VOCs) in an area of high geographical complexity, like the industrial area of Tarragona, located in the NEIP. The model was applied with fine temporal (one-hour) and spatial resolution (cells of 24 km, 2 km, and 1 km) to represent the chemistry and transport of tropospheric O₃ and other photochemical species with respect to different hypothetical scenarios of emission controls and to quantify the influence of different emission sources in the area. Results indicate that O₃ chemistry in the industrial domain of Tarragona is strongly sensitive to VOCs; the higher percentages of reduction for ground-level O₃ are achieved when reducing by 25% the emissions of industrial VOCs. On the contrary, reductions in the industrial emissions of NO_x contribute to a strong increase in hourly peak levels of O₃. At the same time, the contribution of on-road traffic and biogenic emissions to ground-level O₃ concentrations in the area is negligible with respect to the pervasive weight of industrial sources. This analysis provides an assessment of the effectiveness of different policies for the control of emission of precursors by comparing the modeled results for different scenarios.     

Anomalous high ozone concentrations recorded at a high mountain station in Italy in summer 2003

In order to evaluate the possible effects of heatwave phenomena on background O₃ concentrations, the average summer O₃ concentrations at the high mountain station of Mt. Cimone (MTC—2165 m a.s.l.) have been analyzed. In particular, at this baseline station unusually high O₃ concentrations were recorded during August 2003, when an intense heatwave (the “August heatwave”) affected Europe. During this heatwave, the highest O₃ concentrations were recorded at MTC in connection with air masses coming from continental Europe and the Po basin boundary layer as shown by three-dimensional air mass back-trajectory and mixing height analyzes. However, high O₃ concentrations were also recorded in air masses coming from the middle troposphere (above 3000 m a.s.l.), thus suggesting the presence of O₃-rich atmospheric layers over Europe. This could be due to the large extension of the mixing layer which favoured the transport of high concentrations of O₃ and its precursors to altitudes that would usually be in the free troposphere. Other than from traffic and industrial activities, a contribution to the high O₃ concentrations recorded at MTC during the August heatwave could derive from fires in the North of Italy, as suggested by a well-documented episode and supported by in situ CO₂ measurements used as non-conventional tracer for fire emissions.     

PAH air pollution at a Portuguese urban area: carcinogenic risks and sources identification

This study aimed to characterize air pollution and the associated carcinogenic risks of polycyclic aromatic hydrocarbon (PAHs) at an urban site, to identify possible emission sources of PAHs using several statistical methodologies, and to analyze the influence of other air pollutants and meteorological variables on PAH concentrations.The air quality and meteorological data were collected in Oporto, the second largest city of Portugal. Eighteen PAHs (the 16 PAHs considered by United States Environment Protection Agency (USEPA) as priority pollutants, dibenzo[a,l]pyrene, and benzo[j]fluoranthene) were collected daily for 24 h in air (gas phase and in particles) during 40 consecutive days in November and December 2008 by constant low-flow samplers and using polytetrafluoroethylene (PTFE) membrane filters for particulate (PM₁₀ and PM_2.5 bound) PAHs and pre-cleaned polyurethane foam plugs for gaseous compounds. The other monitored air pollutants were SO₂, PM₁₀, NO₂, CO, and O₃; the meteorological variables were temperature, relative humidity, wind speed, total precipitation, and solar radiation. Benzo[a]pyrene reached a mean concentration of 2.02 ng?m^?3, surpassing the EU annual limit value. The target carcinogenic risks were equal than the health-based guideline level set by USEPA (10^?6) at the studied site, with the cancer risks of eight PAHs reaching senior levels of 9.98?×?10^?7 in PM₁₀ and 1.06?×?10^?6 in air. The applied statistical methods, correlation matrix, cluster analysis, and principal component analysis, were in agreement in the grouping of the PAHs. The groups were formed according to their chemical structure (number of rings), phase distribution, and emission sources. PAH diagnostic ratios were also calculated to evaluate the main emission sources. Diesel vehicular emissions were the major source of PAHs at the studied site. Besides that source, emissions from residential heating and oil refinery were identified to contribute to PAH levels at the respective area. Additionally, principal component regression indicated that SO₂, NO₂, PM₁₀, CO, and solar radiation had positive correlation with PAHs concentrations, while O₃, temperature, relative humidity, and wind speed were negatively correlated.     

Very high weight ratios of S/K in individual haze particles over Kalimantan during the 1997 Indonesian forest fires

The elemental composition of individual aerosol particles of 0.15–3 μm radius, collected over Kalimantan during the 1997 Indonesian forest fire event, was analyzed using a transmission electron microscope equipped with an energy-dispersive X-ray analyzer (EDX). Although 60–90% of the particles collected at altitudes of 1–5 km contained K, they exhibited high weight ratios of S/K with median values of 9–18 independent of particle size. These were much larger than those (median values of 2–4) obtained from the forest fires in northern Australia. The high weight ratios over Kalimantan are considered to be due to the heterogeneous growth of particles through the oxidation of SO₂. In addition to SO₂ from the combustion of forest biomass, SO₂ originating from the combustion of peat below the ground is believed to have been important in producing the high S/K ratios.     

PM2.5 and PM10: The influence of sugarcane burning on potential cancer risk

In Brazil, sugarcane fields are often burned to facilitate manual harvesting, and this burning causes environmental pollution from the large amounts of soot released into the atmosphere. This material contains numerous organic compounds such as PAHs. In this study, the concentrations of PAHs in two particulate-matter fractions (PM_2.5 and PM₁₀) in the city of Araraquara (SE Brazil, with around 200,000 inhabitants and surrounded by sugarcane plantations) were determined during the sugarcane harvest (HV) and non-harvest (NHV) seasons in 2008 and 2009. The sampling strategy included four campaigns, with 60 samples in the NHV season and 220 samples in the HV season. The PM_2.5 and PM₁₀ fractions were collected using a dichotomous sampler (10 L min^?1, 24 h) with Teflon? filters. The filter sets were extracted (ultrasonic bath with hexane/acetone (1:1 v/v)) and analyzed by HPLC/Fluorescence. The median concentration for total PAHs (PM_2.5 in 2009) was 0.99 ng m^?3 (NHV) and 3.3 ng m^?3 (HV). In the HV season, the total concentration of carcinogenic PAHs (benz(a)anthracene, benzo(b)fluoranthene, benzo(k)fluoranthene, and benzo(a)pyrene) was 5 times higher than in the NHV season. B(a)P median concentrations were 0.017 ng m^?3 and 0.12 ng m^?3 for the NHV and HV seasons, respectively. The potential cancer risk associated with exposure through inhalation of these compounds was estimated based on the benzo[a]pyrene toxic equivalence (BaP_eq), where the overall toxicity of a PAH mixture is defined by the concentration of each compound multiplied by its relative toxic equivalence factor (TEF). BaP_eq median (2008 and 2009 years) ranged between 0.65 and 1.0 ng m^?3 and 1.2–1.4 ng m^?3 for the NHV and HV seasons, respectively. Considering that the maximum permissible BaP_eq in ambient air is 1 ng m^?3, related to the increased carcinogenic risk, our data suggest that the level of human exposure to PAHs in cities surrounded by sugarcane crops where the burning process is used is cause for concern.