Adaptation of a speciation sampling cartridge for measuring ammonia flux from cattle feedlots using relaxed eddy accumulation

Improved measurements of ammonia losses from cattle feedlots are needed to quantify the national NH₃ emissions inventory and evaluate management techniques for reducing emissions. Speciation cartridges composed of glass honeycomb denuders and filter packs were adapted to measure gaseous NH₃ and aerosol NH₄⁺ fluxes using relaxed eddy accumulation (REA). Laboratory testing showed that a cartridge equipped with four honeycomb denuders had a total capture capacity of 1800 μg of NH₃. In the field, a pair of cartridges was deployed adjacent to a sonic anemometer and an open-path gas analyzer on a mobile tower. High-speed valves were attached to the inlets of the cartridges and controlled by a datalogger so that up- and down-moving eddies were independently sampled based on direction of the vertical wind speed and a user-defined deadband. Air flowed continuously through the cartridges even when not sampling by means of a recirculating air handling system. Eddy covariance measurement of CO₂ and H₂O, as measured by the sonic and open-path gas analyzer, were used to determine the relaxation factor needed to compute REA-based fluxes. The REA system was field tested at the Beef Research Unit at Kansas State University in the summer and fall of 2007. Daytime NH₃ emissions ranged between 68 and 127 μg m^?2 s^?1; fluxes tended to follow a diurnal pattern correlated with latent heat flux. Daily fluxes of NH₃ were between 2.5 and 4.7 g m^?2 d^?1 and on average represented 38% of fed nitrogen. Aerosol NH₄⁺ fluxes were negligible compared with NH₃ emissions. An REA system designed around the high-capacity speciation cartridges can be used to measure NH₃ fluxes from cattle feedlots and other strong sources. The system could be adapted to measure fluxes of other gases and aerosols.     

Size partitioning of particulate inorganic nitrogen species between the fine and coarse mode ranges and its implication to their deposition on the surface ocean

In order to discuss the dry deposition fluxes of atmospheric fixed nitrogen species, observations of aerosol chemistry including nitrate (NO₃^?) and ammonium (NH₄⁺) were conducted at two islands, Rishiri Island and Sado Island, over the Sea of Japan. Although the atmospheric concentrations of particulate NH₄⁺–N showed higher values than those of particulate NO₃^?–N at both sites, the dry deposition fluxes of the particulate NO₃^?–N were estimated to be higher than those of the particulate NH₄⁺–N. This was caused by the difference of particle sizes between the particulate NO₃^? and NH₄⁺; NH₄⁺ was almost totally contained in fine particles (d < 2.5 μm) with smaller deposition velocity, whereas NO₃^? was mainly contained in coarse particles (d > 2.5 μm) with greater deposition velocity. Fine mode NO₃^? was strongly associated with fine mode sea-salt and mineral particles, of which higher concentrations shifted the size of particulate NO₃^? toward the fine mode range. This size shift would decrease the dry deposition flux of the fixed nitrogen species on coastal waters and accelerate atmospheric transport of them to the remote oceanic areas.     

Deposition rates on smooth surfaces and coagulation of aerosol particles inside a test chamber

Because aerosol particle deposition is an important factor in indoor air quality, many empirical and theoretical studies have attempted to understand the process. In this study, we estimated the deposition rate of aerosol particles on smooth aluminum surfaces inside a test chamber. We investigated the influence of turbulent intensity due to ventilation and fan operation. We also investigated two important processes in particle deposition: turbophoresis, which is significant for micron particles, and coagulation, which is relevant to ultrafine particles (UFP diameter <0.1 μm) at high particle concentrations. Our analysis included semi-empirical estimates of the deposition rates that were compared to available deposition models and verified with simulations of an aerosol dynamics model. In agreement with previous studies, this study found that induced turbulent intensity greatly enhanced deposition rates of fine particles (FP diameter <1 μm). The deposition rate of FP was proportional to the ventilation rate, and it increased monotonically with fan speed. With our setup, turbophoresis was very important for coarse particles larger than 5 μm. The coagulation of aerosol particles was insignificant when the particle concentration was less than 10⁴ cm^?3 during fan operation. The model simulation results verified that the aerosol dynamics module incorporated in our Multi-Compartment and Size-Resolved Indoor Aerosol Model (MC-SIAM) was valid. The behavior of aerosol particles inside our chamber was similar to that found in real-life conditions with the same ventilation rates (0.018–0.39 h^?1) and similar air mixing modes. Therefore, our findings provide insight into indoor particle behavior.     

Isoprene and monoterpene fluxes measured above Amazonian rainforest and their dependence on light and temperature

Canopy scale emissions of isoprene and monoterpenes from Amazonian rainforest were measured by eddy covariance and eddy accumulation techniques. The peak mixing ratios at about 10 m above the canopy occurred in the afternoon and were typically about 90 ppt_v of α-pinene and 4–5 ppb_v of isoprene. α-pinene was the most abundant monoterpene in the air above the canopy comprising ≈50% of the total monoterpene mixing ratio. Measured isoprene fluxes were almost 10 times higher than α-pinene fluxes. Normalized conditions of 30°C and 1000 μmol m⁻² s⁻¹ were associated with an isoprene flux of 2.4 mg m⁻² h⁻¹ and a β-pinene flux of 0.26 mg m⁻² h⁻¹. Both fluxes were lower than values that have been specified for Amazon rainforests in global emission models. Isoprene flux correlated with a light- and temperature-dependent emission activity factor, and even better with measured sensible heat flux. The variation in the measured α-pinene fluxes, as well as the diurnal cycle of mixing ratio, suggest emissions that are dependent on both light and temperature. The light and temperature dependence can have a significant effect on the modeled diurnal cycle of monoterpene emission as well as on the total monoterpene emission.     

Secondary organic aerosol importance in the future atmosphere

In order to investigate the secondary organic aerosol (SOA) response to changes in biogenic volatile organic compounds (VOC) emissions in the future atmosphere and how important will SOA be relative to the major anthropogenic aerosol component (sulfate), the global three-dimensional chemistry/transport model TM3 has been used. Emission estimates of biogenic VOC (BVOC) and anthropogenic gases and particles from the literature for the year 2100 have been adopted.According to our present-day model simulations, isoprene oxidation produces 4.6 Tg SOA yr⁻¹, that is less than half of the 12.2 Tg SOA yr⁻¹ formed by the oxidation of other BVOC. In the future, nitrate radicals and ozone become more important than nowadays, but remain minor oxidants for both isoprene and aromatics. SOA produced by isoprene is estimated to almost triple, whereas the production from other BVOC more than triples. The calculated future SOA burden change, from 0.8 Tg at present to 2.0 Tg in the future, is driven by changes in emissions, oxidant levels and pre-existing particles. The non-linearity in SOA formation and the involved chemical and physical feedbacks prohibit the quantitative attribution of the computed changes to the above-mentioned individual factors. In 2100, SOA burden is calculated to exceed that of sulfate, indicating that SOA might become more important than nowadays. These results critically depend on the biogenic emissions and thus are subject to the high uncertainty associated with these emissions estimated due to the insufficient knowledge on plant response to carbon dioxide changes. Nevertheless, they clearly indicate that the change in oxidants and primary aerosol caused by human activities can contribute as much as the change in BVOC emissions to the increase of the biogenic SOA production in the future atmosphere.     

Coarse and fine aerosol source apportionment in Rio de Janeiro,Brazil

The metropolitan area of Rio de Janeiro is one of the twenty biggest urban agglomerations in the world, with 11 million inhabitants in the metropolitan area, and has a high population density, with 1700 hab. km^?2. For this aerosol source apportionment study, the atmospheric aerosol sampling was performed at ten sites distributed in different locations of the metropolitan area from September/2003 to December/2005, with sampling during 24 h on a weekly basis. Stacked filter units (SFU) were used to collect fine and coarse aerosol particles with a flow rate of 17 L min^?1. In both size fractions trace elements were analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) as well as water-soluble species by Ion-Chromatography (IC). Also gravimetric analysis and reflectance measurements provided aerosol mass and black carbon concentrations. Very good detection limits for up to 42 species were obtained. Mean annual PM₁₀ mass concentration ranged from 20 to 37 μg m^?3, values that are within the Brazilian air quality standards. Receptor models such as principal factor analysis, cluster analysis and absolute principal factor analysis were applied in order to identify and quantify the aerosol sources. For fine and coarse modes, circa of 100% of the measured mass was quantitatively apportioned to relatively few identified aerosol sources. A very similar and consistent source apportionment was obtained for both fine and coarse modes for all 10 sampling sites. Soil dust is an important component, accounting for 22–72% and for 25–48% of the coarse and fine mass respectively. On the other hand, anthropogenic sources as vehicle traffic and oil combustion represent a relatively high contribution (52–75%) of the fine aerosol mass. The joint use of ICP-MS and IC analysis of species in aerosols has proven to be reliable and feasible for the analysis of large amount of samples, and the coupling with receptor models provided an excellent method for quantitative aerosol source apportionment in large urban areas.     

Sensitivity of shortwave radiative fluxes to the vertical distribution of aerosol single scattering albedo in the presence of a desert dust layer

The aim of this work is to quantify the sensitivity of shortwave radiative fluxes to changes in the vertical distribution of aerosol absorption, taken into account through the aerosol Single Scattering Albedo (SSA). The case study represents a real atmospheric situation with a desert dust layer (DDL) in the mid troposphere over an urban Boundary Layer (BL) observed at Rome on 20 June 2007. A moderately high aerosol optical depth (AOD), 0.292 at 550 nm, and low Ångström exponent of 0.30 were measured. The observed case was reconstructed with a radiative transfer model, in which the SSA of the boundary layer aerosols was varied from that of a highly absorbing aerosol type (urban) to a highly scattering one (clear marine). The SSA of the DDL is determined keeping fixed the measured SSA of the whole atmospheric column. The simulations show notable changes in the surface and top of the atmosphere (TOA) diffuse fluxes depending on the boundary layer aerosol properties. The aerosol radiative forcing (ARF) at the surface changes by 6–19 W m^?2, depending on the solar zenith angle, when urban or clean marine particles are included in the boundary layer. The ARF differences observed at TOA are between 1 and 5 W m^?2 when urban and clean marine aerosol types in the BL are respectively used, showing a smaller dependency on the solar zenith angle than at the surface.     

Link between aerosol optical,microphysical and chemical measurements in an underground railway station in Paris

Measurements carried out in Paris Magenta railway station in April–May 2006 underlined a repeatable diurnal cycle of aerosol concentrations and optical properties. The average daytime PM₁₀ and PM_2.5 concentrations in such a confined space were approximately 5–30 times higher than those measured in Paris streets. Particles are mainly constituted of dust, with high concentrations of iron and other metals, but are also composed of black and organic carbon. Aerosol levels are linked to the rate at which rain and people pass through the station. Concentrations are also influenced by ambient air from the nearby streets through tunnel ventilation. During daytime approximately 70% of aerosol mass concentrations are governed by coarse absorbing particles with a low Angström exponent (～0.8) and a low single-scattering albedo (～0.7). The corresponding aerosol density is about 2 g cm^?3 and their complex refractive index at 355 nm is close to 1.56–0.035 i. The high absorption properties are linked to the significant proportion of iron oxides together with black carbon in braking systems. During the night, particles are mostly submicronic, thus presenting a greater Angström exponent (～2). The aerosol density is lower (1.8 g cm^?3) and their complex refractive index presents a lower imaginary part (1.58–0.013 i), associated to a stronger single-scattering albedo (～0.85–0.90), mostly influenced by the ambient air. For the first time we have assessed the emission (deposition) rates in an underground station for PM₁₀, PM_2.5 and black carbon concentrations to be 3314 ± 781(?1164 ± 160), 1186 ± 358(?401 ± 66) and 167 ± 46(?25 ± 9) μg m^?2 h^?1, respectively.     

Atmospheric nitrogen fluxes at the Belgian coast: 2004–2006

Daily and seasonal variations in dry and wet atmospheric nitrogen fluxes have been studied during four campaigns between 2004 and 2006 at a coastal site of the Southern North Sea at De Haan (Belgium) located at coordinates of 51.1723° N and 3.0369° E. Concentrations of inorganic N-compounds were determined in the gaseous phase, size-segregated aerosol (coarse, medium, and fine), and rainwater samples. Dissolved organic nitrogen (DON) was quantified in rainwater. The daily variations in N-fluxes of compounds were evaluated with air-mass backward trajectories, classified into the main air-masses arriving at the sampling site (i.e., continental, North Sea, and Atlantic/UK/Channel).The three, non-episodic campaigns showed broadly consistent fluxes, but during the late summer campaign exceptionally high episodic N-deposition was observed. The average dry and wet fluxes for non-episodic campaigns amounted to 2.6 and 4.0 mg N m^?2 d^?1, respectively, whereas during the episodic late summer period these fluxes were as high as 5.2 and 6.2 mg N m^?2 d^?1, respectively.Non-episodic seasons/campaigns experienced average aerosol fluxes of 0.9–1.4 mg N m^?2 d^?1. Generally, the contribution of aerosol NH₄⁺ was more significant in the medium and fine particulate fractions than that of aerosol NO₃^?, whereas the latter contributed more in the coarse fraction, especially in continental air-masses. During the dry mid-summer campaign, the DON contributed considerably (～15%) to the total N-budget.Exceptionally high episodic aerosol-N inputs have been observed for the late summer campaign, with especially high deposition rates of 3.6 and 2.9 mg N m^?2 d^?1 for Atlantic/UK/Channel and North Sea-continental (mixed) air-masses, respectively. During this pollution episode, the flux of NH₄⁺ was dominating in each aerosol fraction/air-mass, except for coarse continental aerosols. High deposition of gaseous-N was also observed in this campaign with an average total N-flux of 2–2.5-times higher than in other campaigns.     

Direct measurements and parameterisation of aerosol flux,concentration and emission velocity above a city

Articles have recently been published on aerosol size distributions and number concentrations in cities, however there have been no studies on transport of these particles. Eddy covariance measurements of vertical transport of aerosol in the size range 11 nm<D_p<3 μm are presented here. The analysis shows that typical average aerosol number fluxes in this size range vary between 9000 and 90,000 cm⁻² s⁻¹. With concentrations between 3000 and 20,000 cm⁻³ this leads to estimates of particle emission velocity between 20 and 75 mm s⁻¹. The relationships between number flux and traffic activity, along with emission velocity and boundary layer stability are demonstrated and parameterised. These are used to derive an empirical parameterisation for aerosol concentration in terms of traffic activity and stability. The main processes determining urban aerosol fluxes and concentrations are discussed and quantified where possible. The difficulties in parameterising urban activity are discussed.     

Seasonal characteristics of water-soluble organic carbon in atmospheric particles in the inland Kanto plain,Japan

An investigation of water-soluble organic carbon (WSOC) in atmospheric particles was conducted as an index of the formation of secondary organic aerosol (SOA) from April 2005 to March 2006 at Maebashi and Akagi located in the inland Kanto plain in Japan. Fine (<2.1 μm) and coarse (2.1–11 μm) particles were collected by using an Andersen low-volume air sampler, and WSOC, organic carbon (OC), elemental carbon (EC), and ionic components were measured. The mean mass concentrations of the fine particles were 22.2 and 10.5 μg m^?3 at Maebashi and Akagi, respectively. The WSOC in fine particles accounted for a large proportion (83%) of total WSOC. The concentration of fine WSOC ranged from 1.2 to 3.5 μg-C m^?3 at Maebashi, rising from summer to fall. At Akagi, it rose from spring to summer, associated with the southerly wind from urban areas. The WSOC/OC ratio increased in summer at both sites, but the ratio at Akagi was higher, which we attributed to differences in primary emissions and secondary formation between the sites. The fine WSOC concentration was significantly positively correlated with concentrations of SO₄^2?, EC, and K⁺, and we inferred that WSOC was produced by photochemical reaction and caused by the combustion of both fuel and biomass. We estimated that SOA accounted for 11–30% of the fine particle mass concentration in this study, suggesting that SOA is a significant year-round component in fine particles.     

Ozone uptake by citrus trees exposed to a range of ozone concentrations

The Citrus genus includes a large number of species and varieties widely cultivated in the Central Valley of California and in many other countries having similar Mediterranean climates. In the summer, orchards in California experience high levels of tropospheric ozone, formed by reactions of volatile organic compounds (VOC) with oxides of nitrogen (NO_x). Citrus trees may improve air quality in the orchard environment by taking up ozone through stomatal and non-stomatal mechanisms, but they may ultimately be detrimental to regional air quality by emitting biogenic VOC (BVOC) that oxidize to form ozone and secondary organic aerosol downwind of the site of emission. BVOC also play a key role in removing ozone through gas-phase chemical reactions in the intercellular spaces of the leaves and in ambient air outside the plants. Ozone is known to oxidize leaf tissues after entering stomata, resulting in decreased carbon assimilation and crop yield. To characterize ozone deposition and BVOC emissions for lemon (Citrus limon), mandarin (Citrus reticulata), and orange (Citrus sinensis), we designed branch enclosures that allowed direct measurement of fluxes under different physiological conditions in a controlled greenhouse environment. Average ozone uptake was up to 11 nmol s^?1 m^?2 of leaf. At low concentrations of ozone (40 ppb), measured ozone deposition was higher than expected ozone deposition modeled on the basis of stomatal aperture and ozone concentration. Our results were in better agreement with modeled values when we included non-stomatal ozone loss by reaction with gas-phase BVOC emitted from the citrus plants. At high ozone concentrations (160 ppb), the measured ozone deposition was lower than modeled, and we speculate that this indicates ozone accumulation in the leaf mesophyll.     

Correlation between PM concentrations and aerosol optical depth in eastern China

Using one year of Aerosol Optical Depth (AOD) derived from Moderate Resolution Imaging Spectroradiometer (MODIS) on the Terra satellite and particular matter (PM) contents measured at eleven sites located mostly in the eastern China in 2007, the relationship between columnar AOD and hourly and daily average (DA) PM were established. The peak AOD observed from MODIS was generally consistent with the surface PM measurements in eastern China, where Zhengzhou had the maximum annual mean PM₁₀ of 182.1 μg m^?3, while Longfengshan had the minimum annual mean of 38.1 μg m^?3. Ground level observations indicated that PM concentration varies widely across different regions, which was mainly due to the difference in weather conditions and anthropogenic emissions. The coarse particles accounted for the main air pollution in Zhengzhou and Benxi whiles the fine particles, however, were the main constituents in other sites. Results showed that MODIS AOD (averaged over the box of 5 × 5 and 3 × 3 pixels) had a better positive correlation with the coincident hourly average (HA) PM concentration than with DA due to diurnal variation in PM mass measurements. After correcting AOD for relative humidity (RH), the correlation did not improve significantly, suggesting that the RH was not the main factor affecting the correlation of PM with AOD. The statistical regression analysis between MODIS AOD and PM mass suggested that the satellite-derived AOD is a useful tool for mapping PM distribution over large spatial domains.     

Carbon dioxide fluxes over an urban park area

From September 2006 to October 2007 turbulent fluxes of carbon dioxide were measured at an urban tower station (26 m above ground level, z/z_h = 1.73) in Essen, Germany, using the eddy covariance technique. The site was located at the border between a public park area (70 ha) in the south–west of the station and suburban/urban residential as well as light commercial areas in the north and east of the tower. Depending on the land-use two different sectors (park and urban) were identified showing distinct differences in the temporal evolution of the surface-atmosphere exchange of CO₂. While urban fluxes appear to be governed by anthropogenic emissions from domestic heating and traffic (average flux 9.3 μmol m^?2 s^?1), the exchange of CO₂ was steered by biological processes when the park contributed to the flux footprint. The diurnal course during the vegetation period exhibited negative daytime fluxes up to ?10 μmol m^?2 s^?1 on average in summer. Nevertheless, with a mean of 0.8 μmol m^?2 s^?1 park sector fluxes were slightly positive, thus no net carbon uptake by the surface occurred throughout the year.In order to sum the transport of CO₂ a gap-filling procedure was performed by means of artificial neural network generalisation. Using additional meteorological inputs the daily exchange of CO₂ was reproduced using radial basis function networks (RBF). The resulting yearly sum of 6031 g m^?2 a^?1 indicates the entire study site to be a considerable source of CO₂.     

Atmospheric phosphorus deposition at a montane site: Size distribution,effects of wildfire,and ecological implications

The dry deposition of atmospheric particulate matter can be a significant source of phosphorus (P) to oligotrophic aquatic ecosystems, including high-elevation lakes. In this study, measurements of the mass concentration and size distribution of aerosol particles and associated particulate P are reported for the southern Sierra Nevada, California, for the period July–October, 2008. Coarse and fine particle samples were collected with Stacked Filter Units and analyzed for Total P (TP) and inorganic P (IP) using a digestion-extraction procedure, with organic P (OP) calculated by difference. Particle size-resolved mass and TP distributions were determined concurrently using a MOUDI cascade impactor. Aerosol mass concentrations were significantly elevated at the study site, primarily due to transport from offsite and emissions from local and regional wildfires. Atmospheric TP concentrations ranged from 11 to 75 ng m^?3 (mean = 37 ± 16 ng m^?3), and were typically dominated by IP. Phosphorus was concentrated in the coarse (>1 μm diameter) particle fraction and was particularly enriched in the 1.0–3.2 μm size range, which accounted for 30–60% of the atmospheric TP load. Wildfire emissions varied widely in P content, and may be related to fire intensity. The estimated dry depositional flux of TP for each daily sampling period ranged between 7 and 118 μg m^?2 d^?1, with a mean value of 40 ± 27 μg m^?2 d^?1. Relative rates of dry deposition of N and P in the Sierra Nevada are consistent with increasing incidence of N limitation of phytoplankton growth and previously observed long-term eutrophication of lakes.     

Aerosol size and chemical characteristics at Mumbai,India, during the INDOEX-IFP (1999)

Aerosol size and chemical characteristics govern their optical and radiative effects and their potential for cloud nucleation. This paper reports the size and chemical characteristics of surface aerosols measured at Mumbai during the Indian Ocean Experiment-Intensive Field Phase (INDOEX-IFP), January–March 1999. Carbonaceous (30%) and ionic (20%) constituents contributed significantly to aerosol mass. High black carbon concentrations and a low organic to black carbon ratio implied the predominance of primary carbonaceous aerosol, while a high nss-sulphate contribution in the fine mode, suggested a probable anthropogenic origin. Non-sea-salt potassium (nss-K⁺) and black carbon concentrations correlated during January and early February, with nss-K⁺ in the fine mode contributing 86% of total-K⁺, implying a common origin from a local biomass-burning source. Crustal sources were dominant during late-February and March, with 69% of the aerosol mass present in the coarse mode, and 60% of the variation in PM-10 measured during 12:00–16:00 h being explained by a crustal source factor. Chloride depletion was estimated throughout the study, more significantly during January and early February, from the higher RH and lower Ca²⁺/Na²⁺ ratios. A negative correlation was obtained of chloride with nitrate, indicating probable nitrate substitution. During late-February and March, nitrate correlated with calcium suggesting an association with soil. Nss-sulphate correlated with calcium but not sodium, implying a probable association with crustal aerosols.     

Optical Measurements of Aerosol Size Distributions in Great Smoky Mountains National Park: Dry Aerosol Characterization

ABSTRACT

Aerosol size distributions were measured during the summertime 1995 Southeastern Aerosol and Visibility Study (SEAVS) in Great Smoky Mountains National Park using an Active Scattering Aerosol Spectrometer (ASASP-X) optical particle counter. We present an overview of the experimental method, our data inversion technique, timelines of the size distribution parameters, and calculations of dry accumulation mode aerosol density and refractive index. Aerosol size distributions were recorded during daylight hours for aerosol in the size range 0.1 < Dp < 2.5 u,m. The particle refractive index used for the data inversion was calculated with the partial molar refractive index approach using 12-hr measured aerosol chemical composition. Aerosol accumulation mode volume concentrations ranging from 1 to 26 u,m³ cm^-3 were observed, with an average of 7 ± 5 u,m³ cm^-3. The study average dry accumulation mode geometric volume median diameter was 0.27 ± 0.03 u,m, and the mean geometric standard deviation was 1.45 ± 0.06. Using an internally mixed aerosol model, and assuming chemical homogeneity across the measured particle distribution, an average accumulation mode dry sulfate ion mass scattering efficiency of 3.8 ± 0.6 m² g^-1 was calculated.     

Aerosol speciation and mass prediction from toluene oxidation under high NOx conditions

A kinetically based gas-particle partitioning box model is used to highlight the importance of parameter representation in the prediction of secondary organic aerosol (SOA) formation following the photo-oxidation of toluene. The model is initialized using experimental data from York University's indoor smog chamber and provides a prediction of the total aerosol yield and speciation. A series of model sensitivity experiments were performed to study the aerosol speciation and mass prediction under high NO_x conditions (VOC/NO_x = 0.2). Sensitivity experiments indicate vapour pressure estimation to be a large area of weakness in predicting aerosol mass, creating an average total error range of 70 μg m^?3 (range of 5–145 μg m^?3), using two different estimation methods. Aerosol speciation proved relatively insensitive to changes in vapour pressure. One species, 3-methyl-6-nitro-catechol, dominated the aerosol phase regardless of the vapour pressure parameterization used and comprised 73–88% of the aerosol by mass. The dominance is associated with the large concentration of 3-methyl-6-nitro-catechol in the gas-phase. The high NO_x initial conditions of this study suggests that the predominance of 3-methyl-6-nitro-catechol likely results from the cresol-forming branch in the Master Chemical Mechanism taking a significant role in secondary organic aerosol formation under high NO_x conditions. Further research into the yields and speciation leading to this reaction product is recommended.     

Experimental evidence for a significant contribution of cellulose to indoor aerosol mass concentration

An apartment bedroom located in a residential area of Aveiro (Portugal) was selected with the aim of characterizing the cellulose content of indoor aerosol particles. Two sets of samples were taken: (1) PM₁₀ collected simultaneously in indoor and outdoor air; (2) PM₁₀ and PM_2.5 collected simultaneously in indoor air. The aerosol particles were concentrated on quartz fibre filters with low-volume samplers equipped with size selective inlets. The filters were weighed and then extracted for cellulose analysis by an enzymatic method. The average indoor cellulose concentration was 1.01 ± 0.24 μg m^?3, whereas the average outdoor cellulose concentration was 0.078 ± 0.047 μg m^?3, accounting for 4.0% and 0.4%, respectively, of the PM₁₀ mass. The corresponding average ratio between indoor and outdoor cellulose concentrations was 11.1 ± 4.9, indicating that cellulose particles were generated indoors, most likely due to the handling of cotton-made textiles as a result of routine daily activities in the bedroom. Indoor cellulose concentrations averaged 1.22 ± 0.53 μg m^?3 in the aerosol coarse fraction (determined from the difference between PM₁₀ and PM_2.5 concentrations) and averaged 0.38 ± 0.13 μg m^?3 in the aerosol fine fraction. The average ratio between the coarse and fine fractions of cellulose concentrations in the indoor air was 3.6 ± 2.1. This ratio is in line with the primary origin of this biopolymer. Results from this study provide the first experimental evidence in support of a significant contribution of cellulose to the mass of suspended particles in indoor air.     

Ethanol emission from loose corn silage and exposed silage particles

Silage on dairy farms has been identified as a major source of volatile organic compound (VOC) emissions. However, rates of VOC emission from silage are not accurately known. In this work, we measured ethanol (a dominant silage VOC) emission from loose corn silage and exposed corn silage particles using wind tunnel systems. Flux of ethanol was highest immediately after exposing loose silage samples to moving air (as high as 220 g m^?2 h^?1) and declined by as much as 76-fold over 12 h as ethanol was depleted from samples. Emission rate and cumulative 12 h emission increased with temperature, silage permeability, exposed surface area, and air velocity over silage samples. These responses suggest that VOC emission from silage on farms is sensitive to climate and management practices. Ethanol emission rates from loose silage were generally higher than previous estimates of total VOC emission rates from silage and mixed feed. For 15 cm deep loose samples, mean cumulative emission was as high as 170 g m^?2 (80% of initial ethanol mass) after 12 h of exposure to an air velocity of 5 m s^?1. Emission rates measured with an emission isolation flux chamber were lower than rates measured in a wind tunnel and in an open setting. Results show that the US EPA emission isolation flux chamber method is not appropriate for estimating VOC emission rates from silage in the field.