Carbonaceous aerosol characteristics in outdoor and indoor environments of Nanchang, China, during summer 2009

A study of carbonaceous aerosol was initiated in Nanchang, a city in eastern China, for the first time. Daily and diurnal (daytime and nighttime) PM2.5 (particulate matter with aerodynamic diameter < or =2.5 microm) samples were collected at an outdoor site and in three different indoor environments (common office, special printing and copying office, and student dormitory) in a campus of Nanchang University during summer 2009 (5-20 June). Daily PM10 (particulate matter with aerodynamic diameter < or =10 microm) samples were collected only at the outdoor site, whereas PM2.5 samples were collected at both indoor and outdoor sites. Loaded PM2.5 and PM10 samples were analyzed for organic and elemental carbon (OC, EC) by thermal/optical reflectance following the Interagency Monitoring of Protected Visual Environments-Advanced (IMPROVE-A) protocol. Ambient mass concentrations of PM10 and PM2.5 in Nanchang were compared with the air quality standards in China and the United States, and revealed high air pollution levels in Nanchang. PM2.5 accounted for about 70% of PM10, but the ratio of OC and EC in PM2.5 to that in PM10 was higher than 80%, which indicated that OC and EC were mainly distributed in the fine particles. The variations of carbonaceous aerosol between daytime and nighttime indicated that OC was released and formed more rapidly in daytime than in nighttime. OC/EC ratios were used to quantify secondary organic carbon (SOC). The differences in SOC and SOC/OC between daytime and nighttime were useful in interpreting the secondary formation mechanism. The results of (1) OC and EC contributions to PM2.5 at indoor sites and the outdoor site; (2) indoor-outdoor correlation of OC and EC; (3) OC-EC correlation; and (4) relative contributions of indoor and outdoor sources to indoor carbonaceous aerosol indicated that OC indoor sources existed in indoor sites, with the highest OC emissions in I2 (the special printing and copying office), and that indoor EC originated from outdoor sources. The distributions of eight carbon fractions in emissions from the printer and copier showed obviously high OC1 (>20%) and OC2 (approximately 30%), and obviously low EC1-OP (a pyrolyzed carbon fraction) (<10%), when compared with other sources.     

Perfluoroalkyl acids in dust on residential indoor/outdoor window glass in Chinese cities: occurrence,composition, and toddler exposure

Environmental Science and Pollution Research - The dust on indoor and outdoor surfaces of the window glasses were collected using sterile cotton balls in 11 cities from China. Two sampling...     

Inorganic and carbonaceous components in indoor/outdoor particulate matter in two residential houses in Oslo, Norway

A detailed analysis of indoor/outdoor physicochemical aerosol properties has been performed. Aerosol measurements were taken at two dwellings, one in the city center and the other in the suburbs of the Oslo metropolitan area, during summer/fall and winter/spring periods of 2002-2003. In this paper, emphasis is placed on the chemical characteristics (water-soluble ions and carbonaceous components) of fine (PM2.5) and coarse (PM2.5-10) particles and their indoor/outdoor relationship. Results demonstrate that the carbonaceous species were dominant in all fractions of the PM10 particles (cut off size: 0.09-11.31 microm) during all measurement periods, except winter 2003, when increased concentrations of water-soluble inorganic ions were predominant because of sea salt transport. The concentration of organic carbon was higher in the fine and coarse PM10 fractions indoors, whereas elemental carbon was higher indoors only in the coarse fraction. In regards to the carbonaceous species, local traffic and secondary organic aerosol formation were, probably, the main sources outdoors, whereas indoors combustion activities such as preparation of food, burning of candles, and cigarette smoking were the main sources. In contrast, the concentrations of water-soluble inorganic ions were higher outdoors than indoors. The variability of water-soluble inorganic ion concentrations outdoors was related to changes in emissions from local anthropogenic sources, long-range transport of particles, sea salt emissions, and resuspension of roadside and soil dusts. In the indoor environment the infiltration of the outdoor air indoors was the major source of inorganic ions.     

DEARS particulate matter relationships for personal,indoor, outdoor,and central site settings for a general population

This analysis provides the initial summary of PM_2.5 mass concentrations relationships for all seasons and participants for a general population in the Detroit Exposure and Aerosol Research Study (DEARS). The summary presented highlights the utility of the new methodologies applied, in addition to summarizing the particulate matter (PM) data.Results include the requirement to adjust the exposure data for monitor wearing compliance and measured environmental tobacco smoke (ETS) levels, even though the study design specified a non-smoking household. A 40% wearing compliance acceptance level was suggested as necessary to balance minimizing exposure misclassification (from poor compliance) and having sufficient data to conduct robust statistical analyses. An ETS threshold level equivalent to adding more than 1.5 μg m^?3 to the collected sample was found to be necessary to detect changes in the personal exposure factor (F_pex). It is not completely clear why such a large threshold level was necessary.Statistically significant spatial PM_2.5 gradients were identified in three of the six DEARS neighborhoods in Wayne County. These were expected, given the number of strong, localized PM sources in the Detroit (Michigan) metro area. Some residential outdoor bias levels compared with the central site at Allen Park exceeded 15%. After adjusting for ETS biases, the outdoor contributions to the personal exposure were typically larger by factors from 1.75 to 2.2 compared with those of the non-outdoor sources. The outdoor contribution was larger in the summer than in the winter, which is consistent with the fractions of time spent outdoors in the summer vs. the winter (6.7% vs. 1.1% of the time).Mean personal PM_2.5 cloud levels for the general population DEARS cohort ranged from 1.5 to 3.8 (after ETS adjustment) and were comparable to those reported previously. The personal exposure collections indoors were typically at least 13 times greater than those contributed outdoors.     

Comparative study on indoor air quality in Japan and China: Characteristics of residential indoor and outdoor VOCs

We conducted a comparative study on the indoor air quality for Japan and China to investigate aromatic volatile organic compounds (VOCs) in indoor microenvironments (living room, bedroom, and kitchen) and outdoors in summer and winter during 2006–2007. Samples were taken from Shizuoka in Japan and Hangzhou in China, which are urban cities with similar latitudes. Throughout the samplings, the indoor and outdoor concentrations of many of the targeted VOCs (benzene, toluene, ethylbenzene, xylenes, and trimethylbenzenes) in China were significantly higher than those in Japan. The indoor concentrations of VOCs in Japan were somewhat consistent with those outdoors, whereas those in China tended to be higher than those outdoors. Here, we investigated the differences in VOC concentrations between Japan and China. Compositional analysis of indoor and outdoor VOCs showed bilateral differences; the contribution of benzene in China was remarkably higher than that in Japan. Significant correlations (p < 0.05) for benzene were observed among the concentrations in indoor microenvironments and between the outdoors and living rooms or kitchens in Japan. In China, however, significant correlations were observed only between living rooms and bedrooms. These findings suggest differences in strengths of indoor VOC emissions between Japan and China. The source characterizations were also investigated using principal component analysis/absolute principal component scores. It was found that outdoor sources including vehicle emission and industrial sources, and human activity could be significant sources of indoor VOC pollution in Japan and China respectively. In addition, the lifetime cancer risks estimated from unit risks and geometric mean indoor concentrations of carcinogenic VOCs were 2.3 × 10^?5 in Japan and 21 × 10^?5 in China, indicating that the exposure risks in China were approximately 10 times higher than those in Japan.     

Personal exposure to fine particulate matter in elderly subjects: relation between personal, indoor, and outdoor concentrations

The time-series correlation between ambient levels, indoor levels, and personal exposure to PM2.5 was assessed in panels of elderly subjects with cardiovascular disease in Amsterdam, the Netherlands, and Helsinki, Finland. Subjects were followed for 6 months with biweekly clinical visits. Each subject's indoor and personal exposure to PM2.5 was measured biweekly, during the 24-hr period preceding the clinical visits. Outdoor PM2.5 concentrations were measured at fixed sites. The absorption coefficients of all PM2.5 filters were measured as a marker for elemental carbon (EC). Regression analyses were conducted for each subject separately, and the distribution of the individual regression and correlation coefficients was investigated. Personal, indoor, and ambient concentrations were highly correlated within subjects over time. Median Pearson's R between personal and outdoor PM2.5 was 0.79 in Amsterdam and 0.76 in Helsinki. For absorption, these values were 0.93 and 0.81 for Amsterdam and Helsinki, respectively. The findings of this study provide further support for using fixed-site measurements as a measure of exposure to PM2.5 in epidemiological time-series studies.     

Heavy metals and Pb isotopic composition of aerosols in urban and suburban areas of Hong Kong and Guangzhou,South China—Evidence of the long-range transport of air contaminants

Rapid urbanization and industrialization in South China has placed great strain on the environment and on human health. In the present study, the total suspended particulate matter (TSP) in the urban and suburban areas of Hong Kong and Guangzhou, the two largest urban centres in South China, was sampled from December 2003 to January 2005. The samples were analysed for the concentrations of major elements (Al, Fe, Mg and Mn) and trace metals (Cd, Cr, Cu, Pb, V and Zn), and for Pb isotopic composition. Elevated concentrations of metals, especially Cd, Pb, V and Zn, were observed in the urban and suburban areas of Guangzhou, showing significant atmospheric trace element pollution. Distinct seasonal patterns were observed in the heavy metal concentrations of aerosols in Hong Kong, with higher metal concentrations during the winter monsoon period, and lower concentrations during summertime. The seasonal variations in the metal concentrations of the aerosols in Guangzhou were less distinct, suggesting the dominance of local sources of pollution around the city. The Pb isotopic composition in the aerosols of Hong Kong had higher ²⁰⁶Pb/²⁰⁷Pb and ²⁰⁸Pb/²⁰⁷Pb ratios in winter, showing the influence of Pb from the northern inland areas of China and the Pearl River Delta (PRD) region, and lower ²⁰⁶Pb/²⁰⁷Pb and ²⁰⁸Pb/²⁰⁷Pb ratios in summer, indicating the influence of Pb from the South Asian region and from marine sources. The back trajectory analysis showed that the enrichment of heavy metals in Hong Kong and Guangzhou was closely associated with the air mass from the north and northeast that originated from northern China, reflecting the long-range transport of heavy metal contaminants from the northern inland areas of China to the South China coast.     

Occurrence and distribution of polybrominated diphenyl ethers (PBDEs) in the dissolved and suspended phases of the sea-surface microlayer and seawater in Hong Kong, China

This study reports the first data on the concentration and distribution of polybrominated diphenyl ethers (PBDEs) in the sea-surface microlayer (SML), and their enrichment relative to bulk seawater, for coastal waters in the marine environment of Hong Kong, China. Samples were collected in March 2005 at five sample locations and analysed for eight congeners of primary interest, i.e. BDE 28, 47, 99, 100, 153, 156, 183 and 209. Concentration ranges of summation operatorPBDE in the dissolved phase (DP, defined as sum of truly dissolved and colloidal phase) and suspended particulate matter (SPM) of seawater were 31.1-118.7 pg/l (mean 70.7 pg/l), and 25.7-32.5 pg/l (mean 28.1 pg/l), respectively. Concentrations in the SML were generally higher by factor of 1.3-3.6 in the DP (concentration range from 40.2 to 228.2 pg/l, mean 149.2 pg/l) and by 0.3-2.1 in the SPM (concentration range 8.1-69.1 pg/l, mean 38.2 pg/l). Concentrations of PBDEs were general low and below detection limits in samples of an oceanic character and highest in the sheltered waters of Victoria Harbour. The congeners BDE 28, 47, 100 and 183 were most abundant, where BDE 209 was detected only in trace amounts. It is suggested that Hong Kong's marine waters show relatively low levels of PBDE contamination, and these compounds may originate from the disposal of electronic waste in southern China, as well as untreated discharge of wastewater locally.     

Monitoring personal,indoor, and outdoor exposures to metals in airborne particulate matter: Risk of contamination during sampling,handling and analysis

Rigorous sampling and quality assurance protocols are required for the reliable measurement of personal, indoor and outdoor exposures to metals in fine particulate matter (PM_2.5). Testing of five co-located replicate air samplers assisted in identifying and quantifying sources of contamination of filters in the laboratory and in the field. A field pilot study was conducted in Windsor, Ont., Canada to ascertain the actual range of metal content that may be obtained on filter samples using low-flow (4 L min⁻¹) 24-h monitoring of personal, indoor and outdoor air. Laboratory filter blanks and NIST certified reference materials were used to assess contamination, instrument performance, accuracy and precision of the metals determination. The results show that there is a high risk of introducing metal contamination during all stages of sampling, handling and analysis, and that sources and magnitude of contamination vary widely from element to element. Due to the very small particle masses collected on low-flow 24-h filter samples (median 0.107 mg for a sample volume of approximately 6 m³) the contribution of metals from contamination commonly exceeds the content of the airborne particles being sampled. Thus, the use of field blanks to ascertain the magnitude and variability of contamination is critical to determine whether or not a given element should be reported. The results of this study were incorporated into standard operating procedures for a large multiyear personal, indoor and outdoor air monitoring campaign in Windsor.     

A review of the impact of outdoor and indoor environmental factors on human health in China

Environmental Science and Pollution Research - The Intergovernmental Panel on Climate Change (IPCC) reported that global climate change has led to the increased occurrence of extreme weather...     

Evaluation of airborne particulate matter and metals data in personal,indoor and outdoor environments using ED-XRF and ICP-MS and co-located duplicate samples

Factors and sources affecting measurement uncertainty associated with monitoring metals in airborne particulate matter (PM) were investigated as part of the Windsor, Ontario Exposure Assessment Study (WOEAS). The assessment was made using co-located duplicate samples and a comparison of two analytical approaches: ED-XRF and ICP-MS. Sampling variability was estimated using relative percent difference (RPD) of co-located duplicate samples. The comparison of ICP-MS and ED-XRF results yields very good correlations (R² ≥ 0.7) for elements present at concentrations that pass both ICP-MS and ED-XRF detection limits (e.g. Fe, Mn, Zn, Pb and Cu). PM concentration ranges (median, sample number) of 24-h indoor PM₁₀ and personal PM₁₀ filters, and outdoor PM_2.5 filters were determined to be 2.2–40.7 (11.0, n = 48) μg m^?3, 8.0–48.3 (11.9, n = 48) μg m^?3, and 17.1–42.3 (21.6, n = 18) μg m^?3, respectively. The gravimetric analytical results reveal that the variations in PM mass measurements for same-day sampling are insignificant compared to temporal or spatial variations: 92%, 100% and 96% of indoor, outdoor and personal duplicate samples, respectively, pass the quality criteria (RPD ≤ 20%). Uncertainties associated with ED-XRF elemental measurements of S, Ca, Mn, Fe and Zn for 24-h filter samples are low: 78%–100% of the duplicate samples passed the quality criteria. In the case of 24-h filter samples using ICP-MS, more elements passed the quality criteria due to the lower detection limits. These were: Li, Na, K, Ca, Si, Al, V, Fe, Mn, Co, Cu, Mo, Ag, Zn, Pb, As, Mg, Sb, Sn, Sr, Th, Ti, Tl, and U. Low air concentrations of metals (near or below instrumental detection limits) and/or inadvertent introduction of metal contamination are the main causes for excluding elements based on the pass/fail criteria. Uncertainty associated with elemental measurements must be assessed on an element-by-element basis.     

Polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), dioxin-like polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in waterbird eggs of Hong Kong, China

Concentrations of PCDD/Fs, PCBs and PBDEs were measured in 56 egg samples collected from waterbirds of different species (Great Egret, Little Egret, Night Heron and Chinese Pond Heron) from different regions of Hong Kong (Ho Sheung Heung, Mai Po Village and Mai Po Lung Village) during 2000 and 2006. Dominance of 2,3,4,7,8-PeCDF indicates a signature associated with commercial usage of PCBs. Although no significant variations were observed within- and between-site in the levels of PCDD/Fs, coplanar PCBs and PBDEs, the concentrations of coplanar PCBs were much higher than PCDD/Fs. Similarity in composition profiles of PCDD/F and coplanar PCBs from different egretries is possibly associated with non-point sources of these contaminants to Hong Kong. Predominant accumulation of BDE-47, BDE-99 and BDE-100 suggested the penta-BDE technical mixtures usage in Hong Kong and its vicinity. Toxic equivalency and Monte Carlo simulation technique showed potential risks on waterbirds due to their exposure to PCDD/Fs.     

Levels and congener profiles of PCDD/Fs, PCBs and PBDEs in seafood from China

A nationwide investigation into polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs), polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs) in market seafood was conducted for the first time in this study. Total PCDD/F concentrations in fatty fish ranged from 0.13 to 8.64 pg g⁻¹ wet weight (mean 2.05 pg g⁻¹ wet weight), total PCB concentrations ranged from 38.9 to 3514 pg g⁻¹ wet weight (mean 1133 pg g⁻¹ wet weight), and total PBDE concentrations ranged from 42.8 to 913 pg g⁻¹ wet weight (mean 322 pg g⁻¹ wet weight). Corresponding mean toxicity equivalent (TEQ) values for total PCDD/F and dioxin-like PCB were 0.25 pg g⁻¹ wet weight (WHO 98-TEQ) and 0.32 pg g⁻¹ wet weight (WHO 98-TEQ), respectively. OCDD, PCB-138 and PBDE-47 were the dominant compounds according to their respective congeners. WHO 98-TEQ _{PCDD/PCDF/PCB} for fatty fish and shell fish were 0.60 and 0.070 pg g⁻¹ wet weight, respectively, lower than the standard set by the European Commission. The contamination levels and profiles were compared with those documented in previous publications.     

Modulation of steroidogenesis by coastal waters and sewage effluents of Hong Kong, China, using the H295R assay

BACKGROUND, AIM, AND SCOPE: The presence of a variety of pollutants in the aquatic environment that can potentially interfere with the production of sex steroid hormones in wildlife and humans has been of increasing concern. The aim of the present study was to investigate the effects of extracts from Hong Kong marine waters, and influents and effluents from wastewater treatment plants on steroidogenesis using the H295R cell bioassay. After exposing H295R cells to extracts of water, the expression of four steroidogenic genes and the production of three steroid hormones were measured. MATERIALS AND METHODS: Water samples were collected during the summer of 2005 from 24 coastal marine areas and from the influents and effluents of two major waste water treatment plants (WWTPs) in Hong Kong, China. Samples were extracted by solid phase extraction (SPE). H295R cells were exposed for 48 h to dilutions of these extracts. Modulations of the expression of the steroidogenic genes CYP19, CYP17, 3betaHSD2, and CYP11beta2 were determined by measuring mRNA concentrations by real-time polymerase chain reaction (Q-RT-PCR). Production of the hormones progesterone (P), estradiol (E2), and testosterone (T) was quantified using enzyme linked immunosorbent assays (ELISA). RESULTS: Extracts from samples collected in two fish culture areas inhibited growth and proliferation of H295R cells at concentrations greater or equal to 10(5) L equivalents. The cells were exposed to the equivalent concentration of active substances in 10,000 L of water. Thus, to observe the same level of effect as observed in vitro on aquatic organisms would require a bioaccumulation factor of this same magnitude. None of the other 22 marine samples affected growth of the cells at any dilution tested. Twelve of the marine water samples completely inhibited the expression of CYP19 without affecting E2 production; inhibition of CYP17 expression was observed only in one of the samples while expression of CYP11beta2 was induced as much as five- and ninefold after exposure of cells to extracts from two locations. The expression of the progesterone gene 3betaHSD2 was not affected by any of the samples; only one sample induced approximately fourfold the production of E2. Although more than twofold inductions were observed for P and T production, none of these values were statistically significant to conclude effects on the production of these two hormones. While influents from WWTPs did not affect gene expression, an approximately 30% inhibition in the production of E2 and a 40% increase in P occurred for the exposure with influents from the Sha Tin and Stonecutters WWTPs, respectively. Effluents from WWTPs did not affect the production of any of the studied hormones, but a decrement in the expression of the aldosterone gene CYP11beta2 was observed for the Sha Tin WWTP exposure. No direct correlation could be established between gene expression and hormone production. DISCUSSION: Observed cytotoxicity in the two samples from fish culture areas suggest the presence of toxic compounds; chemical analysis is required for their full identification. Although effluents from WWTPs did not affect hormone production, other types of endocrine activity such as receptor-mediated effects cannot be ruled out. Interactions due to the complexity of the samples and alternative steroidogenic pathways might explain the lack of correlation between gene expression and hormone production results. CONCLUSIONS: Changes observed in gene expression and hormone production suggest the presence in Hong Kong coastal waters of pollutants with endocrine disruption potential and others of significant toxic effects. The aromatase and aldosterone genes seem to be the most affected by the exposures, while E2 and P are the hormones with more significant changes observed. Results also suggest effectiveness in the removing of compounds with endocrine activity by the WWTPs studied, as effluent samples did not significantly affect hormone production. The H295R cell showed to be a valuable toll in the battery required for the analysis of endocrine disrupting activities of complex environmental samples. RECOMMENDATIONS AND PERSPECTIVES: Due to the intrinsic complexity of environmental samples, a combination of analytical tools is required to realistically assess environmental conditions, especially in aquatic systems. In the evaluation of endocrine disrupting activities, the H295R cell bioassay should be used in combination with other genomic, biological, chemical, and hydrological tests to establish viable modes for endocrine disruption and identify compounds responsible for the observed effects.     

The influence of mariculture on mercury distribution in sediments and fish around Hong Kong and adjacent mainland China waters

To study the influence of mariculture on mercury (Hg) speciation and distribution in sediments and cultured fish around Hong Kong and adjacent mainland China waters, sediment samples were collected from six mariculture sites and the corresponding reference sites, 200-300 m away from the mariculture sites. Mariculture activities increased total mercury, organic matter, carbon, nitrogen and sulfur concentrations in the surface sediments underneath mariculture sites, possibly due to the accumulation of unconsumed fish feed and fish excretion. However, methylmercury (MeHg) concentrations and the ratio of MeHg to THg (% MeHg) in sediments underneath mariculture sites were lower than the corresponding reference sites. The % MeHg in sediments was negatively correlated (r = −0.579, p < 0.05) with organic matter (OM) content among all sites, indicating that OM may have inhibited Hg methylation in surface sediments. Three mariculture fish species were collected from each mariculture site, including red snapper (Lutjanus campechanus), orange-spotted grouper (Epinephelus coioides) and snubnose pompano (Trachinotus blochii). The average MeHg concentration in fish muscle was 75 μg kg⁻¹ (wet weight), and the dietary intake of MeHg through fish consumption for Hong Kong residents was 0.37 μg kg⁻¹ week⁻¹, which was lower than the corresponding WHO limits (500 μg kg⁻¹ and 1.6 μg kg⁻¹ week⁻¹).     

Accumulation of metals,trace elements and semi-volatile organic compounds on exterior window surfaces in Baltimore

Organic films have been found to develop on window surfaces [Diamond et al., Environmental Science and Technology 34 (2000a) 2900]. The film contains organic compounds that are in dynamic equilibrium with the gas-phase in air, and organic and inorganic compounds and elements associated with deposited air particles. In this study, the exterior surfaces of windows were sampled in downtown and suburban Baltimore, Maryland. Higher concentrations of PCBs, PAH, metals and trace elements were found at downtown than a suburban site. PCBs in the films at downtown sites were dominated by penta and hexa homologue groups and PAH signatures resembled that of vehicle emissions. Twenty-six metals and trace elements were separated into two groups according to their enrichment factors (EF). Ag, Hg, Se, Sb and Zn had EF > 100, suggesting anthropogenic sources of these metals in the films; whereas Fe, Ca, Co, Cr and others had EF <10, suggesting a crustal origin. An unusual profile dominated by deca- and nona- PCBs and relatively higher concentrations of Ag, Hg and Zn may be attributable to emissions from a medical waste incinerator. Dry deposition fluxes of selected metals on windows were 1.4-94 times higher on windows with than without films, indicating that the film increases the dry deposition of particles and their associated chemicals. This implies that film development, which is associated with elevated VOC and SOC emissions to urban air, will increase film development that will, in turn, increase the accumulation of other atmospherically deposited constituents such as metals.     

Polybrominated, polychlorinated and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans and dioxin-like polychlorinated biphenyls in marine surface sediments from Hong Kong and Korea

In this study we investigated occurrences and distribution patterns of dioxin-related compounds (DRCs) such as polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs), polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) in marine surface sediments collected from the coastal waters of Hong Kong and Korea. In most sampling sites, concentrations of PCDDs were the highest, followed by DL-PCBs, PCDFs, PBDFs, PBDDs, MoBPCDDs and MoBPCDFs in this order. Levels of PBDD/Fs were generally 1-2 orders of magnitude lower than chlorinated analogues. Levels of PCDDs are higher than PCDFs in Hong Kong while levels of PBDFs are higher than PBDDs in Korea (p < 0.05). Report of PBDD/Fs and MoBPCDD/Fs in sediments from East Asian countries is novel and original. Environmental levels of PBDD/Fs are supposed to start increasing in accordance with rising production, use and disposal of brominated flame retardants (BFRs) and recycling processes of e-waste in Asian developing countries.     

Acid rain, storm period chemistry and their potential impact on stream communities in Hong Kong

Hong Kong experiences acid deposition, however, little is known about the potential impact upon aquatic ecosystems. In a small drainage basin observations reveal that despite acid rain runoff, both baseflow and stormflow, was close to neutral in terms of pH. During storm events chemical analysis reveals that calcium (Ca) concentrations tended to rise. It also appears that the input of acid rain may increase aluminium (Al) levels in the stream. Due to the increased levels of Ca and only slight changes in pH acid deposition may not be generating problems in this stream. The presence of mayflies reported elsewhere may further support the results of the chemical study.     

Characterization of particle number concentrations and PM<Subscript>2.5</Subscript> in a school: influence of outdoor air pollution on indoor air

Background, Aim and Scope  

The impact of air pollution on school children’s health is currently one of the key foci of international and national agencies. Of particular concern are ultrafine particles which are emitted in large quantities, contain large concentrations of toxins and are deposited deeply in the respiratory tract.     

The morphological structure of leaves and the dust-retaining capability of afforested plants in urban Guangzhou, South China

Purpose

Air pollution is a serious health problem throughout the world, exacerbating a wide range of respiratory and vascular illnesses in urban areas. The mass artificial plantation is very helpful to absorb dust and reduce pollution for conservation of the urban environment. The foliar surface of plants is an important receptor of atmospheric pollutants. Therefore, selection of suitable plant species for urban environment is very important.

Methods

The dust-retaining capability of urban trees in Guangzhou was determined at four different types of urban area, and the morphological traits of their leaves such as wax, cuticle, stomata, and trichomes were observed under a scanning electron microscope.

Results

It was determined that the dust-retaining capability of any given tree species is significantly different in the same place. Of the four studied tree species in the industrial area (IA) and commercial/traffic areas (CTA) type urban areas, the highest amounts of dust removed by Mangifera indica Linn was 12.723 and 1.482?g/m², respectively. However, in contrast, the equivalent maxima for Bauhinia blakeana is only 2.682?g/m² and 0.720?g/m², respectively. Different plant species have different leaf morphology. The leaf of M. indica has deep grooves and high stomata density which are in favor of dust-retained, and thus, their dust-retained capability is stronger, while B. blakeana has the cells and epicuticular wax with its stomata arranging regularly, resulting in poor dust catching capability. Leaf size was also shown to be related to dust capture for the four studied tree species.

Conclusions

The dust removal capacity of individual tree species should be taken into account in the management of greening plantation in and around an urban area. It was also shown that temporal variation in dust accumulation occurred over the 28-day observation period and this was discussed. Furthermore, spatial contrasts in dust accumulation were evidenced by the data. This reflected the differing pollution loadings of the four urban-type areas. The highest amount of dust accumulation was associated with the industrial area in which shipyard and steelworks occurred whilst the lowest dust accumulation was associated with the grounds of the University which was the control area.