Wind modeling of Chihuahuan Desert dust outbreaks

The Chihuahuan Desert region of North America is a significant source of mineral aerosols in the Western Hemisphere, and Chihuahuan Desert dust storms frequently impact the Paso del Norte (El Paso, USA/Ciudad Juarez, Mexico) metropolitan area. A statistical analysis of HYSPLIT back trajectory residence times evaluated airflow into El Paso on all days and on days with synoptic (non-convective) dust events in 2001–2005. The incremental probability—a measure of the areas most likely to have been traversed by air masses arriving at El Paso during dusty days—was only strongly positively associated with the region west–southwest of the city, a zone of known dust source areas. Focused case studies were made of major dust events on 15 April and 15 December 2003. Trajectories approached the surface and MM5 (NCAR/Penn State Mesoscale Model) wind speeds increased at locations consistent with dust sources observed in satellite imagery on those dates. Back trajectory and model analyses suggested that surface cyclones adjacent to the Chihuahuan Desert were associated with the extreme dust events, consistent with previous studies of dust storms in the Southern High Plains to the northeast. The recognition of these meteorological patterns serves as a forecast aid for prediction of dust events likely to impact the Paso del Norte.     

Investigations of an intense aerosol loading during 2007 cyclone SIDR – A study using satellite data and ground measurements over Indian region

Tropical cyclones are prominent weather systems characterized by high atmospheric pressure gradients and wind speeds. Intense tropical cyclones occur in India during the pre-monsoon (spring), early monsoon (early summer), or post-monsoon (fall) periods. Originating in both the Bay of Bengal (BoB) and the Arabian Sea (AS), these tropical cyclones often attain velocities of more than 100 km h^?1 and are notorious for causing intense rain and storm surge as they cross the Indian coast. In this study, we examine the changes in the aerosol properties associated with an intense tropical cyclone “SIDR”, that occurred during 11–16 November 2007 over BoB. This cyclone, accompanied with very strong surface winds reaching 223 km h^?1, caused extensive damage over Bangladesh. Ground-based measurements of Aerosol Optical Depth (AOD) in the neighboring urban environment of Hyderabad, India, showed significant variations due to changes in wind velocity and direction associated with the cyclone passage. The Terra-MODIS and AVHRR satellite images showed prevalence of dust particles mixed with emissions from anthropogenic sources and biomass-burning AS, while the aerosol loading over BoB was significantly lower. The positive values of Aerosol index (AI) obtained from the Ozone Monitoring Instrument (OMI) suggested the presence of an elevated aerosol layer over the West coast of India, AS and Thar Desert during and after the cyclone episode. Meteorological parameters from the MM5 mesoscale model were used to study the variations in winds associated with the cyclonic activity. Particulate matter loading over the region during the cyclone period increased by ～45% with an accompanying decrease in columnar aerosol optical depth. The variations in Angstrom parameters suggested coarse-mode particle loading due to dust aerosols as observed in satellite data.     

Sensitivity of surface characteristics on the simulation of wind-blown-dust source in North America

Recently, a wind-blown-dust-emission module has been built based on a state-of-the-art wind erosion theory and evaluated in a regional air-quality model to simulate a North American dust storm episode in April 2001 (see Park, S.H., Gong, S.L., Zhao, T.L., Vet, R.J., Bouchet, V.S., Gong, W., Makar, P.A., Moran, M.D., Stroud, C., Zhang, J. 2007. Simulation of entrainment and transport of dust particles within North America in April 2001 (“Red Dust episode”). J. Geophys. Res. 112, D20209, doi:10.1029/2007JD008443). A satisfactorily detailed assessment of that module, however, was not possible because of a lack of information on some module inputs, especially soil moisture content. In this paper, the wind-blown-dust emission was evaluated for two additional dust storms using improved soil moisture inputs. The surface characteristics of the wind-blown-dust source areas in southwestern North America were also investigated, focusing on their implications for wind-blown-dust emissions. The improved soil moisture inputs enabled the sensitivity of other important surface characteristics, the soil grain size distribution and the land-cover, to dust emission to be investigated with more confidence. Simulations of the two 2003 dust storm episodes suggested that wind-blown-dust emissions from the desert areas in southwestern North America are dominated by emissions from dry playas covered with accumulated alluvial deposits whose particle size is much smaller than usual desert sands. As well, the source areas in the northwestern Texas region were indicated to be not desert but rather agricultural lands that were “activated” as a wind-blown-dust sources after harvest. This finding calls for revisions to the current wind-blown-dust-emission module, in which “desert” is designated to be the only land-cover category that can emit wind-blown dust.     

Quantitative ED-EPMA combined with morphological information for the characterization of individual aerosol particles collected in Incheon,Korea

A quantitative single-particle analytical technique, called low-Z particle electron probe X-ray microanalysis, combined with the utilization of their morphological information on individual particles, was applied to characterize six aerosol samples collected in one Korean city, Incheon, during March 9–15, 2006. The collected supermicron aerosol particles were classified based on their chemical species and morphology on a single-particle basis. Many different particle types were identified and their emission source, transport, and reactivity in the air were elucidated. In the samples, particles in the “soil-derived particles” group were the most abundant, followed by “reacted sea-salts”, “reacted CaCO₃-containing particles”, “genuine sea-salts”, “reacted sea-salts + others”, “Fe-containing particles”, “anthropogenic organics”, (NH₄)₂SO₄, “K-containing particles”, and “fly ash”. The application of this single-particle analysis, fully utilizing their chemical compositional and morphological data of individual particles, clearly revealed the different characteristics of the six aerosol samples. For samples S3 and S5, which were sampled during two Asian dust storm events, almost all particles were of soil origin that had not experienced chemical modification and that did not entrain sea-salts during their long-range transport. For sample S1, collected at an episodic period of high PM₁₀ concentration and haze, anthropogenic, secondary, and soil-derived particles emitted from local sources were predominant. For samples S2, S4, and S6, which were collected on average spring days with respect to their PM₁₀ concentrations, marine originated particles were the most abundant. Sample S2 seems to have been strongly influenced by emissions from the Yellow Sea and Korean peninsula, sample S4 had the minimum anthropogenic influence among the four samples collected in the absence of any Asian dust storm event, and sample S6 seems to have entrained air pollutants that had been transported from mainland China over the Yellow Sea to Korea.     

The Collection and Analysis of Inorganic Dust Downwind of Source Effluents

Two directionally oriented high-volume samplers are used to pinpoint the collection of specific inorganic dusts from an industrial emission. One of the samplers is placed upwind of the source, and the other downwind. Both samplers are activated by winds blowing from the direction of the source to the downwind sampler. Both are de-activated when the wind shifts from the 30° sampling arc. Thus, the upwind sampler “sees” background dust, and the downwind sampler “sees” material originating from the source. Microsorban filters are used to collect the dust materials. The filter is then dissolved in benzene and the residue washed with benzene to remove the filter material and organic substances collected. The residue consists of dry, inorganic dust, which is then subjected to X-ray diffraction and optical microscopy, for analysis. This technique was successfully used to collect and analyze cement dust and mica dust from two separate industrial sources. The technique has promise for the analysis of a wide variety of inorganic materials which can be identified by X-ray diffraction, optical microscopy or other techniques.     

Contamination assessment of mercury and arsenic in roadway dust from Baoji,China

The physicochemical properties and the contamination levels of mercury and arsenic in roadway dust from Baoji, NW China were investigated using an Atomic Fluorescence Spectrophotometer. Contamination levels were assessed based on the geoaccumulation index and the enrichment factor. The results show that magnetic susceptibilities of roadway dust were higher than Holocene loess–soil of central Shaanxi Loess Plateau. The mean contents of organic matter, PM10 and PM100 were 8.8%, 21.8% and 98.6%, respectively. Mercury concentration ranged from 0.48 to 2.32 μg g^?1, with a mean value of 1.11 μg g^?1, 17.1 times the Chinese soil mercury background value and 37 times the Shaanxi soil mercury background value. Arsenic concentration ranged from 9.0 to 42.8 μg g^?1, with a mean value of 19.8 μg g^?1, 1.8 times the Chinese and Shaanxi soil arsenic background values. The geoaccumlation index and enrichment factor indicate that mercury in the dust mainly originated from anthropogenic sources with ratings of “strongly polluted” and “strongly to extremely polluted”, whereas arsenic in dust originated from both natural and anthropogenic sources, with a ratings of “moderately to strongly polluted” and “strongly polluted”. Industrial activities, such as a coal-fired power station, coke-oven plant, and cement manufacturing plant, augmented by vehicular traffic, are the anthropogenic sources of mercury and arsenic in the roadway dust.     

Source apportionment of particulate matter at urban mixed site in Indonesia using PMF

A receptor model of positive matrix factorization (PMF) was used to identify the emission sources of fine and coarse particulates in Bandung, a city located at about 150 km south-east of Jakarta. Total of 367 samples were collected at urban mixed site, Tegalega area, in Bandung City during wet and dry season in the period of 2001–2007. The samples of fine and coarse particulate matter were collected simultaneously using dichotomous samplers and mini-volume samplers. The Samples from dichotomous Samplers were analyzed for black carbon and elements while samples from mini-volume samplers were analyzed for ions. The species analyzed in this study were Na, Mg, Al, Si, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Pb, Cl^?, NO₃^?, SO₄^2?, and NH₄⁺. The data were then analyzed using PMF to determine the source factors. Different numbers of source factors were found during dry and wet season. During dry season, the main source factors for fine particles were secondary aerosol (NH₄)₂SO₄, electroplating industry, vehicle emission, and biomass burning, while for coarse particles, the dominant source factors were electroplating industry, followed by aged sea salt, volcanic dust, soil dust, and lime dust. During the wet season, the main source factors for fine particulate matter were vehicle emission and secondary aerosol. Other sources detected were biomass burning, lime dust, soil and volcanic dust. While for coarse particulate matter, the main source factors were sulphate-rich industry, followed by lime dust, soil dust, industrial emission and construction dust.     

Emission inventory of eight elements,Fe, Al,K, Mg,Mn, Na,Ca and Ti,in dust source region of East Asia

Based on calculation of the emission rate of the atmospheric mineral dust and the data of elemental contents in surface soils, this paper calculates the emission inventory of eight main elements of the atmospheric dust, Fe, Al, K, Mg, Mn, Na, Ca and Ti, in the dust source region of East Asia. As the dust sources in both Northern China and the Southern Mongolia are of three types and, in each of the six source type areas, surface soils are relatively uniform in soil types and soil texture, a simple method to calculate the emission of an element in one source type area is proposed by multiplying the total emission of the dust PM₁₀ and PM₅₀ in the source type area with the mean percentage content of the element in surface soils of the area. Comparison of our calculation of the total Fe emission in the source region of East Asia with the total Fe deposition to the North Pacific Ocean, measured and calculated by previous authors, shows very good agreement. This general method can also be used for the emission calculation of any other element.     

Enhancement of source traceability of atmospheric PM by elemental chemical fractionation

During a 1-year study (“Fine dust” Project) funded by the Lazio regional government (Italy), about 1000 daily PM₁₀ and PM_2.5 samples collected from six sites in the region were subjected to chemical fractionation based on differences in elemental solubility. In this way, it was possible to achieve meaningful characterization of the elemental composition of individual samples. For most of the investigated elements, we found significant differences between the extracted and the mineralized residual fraction. In general, fine particulate was best characterized by the composition of the extracted fraction, while coarse particles from traffic-related sources were best characterized using residues. For several metals (Cd, Pb, Sn, Sb and V) having a critical environmental impact, this result was particularly clear.The application of Principal Component Analysis (PCA) and receptor modelling (PCR) to the data set allowed us to evidence the enhancement of selectivity towards different emission sources that is obtained when chemical fractionated data are considered instead of total element content. Chemical fractionation seems to generate very selective markers for specific emission sources and in particular for re-suspended road dusts, one of the main factors responsible for the increase of elemental concentrations in urban areas.     

Estimation of source apportionment and potential source locations of PM2.5 at a west coastal IMPROVE site

Particle composition data for PM_2.5 samples collected at Kalmiopsis Interagency Monitoring of Protected Visual Environments (IMPROVE) site in southwestern Oregon from March 2000 to May 2004 were analyzed to provide source identification and apportionment. A total of 493 samples were collected and 32 species were analyzed by particle induced X-ray emission, proton elastic scattering analysis, photon-induced X-ray fluorescence, ion chromatography, and thermal optical reflectance methods. Positive matrix factorization (PMF) was used to estimate the source profiles and their mass contributions. The PMF modeling identified nine sources. In the Kalmiopsis site, the average mass was apportioned to wood/field burning (38.4%), secondary sulfate (26.9%), airborne soil including Asian dust (8.6 %), secondary nitrate (7.6%), fresh sea salt (5.8%), OP-rich sulfate (4.9%), aged sea salt (4.5 %), gasoline vehicle (1.9%), and diesel emission (1.4%). The potential source contribution function (PSCF) was then used to help identify likely locations of the regional sources of pollution. The PSCF map for wood/field burning indicates there is a major potential source area in the Siskiyou County and eastern Oregon. The potential source locations for secondary sulfate are found in western Washington, northwestern Oregon, and the near shore Pacific Ocean where there are extensive shipping lanes. It was not possible to extract a profile directly attributable to ship emissions, but indications of their influence are seen in the secondary sulfate and aged sea salt compositions.     

Sources of Fine Particulate Species in Ambient Air over Lake Champlain Basin,VT

Abstract

This study is a part of an ongoing investigation of the types and locations of emission sources that contribute fine particulate air contaminants to Underhill, VT. The air quality monitoring data used for this study are from the Interagency Monitoring of Protected Visual Environments network for the period of 2001–2003 for the Underhill site. The main source-receptor modeling techniques used are the positive matrix factorization (PMF) and potential source contribution function (PSCF). This new study is intended as a comparison to a previous study of the 1988–1995 Underhill data that successfully revealed a total of 11 types of emission sources with significant contributions to this rural site. This new study has identified a total of nine sources: nitrate-rich secondary aerosol, wood smoke, East Coast oil combustion, automobile emission, metal working, soil/dust, sulfur-rich aerosol type I, sulfur-rich aerosol type II, and sea salt/road salt. Furthermore, the mass contributions from the PMF identified sources that correspond with sampling days with either good or poor visibility were analyzed to seek possible correlations. It has been shown that sulfur-rich aerosol type I, nitrate aerosol, and automobile emission are the most important contributors to visibility degradation. Soil/dust and sea salt/road salt also have an added effect.     

PCDD/Fs and PCBs in ambient air in a highly industrialized city in Northern Italy

Ambient air samples were collected in five locations around a polychlorobiphenyl (PCB) production plant in a highly industrialized city in the north of Italy, for the analysis of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) and PCBs.PCDD/F atmospheric concentrations were lower than those generally detected in urban areas, while PCB concentrations were higher than in urban and industrialized areas in other countries, especially in the locations closest to the plant. To identify source emissions responsible for air pollution we used principal component analysis (PCA) to compare the “fingerprint” of the air in Brescia with some source-related experimental and published data. This analysis showed that the PCDD/F fingerprints were more similar to steel plant emission data, while none of the PCB air patterns were comparable to emission profiles, indicating that different sources are responsible for the concentration of these two pollutants. The highest PCB concentrations detected in the areas closest to the chemical plant are indicative of its impact on the surrounding environment.     

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available.In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM₁₀ and PM_2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM₁₀ in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650–1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called “pulling equations”.ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m^?3 (17%) in PM₁₀, 2.2 μg m^?3 (8%) of PM_2.5 and 0.3 μg m^?3 (2%) of PM₁. This reveals that resuspension was responsible of the 37%, 15% and 3% of total traffic emissions respectively in PM₁₀, PM_2.5 and PM₁. Therefore the overall traffic contribution resulted in 18 μg m^?3 (46%) in PM₁₀, 14 μg m^?3 (51%) in PM_2.5 and 8 μg m^?3 (48%) in PM₁. In PMF2 this mass explained by road dust resuspension was redistributed among the rest of sources, increasing mostly the mineral, secondary nitrate and aged sea salt contributions.     

Fine Particulate Matter Emissions Inventories: Comparisons of Emissions Estimates with Observations from Recent Field Programs

Abstract

Emissions inventories of fine particulate matter (PM_2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM_2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM_2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5–20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM_2.5 are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM_2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.     

Provenances of atmospheric dust over Korea from Sr–Nd isotopes and rare earth elements in early 2006

Sr and Nd isotopic composition of pre- and syn-Asian dust (Hwangsa) particles collected from three different water depths at two different offshore sites, western Korea and rare earth elemental composition of syn-Asian dust particles collected from three islands around the Korean Peninsula in late April 2006 were analyzed to interpret their provenance. The dust Sr–Nd isotopic compositions vary spatiotemporally, but they show specific values when the Hwangsa event occurred. Satellite images, airmass backward trajectory modeling, and comparison with Sr–Nd isotopic ratios and rare earth elements compositions of soils and desert sands of northern China all suggest the major source of dust particles for the late April 2006 Hwangsa event to be the Mu Us Desert in northern China. Dust particles of the pre-Hwangsa period include both background dusts and the previous Hwangsa event dust particles, and they are interpreted to have been originated from various arid regions of China such as the Hobq Desert, the Mu Us Desert, and the Taklamakan Desert in different times. Different background dust sources during pre-Hwangsa period in early 2006 resulted from the changing route of the westerlies.     

Hydrocarbon emissions from industrial release events in the Houston-Galveston area and their impact on ozone formation

Ambient measurements have shown that ozone formation in the Houston-Galveston area of Texas is frequently much more rapid than in other urban areas. One of the contributing factors is believed to be short-term episodic or “event” emissions from industrial facilities, particularly releases that contain significant mass fractions of highly reactive volatile organic compounds (HRVOCs). In this work, time series analyses are used to compare average annual flow rates for air pollutant emissions with those released during reported emission events. The results indicate that the magnitude and frequency of HRVOC event emissions are an important element in accurately reflecting ozone precursor emission patterns in the Houston-Galveston area, particularly in Harris, Brazoria, Galveston, and Chambers counties. More than 50% of the reported episodic (event) emissions of HRVOCs are ethene and approximately a third are propene; the remainders are isomers of butene and 1,3-butadiene. Most events last less than 24 h. The mass released in an event can vary from a few hundred to more than 100,000 lb, and the dominant type of industrial source is chemical manufacturers (SIC 2869). Daily emissions from a single facility can vary from annual average emissions by multiple orders of magnitude at a frequency of several times a year. Because there are so many facilities in the Houston-Galveston area, HRVOC emission variability of this magnitude can be expected daily, at some time and some location in the Houston-Galveston area. If the emission variability occurs at times and locations where atmospheric conditions are conducive to ozone formation, both ambient data and photochemical modeling indicate that industrial emission events can lead to elevated concentrations of ozone. Specifically, peak, area-wide ozone concentration can be increased by as much as 100 ppb for large HRVOC emission events.     

Fine particulate matter emissions inventories: comparisons of emissions estimates with observations from recent field programs

Emissions inventories of fine particulate matter (PM2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5-20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM2.s are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.     

Sources of fine particulate species in ambient air over lake Champlain Basin, VT

This study is a part of an ongoing investigation of the types and locations of emission sources that contribute fine particulate air contaminants to Underhill, VT. The air quality monitoring data used for this study are from the Interagency Monitoring of Protected Visual Environments network for the period of 2001-2003 for the Underhill site. The main source-receptor modeling techniques used are the positive matrix factorization (PMF) and potential source contribution function (PSCF). This new study is intended as a comparison to a previous study of the 1988-1995 Underhill data that successfully revealed a total of 11 types of emission sources with significant contributions to this rural site. This new study has identified a total of nine sources: nitrate-rich secondary aerosol, wood smoke, East Coast oil combustion, automobile emission, metal working, soil/dust, sulfur-rich aerosol type I, sulfur-rich aerosol type II, and sea salt/road salt. Furthermore, the mass contributions from the PMF identified sources that correspond with sampling days with either good or poor visibility were analyzed to seek possible correlations. It has been shown that sulfur-rich aerosol type I, nitrate aerosol, and automobile emission are the most important contributors to visibility degradation. Soil/dust and sea salt/road salt also have an added effect.     

Estimating PM10 air concentrations from dust storms in Iraq,Kuwait and Saudi Arabia

A model for the emission of PM₁₀ dust has been constructed using the concept of a threshold friction velocity which is dependent on surface roughness. Surface roughness in turn was correlated with geomorphology or soil properties for Kuwait, Iraq, part of Syria, Saudi Arabia, the United Arab Emirates and Oman. The PM₁₀ emission algorithm was incorporated into a Lagrangian transport and dispersion model. PM₁₀ air concentrations were computed from August 1990 through August 1991. The model predicted about the right number of dust events over Kuwait (events occur 18% of the time). The model results agreed quantitatively with measurements at four locations in Saudi Arabia and one in Kuwait for one major dust event (>1000 μg/m³). However, for smaller scale dust events (200–1000 μg/m³), especially at the coastal sampling locations, the model substantially over-predicted the air concentrations. Part of the over-prediction was attributed to the entrainment of dust-free air by the sea breeze, a flow feature not represented by the large-scale gridded meteorological data fields used in the model computation. Another part of the over-prediction was the model's strong sensitivity to threshold friction velocity and the surface soil texture coefficient (the soil emission factor), and the difficulty in accurately representing these parameters in the model. A comparison of the model predicted PM₁₀ spatial pattern with the TOMS satellite aerosol index (AI) yielded a spatial pattern covering a major portion of Saudi Arabia that was quite similar to the observed AI pattern.     

Transport of dusts from East Asian and non-East Asian sources to Hong Kong during dust storm related events 1996–2007

Over a twelve year period from 1996 to 2007, 76 dust storm related events (as days) in Hong Kong were selected for study, based on Aluminium and Calcium concentrations in PM₁₀. Four of the 76 events reach episodic levels with exceedances of the Hong Kong air quality standards. The purpose of the study is to identify and characterize dust sources impacting Hong Kong.Global distribution of aerosols in NASA’s daily aerosol index images from TOMS and OMI, are compared to plots generated by NRL(US)’s Navy Aerosol Analysis and Prediction System. Possible source areas are assigned by computing air parcel backward trajectories to Hong Kong using the NOAA HYSPLIT model. PM₁₀ and elemental data are analyzed for crustal mass concentrations and element mass ratios.Our analysis reveals that 73 out of the 76 dust events (96%) involve non-East Asian sources-the Thar, Central/West Asian, Arabian and Sahara deserts (Saharan influence is found in 63 events), which are previously not known to affect Hong Kong. The Gobi desert is the most frequent origin of dust, affecting 68 dust events while the Taklamakan desert impacts only 30 of the dust events. The impact of the Gobi desert in March and December is apparently associated with the northeast monsoon in East Asia.Our results also show a seasonal pattern in dust impact from both East Asian and more remote sources, with a maximum in March. Dust event occurrences are conspicuously absent from summer. Dust transport to Hong Kong is commonly associated with the passage of frontal low-pressure systems.The coarse size fraction of PM₁₀ concentrations were, as indicated by Al, Ca and Fe concentrations, about 4–8 times higher during dust events. The mean Ca/Al ratios of sources involving the Taklamakan desert are notably higher than those for non-East Asian sources owing to a higher Ca content of most of the East Asian deserts. The Fe/Al ratios follow a similar trend.Contributions from the desert sources are grossly estimated where possible, by using the average Al abundance of 8% in the upper continental crust to convert the Al mass in the PM₁₀ to dust concentrations. This is done for the six events identified with air mass purely of non-East Asian origin and the two events related only to the Thar/Arabian/Sahara deserts. Results reveal that the average contribution from the non-East Asian sources (including C/W Asia) is approximately 10% and, that from the Thar/Arabian/Sahara deserts is about 8%.