Review of concentrations and chemistry of trichloroacetate in the environment

This paper reviews the concentrations of trichloroacetate (TCA) in the atmosphere-plant-soil system. Data originate mainly from Europe. The median TCA concentration in rainwater and canopy drip decreased until 1995. From then the median TCA concentration in rainwater remains rather constant while for canopy drip later data are not available. The same seems to hold for concentrations in air although a very limited data set is available. The median concentrations in coniferous needles and groundwater are constant for the period observed. The median TCA concentrations in soil decreased until 1992 and then remained constant.The TCA formation from chlorinated solvents in the atmosphere may explain a substantial percentage of the TCA amount in the atmosphere. The TCA concentrations in rainwater and canopy drip indicate that there will be other sources contributing to 10-50%. Waste incineration, biomass burning and natural formation in the marine boundary layer are potential candidate sources of TCA, but nothing can be said as yet on their TCA emission rates. Anthropogenic emissions of chlorine could also be a source.TCA can be formed from chlorinated solvents by biota. However, for coniferous trees the uptake of TCA from soil may be the predominant route. Biotic and abiotic reactions can cause to formation of TCA in soil, but also formation of TCA from chlorinated solvents by biota that excrete TCA, may contribute. Mass balance calculations of the bioactive soil top layer show that the production rate of TCA in certain soil types could be substantial. The mass balance calculations could not distinguish between natural and anthropogenic sources in soil.     

Gamma irradiation of municipal sludge for safe disposal and agricultural use.

Gamma radiation was found to be an effective tool for hygienization of municipal wastewater sludge. The sludge received from the primary settling tank of a municipal wastewater treatment plant was gamma irradiated using a cobalt-60 source in a sludge hygienization research irradiator. The process parameters were adjusted to effectively eliminate coliform bacteria in the sludge and to prevent their regrowth. Irradiated sludge was found to be free of fecal coliform and could be directly disposed after drying in a landfill or used as manure. It could also be used as a medium for growth of Rhizobium sp for obtaining a bio-fertilizer.     

Assessment of the ecological potential of mine-water treatment wetlands using a baseline survey of macroinvertebrate communities

A baseline survey of macroinvertebrate populations in two mine-water treatment wetlands, one treating a net acidic spoil heap discharge and one a net alkaline ferruginous pumped mine water, was undertaken to assess the potential of these systems to provide habitats for faunal communities. Both wetlands were found to be impoverished in comparison to natural wetlands but did sustain a macroinvertebrate community that could support higher organisms. Wetland size and water quality in terms of pH, conductivity and metal concentrations were found to be important factors in determining the quality of the populations supported. Direct toxicity to organisms was unlikely to be the main cause of lower diversity, but the smothering of organisms via the precipitation of iron hydroxides particularly in the early parts of the treatment systems affected macroinvertebrate communities. The presence of areas of open water within the planted systems was found to be important for providing habitats for macroinvertebrates and this should be both a future design and maintenance consideration for environmental managers.     

A Laboratory Method for the Simulation of Automobile Exhaust and Studies of Catalyst Poisoning

The expected use of catalytic converters on automobiles to meet the legislated automotive emission standards makes desirable a laboratory method that permits realistic testing of these catalysts. Such a method should be versatile enough to simulate a wide range of conditions which are applicable for catalysts designed to oxidize hydrocarbons and carbon monoxide, or to reduce nitric oxide, as the case may be. For this purpose, we have modified a pulse-flame combustor, based on a design by Meguerian. The output of this simulator very closely resembles engine exhaust with respect to composition, space velocity, and contaminants. The durability of a monolithic or pelleted catalyst can be evaluated by long term exposure to the simulated exhaust and by periodic measurement of the catalyst activity as a function of temperature. The apparatus and the range of conditions that can be achieved are described in detail. Poisoning of a Pt catalyst by fuels containing low concentrations of lead was studied with this exhaust simulator and compared with results obtained in engine dynamometer tests; a satisfactory correlation of catalyst deterioration was established.     

垃圾焚烧厂焚烧底灰的处理研究

系统地研究了常州市环境卫生综合厂垃圾焚烧车间的底灰。研究结果表明，根据中国现行的污染控制标准，该厂的底灰属于一般废物，可以以建筑垃圾的方式处理。但对底灰的分选和分类研究结果表明，底灰含有一定量的未燃烬的有机废物，也有一些可回收利用的废物。因此，底灰应该先分选后，再对无利用价值的渣土作填埋或其他处置。     

苯酚的厌氧生物处理

采用不断增加苯酚浓度而降低葡萄糖浓度的方法可驯化厌氧污泥中的微生物,使厌氧污泥最终以苯酚为唯一碳源生长,可显著提高厌氧污泥降解苯酚的能力;对苯酚间歇厌氧降解过程进行了分析。苯酚浓度在0～1.680 mg/L范围内,其厌氧降解过程符合一级动力学。Aiba模型、Haldane模型和Teisser 模型均可很好地描述处于对数期时厌氧污泥的比生长速率与初始底物浓度之间的关系,其中以Teisser 模型模拟的效果最好。将驯化污泥接种于UASB中可实现对含酚废水处理的连续运行,最大的有机负荷达2 g COD/（L·d）,稳定运行时苯酚的去除率可维持在96%以上。     

生活垃圾可持续化填埋

通过对中国填埋场现状分析,提出了"可持续填理"的概念.认为生活垃圾填埋场将从单纯的最终处置场所演变为填埋与中转相结合的场所.填埋场的可持续发展也将从两方面得到体现:一为垃圾降解过程及其副产品处理中以能量形式得到利用,另一方面为稳定化后的垃圾及填埋场本身空间得到再一次的利用.     

Simulations of the dispersion of reactive pollutants in a street canyon,considering different chemical mechanisms and micromixing

The Stochastic Fields (SF) or Field Monte Carlo method has been used to model the dispersion of reactive scalars in a street canyon, using a simple chemistry and the CBM-IV mechanism. SF is a Probability Density Function (PDF) method which allows both means and variances of the scalars to be calculated as well as considering the effect of segregation on reaction rates. It was found that the variance of reactive scalars such as NO₂ was very high in the mixing region at roof-top level with rms values of the order of the mean values. The effect of segregation on major species such as O₃ was found to be very small using either mechanism, however, some radical species in CBM-IV showed a significant difference. These were found to be the seven species with the fastest chemical timescales. The calculated photostationary state defect was also found to be in error when segregation is neglected.     

Sensory Measurement of Ambient Traffic Odors

Laboratory determinations of ambient traffic odors were conducted in the streets of Stockholm. The measurements were made with a sensory method based on signal detection theory. The occurrence of odors was expressed by an index of detectability (d′) which was compared to the ambient carbon monoxide concentration and the rhythm of the traffic. The results showed that the detection technique employed could well be adjusted to field conditions by use of a mobile odor laboratory. Also, the odor index (d′) was correlated with other parameters in the trafficked environment in the expected way. The odorous emissions are likely to be diluted quickly as distance from the street increases. However, the relevance of the index of detectability as a measure of dose and response needs to be studied further.     

去除污泥中重金属铬的生物淋滤反应器设计与应用

用微生物方法去除污泥中重金属（生物淋滤法）是近年来发展的新技术，探索工程化的条件有重要的应用价值。设计了一套容积为1m^3的生物淋滤反应器，由生物淋滤池、搅拌器、曝气器和空气压缩机等构成。其中，搅拌叶轮由平叶桨和斜叶桨组合而成。利用制革污泥进行了半连续的生物淋滤试验，结果表明，在反应器中污泥与菌体和营养物质能充分混匀，经过2-5d的处理，污泥pH持续下降到2．0以下，污泥中铬的溶出率达90％-99．5％。     

去除污泥中重金属铬的生物淋滤反应器设计与应用

用微生物方法去除污泥中重金属(生物淋滤法)是近年来发展的新技术,探索工程化的条件有重要的应用价值。设计了一套容积为1 m3的生物淋滤反应器,由生物淋滤池、搅拌器、曝气器和空气压缩机等构成。其中,搅拌叶轮由平叶桨和斜叶桨组合而成。利用制革污泥进行了半连续的生物淋滤试验,结果表明,在反应器中污泥与菌体和营养物质能充分混匀,经过2~5 d的处理,污泥pH持续下降到2.0以下,污泥中铬的溶出率达90%~99.5%。     

Formation of chlorinated disinfection by-products in viticulture

Background, aim and scope  The use of sodium hypochlorite (HYP) in viticulture results in effluents which are contaminated with halogenated substances. These disinfection by-products (DBPs) can be quantified as group parameter ‘adsorbable organic halogens’ (AOX) and have not been determined in effluents of viticulture yet. The substances that are detected as AOX are unknown. The AOX can be composed of harmless substances, but even toxic contaminants. Thus, it is impossible to assess ecological impacts. The aim of this study is to determine the quantification of AOX and DBPs after the use of HYP. This will be helpful to reduce environmental pollution by AOX. Materials and methods  The potential of HYP to generate AOX was determined in laboratory-scale experiments. Different model solutions were treated with HYP according to disinfection processes in viticulture and conditions of AOX formation in effluents were simulated. AOX were quantified using the flask-shaking method and identified DBPs were investigated by gas chromatography–mass spectrometry. Results  Treatment with HYP resulted in the formation of AOX. The percentage conversion of HYP to AOX was up to 11%. Most important identified DBPs in viticulture are chloroform, dichloroacetic acid and trichloroacetaldehyde. In addition, the formation of carbon tetrachloride (CT), 1,1,1-trichloropropanone, 2,4-dichlorobenzoic acid and 2-chloro-/2,4-dichlorophenylacetic acid was investigated. It was demonstrated that reaction temperature, concentration of HYP and type of organic matter have important influence on the formation of chlorinated DBPs. Discussion  The percentage conversion of HYP to AOX was similar to other published studies. Although a correlation of single compounds and AOX is difficult, chloroform was the predominant AOX. Generation of the volatile chloroform should be avoided due to possible adverse effects. The generation of dichloroacetic acid is of minor importance on account of biodegradation. Trichloroacetaldehyde and 1,1,1-trichloropropanone are weak mutagens and their formation should be avoided. Conclusions  The generation of AOX and chlorinated DBPs can be minimised by reducing the concentrations of the organic materials in the effluents. The removal of organic matter before disinfection results in a decreased formation of AOX. HYP is an effective disinfectant; therefore, it should be used at low temperatures and concentrations to reduce the amount of AOX. If possible, disinfection should be accomplished by the use of no chlorine-containing agents. By this means, negative influences of HYP on the quality of wine can also be avoided. Recommendations and perspectives  Our results indicate that HYP has a high potential to form AOX in effluents of viticulture. The predominant by-products are chloroform, dichloroacetic acid and trichloroacetaldehyde. In further research, wastewaters from a winery and the in- and outflows of two sewage treatment plants were sampled during vintage and analysed. These results will be discussed in a following paper.     

Electrostatic Precipitator Performance from the Point of View of Gas Treatment Time

This paper describes a risk assessment methodology for preliminary assessment of municipal sludge incineration. The methodology is a valuable tool in that it can be used for determining the hazard indices of chemical contaminants that might be present in sewage sludge used in incineration. The paper examines source characteristics (i.e., facility design), atmospheric dispersion of emission, and resulting human exposure and risk from sludge incinerators. Seven of the ten organics were screened for furtherinvestigation. An example of the calculations are presented for cadmium.     

A column method for determination of leaching of polycyclic aromatic hydrocarbons from aged contaminated soil

In this study a column leaching method for investigation of hydrophobic organic contaminants (HOCs) leaching from soil was developed. The method set-up is based on a recycled flow of sterile water through a soil column with a sedimentation chamber mounted on top of the column, in connection with on-line filtration. The combination of a sedimentation chamber and an on-line filtration enables the measurement of leaching concentrations from contaminated materials consisting of very fine particle fractions. In addition, by using on-line solid phase extraction, minute amounts of leaching HOCs may be captured and quantified with high accuracy and reproducibility. The method was applied successfully on a contaminated aged soil sample and the leaching behavior of seven PAHs, with three to six aromatic rings, was monitored for more than 1600 h under saturated conditions. The tested PAHs were fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benzo(a)pyrene and benzo(ghi)perylene. The method proved to be reliable and capable of providing data on leachable amounts of the PAHs under field-like conditions and over a longer period of time. The results indicated low availability of the studied contaminants since only a minor fraction (0.3%) of the initial amount of PAHs in the soil was removed during the experiment (liquid/solid-ratio of 700 l/kg). Thus PAHs in aged contaminated soil are not to be expected to be released to any great extent only by leaching with water.     

移动通信GSM网络与3G网络共站址下的环境影响评价

阐述了移动通信GSM网络与3G网络共站址的情况下对环境的影响，并提出了影响预测模式，计算了某通信公司移动通信典型基站对周围环境电磁辐射的影响，确定了对敏感目标的保护距离，并进行了实测以对保护距离进行验证。     

Evaluation of a sustainable remediation option: Beneficial reuse of petroleum-contaminated sediment as an energy source

The characteristics of petroleum-contaminated sediment (PCS) have been evaluated to assess whether the practice of its beneficial reuse as a sole or supplemental energy source is sustainable relative to other sediment remediation options such as monitored natural recovery (MNR), capping, or off-site disposal. Some of these remediation options for PCS are energy-intensive and/or require land utilization. The energy and compositional analysis results indicate a low carbon content (15–17%(wt)) and corresponding low energy values of 5,200 kJ/kg (2,200 Btu/lb) to 5,600 kJ/kg (2,400 Btu/lb). However, given other decision-making criteria, the sediment may contain enough value to be added as a supplemental fuel given that it is normally considered a waste product and is readily available.

The thermogravimetric profiles obtained under both combustion and pyrolytic conditions showed that the sulfur contents were comparable to typical low sulfur bituminous or lignite coals found in the United States, and most of the volatiles could be vaporized below 750°C. The heavy metal concentrations determined before and after combustion of the PCS indicated that further engineering controls may be required for mercury, arsenic, and lead. Due to the potential for reduction of public health and environmental threats, potential economic savings, and conservation of natural resources (petroleum and land), removal of PCS by dredging and beneficial reuse as a supplemental fuel clearly has merit to be considered as a sustainable remediation option.

Implications: This study will provide a logical evaluation process to determine whether petroleum-contaminated sediment can be reused as an energy source. The energy and emissions values were determined and evaluated whether the sediment could be combusted for viable and sustainable use, considering several factors pertinent to evaluate in the remediation decision process. Various analysis methods were employed to determine elemental compositions, heating values, thermal and emission characteristics. This evaluation process may be used as a general methodology for the determination of petroleum-contaminated sediment as a supplemental fuel that may have merit to be considered as a sustainable remediation option.     

Use of residence time distribution for evaluation of gaseous pollutant volatilization from stored swine manure

Abstract

A quantification analysis for evaluation of gaseous pollutant volatilization as a result of mass transfer from stored swine manure is presented from the viewpoint of residence time distribution. The method is based on evaluating the moments of concentration vs. time curves of both air and gaseous pollutants. The concept of moments of concentration histories is applicable to characterize the dispersal of the supplied air or gaseous pollutant in a ventilated system. The mean age or residence time of airflow can be calculated from an inverse system state matrix [B]‐1 of a linear dynamic equation describing the dynamics of gaseous pollutant in a ventilated airspace. The sum elements in an arbitrary row i in matrix [B]‐1 is equal to the mean age of airflow in airspace i. The mean age of gaseous pollutant in airspace i can be obtained from the area under the concentration profile divided by the equilibrium concentration reading in that space caused by gaseous pollutant sources. Matrix [B]‐1 can also be represented in terms of the inverse local airflow rate matrix ([W]‐1), transition probability matrix ([P]), and air volume matrix ([V]) as, [B]‐1 =[W]‐1[P][V]. Finally the mean age of airflow in a ventilated airspace can be interpreted by the physical characteristics of matrices [W] and [P]. The practical use of the concepts is also applied in a typical pig unit.     

Determination of aromatic hydrocarbons in submicrogram quantities in aqueous systems by means of high performance liquid chromatography

One liter of the water sample is extracted with 1,1,2-trichlorotrifluoroethane. This non-polar solvent with a low boiling point is then concentrated and a portion of the concentrated extract is injected in a high performance liquid chromatography system. Polar material is separated from the hydrocarbons by means of a silica gel column. The detector measures the UV absorbance at 254 nm at which wavelength aromatic compounds absorb especially well. The quantitative values are given as phenanthrene equivalents and amounts as small as 20 ng/l can be detected. The standard deviation of the method is ± 50 ng/l. Both these values can be improved with a limited amount of difficulty. A concentrated sample extract can be injected and evaluated in less than 6 minutes, and the method is simple enough to have been used at sea.     

Estimation of measurement uncertainty associated to the determination of pesticide residues: a case study

In the analytical analysis the measurement uncertainty is a quantitative indicator of the confidence describing the range around a reported or experimental result within which the true value can be expected. Several approaches can be used to estimate the measurement uncertainty associated to the analysis of pesticide residues: a) the top-down, the estimation can be referred to default values; b) the bottom-up the estimation is related to the uncertainty sources. Concerning the bottom-up approach, the following contributions have been investigated: weight of sample, calibration solutions, final volume of sample and intermediate repeatability studies. The commodity/residue combination selected in this study was celery/tau-fluvalinate pesticide. Tau-fluvalinate is a broad-spectrum insecticide in the pyrethroid class of pesticides. The Maximum Residue Limit (MRL) of tau-fluvalinate in celery has been set at 0.01 mg/kg. The tau- Fluvalinate showed two chromatographic peaks. Since the individual standards are not available, the two peaks were integrated separately and the instrumental responses were added. The total residue was calculated on the basis of resulted peaks. The present work aims to compare the uncertainty estimated by experimental data using repeated analysis (n = 12) of a real sample and a spiked sample. The relative expanded uncertainty for two data set, incurred and spiked, was 22 % and 20 %, respectively. No differences were observed from repeated determinations of real samples and spiked samples.     

Stochastic evaluation of mass discharge from pointlike concentration measurements

The contaminant mass discharge crossing a control plane is an important metric in the assessment of natural attenuation at contaminated sites. For risk-assessment purposes, the mass discharge must be estimated together with a level of uncertainty. We present a conditional Monte Carlo approach that allows estimating the statistical distribution of mass discharge. The approach is based on conditioning multiple realizations of the hydraulic conductivity field on all data available. We jointly determine a first-order decay coefficient in each realization, leading to conditional statistical distributions of all estimated parameters and the total mass discharge. The resulting statistical distribution of contaminant mass discharges can be used in the assessment of risks at the contaminated site. The method is applied to data of hypothetical test cases, which gives the opportunity to compare estimation results to the true field. As concentration data, we account for pointlike measurements obtained in multi-level sampling wells. The obtained empirical distribution of mass discharge crossing the multi-level sampling fence could be well fitted by a log-normal distribution.