氧化法去除燃煤烟气中Hg~0技术的研究进展

燃煤烟气中汞的排放控制是大气污染治理的研究热点之一。氧化法可将烟气中不溶于水的气态单质汞(Hg~0)转化为易溶于水的氧化态汞(Hg~(2+)),然后利用湿式吸收设备去除。综述了国内外燃煤烟气氧化法脱汞技术的研究进展,比较了非催化氧化法和催化氧化法的优势与局限,对今后的发展趋势进行了展望。指出:选择使用高效且环境友好的氧化剂以及催化剂,研发高效、低成本、可回收的金属氧化物催化剂是该领域的主要研究方向。     

Polycyclic aromatic hydrocarbon (PAH) emission from co-firing municipal solid waste (MSW) and coal in a fluidized bed incinerator

Polycyclic aromatic hydrocarbons (PAH) emissions from a commercial municipal solid waste incinerator (MSWI) were studied. A MSW–coal mixture and coal only were used as fuel for the fluidized bed incinerator. Seven sampling points were chosen according to the classified four PAH emission pathways: flue gas, residue, ash and water. The mixture of MSW and coal resulted in PAH emission more than that of coal only, and PAH emission increased with increasing MSW mass percentage. Calcium oxide (CaO) or calcium carbonate (CaCO₃) was added as a desulfurizer. PAH emission also changed with different desulfurizers because of their different influences on heat balance. The PAH toxic equivalent (TEQ) of all operating conditions was also examined, showing that total daily PAH emission from MSWI can be determined.     

Experimental study on flue gas purifying of MSW incineration using in-pipe jet adsorption techniques

This paper presents the experimental research process and results about flue gas purifying of municipal solid wastes (MSW) incineration using in-pipe jet adsorption techniques. MSW incineration was carried out in a fluidized bed test rig, and the flue gas purifying was carried out in an in-pipe jet adsorption test rig. The experimental results are as follows: when the feedstock of activated carbon is 1.6g/Nm(3), the desulfurization efficiency is 83%, the denitrification efficiency is 41%, and the dechlorination efficiency is 27%. The order of purifying effect of the three kinds of adsorbents on acidic gases from MSW incineration is activated carbon>activated bauxite>kaolin. Comparison of adsorption capabilities of the three kinds of adsorbents to heavy metals shows that activated carbon is the best additive to remove Cd, Pb and Cu, kaolin is inferior, and activated bauxite is the worst one. However, activated bauxite is the best additive to remove Hg, and it can remove Cd effectively. PAHs in fly ash are dominated by three-, four-, and five-ringed PAHs, and PAHs in the flue gas mainly include three- and four-ringed PAHs. When the injected quantity of additive is constant, the order of cleaning effect on PAHs is kaolin>activated carbon>activated bauxite. These three kinds of adsorbents have different purifying effects on acidic gases, heavy metals and PAHs in the flue gas from MSW incineration. In general, activated carbon has a better adsorption capability.     

烟气脱硝技术的研究

氮氧化物(NOx)的污染危害是一个不容忽视的问题.目前,我国燃煤电厂排放烟气的SO2治理已逐步走向正轨,新建的燃煤电厂基本都安装效率较高的脱硫装置.因此,控制NOx的排放将是下一步的主要任务.对选择性催化还原法(SCR)、非选择性催化还原法(SNCR)、电子束或电晕放电脱硝法、光催化氧化法等烟气中NOx控制技术的机理、现状、发展趋势和主要优缺点进行了详尽的论述.通过对各种工艺技术的脱除效率、应用条件、经济性等方面的分析、比较和总结,提出了未来脱硝技术研究工作的重点.基于我国的实际情况提出了烟气脱硝的可行方案,从而为工业废气脱硝技术的进一步开发和研究提供参考.     

On-line detection of metal pollutant spikes in MSW incinerator flue gases prior to clean-up

SUWIC's unique mobile metals emissions monitoring laboratory has been used to measure metal pollutant spikes in the flue gas from a municipal solid waste incinerator, prior to gas clean-up. The laboratory has a heated sampling probe that extends into the plant, allowing the simultaneous on-line measurement of the concentrations of more than 30 metals by Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES). As little is known about temporal variation in metal concentrations, this capability is seen as a major advance. The graphs of continuous measurements show that the elemental loading is far from uniform, and that concentrations fluctuate far more than may have been conventionally expected. There are occasional significant spikes in the emission profiles for cadmium and mercury, which are believed to be due to specific items in the waste feed material. Continuous monitoring measurements are of significant value for those seeking to model metal behaviour in combustion and in pollution control devices.     

垃圾焚烧烟气中二(噁)英零排放技术实践

介绍了绍兴新民热电有限公司用煤和垃圾混烧循环流化床技术处理城市生活垃圾，焚烧烟气经活性炭吸附、半干法和布袋除尘器净化工艺处理后，烟气中二噁英接近零排放。     

燃煤电厂烟气中汞的排放与控制研究进展

对煤中微量元素的丰度和赋存状态进行了论述，综述了燃煤烟气中重金属汞的排放、形态转化及分布情况，并重点论述了燃煤烟气中汞的监测和控制方法的最新进展，分析了燃煤电厂在汞控制方面存在的主要问题，并结合我国国情提出了相关建议。     

烟气中NOx脱除技术的研究进展

综述了干法脱硝、湿法脱硝、微生物法和化学吸收-生物还原法脱除烟气中氮氧化物的原理、技术特点和存在的问题。指出：化学吸收-生物还原法是未来脱除烟气中氮氧化物的主要研究方向之一,可通过提高NO在水中的溶解性,利用微生物去除氮氧化物,力争将其从实验室研究推广至工业应用。     

垃圾焚烧炉烟气净化系统的工艺分析

介绍了两种垃圾焚烧电厂烟气净化处理工艺,分析了垃圾焚烧烟气净化处理装置工艺流程及出口排放参数,提出目前适合的处理工艺及发展方向。     

Mineralogy and pore water chemistry of a boiler ash from a MSW fluidized-bed incinerator

This paper presents an investigation of the mineralogy and pore water chemistry of a boiler ash sampled from a municipal solid waste fluidized-bed incinerator, subject to 18 months of dynamic leaching in a large percolation column experiment. A particular focus is on the redox behaviour of Cr(VI) in relation to metal aluminium Al⁰, as chromium may represent an environmental or health hazard. The leaching behaviour and interaction between Cr(VI) and Al⁰ are interpreted on the basis of mineralogical evolutions observed over the 18-month period and of saturation indices calculated with the geochemical code PhreeqC and reviewed thermodynamic data. Results of mineralogical analyses show in particular the alteration of mineral phases during leaching (e.g. quartz and metal aluminium grains), while geochemical calculations suggest equilibria of percolating fluids with respect to specific mineral phases (e.g. monohydrocalcite and aluminium hydroxide). The combination of leaching data on a large scale and mineralogical analyses document the coupled leaching behaviour of aluminium and chromium, with chromium appearing in the pore fluids in its hexavalent and mobile state once metal aluminium is no longer available for chromium reduction.     

燃煤烟气中CO_2脱除方法的分析与探讨

作为主要的温室气体,CO2减排问题引起全球范围的广泛关注。阐述了燃煤烟气中CO2脱除的多种方法,分析比较了CO2的吸收法、吸附法、膜分离法等的特点及各自的优缺点,侧重介绍了有机胺和氨水脱除的技术进展,并介绍了氨水烟气脱碳的部分试验结果。     

CFD simulation of MSW combustion and SNCR in a commercial incinerator

A CFD scheme was presented for modeling municipal solid waste (MSW) combustion in a moving-grate incinerator, including the in-bed burning of solid wastes, the out-of-bed burnout of gaseous volatiles, and the selective non-catalytic reduction (SNCR) process between urea (CO(NH₂)₂) and NO_x. The in-bed calculations provided 2-D profiles of the gas–solid temperatures and the gas species concentrations along the bed length, which were then used as inlet conditions for the out-of-bed computations. The over-bed simulations provided the profiles of incident radiation heat flux on the top of bed. A 3-dimensional benchmark simulation was conducted with a 750 t/day commercial incinerator using the present coupling scheme incorporating with a reduced SNCR reduction mechanism. Numerical tests were performed to investigate the effects of operating parameters such as injection position, injection speed and the normalized stoichiometric ratio (NSR) on the SNCR performance. The simulation results showed that the distributions of gas velocity, temperature and NO_x concentration were highly non-uniform, which made the injection position one of the most sensitive operating parameters influencing the SNCR performance of moving grate incinerators. The simulation results also showed that multi-layer injections were needed to meet the EU2000 standard, and a NSR 1.5 was suggested as a compromise of a satisfactory NO_x reduction and reasonable NH₃ slip rates. This work provided useful guides to the design and operation of SNCR process in moving-grate incinerators.     

烟气连续排放监测系统的应用

简要介绍了绍丹东电厂现有烟气连续排放监测系统（CEMS）的构成,各分析仪的工作原理及现场使用情况,为CEMS的选型提供一定的参考。     

燃煤烟气中多环芳烃的富集技术

介绍了燃煤电厂烟气中排放的多环芳烃污染物的富集方法,比较了各种富集技术的特点与使用情况,分析了多环芳烃富集过程中的质量控制与质量保证措施,并探讨了富集采样中的若干注意事项.     

Surrogate study for dioxins from municipal waste incinerator in startup condition: applicability as a dioxin control indicator and an organohalogen emission warning

Dioxins and their surrogates were continuously monitored during the startup of two municipal waste in cinerators (MWIs). The surrogates studied included low-volatility organohalogen compounds (LVOH) sampled by online systems, as well as chlorobenzenes (CBs) and chlorophenols (CPs). The changes in levels of LVOH, CBs, and CPs corresponded well with the trend of the toxicity equivalent quantity (TEQ). The correlation of LVOH with TEQ was fairly good, whereas that of CBs and CPs with TEQ was not consistent. The correlation of LVOH with TEQ involved a memory effect related to the delayed emission of less volatile compounds. The isomer analysis of the dioxins present under startup conditions showed evidence of the memory effect, i.e., highly chlorinated isomers were emitted slowly, whereas low-chlorinated isomers and LVOH decreased rapidly as the temperature rose. LVOH cannot act as a perfect dioxin surrogate, but it can give a versatile, quick, and comprehensive warning of the presence of organohalogen compounds because it is free from the memory effect and covers many kinds of organohalogen compounds, including dioxins.     

活性焦烟气脱汞的试验研究与数值模拟

采用固定床吸附系统,对自制褐煤活性焦的脱汞性能进行了试验研究,研究发现自制活性焦对烟气中Hg0有一定的吸附能力,随着Hg0的入口浓度的增加,活性焦质量的增加,活性焦的吸附量也在增加。40mg时3号活性焦由10ng/min汞入1：2浓度时26．68％的最大吸附效率提高到40ng／min汞入口浓度时的53．12％。10ng/min汞入口浓度时3号活性焦在40mg时的最大吸附效率为26．68％,而在80mg时吸附效率提高到43．2％。烟气中的SO2、NO气体对活性焦吸附汞有一定的促进作用。在试验的基础上建立了固定床吸附系统的数学模型,基于Lan—mguir吸附系数,考虑吸附过程中颗粒内、外的传质控制过程,建立质量平衡方程。通过Matlab模型计算,计算结果与试验结果基本吻合,计算的活性焦脱汞效率要优于试验数值,计算的是理想情况下活性焦对汞的吸附效率,实际情况会有所降低。     

ClO_2溶液去除烟气中NO的效果及工程应用

采用实验室规模喷淋脱硝装置对ClO_2溶液去除NO的效果及影响因素进行探讨,通过脱硝产物的测定对ClO_2溶液去除NO的能力及机理进行分析;在此基础上考察ClO_2溶液对供热厂燃煤锅炉烟气的实际脱硝效果。实验结果表明:在液气比为20L/m~3、反应温度为20℃,反应pH为4.0、进气NO质量浓度为250 mg/m~3,ClO_2质量浓度为200 mg/L的条件下,NO去除率达97%以上;ClO_2溶液可将NO氧化吸收为NO_3~-,氧化后产生的NO_x也可被NaOH溶液吸收转化为NO_2~-和NO_3~-;在ClO_2质量浓度为200~500 mg/L,反应pH为5.5~7.0的条件下处理初始NO质量浓度为212~230 mg/m~3的燃煤锅炉烟气,NO去除率为85.7%~94.6%,NO_x去除率为80.4%~88.8%,出口NO_x质量浓度低于46 mg/m~3,远低于GB 13271—2014规定的排放限值。     

密相烟气颗粒团聚及破碎方法的研究

针对半干法烟气脱硫过程中脱硫刺利用率低的问题，从密相烟气颗粒团聚及破碎机理出发，提出了一套能够有效打碎颗粒团、强化烟气和脱硫剂接触的破碎机构。利用CFX软件模拟了破碎机构的形状、尺寸及排列方式等对气固接触的影响。模拟给出了脱硫塔内流场的变化，模拟的各种结构中三角形机构能够有效地打破颗粒团。     

Emission of dioxins/furans and other U-POPs from test burns of non-POP pesticides in a hazardous waste incinerator

This paper presents the results of test burns for obsolete pesticides (OPs) of the permethrin group in a high temperature incinerator (HTI) in Southeast Asia. Three test burn runs were conducted, a baseline run when no OP was fed to the incinerator, and two test runs with different mixtures of OP compounds (formula 1 and 2, refer to Table 1 for detail) containing chlorine in the feeding wastes. The unintentional formed persistent organic pollutants (U-POPs) including 17 dioxins/furans, 12 dioxin-like PCBs and 12 chlorobenzenes (CBs) were monitored in all input materials and all discharges (flue gas, scrubbing liquid and solid residues). The results show relatively high levels of the U-POPs in the flue gas emission with total dioxins/furans of 4.4, 3.4, and 8.4 ng I-TEQ/m³ in the baseline, test run 1 and test run 2, respectively, which are above international acceptable emission levels. The PCB levels in flue gas were, respectively, 0.01, 0.3 and 0.4 ng I-TEQ/m³. The baseline thus had similar U-POPs levels with the OP test runs.In stack emission, approximately 90% of the U-POPs and 100% of CBs were present in gas phase. The emission factors, mass of pollutants per metric ton (tonne) of input waste, of U-POPs associated with fly ash (from bag house) were the highest, followed by flue gas and bottom ash while those associated with scrubbing liquid were relatively low. Among the waste input material only the black toner power contained U-POPs, but at low levels. The profiles of the dioxins/furans and PCBs in the toner waste were significantly different from that in the discharges. Despite the overall good destruction and removal efficiency of permethrin (better than 90%) the high emission of U-POPs and CBs from the test burn is of another more serious concern. To our best knowledge the findings of this study are the first of this kind for the Southeast Asia. The findings emphasize that if not properly conducted a standard destruction technology of a non-POP chemical can lead to a release of a range of more dangerous U-POPs into the environment.