Tire debris organic extract affects Xenopus development

Tire debris (TD) and its organic components were identified as a main source of PM10 atmospheric and water pollution. Because few data are available on the embryotoxic effects of TD organic components, the lethal and teratogenic potential of tire debris organic extract (TDOE) was evaluated using the frog embryo teratogenesis assay-Xenopus (FETAX), coupled with a histopathological screening of the survived larvae. From stage 8 to stage 47, Xenopus laevis embryos were exposed to TDOE at concentrations of 50, 80, 100, 120 and 140 mg/L. The results showed 50 mg/L TDOE to be the non-observable effect concentration (NOEC). TDOE mortality at 80 mg/L was significantly higher than the control, but did not increase further with higher concentrations. A good concentration-response was observed for percentages of malformed larva and from 80 mg/L on these percentages were significantly higher than the control. Therefore, probit analysis gave a 144.6 mg/L TC50. At 120 and 140 mg/L, many larvae were plurimalformed. The most frequent alterations observed were abnormal gut coiling, microphthalmia, monolateral anophthalmia, and narrowing eyes. The histological screening mainly revealed ocular malformations such as double retina, retina nervous cell layer coiling, and altered lens. Moreover severe vacuolisation and necrosis were scored in liver and axial musculature. These results strongly support the assumption that TDOE is a powerful teratogen for X. laevis.     

Toxicity of zinc oxide nanoparticles in the earthworm, Eisenia fetida and subcellular fractionation of Zn

The extensive use of nanoparticles (NPs) in a variety of applications has raised great concerns about their environmental fate and biological effects. This study examined the impact of dissolved organic matter (DOM) and salts on ZnO NP dispersion/solubility and toxicity to the earthworm Eisenia fetida. To be able to better evaluate the toxicity of NPs, exposure in agar and on filter paper was proposed for enabling a comparison of the importance of different uptake routes. A dose-related increase in mortality was observed in earthworms exposed in agar with almost 100% mortality after 96 h exposure to the highest concentration (1000 mg ZnO/kg agar). Scanning electron microscopy (SEM) showed that the addition of salts enhanced the aggregation of ZnO NPs in agar and consequently affected the dissolution behavior and biological availability of the particles. On filter paper, mortality was the highest at the lowest exposure concentration (50 mg ZnO/L) and seemed to decrease with increasing exposure levels. TEM images of ZnO showed that the solubility and morphology of NPs were changed dramatically upon the addition of humic acids (HA). The subcellular distribution pattern of Zn in earthworms after 96 h exposure in agar and on filter paper showed that the Zn taken up via dietary ZnO particles (from agar) was mainly found in organelles and the cytosol while the Zn accumulated as soluble Zn from filter paper was mainly distributed in cell membranes and tissues. Antioxidant enzymatic activities (SOD, CAT, and GSH-px) were investigated in the worms surviving the toxicity tests. A slight increase of SOD activities was observed at the lowest exposure dose of ZnO (50mg/kg), followed by a decrease at 100mg/kg in the agar cubes. Activities of both CAT and GSH-Px enzymes were not significantly influenced in the worms exposed to agar, although a slight decrease at 500 and 1000 mg ZnO/kg agar was observed. A similar change trend of SOD activities was observed for the earthworms on filter paper, but a significant decrease began at a higher ZnO NP concentration of 500 mg ZnO/L. The use of soil extracts instead of deionized water (DW) to simulate a realistic exposure system significantly reduced the toxicity of the ZnO NPs on filter paper, which increases the predictive power of filter paper toxicity tests for the environmental risk assessment of NPs.     

Organic compounds in tire particle induce reactive oxygen species and heat-shock proteins in the human alveolar cell line A549

Debris produced from the attrition of tires of motor vehicles constitutes 5-7% of the atmospheric particulate matter (PM10). Debris particles are indeed small enough to enter human lung and thus morphological and chemical characterization has been performed. We demonstrated that the organic fraction of tire debris induces a dose-dependent increase in cell mortality, DNA damage, as well as a significant modification of cell morphology at the dose of 60 microg/ml, which may correspond to the quantity present in the air humans inhale daily. The present research aims at investigating if reactive oxygen species (ROS) production and Hsp70 expression are involved in the cascade of toxic effects produced on the A549 cell line, as it has been suggested for the ultrafine atmospheric particles and diesel exhaust. To this end, cells were exposed at the doses of 10, 50, 60, 75 microg/ml of TD organic extract (TDOE) and analyzed at different exposure time. ROS were detected by the oxidation of 2'7'-dichlorodihydrofluorescein diacetate to dichlorofluorescein, and fluorescence was measured by flow cytometry. Hsp70 protein expression was determined by immunochemical analysis, and protein expression quantification performed by optical densitometry. ROS production was analysed after 2 h of treatment. A statistically significant increase in fluorescence was observed and the intensity of the stress response was parallel to the increasing concentrations used. An evident increase of Hsp70 expression at lower doses (10, 50 microg/ml) and at longer exposure times (72 h) was observed, during the time that our previous studies showed that cell viability, plasma membrane integrity, and DNA molecules were not affected. Thus it can be deduced that the increase in Hsp70 expression protected the cells from those damages, which became evident at the higher doses, and that this parameter might be used as a sensitive indicator of exposure. These data suggest that ROS production may be the first event caused by A549 exposure to TDOE and this result is in line with other evidences provided for the role of ROS generation in ultrafine PM toxicity. It can be suggested that this event induces an overexpression of Hsp70 only at the lower doses and longer exposure time, when cells still appear unaffected. Subsequently when ROS generation reaches high levels, a general inhibition of protein synthesis probably occurs, culminating in cell toxicity.     

Removal of copper from water using limestone filtration technique. Determination of mechanism of removal

This paper discusses heavy metal removal from wastewater by batch study and filtration technique through low-cost coarse media. Batch study has indicated that more than 90% copper (Cu) with concentration up to 50 mg/l could be removed from the solution with limestone quantity above 20 ml (equivalent to 56 g), which indicates the importance of limestone media in the removal process. This indicates that the removal of Cu is influenced by the media and not solely by the pH. Batch experiments using limestone and activated carbon indicate that both limestone and activated carbon had similar metal-removal efficiency (about 95%). Results of the laboratory-scale filtration technique using limestone particles indicated that above 90% removal of Cu was achieved at retention time of 2.31 h, surface-loading rate of 4.07 m3/m2 per day and Cu loading of 0.02 kg/m3 per day. Analyses of the limestone media after filtration indicated that adsorption and absorption processes were among the mechanisms involved in the removal processes. This study indicated that limestone can be used as an alternative to replace activated carbon.     

纳米羟基磷灰石修复硫铁矿区镉锌复合污染土壤的效果研究

选取典型硫铁矿区周边受Cd和Zn复合污染黄壤为研究对象,采用淋溶试验和老化试验,探索添加羟基磷灰石对土壤中重金属生物有效性以及形态分布的影响,羟基磷灰石添加比例(w/w)设置为0%(CK)、1%(P1)、3%(P3)和5%(P5)。结果表明:(1)添加羟基磷灰石能够显著提高淋滤液的pH值,明显降低土壤中Cd和Zn淋失量,P1、P3和P5与CK的Cd累积淋失量(120μg)相比可分别降低74.2%、85.0%、92.0%,与CK的Zn累积淋失量(16.7 mg)相比可分别降低79.4%、92.1%、97.9%;(2)添加羟基磷灰石能够显著提高土壤pH值,P1、P3和P5的pH值分别比CK升高了0.64、0.85、1.20个pH单位;(3)添加羟基磷灰石能够显著降低土壤有效态Cd和Zn(0.025 M HCl提取),相较于CK,P1、P3和P5的有效态Cd含量可分别降低74.2%、96.8%、98.4%,有效态Zn含量可分别降低68.1%、96.6%、99.5%;(4)添加羟基磷灰石能够显著降低土壤可交换态和碳酸盐结合态Cd和Zn含量,增加土壤中残渣态Cd和Zn含量,从而促进Cd和Zn向非活性态转化。本研究证明了羟基磷灰石在西南典型硫铁矿区土壤重金属污染修复中有较大的应用潜力。     

Determination of heavy metal concentrations in street dusts in Istanbul E-5 highway

Components and quantity of street dust are environmental pollution indicators especially in big cities. Street dust is generally composed of car exhaust gas originated particles and wind-transported particles. Heavy metals, which are found in street dust, such as Pb, Cu, Mn, Zn, Cd and Ni are significant for environmental pollution. According to the kind of vehicle in traffic, quantity and type of heavy metals vary in street dust. The use of leaded gasoline gives a boost to the importance of lead level especially in street dust even at the start of 21st century. These metals possess bioaccumulation property, and the possibility of the amount of these metals reaching a critical value and threatening human health increases the importance of this issue. In this study, street dusts have been collected from E-5 Highway from Topkapi to Avcilar regions that spans about 18 km in Istanbul, Turkey, and Pb, Cu, Mn, Zn, Cd and Ni concentrations have been detected in street dust. Twenty-two street dust samples were taken from a total of 22 different points at previously decided 14 main areas. Analyses were conducted using Leeds Public Analyst method. According to the results of this study, Pb, Cu and Zn concentrations in E-5 Highway between Topkapi and Avcilar region in Istanbul were higher than maximum concentration levels of these heavy metals in normal soil. This situation indicates that there is heavy metal pollution in the inspected area in E-5 Highway in Istanbul.     

涪江上游泥石流灾损土地特征及典型流域淤积危险性研究

涪江上游以高山峡谷为主,人地矛盾突出,泥石流灾损土地是山区居民选择的主要生产生活场所。通过野外调查,初步查明目前涪江上游泥石流灾损土地以淤高的发展趋势为主,灾损土地扇形完整性程度达58%,以中等易发为主;大部分灾损土地距离主河距离为100~350 m,距离适中,水热条件良好。基于不同降雨频率条件下泥石流主沟内泥深、流量差异性,建立泥石流灾损土地的淤积危险范围确定方法;快速得到南坝窖子沟20 a一遇、50 a一遇、100 a一遇3种降雨频率条件下泥石流淤积危险范围,分别为0.167 km~2、0.292 km~2、0.420 km~2。为下一步建立基于土地潜力和灾害风险两个指标的灾损土地资源化潜力评估方法,探索泥石流灾损土地资源化利用模式,提供基础条件,并为山区居民进行土地利用提供快速指导。     

南京地区农田土壤和蔬菜重金属污染状况研究

采集了南京市5县4郊5个环境单元（矿冶区、交通干线、工厂周边、污灌地、农产品基地）共100个样点的农田土壤及部分蔬菜样品,测定了重金属（Pb、Cu、Zn、Cd）的质量分数。结果表明,土壤Pb、Cu、Zn、Cd 质量分数的变化范围分别为26.1~4 138.8、16.5 ~3 375.1、46.0~3 587.6、0.09~17.61 mg/kg。不同功能区土壤重金属含量存在明显差异,以矿区周边农田污染最为严重,其次为污灌地和公路沿线农田, 部分农产品基地存在轻度Cd污染,工厂周边农田土壤污染相对较小。19个样点的青菜地上部重金属Pb、Cu、Zn、Cd质量分数的变化范围分别为0.11~7.11、5.04~76.42、36.8~364.3、0.04~2.96 mg/kg,同样以矿区周边污染农田的青菜样本重金属含量最高。青菜重金属含量与土壤重金属生物有效性含量和总量之间呈极显著相关。不合理的矿业开采和冶炼是导致南京地区农田土壤和蔬菜重金属污染的重要原因。     

Evaluation of the strength characteristics of cement-stabilized clay–crumb rubber mixtures for its sustainable use in geotechnical applications

The proper disposal of discarded waste tires is becoming a serious matter of concern worldwide as huge proportion of this waste is being generated which makes the proper disposal virtually infeasible. About 1000 million of waste tires are discarded every year, and by the year 2030, it will turn up to 1200 million per year. If this enormous quantum of waste remains unattended, it would led to serious health and environmental problems. The investigation aims at appraising the compaction and strength characteristics of clayey soil incorporated with waste crumb rubber and cement for its sustainable use in geotechnical application. A series of unconfined compression strength and split tensile strength tests were carried out on clayey soil incorporated with two percentages of cement (3 and 6%) by weight and four percentages of crumb rubber (2.5, 5.0, 7.5, and 10.0%) by weight. Moreover, scanning electron microscope analysis was also carried out to get better intuition about the behaviour of the composite. Test results suggested that crumb rubber (up to 5%) could be mixed with uncemented/cemented clay soil with the congruent impression. The inclusion of discarded waste tires in cemented clay would be one of the congenial methods for the disposal of this waste as it substantially reduces the deleterious influence of waste tire disposal on human health and ecology.     

Effect of elemental sulphur on solubility of soil heavy metals and their uptake by maize

A pot experiment was conducted to study the influence of elemental sulphur (S) on solubility of soil Pb, Zn and Cd and uptake by maize (Zea mays L.). Two rates of elemental sulphur (S) applied at 0 (S0) and 200 (S200) mmol kg(-1) soil with three rates of each heavy metal at Pb, 0 (Pb0), 200 (Pb200), 400 (Pb400) mg kg(-1) soil, Zn, 0 (Zn0), 100 (Zn100), 200 (Zn200) mg kg(-1) soil and Cd, 0 (Cd0), 50 (Cd50), 100 (Cd100) mg kg(-1) soil, respectively. The result showed that with S application at 200 mmol S kg(-1), soil pH decreased about 0.3 unit and the solubility of the Zn and Cd was significantly increased, but the solubility of Pb had no significant influence. The concentration of Pb, Zn and Cd in maize shoots and roots were increased with increasing rates of heavy metals. However, the concentration of Zn and Cd in shoots and roots were higher with application of S rather than without S but no significant difference was found for Pb. The highest concentration of Zn in the shoots was 2.3 times higher with application of S rather than without at the same rate of Zn, 200 mg kg(-1). Plant biomass was also significantly affected by the application of S and of heavy metals. With heavy metal addition, the shoot and root biomass were decreased with the rates of those of heavy metals increased either with or without application of S. However, the shoot biomass was significantly decreased with S application at the same rate of heavy metals except that with Zn addition. The removal of Cd and Pb by maize uptake and accumulation with application of S had no significant increase compared to that without, but the removal Zn by maize uptake from the soil increased by application of S, 90.9 microg plant(-1) contrast to 25.7 microg plant(-1) at Zn200 within a growth period of only 40 days.     

Effect of cement content and recycled rubber particle size on the performance of rubber-modified concrete

According to the Rubber Manufacturer’s Association, the United States generated 3664 thousand metric tons of scrap tires in 2015. While most waste tires are repurposed, approximately 409.5 thousand metric tons were disposed in landfills. This study investigates an alternative use of the waste tires as a replacement of natural aggregates in concrete mixtures. This study investigated fresh concrete properties and compressive strength. Different coarse and fine aggregate rubber particle sizes were evaluated: 19-mm tire chips (TCs) and 30-mesh crumb rubber (CR). TCs were used to replace coarse aggregates, while CR was used to replace fine aggregate in the concrete mixtures in increments of 10% by volume. Concrete strength loss was reduced with a fine aggregate replacement with CR as opposed to greater losses of strength exhibited by a coarse aggregate replacement with TCs. Adequate strengths were achieved at replacement levels as high as 40% by volume with CR, whereas satisfactory strengths were achieved with only a 10% replacement of coarse aggregates with TCs. Acceptable strengths were obtained from mixtures utilizing a combination of the two rubber sizes. Cement content was observed to have greater influence on rubberized concrete compressive strength at lower rubber contents than higher levels.     

Equilibrium,kinetics and thermodynamics studies on adsorptive removal of cobalt ions from wastewater using MIL-100(Fe)

This study describes experiments in which MIL-100(Fe) was used to remove Co²⁺ ions from the waste water. The synthesised adsorbent was characterised by Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction, Brunauer–Emmett–Teller (BET) and scanning electron microscope. Statistical analysis was used to investigate the effects of different parameters. From the obtained results, the removal efficiency was enhanced with increasing contact time and pH but decreased with increasing cobalt initial concentration. The maximum removal efficiency of Co⁺² was 93.4% under optimum conditions. The equilibrium adsorption data were best fitted to linearly transformed Freundlich isotherm. Adsorption kinetic data followed the pseudo second-order kinetic model. The maximum adsorption capacity of Co⁺² on to the MIL-100(Fe) was found to be 119 mg g^?1. The results showed that ?G of adsorption was negative, while ?H was positive which showed that the adsorption process was spontaneous and endothermic. The positive value of ?S showed that disordering and randomness increased at the solid–solution interface of cobalt ions with MIL-100(Fe) particles.     

Comparative chronic toxicity of nanoparticulate and ionic zinc to the earthworm Eisenia veneta in a soil matrix

Manufactured nanoparticles (NPs) are increasingly being used in a range of consumer products and are already entering the environment. NP ZnO is one of the most widely used and potentially toxic NPs in aquatic exposures. It is likely that ZnO nanoparticles will also be bioavailable to soil organisms, studies on ZnO NP toxicity in a soil matrix are lacking. We exposed the earthworm Eisenia veneta to uncoated NP ZnO (<100 nm) dosed to soil and food at 250 and 750 mg Zn kg(-1) for 21 d. Concurrent exposures of equivalent ionic Zn were conducted with ZnCl(2) and for both forms effects on life history traits, immune activity and Zn body concentrations were compared. Despite slightly higher measured body concentrations, NP ZnO generally had less impact than ZnCl(2) on measured traits. At 750 mg Zn kg(-1), reproduction declined by 50% when exposed to NP ZnO but was almost completely inhibited by ZnCl(2). Similarly, immune activity was unaffected by NP ZnO but was suppressed by 20% when exposed to ZnCl(2). Scanning electron microscopy analysis of worm tissues following 24h aqueous exposure showed the presence of ZnO particles suggesting that NPs can be taken up in particulate form. This may explain the reduced effects at similar body concentrations seen in the soil study. Our findings suggest that risk assessments do not need to go beyond considering the metal component of NP ZnO in soils at least for the larger size uncoated particles considered here.     

Kinetics of trace element uptake and release by particles in estuarine waters: effects of pH,salinity, and particle loading

The uptake and release of 109Cd, 51Cr, 60Co, 59Fe, 54Mn, and 65Zn were studied using end-member waters and particles from Port Jackson estuary, Australia. The kinetics of adsorption and desorption were studied as a function of suspended particulate matter (SPM) loading and salinity. Batch experiments showed that the position and slope of the pH edges are dependent on the metal and on the salinity of the water (except for Mn). The general effect of salinity was to move the adsorption edge to higher pH values, with the greatest change being found for Cd. Most of the metals showed relatively simple kinetics with an increase in uptake as a function of time and suspended particle concentrations. The time dependence of Cd uptake was more complex, with an initial adsorption phase being followed by strong mobilization from the suspended sediments, explained by chlorocomplexation and competition with seawater major cations. The reversibility of the sorption decreased in the order Co>Mn>Zn>Cd>Fe>Cr. The percentage of adsorbed metal released in desorption experiments was greater in seawater than freshwater for Cd, Zn, and Co. These results are important in understanding the cycling of pollutants in response to pH, salinity, and particle concentrations in estuarine environments. In addition, they give valuable insight into the important mechanisms controlling the partitioning of heavy metals in the Port Jackson estuary.     

Cadmium desorption in sand

Desorption of cadmium (Cd) from sand was studied by both batch and flow-through methods. Batch experiments were conducted at three pH values (5.5, 6.0 and 6.5). In each case, the amount of Cd desorbed was low compared with the quantity of Cd adsorbed previously. Desorption of Cd in the batch experiments can be described adequately by a Freundlich isotherm. The Freundlich isotherm coefficient, Kf, increased with pH. Hysteresis between the sorption/desorption isotherms was observed in all batch experiments. Flow-through experiments in soil columns were conducted for the same three pH values, with the results used to determine transport and sorption/desorption parameters. Again, the desorption isotherms bore little resemblance to the corresponding adsorption isotherms. The experimental breakthrough curves were well fitted by a nonequilibrium desorption model, however the time scale of the desorption process was much larger than measured in batch experiments. This model was therefore rejected as lacking realism. A simple linear retardation (including hysteresis) model that utilises different isotherms was found to simulate column breakthrough curves well. The Freundlich isotherm coefficients, Kf, in all batch and flow-through desorption experiments were different to values evaluated from the corresponding adsorption experiments. However, in contrast to adsorption, desorption in flow-through experiments was not noticeably affected by changes in pH. The effect of pore-water velocity on desorption was also studied at pH 6.0. No trend was established between flow velocity and the desorption coefficient.     

Robustness testing of a free-fall triboelectric separation process for plastic waste recovery

Among the separation techniques used in industries, the triboelectric separation of insulating particles using a rotary tube is an effective way employed in the waste recovery of plastic and mineral products. This process, also called free-fall triboelectric separation, is widely used for the sorting of granular mixtures resulting from industrial plastic wastes. Given that the robustness of such a separation process is an important issue, a standard procedure is used for determining the set point and for minimising the process sensitivity of sorting mixed particles of different polymers to changes in the values of some critical factors. The aim of this paper was to analyse the efficiency of the triboelectric separation process of polymers with respect to any slight variation in the values of the most significant factors. Experiments with a sample of high-density polyethylene and polyvinyl chloride plastic granules were carried out on a laboratory experimental bench. Several one-factor-at-a-time experiments, followed by two factorial designs (one composite and the other fractional), were performed based on the following experimental procedure: (1) determination of the variation limits of the input variables; (2) identification of the set point and (3) robustness testing of the process, i.e. testing whether the performance of the system remains high even when the factors vary slightly around the set point.     

Environmental externalities in relation to agricultural sector in Thailand with trade-linked analysis

Thailand plays an important role in the international trade of food and agricultural products, which is in alignment with its national strategy of serving as the “kitchen of the world.” When looking at its agricultural promotion and export policies, the country only counts the value gains from exports while neglecting environmental externalities related to plantation practices. The purpose of this study was to perform a trade-off analysis between consumptive water, land, and fertilizer use together with the economic values of major crops for export and consumption in the country. The results show that to gain income from agricultural exports, the country has exploited various natural resources. The area used to harvest rice, sugarcane, cassava, and rubber adds up to approximately 15.3 million ha: 7.2 million ha of which is for domestic consumption and 8.1 ha for export. To produce Thailand’s agricultural exports, total water use is estimated to be 49.8–67.5 billion m³ per year (61–65 %), while the amount used to produce crops for domestic consumption is 26.5–43.7 billion m³ per year (35–39 %). Meanwhile, 1,056–1,826 thousand tons (54 %) of fertilizer was used on crops for domestic consumption, and 1,222–1,370 thousand tons (46 %) of fertilizer was used on export crops. The best crop choice for export in terms of its export value, land use, fertilizer use, and water consumption is rubber. The worst crop choices for export are rice and cassava. More sustainable agricultural practices are needed to effect improvements such as increased yields and reduced fertilizer and water use.     

Kinetics of dissolution of Chernobyl fuel particles in soil in natural conditions

Kinetic of fuel particles dissolution under natural environmental conditions has been investigated using the data on (90)Sr speciation in soils collected from 1995 to 1997 within the Chernobyl nuclear power plant 50 km zone. The dependency of fuel particles dissolution constants on the soil acidity (pH = 4-7) has been obtained on the basis of large and statistically reliable experimental data. Results show that between 2 and 21% of (90)Sr activity is associated with weathering resistant fuel particles. Therefore, these particles would not influence the radiological situation in the near future. The map of the main agrochemical characteristics and the map of the fuel particles dissolution constants have been created for the 30-km zone territory. According to the prognosis of dynamics of fuel particles dissolution in the investigated zone, a radiological situation along the fuel paths of radioactive fallout in present time reached a stable state. An increasing in absolute contents of (90)Sr mobile forms in neutral soils will be observed in the next 10-20 yr. However, the difference between the maximum level of mobile forms contents and their existing contents will not exceed 20%.     

Distribution and dissipation pathways of nonylphenol polyethoxylates in the Yellow River: Site investigation and lab-scale studies

Spatial distribution of nonylphenol polyethoxylates (NPEOs) and nonylphenol (NP) was investigated in a field study in Lanzhou Reach of the Yellow River. NPEOs and their metabolites were found in the river, with the maximum dissolved concentrations of 6.38 nmol/L for NPEOs, 0.19 nmol/L for nonylphenol ethoxy acetic acids (NPECs) and 0.79 nmol/L for NP, respectively. The maximum concentrations in the sediment and suspended particle samples were 1.50 and 5.09 nmol/g for NPEOs and NP, respectively. The effects of particles, light and microorganism on the dissipation of NPEOs in the river water were investigated based on lab-scale experiments. When natural particles were removed, 72% and 22% degradation of NPEOs were achieved at 120 h in non-sterile and sterile conditions with light, respectively. Different concentrations of NPECs were also observed in these experiments. When suspended particle matters (SPMs) were present, about 38-50% of NPEOs were sorbed to the particulate phase in only 1 h. As a result, the degradation of NPEOs and production of NPECs were inhibited. However, the combined sorption and degradation in the presence of SPMs resulted in lower dissolved NPEO concentrations than those in the absence of SPMs. Biodegradation was the most important pathway for NPEOs degradation in the river water, while NPECs seemed to be produced through both biological and abiological pathways.     

Soil-water distribution coefficients and plant transfer factors for (134)Cs, (85)Sr and (65)Zn under field conditions in tropical Australia

Measurements of soil-to-plant transfer of (134)Cs, (85)Sr and (65)Zn from two tropical red earth soils ('Blain' and 'Tippera') to sorghum and mung crops have been undertaken in the north of Australia. The aim of the study was to identify factors that control bioaccumulation of these radionuclides in tropical regions, for which few previous data are available. Batch sorption experiments were conducted to determine the distribution coefficient (K(d)) of the selected radionuclides at pH values similar to natural pH values, which ranged from about 5.5 to 6.7. In addition, K(d) values were obtained at one pH unit above and below the soil-water equilibrium pH values to determine the effect of pH. The adsorption of Cs showed no pH dependence, but the K(d) values for the Tippera soils (2300-4100 ml/g) exceeded those for the Blain soils (800-1200 ml/g) at equilibrium pH. This was related to the greater clay content of the Tippera soil. Both Sr and Zn were more strongly adsorbed at higher pH values, but the K(d) values showed less dependence on the soil type. Strontium K(d)s were 30-60 ml/g whilst Zn ranged from 160 to 1630 ml/g for the two soils at equilibrium pH. With the possible exception of Sr, there was no evidence for downward movement of radionuclides through the soils during the course of the growing season. There was some evidence of surface movement of labelled soil particles. Soil-to-plant transfer factors varied slightly between the soils. The average results for sorghum were 0.1-0.3 g/g for Cs, 0.4-0.8 g/g for Sr and 18-26 g/g for Zn (dry weight) with the initial values relating to Blain and the following values to Tippera. Similar values were observed for the mung bean samples. The transfer factors for Cs and Sr were not substantially different from the typical values observed in temperate studies. However, Zn transfer factors for plants grown on both these tropical soils were greater than for soils in temperate climates (by more than an order of magnitude). This may be related to trace nutrient deficiency and/or the growth of fungal populations in these soils. The results indicate that transfer factors depend on climatic region together with soil type and chemistry and underline the value of specific bioaccumulation data for radionuclides in tropical soils.