Chemical Composition of Fine Particles in the Tennessee Valley Region

ABSTRACT

Fine particles in the atmosphere have elicited new national ambient air quality standards (NAAQS) because of their potential role in health effects and visibility-reducing haze. Since April 1997, Tennessee Valley Authority (TVA) has measured fine particles (PM_2.5) in the Tennessee Valley region using prototype Federal Reference Method (FRM) samplers, and results indicate that the new NAAQS annual standard will be difficult to meet in this region. The composition of many of these fine particle samples has been determined using analytical methods for elements, soluble ions, and organic and elemental carbon. The results indicate that about one-third of the measured mass is SO₄ ^-2, one-third is organic aerosol, and the remainder is other materials. The fraction of SO₄ ^-2 is highest at rural sites and during summer conditions, with greater proportions of organic aerosol in urban areas throughout the year. Additional measurements of fine particle mass and composition have been made to obtain the short-term variability of fine mass as it pertains to human exposure. Measurements to account for semi-volatile constituents of fine mass (nitrates, semi-volatile organics) indicate that the FRM may significantly under-measure organic constituents. The potentially controllable anthropogenic fraction of organic aerosols is still largely unknown.     

Chemical composition of fine particles in the Tennessee Valley region

Fine particles in the atmosphere have elicited new national ambient air quality standards (NAAQS) because of their potential role in health effects and visibility-reducing haze. Since April 1997, Tennessee Valley Authority (TVA) has measured fine particles (PM2.5) in the Tennessee Valley region using prototype Federal Reference Method (FRM) samplers, and results indicate that the new NAAQS annual standard will be difficult to meet in this region. The composition of many of these fine particle samples has been determined using analytical methods for elements, soluble ions, and organic and elemental carbon. The results indicate that about one-third of the measured mass is SO4(-2), one-third is organic aerosol, and the remainder is other materials. The fraction of SO4(-2) is highest at rural sites and during summer conditions, with greater proportions of organic aerosol in urban areas throughout the year. Additional measurements of fine particle mass and composition have been made to obtain the short-term variability of fine mass as it pertains to human exposure. Measurements to account for semi-volatile constituents of fine mass (nitrates, semi-volatile organics) indicate that the FRM may significantly under-measure organic constituents. The potentially controllable anthropogenic fraction of organic aerosols is still largely unknown.     

Regional contributions to airborne particulate matter in central California during a severe pollution episode

The externally-mixed source-oriented UCD/CIT air quality model was applied to determine the significance of inter-regional transport for primary and secondary particulate matter (PM) in California's Central Valley during a severe wintertime PM pollution episode from December 15, 2000 to January 7, 2001. The gases and primary PM emitted from eight different geographical sub-regions were tracked separately in a model simulation that included transport, physical and chemical transformation and deposition processes. The model results directly predict the contribution that each sub-region makes to PM concentrations throughout the entire model domain. The boundary layer was relatively stagnant during the simulated 3-week air quality episode, and no consistent transport pattern for primary PM was predicted. Several significant inter-regional transport events were identified that each lasted a few days. Each of these inter-regional events was characterized by transport of gas-phase precursors of nitrate that combined with local emissions of ammonia to produce particulate nitrate. Nitrate already in the particle phase was not transported efficiently due to higher dry deposition rates for particles relative to gas-phase nitrogen oxides. The distinctive pattern of transport for nitrate precursors reflects the relatively long timescales required to convert NO_x emissions to nitrate during winter conditions characterized by low temperatures, weak photolysis rates, and low oxidant concentrations. The equilibrium partitioning of nitrate and ammonia to the particle phase is relatively fast once the nitrate has been produced. The most-likely transport distance for nitrate during the current episode varied from 130–140 km for the northern portion of the Central Valley to 50–60 km in the southern portion of the Central Valley. Sub-regions further south in the Valley have smaller transport distances because of slower wind speeds and the greater abundance of ammonia in these areas, leading to faster conversion of gas-phase reactive nitrogen into particulate nitrate, which has a higher dry deposition rate than the gas-phase species. The most-likely transport distance for primary organic compounds (OC) was found to be less than that for nitrate, varying from 50 to 60 km for the northern portion of the Valley to 20–30 km for southern portion of the Valley. Overall, 68% of the particulate nitrate formed in the most polluted sub-regions of the Central Valley originates from emissions in those same sub-regions. Local emissions controls should therefore provide an effective strategy to reduce airborne particulate matter concentrations to acceptable levels.     

Wintertime Vertical Variations in Particulate Matter (PM) and Precursor Concentrations in the San Joaquin Valley during the California Regional Coarse PM/Fine PM Air Quality Study

Abstract

Air quality monitoring was conducted at a rural site with a tower in the middle of California’s San Joaquin Valley (SJV) and at elevated sites in the foothills and mountains surrounding the SJV for the California Regional PM₁₀/M_2.5 Air Quality Study. Measurements at the surface and on a tower at 90 m were collected in Angiola, CA, from ecember 2000 through February 2001 and included hourly black carbon (BC), particle counts from optical particle counters, nitric oxide, ozone, temperature, relative humidity, wind speed, and direction. Boundary site measurements were made primarily using 24-hr integrated particulate matter (PM) samples. These measurements were used to understand the vertical variations of PM and PM precursors, the effect of stratification in the winter on concentrations and chemistry aloft and at the surface, and the impact of aloft-versus-surface transport on PM concentrations. Vertical variations of concentrations differed among individual species. The stratification may be important to atmospheric chemistry processes, particularly nighttime nitrate formation aloft, because NO₂ appeared to be oxidized by ozone in the stratified aloft layer. Additionally, increases in accumulation-mode particle concentrations in the aloft layer during a fine PM (PM_2.5) episode corresponded with increases in aloft nitrate, demonstrating the likelihood of an aloft nighttime nitrate formation mechanism. Evidence of local transport at the surface and regional transport aloft was found; transport processes also varied among the species. The distribution of BC appeared to be regional, and BC was often uniformly mixed vertically. Overall, the combination of time-resolved tower and surface measurements provided important insight into PM stratification, formation, and transport.     

Transport of atmospheric fine particulate matter: part 1--findings from recent field programs on the extent of regional transport within North America

Air quality field data, collected as part of the fine particulate matter Supersites program and other field measurements programs, have been used to assess the role of aerosol transport, over length scales of approximately 100-1000 km, on fine particulate matter concentrations. Assessment of data from New York, NY; Baltimore, MD; Pittsburgh, PA; Atlanta, GA; Houston, TX; St. Louis, MO; and Fresno, CA, indicates that in virtually all of the regions, transport of aerosol over distances of 100-1000 km has a significant impact on urban particulate matter concentrations and a dominant role in determining rural particulate matter concentrations, though the nature of the regional contributions differs from region to region. This assessment is generally consistent with previous conceptual models of fine particulate matter formation and accumulation in these regions. The nature of the transported aerosol is largely sulfate in Eastern and Midwestern cities and nitrate in the Central Valley of California. In addition to physical transport of aerosol over distances of 100-1000 km, regional transport of aerosol precursors may lead to conditions conducive to large-scale nucleation events. Regional nucleation events have been reported in the East, Midwest, and in California. The events occurred in the morning soon after surface layers coupled with layers aloft, and the events generate ultrafine particles. In some cases, these nucleation events have been correlated with availability of sulfur dioxide and, therefore, may be sulfate formation events.     

Second Generation Chemical Mass Balance Source Apportionment of Sulfur Oxides and Sulfate at the Grand Canyon during the Project MOHAVE Summer Intensive

ABSTRACT

Receptor-based chemical mass balance (CMB) analysis techniques are designed to apportion species that are conserved during pollutant transport using conserved source profiles. The techniques will fail if non-conservative species (or profiles) are not properly accounted for in the CMB model. The straightforward application of the CMB model developed for Project MOHAVE using regional profiles resulted in a significant under-prediction of total sulfate oxides (SO_x, SO₂ plus fine particulate sulfate) for many samples at Meadview, AZ. In addition, for these samples the concentration of the inert tracer emitted from the MOHAVE Power Project (MPP), ocPDCH, was also under-predicted. A second-generation model has been developed which assumes that separation of particles and SO₂ can occur in the MPP plume during nighttime stable plume conditions. This second-generation CMB model accounts for all SO_x present at the various receptor sites. In addition, the concentrations of ocPDCH and the presence of other inert tracers of emission from regional sources are accurately predicted. The major source of SO_x at Meadview was the MPP, but the major source of sulfate at this site was the Las Vegas urban area. At Hopi Point in the Grand Canyon, the Baja California region (Imperial Valley and northwestern Mexico) was the major source of both SO_x and sulfate.     

Transport and transformation of sulfur compounds over East Asia during the TRACE-P and ACE-Asia campaigns

On the basis of the recently estimated emission inventory for East Asia with a resolution of 1×1°, the transport and chemical transformation of sulfur compounds over East Asia during the period of 22 February through 4 May 2001 was investigated by using the Models-3 Community Multi-scale Air Quality (CMAQ) modeling system with meteorological fields calculated by the regional atmospheric modeling system (RAMS). For evaluating the model performance simulated concentrations of sulfur dioxide (SO₂) and aerosol sulfate (SO₄²⁻) were compared with the observations on the ground level at four remote sites in Japan and on board aircraft and vessel during the transport and chemical evolution over the Pacific and Asian Pacific regional aerosol characterization experiment field campaigns, and it was found that the model reproduces many of the important features in the observations, including horizontal and vertical gradients. The SO₂ and SO₄²⁻ concentrations show pronounced variations in time and space, with SO₂ and SO₄²⁻ behaving differently due to the interplay of chemical conversion, removal and transport processes. Analysis of model results shows that emission was the dominant term in regulating the SO₂ spatial distribution, while conversion of SO₂ to SO₄²⁻ in the gas phase and the aqueous phase and wet removal were the primary factors that controlled SO₄²⁻ amounts. The gas phase and the aqueous phase have the same importance in oxidizing SO₂, and about 42% sulfur compounds (25% in SO₂) emitted in the model domain was transported out, while about 57% (35% by wet removal processes) was deposited in the domain during the study period.     

Determination of the source areas contributing to regionally high warm season PM2.5 in eastern North America

An ensemble-trajectory analysis technique known as Quantitative Transport Bias Analysis was applied to determine which geographic areas systematically contributed to above- and below-average fine particle mass (PM2.5) over eastern North America. Six-hour average measurements from 12 rural or suburban locations in eastern North America collected using a tapered element oscillating microbalance were individually associated with corresponding 3-day back-trajectories for the warm seasons (May-September) of 2000 and 2001. Much of the populated areas of northeastern North America were implicated in the build-up of PM2.5 to above-average concentrations. The finer structure of the Quantitative Transport Bias Analysis pattern indicated that transport from the Ohio River Valley, particularly the eastern portion of this area, was most often associated with the highest PM2.5 concentrations. In addition, air masses originating over a relatively large area from southeast Ohio to the western part of Virginia and the western Kentucky to central Tennessee area tended to result in relatively high PM2.5 concentrations over northeastern North America. These observation-based findings were consistent with the spatial distribution of the main sulfur dioxide emissions sources and the major oxides of nitrogen point sources.     

PM2.5 chemical source profiles for vehicle exhaust, vegetative burning, geological material, and coal burning in Northwestern Colorado during 1995

PM_2.5 (particles with aerodynamic diameters less than 2.5 μm) chemical source profiles applicable to speciated emissions inventories and receptor model source apportionment are reported for geological material, motor vehicle exhaust, residential coal (RCC) and wood combustion (RWC), forest fires, geothermal hot springs; and coal-fired power generation units from northwestern Colorado during 1995. Fuels and combustion conditions are similar to those of other communities of the inland western US. Coal-fired power station profiles differed substantially between different units using similar coals, with the major difference being lack of selenium in emissions from the only unit that was equipped with a dry limestone sulfur dioxide (SO₂) scrubber. SO₂ abundances relative to fine particle mass emissions in power plant emissions were seven to nine times higher than hydrogen sulfide (H₂S) abundances from geothermal springs, and one to two orders of magnitude higher than SO₂ abundances in RCC emissions, implying that the SO₂ abundance is an important marker for primary particle contributions of non-aged coal-fired power station contributions. The sum of organic and elemental carbon ranged from 1% to 10% of fine particle mass in coal-fired power plant emissions, from 5% to 10% in geological material, >50% in forest fire emissions, >60% in RWC emissions, and >95% in RCC and vehicle exhaust emissions. Water-soluble potassium (K⁺) was most abundant in vegetative burning profiles. K⁺/K ratios ranged from 0.1 in geological material profiles to 0.9 in vegetative burning emissions, confirming previous observations that soluble potassium is a good marker for vegetative burning.     

Potential contribution of sulfate production in cumulus cloud droplets to ground level particle sulfur concentrations

The relationships have been examined between the presence or absence of cumulus clouds and 3rd quarter fine particle sulfur concentrations in St Louis. An association between the presence of cumulus clouds with SO₂ conversions in droplets and incrementally higher fine particle sulfur concentrations can be demonstrated. However, diurnal patterns of fine particle sulfur concentrations in the presence of cumulus clouds are not consistent with local contributions from sulfate formation in cumulus clouds. Morning fog often occurs on the same days on which cumulus clouds form later. Reactions of SO₂ in fog droplets appear to make a contribution, but do not account for the major part of the increments in fine particle sulfur concentrations associated with cumulus clouds. The variations in fine particle sulfur concentrations observed can be explained if a substantial part of the sulfate formed in cumulus is transported upwards from the planetary boundary layer into the lower free troposphere. Subsequent multiday regional scale horizontal transport with concurrent gradual vertical transport of sulfate down to the surface would be consistent with the observed results.     

Wintertime vertical variations in particulate matter (PM) and precursor concentrations in the San Joaquin Valley during the California Regional Coarse PM/Fine PM Air Quality Study

Air quality monitoring was conducted at a rural site with a tower in the middle of California's San Joaquin Valley (SJV) and at elevated sites in the foothills and mountains surrounding the SJV for the California Regional PM10/ PM2.5 Air Quality Study. Measurements at the surface and n a tower at 90 m were collected in Angiola, CA, from December 2000 through February 2001 and included hourly black carbon (BC), particle counts from optical particle counters, nitric oxide, ozone, temperature, relative humidity, wind speed, and direction. Boundary site measurements were made primarily using 24-hr integrated particulate matter (PM) samples. These measurements were used to understand the vertical variations of PM and PM precursors, the effect of stratification in the winter on concentrations and chemistry aloft and at the surface, and the impact of aloft-versus-surface transport on PM concentrations. Vertical variations of concentrations differed among individual species. The stratification may be important to atmospheric chemistry processes, particularly nighttime nitrate formation aloft, because NO2 appeared to be oxidized by ozone in the stratified aloft layer. Additionally, increases in accumulation-mode particle concentrations in the aloft layer during a fine PM (PM2.5) episode corresponded with increases in aloft nitrate, demonstrating the likelihood of an aloft nighttime nitrate formation mechanism. Evidence of local transport at the surface and regional transport aloft was found; transport processes also varied among the species. The distribution of BC appeared to be regional, and BC was often uniformly mixed vertically. Overall, the combination of time-resolved tower and surface measurements provided important insight into PM stratification, formation, and transport.     

Sources and chemical composition of atmospheric fine and coarse particles in the Helsinki area

During April 1996–June 1997 size-segregated atmospheric aerosol particles were collected at an urban and a rural site in the Helsinki area by utilising virtual impactors (VI) and Berner low-pressure impactors (BLPI). In addition, VI samples were collected at a semi-urban site during October 1996–May 1997. The average PM_2.3 (fine particle) concentrations at the urban and rural sites were 11.8 and 8.4 μg/m³, and the PM_2.3−15 (coarse particle) concentrations were 12.8 and about 5 μg/m³, respectively. The difference in fine particle mass concentrations suggests that on average, more than one third of the fine mass at the urban site is of local origin. Evaporation of fine particle nitrate from the VI Teflon filters during sampling varied similarly at the three sites, the average evaporation being about 50–60%.The average fine particle concentrations of the chemical components (25 elements and 13 ions) appeared to be fairly similar at the three sites for most components, which suggests that despite the long-range transport, the local emissions of these components were relatively evenly distributed in the Helsinki area. Exceptions were the average fine particles Ba, Fe, Sb and V concentrations that were clearly highest at the urban site pointing to traffic (Ba, Fe, Sb) and to combustion of heavy fuel oil (V) as the likely local sources. The average coarse particle concentrations for most components were highest at the urban site and lowest at the rural site.Average chemical composition of fine particles was fairly similar at the urban and rural sites: non-analysed fraction (mainly carbonaceous material and water) 43% and 37%, sulphate 21% and 25%, crustal matter 12% and 13%, nitrate 12% and 11%, ammonium 9% and 10% and sea-salt 2.5% and 3.2%, respectively. At the semi-urban site also, the average fine particle composition was similar. At the urban site, the year round average composition of coarse particles was dominated by crustal matter (59%) and the non-analysed components (28%, mainly carbonaceous material and water), while the other contributions were much lower: sea-salt 7%, nitrate 4% and sulphate 2%. At the rural site, the coarse samples were collected in spring and summer and the percentage was clearly lower for crustal matter (37%) and sea-salt (3%) but higher for the not-analysed fraction (51%). At the semi-urban site, the average composition of coarse particles was nearly identical to that at the urban site.Correlations between the chemical components were calculated separately for fine and coarse particles. In urban fine particles sulphate, ammonium, Tl, oxalate and PM_2.3 mass correlated with each other and originated mainly from long-range transport. The sea-salt ions Na⁺, Cl⁻ and Mg²⁺ formed another group and still another group was formed by the organic anions oxalate, malonate, succinate, glutarate and methane sulphonate. Ni and V correlated strongly pointing to combustion of heavy fuel oil as the likely source. In addition, some groups with lower correlations were detected. At the rural and semi-urban sites, the correlating components were rather similar to those at the urban site, although differences were also observed.     

Rural ozone in the southeastern United States

Ozone measurements are reported for five rural sites in the Tennessee Valley region of the southeastern U.S. for periods ranging from 18 to 83 months during the years 1977 through 1984. Rural ozone (O₃) levels were found to equal or exceed urban values for the same region. The daily maximum 1-h average concentration was found to peak during the summer months, while the 24-h average concentrations were greatest in the spring. The annual cycle of daily maximum concentrations is related to the seasonal photochemical cycle. The annual cycle in 24-h average concentrations is best explained by the combined effects of the annual cycles in solar intensity and noctural O₃ depletion. There was no indication that stratospheric intrusions exhibited a significant influence on the annual O₃ cycles. Evidence was found for elevated O₃ levels during touchdown of plumes from large power plants. No long-term trend in rural O₃ concentrations, either daily maxima or means, was discernible.     

The regional nature of PM2.5 episodes in the upper Ohio River Valley

From October 1999 through September 2000, particulate matter (PM) with aerodynamic diameter > or =2.5 microm (PM2.5) mass and composition were measured at the National Energy Technology Laboratory Pittsburgh site, with a particle concentrator Brigham Young University-organic sampling system and a tapered element oscillating microbalance (TEOM) monitor. PM2.5 measurements had also been obtained with TEOM monitors located in the Pittsburgh, PA, area, and at sites in Ohio, including Steubenville, Columbus, and Athens. The PM data from all these sites were analyzed on high PM days; PM2.5 TEOM particulate mass at all sites was generally associated with transitions from locally high barometric pressure to lower pressure. Elevated concentrations occurred with transport of PM from outside the local region in advance of frontal passages as the local pressure decreased. During high-pressure periods, concentrations at the study sites were generally low throughout the study region. Further details related to this transport were obtained from surface weather maps and estimated back-trajectories using the hybrid single-particle Lagrangian integrated trajectory model associated with these time periods. These analyses indicated that transport of pollutants to the Pittsburgh site was generally from the west to the southwest. These results suggest that the Ohio River Valley and possible regions beyond act as a significant source of PM and its precursors in the Pittsburgh area and at the other regional sites included in this study.     

Modeling air quality during the California Regional PM10/PM2.5 Air Quality Study (CPRAQS) using the UCD/CIT source-oriented air quality model – Part III. Regional source apportionment of secondary and total airborne particulate matter

A comprehensive air quality modeling project was carried out to simulate regional source contributions to secondary and total (=primary + secondary) airborne particle concentrations in California's Central Valley. A three-week stagnation episode lasting from December 15, 2000 to January 7, 2001, was chosen for study using the air quality and meteorological data collected during the California Regional PM₁₀/PM_2.5 Air Quality Study (CRPAQS). The UCD/CIT mechanistic air quality model was used with explicit decomposition of the gas phase reaction chemistry to track source contributions to secondary PM. Inert artificial tracers were used with an internal mixture representation to track source contributions to primary PM. Both primary and secondary source apportionment calculations were performed for 15 size fractions ranging from 0.01 to 10 μm particle diameters. Primary and secondary source contributions were resolved for fugitive dust, road dust, diesel engines, catalyst equipped gasoline engines, non-catalyst equipped gasoline engines, wood burning, food cooking, high sulfur fuel combustion, and other anthropogenic sources.Diesel engines were identified as the largest source of secondary nitrate in central California during the study episode, accounting for approximately 40% of the total PM_2.5 nitrate. Catalyst equipped gasoline engines were also significant, contributing approximately 20% of the total secondary PM_2.5 nitrate. Agricultural sources were the dominant source of secondary ammonium ion. Sharp gradients of PM concentrations were predicted around major urban areas. The relative source contributions to PM_2.5 from each source category in urban areas differ from those in rural areas, due to the dominance of primary OC in urban locations and secondary nitrate in the rural areas. The source contributions to ultra-fine particle mass PM_0.1 also show clear urban/rural differences. Wood smoke was found to be the major source of PM_0.1 in urban areas while motor vehicle sources were the major contributor of PM_0.1 in rural areas, reflecting the influence from two major highways that transect the Valley.     

Second generation chemical mass balance source apportionment of sulfur oxides and sulfate at the Grand Canyon during the Project MOHAVE summer intensive

Receptor-based chemical mass balance (CMB) analysis techniques are designed to apportion species that are conserved during pollutant transport using conserved source profiles. The techniques will fail if non-conservative species (or profiles) are not properly accounted for in the CMB model. The straightforward application of the CMB model developed for Project MOHAVE using regional profiles resulted in a significant under-prediction of total sulfate oxides (SOx, SO2 plus fine particulate sulfate) for many samples at Meadview, AZ. In addition, for these samples the concentration of the inert tracer emitted from the MOHAVE Power Project (MPP), ocPDCH, was also under-predicted. A second-generation model has been developed which assumes that separation of particles and SO2 can occur in the MPP plume during nighttime stable plume conditions. This second-generation CMB model accounts for all SOx present at the various receptor sites. In addition, the concentrations of ocPDCH and the presence of other inert tracers of emission from regional sources are accurately predicted. The major source of SOx at Meadview was the MPP, but the major source of sulfate at this site was the Las Vegas urban area. At Hopi Point in the Grand Canyon, the Baja California region (Imperial Valley and northwestern Mexico) was the major source of both SOx and sulfate.     

Regional Transport and Urban Contributions to Fine Particle Concentrations in Southeastern Canada

Abstract

The impact of various atmospheric transport directions on ambient fine particle (PM_2.5) concentrations at several sites in southeastern Canada was estimated (for May-September) using back-trajectory analysis. Three-day back trajectories (four per day) were paired with 6-hr average PM_2.5 mass concentrations measured using tapered element oscillating microbalances (TEOM). PM_2.5 concentrations at rural locations in the region were affected by nonlocal sources originating in both Canada and the United States. Comparison of sites revealed that, on average, the local contribution to total PM_2.5 in the greater Toronto area (GTA) is approximately 30–35%. At each location, average PM_2.5 concentrations under south/southwesterly flow conditions were 2–4 times higher than under the corresponding northerly flow conditions. The chemical composition of both urban and rural PM_2.5 was determined during two separate 2-week spring/summer measurement campaigns. Components identified included SO₄ ^2?, NO₃ ^?, NH₄+, black carbon and organic carbon (OC), and trace elements. Higher particle mass at the urban Toronto site was composed of a higher proportion of all components. However, black carbon, NO₃ ^?, NaCl, and trace elements were found to be the most enriched over the rural/regional background levels.     

Resolving the interactions between population density and air pollution emissions controls in the San Joaquin Valley,USA

The effectiveness of emissions control programs designed to reduce concentrations of airborne particulate matter with an aerodynamic diameter <2.5 μm (PM_2.5) in California's San Joaquin Valley was studied in the year 2030 under three growth scenarios: low, medium, and high population density. Base-case inventories for each choice of population density were created using a coupled emissions modeling system that simultaneously considered interactions between land use and transportation, area source, and point source emissions. The ambient PM_2.5 response to each combination of population density and emissions control was evaluated using a regional chemical transport model over a 3-week winter stagnation episode. Comparisons between scenarios were based on regional average and population-weighted PM_2.5 concentrations. In the absence of any emissions control program, population-weighted concentrations of PM_2.5 in the future San Joaquin Valley are lowest under growth scenarios that emphasize low population density. A complete ban on wood burning and a 90% reduction in emissions from food cooking operations and diesel engines must occur before medium- to high-density growth scenarios result in lower population-weighted concentrations of PM_2.5. These trends partly reflect the fact that existing downtown urban cores that naturally act as anchor points for new high-density growth in the San Joaquin Valley are located close to major transportation corridors for goods movement. Adding growth buffers around transportation corridors had little impact in the current analysis, since the 8-km resolution of the chemical transport model already provided an artificial buffer around major emissions sources.

Assuming that future emissions controls will greatly reduce or eliminate emissions from residential wood burning, food cooking, and diesel engines, the 2030 growth scenario using “as-planned” (medium) population density achieves the lowest population-weighted average PM_2.5 concentration in the future San Joaquin Valley during a severe winter stagnation event.

Implications: The San Joaquin Valley is one of the most heavily polluted air basins in the United States that are projected to experience strong population growth in the coming decades. The best plan to improve air quality in the region combines medium- or high-density population growth with rigorous emissions controls. In the absences of controls, high-density growth leads to increased population exposure to PM_2.5 compared with low-density growth scenarios (urban sprawl).     

Loss of Particle Nitrate from Teflon Sampling Filters: Effects on Measured Gravimetric Mass in California and in the IMPROVE Network

Abstract

The extent of mass loss on Teflon filters caused by ammonium nitrate volatilization can be a substantial fraction of the measured particulate matter with an aerodynamic diameter less than 2.5 μm (PM_2.5)or 10 μm (PM₁₀) mass and depends on where and when it was collected. There is no straightforward method to correct for the mass loss using routine monitoring data. In southern California during the California Acid Deposition Monitoring Program, 30-40% of the gravimetric PM_2.5 mass was lost during summer daytime. Lower mass losses occurred at more remote locations. The estimated potential mass loss in the Interagency Monitoring of Protected Visual Environments network was consistent with the measured loss observed in California. The biased mass measurement implies that use of Federal Reference Method data for fine particles may lead to control strategies that are biased toward sources of fugitive dust, other primary particle emission sources, and stable secondary particles (e.g., sulfates). This analysis clearly supports the need for speciated analysis of samples collected in a manner that preserves volatile species. Finally, although there is loss of volatile nitrate (NO₃ ^?) from Teflon filters during sampling, the NO₃ ^? remaining after collection is quite stable. We found little loss of NO₃ ^? from Teflon filters after 2 hr under vacuum and 1 min of heating by a cyclotron proton beam.     

Comparison of sulfate and nitrate particle mass concentrations measured by IMPROVE and the CDN

The 1977 and 1990 Amendments to the Clean Air Act call for visibility and atmospheric deposition monitoring throughout the United States. We compare sulfate and nitrate particle mass concentrations measured by two regional air quality networks, the Interagency Monitoring of PROtected Visual Environments (IMPROVE) network and the Clean Air Status and Trends Network (CASTNet), or CASTNet Deposition Network (CDN). The intent of this comparison is to quantify bias that may be introduced from differences in the respective network's sampling protocols. A number of sampling protocol differences exist between the two networks that may lead to sampling bias, particularly for particle NO₃⁻. Observed differences between particle SO₄²⁻ mass concentrations reported by the two monitoring networks are generally small, yet statistically significant at many comparison sites. Differences between particle NO₃⁻ mass concentrations are substantial, statistically significant at nearly all comparison sites, and the bias magnitude varies by geographic region. Differences in particle NO₃⁻, based on data from monitoring sites selected for this comparison, are 40% in the west, 56% in the interior desert/mountain region, and −9% in the east, expressed as the IMPROVE mean subtracted from the CDN mean, as a percent of the IMPROVE mean. Comparisons are made using data from 23 locations where monitoring sites from IMPROVE and CDN are within approximately 50 km.