Optimizing booster chlorination in water distribution networks: a water quality index approach

The optimization of chlorine dosage and the number of booster locations is an important aspect of water quality management in distribution networks. Booster chlorination helps to maintain uniformity and adequacy of free residual chlorine concentration, essential for safeguarding against microbiological contamination. Higher chlorine dosages increase free residual chlorine concentration but generate harmful by-products, in addition to taste and odor complaints. It is possible to address these microbial, chemical, and aesthetic water quality issues through free residual chlorine concentration. Estimating a water quality index (WQI) based on regulatory chlorine thresholds for microbial, chemical, and aesthetics criteria can help engineers make intelligent decisions. An innovative scheme for maintaining adequate residual chlorine with optimal chlorine dosages and numbers of booster locations was established based on a proposed WQI. The City of Kelowna (BC, Canada) water distribution network served to demonstrate the application of the proposed scheme. Temporal free residual chlorine concentration predicted with EPANET software was used to estimate the WQI, later coupled with an optimization scheme. Preliminary temporal and spatial analyses identified critical zones (relatively poor water quality) in the distribution network. The model may also prove useful for small or rural communities where free residual chlorine is considered as the only water quality criterion.     

Detection of seasonal variations in surface water quality using discriminant analysis

In the study, discriminant analysis (DA) was applied to water quality data set monitored in winter and summer months along 3 years to investigate seasonal variations of Tahtali Reservoir water quality. The variables were divided into two categories as “parameters naturally found in surface waters—Al, Fe, Mn, F, Ba, Cl, and SO₄” and “pollutants—biochemical oxygen demand, chemical oxygen demand, and NO₃”. Linear discriminant functions were calculated to distinguish between winter and summer samples. Results revealed that water quality variables (naturally found in surface water and also pollutants) were distinctly different between two seasons. Seasonal changes of water quality caused by anthropogenic activities should be taken into consideration by the water managers especially in summer seasons in which higher concentrations were observed. The study showed that DA can be applied successfully to establish the seasonal variation in surface water quality and make it possible to design a future temporal sampling strategy in an optimal manner.     

Application of water quality indices and analysis of the surface water quality monitoring network in semiarid North-Central Chile

Surface water quality has increasing importance worldwide and is particularly relevant in the semiarid North-Central Chile, where agriculture and mining activities are imposing heavy pressure on limited water resources. The current study presents the application of a water quality index in four watersheds of the 29°-33°S realm for the period 1999-2008, based on the Canadian Council of Ministers for the Environment approach and the Chilean regulation for irrigation water quality. In addition, two modifications to the index are tested and a comprehensive characterization of the existing monitoring network is performed through cluster analysis. The basins studied show fairly good water quality in the overall, specially the Limarí basin. On the other hand, the lower index values were obtained for the headwaters of Elqui, associated with the El Indio mining district. The first modification of the indicator (i.e., to consider parameters differentially according to their effect on human health or the environment) did not produce major differences with respect to the original index, given the generally good water quality. The second modification (i.e., to consider as threshold values the more restrictive figures derived from a set of regulations) yielded important differences in the indicator values. Finally, an adequate characterization of the monitoring network was obtained. The results presented spatial coherence and the information can be used as a basis for the optimization of the monitoring network if required.     

Evaluating response surface designs for uncertainty analysis and prescriptive applications of a large-scale water quality model

Environmental models are often too large and cumbersome for effective use in regulatory decision making or in the characterization of uncertainty. This paper describes and compares four response surfaces that could complement a large-scale water quality model, the U.S. National Water Pollution Control Assessment Model (NWPCAM), in simulation and regulatory decision support applications. Results show that a physically based reduced-form model that exploits the mathematical structure of the underlying water quality model is a better predictor of policy-relevant outputs than the polynomial expansions that are frequently used in response surface studies.     

Assessment of anthropogenic influences on surface water quality in urban estuary, northern New Jersey: multivariate approach

Concentrations of selected heavy metals (Cd, Cr, Cu, Pb, Ni, Fe, and Zn), nutrients (NO ₃ ^? and NH₃), fecal coliform colonies, and other multiple physical–chemical parameters were measured seasonally from 12 locations in an urban New Jersey estuary between 1994 and 2008. Stepwise regression, principal component analysis, and cluster analysis were used to group water quality results and sampling locations, as well as to assess these data’s relationship to sewage treatment effluents and the distance to the mouth of the river. The BOD₅, NH₃, NO ₃ ^? and fecal coliform counts clustered as one group and positively correlated to the distances from treated effluent and the measures of magnitude at the discharge points. Dissolved solids and most metal species scored high along a single principal component axes and were significantly correlated with the proximity to the industrialized area. From these data, one can conclude that the effluent discharge has been a main source of anthropogenic input to the Hackensack River over the past 15 years. Therefore, the greatest improvement to water quality would come from eliminating the few remaining combined sewer overflows and improving the removal of nutrients from treated effluents before they are discharged into the creeks and river.     

Water quality assessment: surface water sources used for drinking and irrigation in Zaria,Nigeria are a public health hazard

We assessed the quality and pollution status of source surface waters in Zaria, Nigeria by monitoring the nature, cause and extent of pollution in Samaru stream, Kubanni River and Kubanni dam over a period of 10 months, between March and December 2002. A total of 228 water samples was collected from 12 sites and analysed for a total of ten physicochemical and one bacteriological quality indicators, using standard methods. Aesthetic water quality impairment parameters were also observed. The mean values of most water quality parameters were significantly higher (P < 0.05) in both the stream and river than in the dam. There was no significant correlation between faecal coliform counts (FCC) and water temperature (in the range 15–33°C); pH (5.77–7.32); and turbidity (1.4–567 NTU). The high FCC ranged from 2.0 × 10¹ to 1.6 × 10⁶ MPN/100 ml and exceeded the WHO standards for drinking water and water used for fresh-produce irrigation, and correlated positively (P < 0.05) with conductivity (in the range 68–1,029 μS/cm); TDS (10.0–70.0 mg/l); TSS (10.0–70.0 mg/l); Cl (7.5–181 mg/l); PO₄⁻P (0.01–0.41 mg/l); NO₃⁻N (0.6–3.8 mg/l) and BOD₅ (0.1–14.9 mg/l). The main pollution sources were municipal wastewater, stormwater runoffs, the ABU sewage treatment plant, abattoir effluents and irrigation farms treated with chemical fertilisers. We conclude that these water bodies are potentially hazardous to public health and that proper sewage treatment and river quality monitoring are needed to warn against hazards to public health.     

Comparative analysis of regional water quality in Canada using the Water Quality Index

The Canadian Council of Ministers for the Environment (CCME) has developed a Water Quality Index (WQI) to simplify the reporting of complex water quality data. This science-based communication tool tests multi-variable water data against numeric water quality guidelines and/or objectives to produce a single unit-less number that represents overall water quality. The CCME WQI has been used to rate overall water quality in spatial and temporal comparisons of site(s). However, it has not been used in a comparative-analysis of exposure sites to reference sites downstream of point source discharges. This study evaluated the ability of the CCME WQI to differentiate water quality from metal mines across Canada at exposure sites from reference sites using two different types of numeric water quality objectives: (1) the water quality guidelines (WQG) for the protection of freshwater aquatic life and (2) water quality objectives determined using regional reference data termed Region-Specific Objectives (RSO). The application of WQG to the CCME WQI was found to be a good tool to assess absolute water quality as it relates to national water quality guidelines for the protection of aquatic life, but had more limited use when evaluating spatial changes in water quality downstream of point source discharges. The application of the RSO to the CCME WQI resulted in assessment of spatial changes in water quality downstream of point source discharges relative to upstream reference conditions.     

Relationship between landscape characteristics and surface water quality

The effects of landscape characteristics on surface water quality were evaluated in terms of land-use condition, soil type and slope. The case area, the Chichiawan stream in the Wulin catchment in Taiwan, is Formosan landlocked salmon's natural habitat. Due to the agriculture behavior and mankind's activities, the water and environmental quality has gradually worsened. This study applied WinVAST model to predict hydrological responses and non-point source pollution (NPSP) exports in the Wulin catchment. The land-use condition and the slope of land surface in a catchment are major effect factors for watershed responses, including flows and pollutant exports. This work discussed the possible variation of watershed responses induced by the change of land-use condition, soil type and slope, etc. The results show that hydrological responses are highly relative to the value of Curve Number (CN); Pollutant exports have large relation to the average slope of the land surface in the Wulin catchment.     

A probabilistic water quality index for river water quality assessment: a case study

Available water quality indices have some limitations such as incorporating a limited number of water quality variables and providing deterministic outputs. This paper presents a hybrid probabilistic water quality index by utilizing fuzzy inference systems (FIS), Bayesian networks (BNs), and probabilistic neural networks (PNNs). The outputs of two traditional water quality indices, namely the indices proposed by the National Sanitation Foundation and the Canadian Council of Ministers of the Environment, are selected as inputs of the FIS. The FIS is trained based on the opinions of several water quality experts. Then the trained FIS is used in a Monte Carlo analysis to provide the required input-output data for training both the BN and PNN. The trained BN and PNN can be used for probabilistic water quality assessment using water quality monitoring data. The efficiency and applicability of the proposed methodology is evaluated using water quality data obtained from water quality monitoring system of the Jajrood River in Iran.     

Evaluation of surface water quality by using Canadian Council of Ministers of the Environment Water Quality Index (CCME WQI) method and discriminant analysis method: a case study Coruh River Basin

In this study, the water quality of the Coruh River Basin, which is located in the Eastern Black Sea Region of Turkey, was evaluated. The water quality data measurement results obtained by the State Hydraulic Works 26th Regional Directorate from four different sites over a course of 4 years between the years 2011 and 2014 in the Coruh River Basin were used as the data. In this study, the water quality was evaluated by using the Canadian Council of Ministers of the Environmental Water Quality Index (CCME WQI) method and discriminant analysis (DA). The water quality of the Coruh River Basin was calculated as 30.4 and 71.35 by using the CCME WQI and classified as “poor,” “marginal,” and “fair”. These values show that the water of the Coruh River Basin is degraded and under threat and its overall quality is not close to natural or desired levels. The monitoring sites were divided into two groups by the cluster analysis (CA). DA is a multivariate analysis technique used to divide individuals or objects into different groups and assign them into predetermined groups. As a result of DA, calcium (Ca) and sulfate (SO₄) were determined to be significant parameters in the determination of the water quality of the Coruh River Basin. The success of DA depends on the percentage of correct classification. As a result of the analysis, 23% of the parameters in the first measurement point, 69.2% of the parameters in the second and third measurement points, and 76.9% of the parameters in the fourth measurement point were classified correctly. Since the second measurement point is the discharge point of a copper mine, it can be said that the water quality parameters measured may provide accurate results in detecting pollution at this point.     

供水厂水质状况分析

通过对西江某供水厂的水源水与出厂水水质进行分析研究 ,可知供水厂的水处理效果主要表现在对降低出水的浊度、色度和总细菌数等指标上 ,对大部分水溶性物质的减少无效或效果较低。为保证和提高饮用水的安全性和水质 ,除需提高供水厂的水处理效果和能力外 ,根本出路在于从环境管理与立法等角度 ,加大对水源水的保护力度 ,减少对饮用水源的排污     

Micronucleus study of the quality and mutagenicity of surface water from a semi-arid region

The present study evaluated the mutagenic potential of surface water from the Lucrecia dam. The Tradescantia-micronucleus (Trad-MCN) test and CBMN assay in human peripheral blood lymphocytes were applied, corresponding to an in vivo and in vitro system, respectively. Heavy metals and some physicochemical properties were also measured. Water samples were collected in November 2009 (dry season) and May 2010 (rainy season) at three different points. Results of both assays for raw water showed positive responses for the points analyzed when compared to the negative control. The CBMN assay showed that diluted water was still able to induce a significant increase in micronucleus frequency. For both assays, the highest mean MN was observed in the dry season. Chemical analyses detected an increase in heavy metal levels at the sampling points and in the different seasons. These findings indicate the presence of genotoxins, such as heavy metals, in the water, which may be affecting the entire ecosystem, as well as human health. More prolonged monitoring is recommended in order to better characterize this public water supply.     

Development and sensitivity analysis of a global drinking water quality index

The UNEP GEMS/Water Programme is the leading international agency responsible for the development of water quality indicators and maintains the only global database of water quality for inland waters (GEMStat). The protection of source water quality for domestic use (drinking water, abstraction etc) was identified by GEMS/Water as a priority for assessment. A composite index was developed to assess source water quality across a range of inland water types, globally, and over time. The approach for development was three-fold: (1) Select guidelines from the World Health Organisation that are appropriate in assessing global water quality for human health, (2) Select variables from GEMStat that have an appropriate guideline and reasonable global coverage, and (3) determine, on an annual basis, an overall index rating for each station using the water quality index equation endorsed by the Canadian Council of Ministers of the Environment. The index allowed measurements of the frequency and extent to which variables exceeded their respective WHO guidelines, at each individual monitoring station included within GEMStat, allowing both spatial and temporal assessment of global water quality. Development of the index was followed by preliminary sensitivity analysis and verification of the index against real water quality data.     

Assessment of surface water quality using multivariate statistical techniques: a case study of Behrimaz Stream, Turkey

Multivariate statistical techniques, such as cluster analysis (CA), principal component analysis, and factor analysis, were applied for the evaluation of temporal/spatial variations and for the interpretation of a water quality data set of the Behrimaz Stream, obtained during 1 year of monitoring of 20 parameters at four different sites. Hierarchical CA grouped 12 months into two periods (the first and second periods) and classified four monitoring sites into two groups (group A and group B), i.e., relatively less polluted (LP) and medium polluted (MP) sites, based on similarities of water quality characteristics. Factor analysis/principal component analysis, applied to the data sets of the two different groups obtained from cluster analysis, resulted in five latent factors amounting to 88.32% and 88.93% of the total variance in water quality data sets of LP and MP areas, respectively. Varifactors obtained from factor analysis indicate that the parameters responsible for water quality variations are mainly related to discharge, temperature, and soluble minerals (natural) and nutrients (nonpoint sources: agricultural activities) in relatively less polluted areas; and organic pollution (point source: domestic wastewater) and nutrients (nonpoint sources: agricultural activities and surface runoff from villages) in medium polluted areas in the basin. Thus, this study illustrates the utility of multivariate statistical techniques for analysis and interpretation of data sets and, in water quality assessment, identification of pollution sources/factors and understanding temporal/spatial variations in water quality for effective stream water quality management.     

Statistical analyses of regional surface water quality in southeastern Ontario

Historical records from Ontario's Provincial Water Quality Monitoring Network (PWQMN) for rivers and streams were analyzed to assess the feasibility of mapping regional water quality patterns in southeastern Ontario which spans two major geologic zones, the Precambrian Shield and the St. Lawrence Lowlands, thus serving as a paradigm for much of Ontario. Despite biases toward the populated Lowlands and associated pollution problems, general spatial trends are evident via the analysis of intervariable relations, individual parameter maps and multivariate analysis. Using a robust algorithm designed to identify outliers and abstract underlying bivariate relations, a linear regional hardness-alkalinity relation was derived, where most anomalies proved to be mine drainage impacted sites. Regionally, multivariate ordination reveals that central tendencies of common indicators of ionic strength and nutrient richness correlate positively and that site clusters broadly reflect the transition from oligotrophic Shield waters to eutrophic conditions of heavily agricultural Lowland streams. Results suggest that on the Shield more precisely delineated aquatic regions may be realized by applying GIS to integrate river and synoptic lake survey data. Further synthesis with bedrock and surficial geology, physiography, pedology and other temporally invariant spatial attributes should yield regional patterns of background quality from which locally attainable water objectives might be defined. Additional synoptic surveys of sedimentary Lowland streams may be required as most available sites relflect anthropogenic pollution.     

Assessing BMP effectiveness: multiprocedure analysis of observed water quality data

Observed water quality data obtained from eight stream monitoring locations within Richland–Chambers Watershed in north central Texas were analyzed for trends using box-and-whisker plots, exceedance probability plots, and linear and Mann–Kendall statistical methods. Total suspended solids decreased at seven out of eight stations, and at two of these stations, the decrease was significant. Mixed results were obtained for nitrogen across the stations. A nonsignificant and significant increase in nitrite plus nitrate nitrogen (nitrite + nitrate N) was noticed in two stations each, whereas at the other four stations showed nonsignificant decrease. The results of organic nitrogen (Org N) was similar to nitrite + nitrate N except that the two stations that showed significant increase in nitrite + nitrate N showed nonsignificant decrease in Org N. Mixed results were also noticed for orthophosphorus (Ortho P) including nonsignificant decrease at two stations, significant decrease and increase at one station each, and nonsignificant increase in four stations. In general, total phosphorus (TP) decreased at all stations, significantly at some, except one station where it increased significantly. Decreasing trends in sediment, Org N, Ortho P, and TP were likely related to implementation of best management practices (BMPs). Increasing trends in dissolved constituents including Ortho P and nitrite + nitrate N were likely due to increased surface residue as a result of some BMPs such as conservation tillage.     

The SSC cycle: a PDCA approach to address site-specific characteristics in a continuous shallow water quality monitoring project

In any water quality-monitoring project there are several critical success factors that must be adequately addressed in order to ensure the implementation and realization of the monitoring objectives. Site selection is one of these critical success factors. The monitoring sites must be selected to comply with the monitoring and data quality objectives. In the real world, ideal monitoring setting conditions are difficult to achieve, and compromises must be made in order to locate the monitoring stations that best represent the environment to be monitored. Site-specific characteristics are all the environmental, logistical and management factors particular to the monitoring site, that could influence the fulfilment of the monitoring and data quality objectives. Therefore, during the site selection process, it is essential to properly consider and evaluate these site-specific characteristics. The SSC cycle was developed with this goal in mind, to assist the monitoring team to systematically address site-specific characteristics. The cycle is a methodology to organize the site-specific characteristics in different categories, and to ensure a comprehensive overview of these characteristics throughout the project life cycle.     

Reservoir water quality: a case from Jordan

Jordan relies heavily on reservoirs building and development to cope with water supply challenges, where monitoring and assessment of reservoir water quality are critically important for the sustainable use of these water supplies. Mujib Dam is an important water supply source in central western Jordan. Evaluation of water quality parameters and their spatial distributions (vertical and horizontal) showed near-neutral pH values with nearly similar values from surface to bottom. The vertical profile of DO and TDS in the dammed reservoir showed slight decreasing trends with increasing depth. Although Ca, Mg, Na, and K concentrations varied slightly with depths, their variations showed no trends. Similarly, the vertical and horizontal distribution patterns of Cl, SO₄, HCO₃, NO₃, and PO₄ in Mujib reservoir water showed insignificant variations in surface water layer and relatively unchanged values or decreasing trends through the water column. Higher values of TN have been observed, especially in the western part, suggesting that agricultural activities and livestock farming in the upstream catchment are impacting water quality. Results revealed that weathering and dissolution of rocks are the major source of water chemistry. The majority of trace metal levels (Cd, Cr, Cu, Fe, Mn, Pb, Zn, Co, Ni, Sr, and B) in water showed relatively similar surface and bottom values. The concentrations of COD and BOD₅ in surface water were relatively low with higher concentrations observed in the northwestern corner, coincided with higher levels of chlorophyll a. The average ratio of TN to TP in surface water suggests that phosphorus is the limiting factor for the algal blooms, whereas the average chlorophyll a level in surface water indicates oligo-mesotrophic water.