测定城市生活污泥中重金属的酸消解方法研究

采用HNO3-HC1O4-HF、HNO3-HC1O4、王水-HC1O4、HNO3等不同的酸消解方法对城市生活污泥进行消解。通过对这4种消解方法进行实验比较及对Cu、Ni、Zn三种金属元素浓度的测定,发现HNO3-HC1O4是适合城市生活污泥特点的消解方法。     

Comparative study of extraction methods for the determination of PAHs from contaminated soils and sediments

The following four methods were compared on the extraction efficiency of 16 EPA (US Environmental Protection Agency) polycyclic aromatic hydrocarbons (PAHs): German method of the Verband Deutscher Landwirtschaftlicher Untersuchungs und Forschungsanstalten (VDLUFA), two methods of the International Organization for Standardization using shaking (ISO A) and Soxhlet extraction (ISO B) and an ultrasonic method. Recovery rates of 16 PAHs were determined in two soils. Extraction efficiency was evaluated in five soils and three sediments. Effect of drying soils and sediments on extraction efficiency was tested using the VDLUFA and the ultrasonic methods. Our study shows that the number of aromatic rings, rather than extraction procedures, significantly influenced recovery rates of individual PAHs. No significant differences in extraction efficiency of the four methods were observed for less polluted samples. For highly polluted soils, extraction efficiency decreased in the following order: VDLUFA method > ISO A > ultrasonic method > ISO B. Influence of soil moisture on extraction efficiency depended to some extent on both solvent used and content of PAHs in samples. A mixture of dichloromethane/acetone (5:1) is recommended for PAH extraction from moist samples when the ultrasonic method is used.     

Observations of mercury wet deposition in Mexico

We provide a longer-term record of Hg wet deposition at two tropical latitude monitoring sites in Mexico, selected to provide regionally representative data. Weekly wet deposition samples were collected over 2 years, from September 2003 to November 2005. Based on this data set, we discuss the magnitude and seasonal variation of Hg in wet deposition and compare the results to other measurement sites and to several model estimates. With precipitation-weighted mean (PWM) concentrations of 8.2 and 7.9 ng L^?1, respectively, during the sampling period from Sep 30 2003 to Oct 11 2005, and median weekly concentrations of 9.4?±?1 ng L^?1 for both sites, the wet Hg concentrations and deposition at HD01 were much lower than those observed at the US Gulf Coast MDN sites while the wet Hg deposition at OA02 was much lower than most MDN sites, but somewhat similar to US MDN sites along the Pacific Coast. Based on the limited available data, we conclude that the approximately 30 % higher average precipitation at HD01 and roughly equal PWM concentrations lead to the higher deposition at HD01 versus OA02. We believe that these observations may offer scientists and modelers additional understanding of the depositional fluxes in the lower latitudes of North America.     

Comparative study of mercury speciation in commercial fishes of the Brazilian Amazon

Mercury is responsible for serious episodes of environmental pollution throughout the world, especially in the Amazon. This toxicity has led regulatory agencies to focus on fish as the target organism for protecting the health of humans and other sensitive organisms. Unfortunately, in the Amazon area, different sampling strategies and the wide variety of sampling areas and fish species make it extremely difficult to determine relationships across geographic regions or over time to ascertain historical trends. Thus, the aim of this work was to achieve three main objectives: a comparative study of mercury contamination in fish of Itaituba (Tapajós, located downstream of the largest gold-mining region in Amazon) and Belém (an area non-exposed to mercury pollution of anthropogenic origin), perform an analysis of inorganic mercury (IHg) versus monomethylmercury (MeHg) contents, and, finally, compare mercury contamination in Tapajós over time. Five piscivorous species were obtained in Itaituba and Belém. Also, four non-piscivorous species were collected in Itaituba. For the first time, mercury speciation showed that (1) current MeHg levels in piscivorous species in Tapajós are higher than those of the non-exposed area, (2) piscivorous species from Itaituba (dourada, filhote, and sarda) contained mercury levels above the World Health Organization safety limit (~17 %) and/or above the US Environmental Protection Agency tissue residue criterion (40 %), (3) increased MeHg is usually accompanied by increased IHg, and (4) the mean total mercury concentrations for piscivorous species in Itaituba were within the same range and, associated uncertainties as those previously reported, although a remarkable decreasing trend over time was observed for mean total Hg concentrations in non-piscivorous species from Itaituba. The present study supports the importance of continuous monitoring of both populations in the Amazon Rivers. Our results will better assist the development of preventive strategies and governmental actions to confront the problem of mercury contamination in the Amazon.     

Recurrence of fecal coliforms and Salmonella species in biosolids following thermophilic anaerobic digestion.

The U.S. Environmental Protection Agency (U.S. EPA) Part 503 Biosolids Rule requires the fecal coliform (indicator) or Salmonella species (pathogen) density requirements for Class A biosolids to be met at the last point of plant control (truck-loading facility and/or farm for land application). The three Southern Californian wastewater treatment plants in this study produced biosolids by thermophilic anaerobic digestion and all met the Class A limits for both fecal coliforms and Salmonella sp. in the digester outflow biosolids. At two plants, however, a recurrence of fecal coliforms was observed in postdigestion biosolids, which caused exceedance of the Class A limit for fecal coliforms at the truck-loading facility and farm for land application. Comparison of observations at the three plants and further laboratory tests indicated that the recurrence of fecal coliforms can possibly be related to the following combination of factors: (1) incomplete destruction of fecal coliforms during thermophilic anaerobic digestion, (2) contamination of Class A biosolids with fecal coliforms from external sources during postdigestion, (3) a large drop of the postdigestion biosolids temperature to below the maximum for fecal coliform growth, (4) an unknown effect of biosolids dewatering in centrifuges. At Hyperion Treatment Plant (City of Los Angeles, California), fecal coliform recurrence could be prevented by the following: (1) complete conversion to thermophilic operation to exclude contamination by mesophilically digested biosolids and (2) insulation and electrical heat-tracing of postdigestion train for maintaining a high biosolids temperature in postdigestion.     

Estimating contribution of precipitation scavenging of atmospheric particulate mercury to mercury wet deposition in Japan

Mercury wet deposition is dependent on both the scavenging of divalent reactive gaseous mercury (RGM) and atmospheric particulate mercury (Hg(p)) by precipitation. Estimating the contribution of precipitation scavenging of RGM and Hg(p) is important for better understanding the causes of the regional and seasonal variations in mercury wet deposition. In this study, the contribution of Hg(p) scavenging was estimated on the basis of the scavenging ratios of other trace elements (i.e., Cd, Cu, Mn, Ni, Pb and V) existing entirely in particulate form. Their wet deposition fluxes and concentrations in air, which were measured concurrently from April 2004 to March 2005 at 10 sites in Japan, were used in this estimation. The monthly wet deposition flux of mercury at each site correlated with the amount of monthly precipitation, whereas the Hg(p) concentrations in air tended to decrease during summer. There was a significant correlation (P<0.001) among the calculated monthly average scavenging ratios of trace elements, and the values in each month at each site were similar. Therefore, it is assumed the monthly scavenging ratio of Hg(p) is equivalent to the mean value of other trace elements. Using this scavenging ratio (W), the wet deposition flux (F) due to Hg(p) scavenging in each month was calculated by F=WKP, where K and P are the Hg(p) concentration and amount of precipitation, respectively. Relatively large fluxes due to Hg(p) scavenging were observed at a highly industrial site and at sites on the Japan Sea coast, which are strongly affected by the local sources and the long-range transport from the Asian continent, respectively. However, on average, at the 10 sites, the contribution of Hg(p) scavenging to the annual mercury deposition flux was 26%, suggesting that mercury wet deposition in Japan is dominated by RGM scavenging. This RGM should originate mainly from the in situ oxidation of Hg⁰ in the atmosphere.     

湿法脱硫系统中液相二价汞的还原抑制

湿法脱硫系统协同脱汞是当前燃煤烟气脱汞的重要方法,而进入脱硫系统的二价汞还原问题会降低汞的脱除效率,从而限制该方法的使用。在脱硫浆液中添加添加剂捕集和稳定二价汞能有效抑制二价汞的还原。在模拟浆液条件下考察多硫化钙、TMT、乙基黄原酸钠、EDTA和腐殖酸对液相二价汞的还原抑制效果。结果表明,多硫化钙和TMT能极大的抑制二价汞的还原,当其添加量分别为0.004%(体积分数)和0.002%(体积分数)时,汞还原量仅为未添加条件下的3.3%和0.8%,而乙基黄原酸钠、EDTA和腐殖酸在一定条件下不仅不会抑制二价汞的还原,反而会一定程度促进二价汞的还原。这表明乙基黄原酸钠、EDTA和腐殖酸并不适合于作为液相二价汞的还原抑制剂。     

Performance evaluation of a 'sequential-batch' temperature-phased anaerobic digestion (TPAD) scheme for producing Class A biosolids.

Laboratory studies were conducted to evaluate the performance and operational stability of a Temperature-Phased Anaerobic Digestion (TPAD) system modified to operate in the sequential-batch mode. The system fed with a 40:60 mixture (dry weight) of primary sludge (PS) and waste activated sludge (WAS) at 5.5% solids showed stable performance with minimum variation in operational parameters such as biogas production, VFA to alkalinity ratio, pH, and foam accumulation at system retention times as short as 12 days. The maximum volatile solids removal (VSR) of 52.5% was achieved at a system retention time of 16 days. The system did not show any effects of "shock loading" at the retention times studied and outperformed a "conventional" mesophilic system operated at a longer retention time. The system was effective in reducing the densities of pathogenic indicator organisms in the biosolids to levels lower than those specified by U.S. EPA for Class A designation.     

Technological options for the management of biosolids

BACKGROUND, AIM, AND SCOPE: Large quantities of biosolids (sewage sludge), which are produced from municipal wastewater treatment, are ever-increasing because of the commissioning of new treatment plants and continuous upgrades of the existing facilities. A large proportion of biosolids are currently landfilled. With increasing pressure from regulators and the general public, landfilling of biosolids is being phased out in many countries because of potential secondary pollution caused by leachate and the emission of methane, a potent greenhouse gas. Biosolids contain nutrients and energy that can be used beneficially. Significant efforts have been made recently to develop new technologies to manage biosolids and make useful products from them. In this paper, we provide a review of the technologies in biosolids management. MATERIALS AND METHODS: A survey of literature was conducted. RESULTS: At present, the most common beneficial use of biosolids is agricultural land application because of inherent fertilizer values found in biosolids. Expansion of land application, however, may be limited in the future because of more stringent regulatory requirements and public concern about food chain contamination in some countries. Perceived as a green energy source, the combustion of biosolids has received renewed interest. Anaerobic digestion is generally a more effective method than incineration for energy recovery, and digested biosolids are suitable for further beneficial use through land application. Although conventional incineration systems for biosolid management generally consume more energy than they produce because of the high moisture content in the biosolids, it is expected that more combustion systems, either monocombustion or cocombustion, will be built to cope with the increasing quantity of biosolids. DISCUSSION: Under the increasingly popular low-carbon economy policy, biosolids may be recognized as a renewable fuel and be eligible for 'carbon credits'. Because ash can be used to manufacture construction materials, combustion can provide a complete management for biosolids. A number of advanced thermal conversion technologies (e.g., supercritical water oxidation process and pyrolysis) are under development for biosolids management with a goal to generate useful products, such as higher quality fuels and recovery of phosphorus. With an ever-increasing demand for renewable energy, growing bioenergy crops and forests using biosolids as a fertilizer and soil amendment can not only contribute to the low-carbon economy but also maximize the nutrient and carbon value of the biosolids. CONCLUSIONS: Land application of biosolids achieves a complete reuse of its nutrients and organic carbon at a relatively low cost. Therefore, land application should become a preferred management option where there is available land, the quality of biosolids meet regulatory requirements, and it is socially acceptable. Intensive energy cropping and forest production using biosolids can help us meet the ever-increasing demand for renewable energy, which can eliminate the contamination potential for food sources, a common social concern about land application of biosolids. In recent years, increasing numbers of national and local governments have adopted more stringent regulations toward biosolid management. Under such a political climate, biosolids producers will have to develop multireuse strategies for biosolids to avoid being caught because a single route management practice might be under pressure at a short notice. Conventional incineration systems for biosolids management generally consume more energy than they produce and, although by-products may be used in manufacturing, this process cannot be regarded as a beneficial use of biosolids. However, biosolids are likely to become a source of renewable energy and produce 'carbon credits' under the increasingly popular, low-carbon economy policy. RECOMMENDATIONS AND PERSPECTIVES: To manage biosolids in a sustainable manner, there is a need for further research in the following areas: achieving a higher degree of public understanding and acceptance for the beneficial use of biosolids, developing cost-efficient and effective thermal conversions for direct energy recovery from biosolids, advancing technology for phosphorus recovery, and selecting or breeding crops for efficient biofuel production.     

饮用水源突发性铬污染去除方法的比较研究

通过对水源水中铬污染的不同去除方法的比较实验及验证实验,研究pH值、FeSO_4、NaHSO_3和活性炭的投加量对铬的去除效果的影响。实验结果表明,当原水中铬的含量为0.5 mg/L时,未调节pH值的条件下,亚硫酸氢钠与活性炭对铬的最高去除率为50%左右;硫酸亚铁还原沉淀在FeSO_4·7H_2O:Cr~(6+)投加比=16:1时,滤后出水中Cr~(6+)的去除率达到96.8%,中试出水中未检出Cr~(6+),出水的总Cr、总Fe等指标完全达到《生活饮用水卫生标准》(GB 5749-2006)的要求。     

Comparative study of non-invasive methods for assessing Daphnia magna embryo toxicity

Embryos, unlike adults, are typically sessile, which allows for an increase in the available metrics that can be used to assess chemical toxicity. We investigate Daphnia magna development rate and oxygen consumption as toxicity metrics and compare them to arrested embryo development using four different techniques with potassium cyanide (KCN) as a common toxicant. The EC₅₀ (95 % CI) for arrested development was 2,535 (1,747–3,677) μg/L KCN. Using pixel intensity changes, recorded with difference imaging, we semi-quantitatively assessed a decrease in development rate at 200 μg/L KCN, threefold lower than the arrested development lowest observed effect concentration (LOEC). Respirometry and self-referencing (SR) microsensors were two unique techniques used to assess oxygen consumption. Using respirometry, an increase in oxygen consumption was found in the 5 μg/L KCN treatment and a decrease for 148 μg/L, but no change was found for the 78 μg/L KCN treatment. Whereas, with SR microsensors, we were able to detect significant changes in oxygen consumption for all three treatments: 5, 78, and 148 μg/L KCN. While SR offered the highest sensitivity, the respirometry platform developed for this study was much easier to use to measure the same endpoint. Oxygen consumption may be subject to change during the development process, meaning consumption assessment techniques may only be useful only for short-term experiments. Development rate was a more sensitive endpoint though was only reliable four of the six embryonic developmental stages examined. Despite being the least sensitive endpoint, arrested embryo development was the only technique capable of assessing the embryos throughout all developmental stages. In conclusion, each metric has advantages and limitations, but because all are non-invasive, it is possible to use any combination of the three.     

Multiresidue screening methods for the determination of pesticides in tomatoes

The possibility of applying thin layer chromatography (TLC) detection for the analysis of pesticide residues in tomatoes was investigated. Samples of tomatoes that have never been treated with pesticide were fortified with atrazine, carbaryl, carbofuran, chloroxuron, diuron, dimethoate, imazalil, oxamyl and methamidophos. The samples were extracted, cleaned-up by gel permeation chromatography and then applied on silica gel plates. The pesticides were eluted with ethyl acetate and dichloromethane. Two eluting solvent systems were tested, one using the reagents o-toluidine + potassium iodite (o-TKI) and the other p- nitrobenzene fluoroborate (NBFB). After the development of the plates, the diameter of the spots was measured. The lowest minimum detection quantity (MDQ) for o-TKI system for atrazine was 12 ng. The highest was 125 ng for carbofuran. Using NBFB system, the lowest MDQ was 60 ng for carbaryl and the highest was 70 ng obtained for carbofuran. Considering the concentration of these pesticides in the spiked tomato samples, the minimum concentration was 1.1 ng/microL and 32.3 ng/microL for atrazine and carbofuran, respectively, by using o-TKI system. For NBFB system the minimum concentration reached was 3.5 ng/microL and 4.3 ng/microL for carbaryl and carbofuran, respectively. This study showed that TLC can be used for semi-quantitative analysis.     

河流沉积物中微生物DNA的提取方法比较研究

提取河流沉积物中DNA是研究河流沉积物微生物多样性的难点之一,实验开发了一种酚与SDS的DNA提取方法,与OMEGA和BioDee 2种DNA提取试剂盒方法进行了比较,并通过DNA纯度、PCR扩增结合16S rDNA克隆文库检验对几种方法进行了评价.结果表明,OMEGA DNA提取试剂盒法方法简单,提取的DNA纯度较高...     

Estimate of the uncertainty in measurement for the determination of mercury in seafood by TDA AAS

An approach for the estimate of the uncertainty in measurement considering the individual sources related to the different steps of the method under evaluation as well as the uncertainties estimated from the validation data for the determination of mercury in seafood by using thermal decomposition/amalgamation atomic absorption spectrometry (TDA AAS) is proposed. The considered method has been fully optimized and validated in an official laboratory of the Ministry of Agriculture, Livestock and Food Supply of Brazil, in order to comply with national and international food regulations and quality assurance. The referred method has been accredited under the ISO/IEC 17025 norm since 2010. The approach of the present work in order to reach the aim of estimating of the uncertainty in measurement was based on six sources of uncertainty for mercury determination in seafood by TDA AAS, following the validation process, which were: Linear least square regression, Repeatability, Intermediate precision, Correction factor of the analytical curve, Sample mass, and Standard reference solution. Those that most influenced the uncertainty in measurement were sample weight, repeatability, intermediate precision and calibration curve. The obtained result for the estimate of uncertainty in measurement in the present work reached a value of 13.39%, which complies with the European Regulation EC 836/2011. This figure represents a very realistic estimate of the routine conditions, since it fairly encompasses the dispersion obtained from the value attributed to the sample and the value measured by the laboratory analysts. From this outcome, it is possible to infer that the validation data (based on calibration curve, recovery and precision), together with the variation on sample mass, can offer a proper estimate of uncertainty in measurement.     

SO2、NO对汞在湿法电除尘器中脱除的影响

湿法电除尘器(WESP)作为一种控制烟气中超细颗粒物的有效手段被应用于燃煤电厂的超低排放改造中,然而烟气中的Hg0受电场、水膜、烟气组分等因素的影响在WESP中的协同脱除机理尚不明确。为了深入了解该机理,探讨了WESP电场和水膜对Hg0的控制机理,并进一步研究了烟气中SO2、NO对Hg0在WESP中脱除的影响。结果表明：电场静电作用对烟气中Hg0脱除贡献较小,O2电离产物?O对Hg0的氧化作用是O2促进Hg0脱除的主要途径,水蒸气通过电离产生?OH促进Hg0氧化以及通过黏附作用促进Hg0脱除;水膜的裹挟作用对WESP系统Hg0的脱除贡献较小,溶于水中的汞不稳定且容易再释放;SO2、NO均通过在电场中电离产生?O促进Hg0氧化脱除,其中,SO2及其电离产物溶于水膜后可以与Hg2+形成稳定配合物抑制汞的再释放,而NO的电离产物在水膜中对汞再释放的抑制作用较小。     

Intercomparison of methods for sampling and analysis of atmospheric mercury species

An intercomparison for sampling and analysis of atmospheric mercury species was held in Tuscany, June 1998. Methods for sampling and analysis of total gaseous mercury (TGM), reactive gaseous mercury (RGM) and total particulate mercury (TPM) were used in parallel sampling over a period of 4 days. The results show that the different methods employed for TGM compared well whereas RGM and TPM showed a somewhat higher variability. Measurement results of RGM and TPM improved over the time period indicating that activities at the sampling site during set-up and initial sampling affected the results. Especially the TPM measurement results were affected. Additional parallel sampling was performed for two of the TPM methods under more controlled conditions which yielded more comparable results.     

微波消解-氢化物发生原子荧光光度法测定土壤中的汞

建立了微波消解-氢化物发生原子荧光光度法测定土壤中汞的方法。对微波消解条件、样品粒度等进行了优化,用3 mL硝酸和2 mL盐酸的混合酸作消解溶剂,在设定的微波条件下汞提取完全。用3%的盐酸作为反应载流,0.01%硼氢化钾与0.5%氢氧化钠的混合液为还原剂,直接定容后应用HG-AFS测定,通过测定国家标准参考物质和加标回...     

湿法烟气脱硫工艺中烟气再热方式的选择

分析了湿法烟气脱硫烟气再热原因,介绍了多种烟气再热方法,并对其进行了技术分析,为湿法烟气脱硫工程的烟气再热系统设计提供了依据。     

餐厨垃圾湿式厌氧消化最优有机负荷及失稳指标

为探究餐厨垃圾湿式厌氧消化最佳有机负荷及失稳预警指标,在(36±1) ℃单相连续搅拌条件下进行有机负荷(OLR)梯度实验。通过理论及数学分析确定90%含水率餐厨垃圾湿式厌氧消化的最佳OLR和失稳指标。当OLR（以VS计）为2.94 g?(L?d)-1时,挥发性固体去除率、甲烷产率、容积沼气产率分别为78%、0.58 L?g-1VS、2.99 L?(L?d)-1,此时厌氧反应器达到最佳运行状态。一定浓度的游离氨(FAN)会抑制微生物活性,触发挥发性脂肪酸(VFA)的积累,造成容积沼气产率降低,第36天,当OLR增至3.21 g?(L?d)-1时,FAN浓度升至区域峰值207 mg?L-1,但随后骤降35.9%（39 d）,分别造成VFA和挥发性脂肪酸浓度与碳酸氢盐碱度的比值(VFA/TA)从第37天的1 897 mg?L-1、0.22升高至第47天的4 755 mg?L-1、0.73,系统进入抑制稳定状态,最终导致容积沼气产率从第47天的2.66 L?(L?d)-1降至第48天的1.88 L?(L?d)-1,系统恶化。协同分析表明,当VFA和VFA/TA分别达到2 500 mg?L-1和0.35并出现持续上升的现象时,能提前7～8 d对90%含水率餐厨垃圾湿式厌氧消化系统的失稳提出预警。     

A diagnostic evaluation of modeled mercury wet depositions in Europe using atmospheric speciated high-resolution observations

This study is part of the Global Mercury Observation System (GMOS), a European FP7 project dedicated to the improvement and validation of mercury models to assist in establishing a global monitoring network and to support political decisions. One key question about the global mercury cycle is the efficiency of its removal out of the atmosphere into other environmental compartments. So far, the evaluation of modeled wet deposition of mercury was difficult because of a lack of long-term measurements of oxidized and elemental mercury. The oxidized mercury species gaseous oxidized mercury (GOM) and particle-bound mercury (PBM) which are found in the atmosphere in typical concentrations of a few to a few tens pg/m³ are the relevant components for the wet deposition of mercury. In this study, the first European long-term dataset of speciated mercury taken at Waldhof/Germany was used to evaluate deposition fields modeled with the chemistry transport model (CTM) Community Multiscale Air Quality (CMAQ) and to analyze the influence of the governing parameters. The influence of the parameters precipitation and atmospheric concentration was evaluated using different input datasets for a variety of CMAQ simulations for the year 2009. It was found that on the basis of daily and weekly measurement data, the bias of modeled depositions could be explained by the bias of precipitation fields and atmospheric concentrations of GOM and PBM. A correction of the modeled wet deposition using observed daily precipitation increased the correlation, on average, from 0.17 to 0.78. An additional correction based on the daily average GOM and PBM concentration lead to a 50 % decrease of the model error for all CMAQ scenarios. Monthly deposition measurements were found to have a too low temporal resolution to adequately analyze model deficiencies in wet deposition processes due to the nonlinear nature of the scavenging process. Moreover, the general overestimation of atmospheric GOM by the CTM in combination with an underestimation of low precipitation events in the meteorological models lead to a good agreement of total annual wet deposition besides the large error in weekly deposition estimates. Moreover, it was found that the current speciation profiles for GOM emissions are the main factor for the overestimation of atmospheric GOM concentrations and might need to be revised in the future. The assumption of zero emissions of GOM lead to an improvement of the mean normalized bias for three-hourly observations of atmospheric GOM from 9.7 to 0.5, Furthermore, the diurnal correlation between model and observation increased from 0.01 to 0.64. This is a strong indicator that GOM is not directly emitted from primary sources but is mainly created by oxidation of GEM.