Thermal formation of PBDD/F from tetrabromobisphenol A--a comparison of polymer linked TBBP A with its additive incorporation in thermoplastics

For a long period, polybrominated flame retardants are under discussion because of the formation of polybrominated dibenzo-p-dioxins (PBDD)/dibenzofurans (PBDF) (PBDD/F) in case of thermal stress. Concerning polymer linked tetrabromobisphenol A (TBBP A), formation of PBDD/F was commonly presumed to be sterically hindered because of the covalent fixation into the polymer backbone. Combustion experiments with additively incorporated TBBP A compared with its polymer linkage revealed, that this assumption is incorrect and has to be revised. Under same conditions, similar PBDD/F concentrations in the range of 17.5-19.6 mg PBBD/F per kg TBBP A applied were analyzed. PBDD/F homologue distribution patterns were almost identical predominated by low brominated PBDF. These findings for PBDD/F formation have to be considered in future discussions regarding thermal stress caused by combustion or recycling processes, including other flame retardants bound in polymer matrix, e.g. polybrominated polystyrene (PS), or those with molecular structures showing less analogy to PBDD/F, like hexabromocyclododecane. The second aspect introduced, is the influence of different plastics on the formation rates of PBDD/F. In this context, combustion experiments were performed in an atmosphere consisting of synthetic air and HBr. PBDD/F concentrations were 8.47 mg/kg polyethylene, 1.67 mg/kg PS, 3.92 mg/kg phenolic resin and 18.1 mg/kg epoxy resin. Distribution patterns of PBDD/F homologues could partly be correlated with the occurrence of the precursors polybrominated benzenes and phenols.     

Post-combustion syntheses of PCDD/F and PBDD/F from halogen-rich fuel is suppressed by a pebble heater technology

GOAL, SCOPE AND BACKGROUND: Changes in German and European legislation shifted processing of polymer-rich shredding residues (SR) from landfill to thermal treatment. However, when waste of electric and electronic equipment (WEEE) is the source of SR, thermal treatment is complicated by halogens as well as the presence of polybrominated dioxins and furans (PBDD/F) and brominated flame retardants (BFR). Hence, WEEE requires high temperature incineration with sufficient residence times. Post-combustion synthesis of polyhalogenated dioxins and furans (PXDD/F) is dominant in the temperature range between 250-450 degrees C. Thus, a very rapid gas cooling from 450 degrees to 250 degrees C is important for proper raw gas treatment. The pebble heater technology developed by ATZ Entwicklungszentrum (Sulzbach-Rosenberg, Germany) might serve as an alternative to the state-of-the-art quench cooling. It is based on the application of a pebble bed of natural bulk material, which the exhaust gases flows through radially. It provides an excellent heat transfer and a temperature gradient in the range of 1,500-2,000 K/m. The paper presents data of a pilot application of the pebble heater technology for the treatment of raw gas derived from the incineration of polymeric materials from WEEE. METHODS: A liquid fuel was chosen in order to minimise technical modifications of the plant. It was analysed for halogens by x-ray fluorescence, for brominated flame retardants by HPLC-UV/MS and for PXDD/F by GC-HRMS. Combustion gases were rapidly cooled down to temperatures below 200 degrees C and emissions of PBDD/F and PCDD/ F were estimated without further off-gas treatment. PBDD/F emissions were computed as PCDD/F toxicity equivalents applying two different calculation approaches. RESULTS AND DISCUSSION: PCDD/F emissions accounted for 0.04 ng I-TEQ/Nm3 and are in compliance with European emission limits. Calculated PBDD/F toxicity equivalents exceeded the emission limit of 0.1 ng I-TEQ/Nm3 by factors of 75 and 208 depending on the calculation approach. A mass balance of PBDD/F and PCDD/F congeners revealed an efficient elimination of more than 95% in most cases. Lower reduction rates (76% for 2,3,7,8-TeBDF and 82% for 1,2,3,7,8-PeBDF) were attributed to incomplete combustion. An intended recovery of halogens by one-stage scrubbing downstream of the pebble heater was ineffective, recovering 28% of the applied chlorine and 9% of the bromine, only. CONCLUSIONS: Our pilot incineration test indicates that the pebble heater technology can effectively suppress a post-combustion synthesis of PCDD/F and PBDD/F, resulting in low PCDD/F emission levels without further off-gas treatment. The presented data state that WEEE is sensible to incomplete combustion, which will lead to increased PBDD/F emissions without increasing PCDD/F emission limits. This finding is especially relevant for small and low-technical incineration appliances, which have been reported to treat WEEE in developing countries and are considered to serve as a significant source of PXDD/F these days. RECOMMENDATIONS AND PERSPECTIVES: Monitoring of PCDD/F emissions only might considerably underestimate the total emission of dioxins and dioxin-like compounds. It is therefore an ineffective means for assessing resulting health risks, at least for those waste treatment plants which are considered to handle the increasing amounts of PBDD/ F-containing polymers from WEEE in future. Consequently, it is recommended to initiate a screening programme for PXDD/F emissions in large scale incineration facilities which are capable of treating WEEE shredder residues.     

PBDF and PBDD from the combustion of bromine containing flame retarded polymers: A survey

The formation of polybrominated dibenzofurans (PBDF) and dibenzodioxins (PBDD) during the pyrolysis of different polymers containing brominated organic flame retardants was investigated. The pyrolyses were conducted at two different temperatures (600°C and 800°C) using three different oven configurations. Both the pyrolysis gases and the solid residues were analysed for PBDF and PBDD.

PBDF were found in almost all samples, but both the concentration and the degree of bromination varied greatly. The largest yields of PBDF in the percent range were measured in the pyrolysis products of polymers containing brominated diphenyl ethers. The other flame retardants generally yielded only a few ppm of PBDF. PBDD are formed only in a few samples and related to the PBDF in very low concentrations.     

Determination of polybrominated diphenyl ethers and PBDD/Fs during the recycling of high impact polystyrene containing decabromodiphenyl ether and antimony oxide

A high impact polystyrene (HIPS) plastic, flame retarded with decabromodiphenyl ether (DecaBDE) and antimony trioxide (Sb2O3) has been repeatedly processed and the amount of debromination of the flame retardant and possible formation of PBDD/F was monitored. No indications of debromination were found. The reprocessed (recycled) plastic was found to comply with the German Chemicals Banning Ordinance. The concentrations of relevant PBDD/F congeners were at least one order of magnitude below the regulated limit values for PBDD/F (1 ppb for the sum of four congeners, 5 ppb for the sum of all eight regulated congeners).     

Characterisation of polymer fractions from waste electrical and electronic equipment (WEEE) and implications for waste management

There is an increasing interest in the end-of-life management of polymers present in waste electrical and electronic equipment (WEEE). This is mainly due to high recycling and recovery quotas set by the European WEEE directive, which can only be fulfilled by including the plastic fraction in recycling and recovery approaches. Previous studies identified a high material diversity and various contaminants in WEEE plastics, including heavy metals, polybrominated biphenyls (PBB), diphenyl ethers (PBDE), as well as polybrominated dibenzodioxins and dibenzofurans (PBDD/F). These substances are regulated by European directives that limit their levels in marketable products. Consequently, both material diversity and contaminants are strong arguments against material recycling and point to hazardous waste treatment. However, recent developments in the production of flame retardants and electrical and electronic goods aimed to reduce contaminants and material diversity. Thus, the present study summarises updated contaminant levels of plastic fractions of European WEEE, as well as data on materials in waste housing polymers. Material characterisation revealed housing fractions to be interesting sources for polymer recycling, which however has to implement potent material separation and/or bromine elimination techniques. With respect to contaminants, our data indicate an effective phase-out of PBB, but still high levels of PBDE and PBDD/F are found. Sources and implications for the material recycling and thermal recovery approaches are discussed in detail.     

Brominated-chlorinated diphenyl ethers formed by thermolysis of polybrominated diphenyl ethers at low temperatures

Polybrominated diphenyl ethers (PBDEs) are a group of brominated flame retardants (BFRs) used mainly as additives in different kinds of plastic material. Various PBDEs are found in all environmental compartments as well as in tissue and blood serum of animals and humans due to their persistence and tendency to bioaccumulate. Emission of PBDEs into the environment can occur during recycling of PBDE-containing plastic material or during their uncontrolled or insufficient combustion as e.g. in accidental fires or landfill fires. Under these circumstances, PBDEs can also function as precursor molecules for the formation of polybrominated dibenzodioxins (PBDDs) and dibenzofurans (PBDFs). In this study, we qualitatively investigated the reaction of two PBDE congeners, 2,2′,4,4′-tetrabromo diphenyl ether (BDE 47) and 2,2′,4,4′,5,5′-hexabromo diphenyl ether (BDE 153), as well as hexabromobenzene (HBB), a flame retardant used in the past, when exposed to temperatures between 250 °C and 500 °C. The formed reaction products were analysed by high resolution gas chromatography–low resolution mass spectrometry (HRGC-LRMS). Among others brominated–chlorinated diphenyl ethers were formed by chlorodebromination of the PBDEs. In addition, thermolysis of BDE 47 and BDE 153 in the presence of tetrachloromethane as model substance for an organic chlorine source was studied. Thermal treatment of HBB resulted in the formation of brominated–chlorinated benzenes.     

Combustion of brominated flame retardants and behavior of its byproducts

The substance flow rate of PBDDs/DFs into flue gas and incineration residues from incineration of three types of waste samples containing brominated flame retardants were examined. The samples used consisted of PBDEs (a typical retardant), used TV casing materials (actual waste materials), and waste printed circuit boards. PBDDs/DFs concentrations in the experimental samples of PBDEs/PE, waste TV casing materials and printed circuit boards ranged between 3000 and 130,000 ng/g. These values are very high when compared to other investigations. The increase of chlorine concentration in input sample reduced the ratio of PBDDs/DFs in flue gas and raised the ratio of PCDDs/DFs. With adequate combustion control and flue gas treatment, the amount of PBDDs/DFs released from the incineration of resin containing brominated flame retardants was lower than the input amount. The presence of PBDDs/DFs in incineration residues dominated the total amount of dioxins released. When PBDDs/DFs, PCDDs/DFs and PXDDs/DFs were considered as a total, the total amount released was lower than the total amount input.     

Distribution of polybrominated diphenyl ethers (PBDEs) and polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) in municipal solid waste incinerators

The stack flue gases and the ashes in different units of two municipal solid waste incinerators (MSWIs) are sampled to investigate the characteristics of polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs), and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Bottom ashes (BA) exhibited much higher PBDD/F (8.11-52.2 pg TEQ/g) and PBDE contents (20.4-186 ng/g) than those of fly ashes (0.0932-2.02 pg TEQ/g and 0.332-25.5 ng/g), revealing that the PBDD/Fs and PBDEs in the feeding waste may not be completely destroyed. The PBDE concentrations/contents in the stack flue gases (26.1-109 ng/Nm³) and in the BA (20.4-186 ng/g) of the MSWIs could reach three orders higher than those in the atmosphere and reference soils. PBDE contributions to the environment from the stack flue gases or the reutilization of BA of MSWIs should not be ignored from the developing PBDE inventory.     

Polybrominated, polychlorinated and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans and dioxin-like polychlorinated biphenyls in marine surface sediments from Hong Kong and Korea

In this study we investigated occurrences and distribution patterns of dioxin-related compounds (DRCs) such as polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs), polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) in marine surface sediments collected from the coastal waters of Hong Kong and Korea. In most sampling sites, concentrations of PCDDs were the highest, followed by DL-PCBs, PCDFs, PBDFs, PBDDs, MoBPCDDs and MoBPCDFs in this order. Levels of PBDD/Fs were generally 1-2 orders of magnitude lower than chlorinated analogues. Levels of PCDDs are higher than PCDFs in Hong Kong while levels of PBDFs are higher than PBDDs in Korea (p < 0.05). Report of PBDD/Fs and MoBPCDD/Fs in sediments from East Asian countries is novel and original. Environmental levels of PBDD/Fs are supposed to start increasing in accordance with rising production, use and disposal of brominated flame retardants (BFRs) and recycling processes of e-waste in Asian developing countries.     

Emissions of organophosphate and brominated flame retardants from selected consumer products and building materials

The emissions of selected flame retardants were measured in 1- and 0.02-m³ emission test chambers and 0.001-m³ emission test cells. Four product groups were of interest: insulating materials, assembly foam, upholstery/mattresses, and electronics equipment. The experiments were performed under constant environmental conditions (23°C, 50% RH) using a fixed sample surface area and controlled air flow rates. Tris (2-chloro-isopropyl)phosphate (TCPP) was observed to be one of the most commonly emitted organophosphate flame retardants in polyurethane foam applications. Depending on the sample type, area-specific emission rates (SER_a) of TCPP varied between 20 ng m⁻² h⁻¹ and 140 μg m⁻² h⁻¹.The emissions from electronic devices were measured at 60°C to simulate operating conditions. Under these conditions, unit specific emission rates (SER_u) of organophosphates were determined to be 10–85 ng unit⁻¹ h⁻¹. Increasing the temperature increased the emission of several flame retardants by up to a factor of 500. The results presented in this paper indicate that emissions of several brominated and organophosphate flame retardants are measurable. Polybrominated diphenylethers exhibited an SER_a of between 0.2 and 6.6 ng m⁻² h⁻¹ and an SER_u of between 0.6 and 14.2 ng unit⁻¹ h⁻¹. Because of sink effects, i.e., sorption to chamber components, the emission test chambers and cells used in this study have limited utility for substances low vapour pressures, especially the highly brominated compounds; hexabromocyclododecane had an SER_a of between 0.1 and 29 ng m⁻² h⁻¹ and decabromodiphenylether was not detectable at all.     

Hazardous substances in indoor dust emitted from waste TV recycling facility

Various hazardous substances contained in waste TV sets might be released into environment via dust during recycling activities. Two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and tetrabromobisphenol A (TBBPA), and five kinds of heavy metals (Cu, Pb, Cd, Cr, and Ni) were detected in indoor dust collected from two workshops (TV dismantling workshop and subsequent recycling workshop). PBDEs concentrations in dust from waste wires recycling line (722,000 ng/g) were the highest among the studied sites, followed by those in manual dismantling–sorting line (117,000 ng/g), whereas TBBPA concentrations were the highest in manual dismantling–sorting line (557 ng/g) and printed circuit board (PCB) recycling line (428 ng/g). For heavy metals, Cu and Pb were the most enriched metals in all dust samples. The highest concentration of Pb (22,900 mg/kg) was found in TV dismantling workshop-floor dust. Meanwhile, Cu was the predominant metal in dust from the PCB recycling line, especially in dust collected from electrostatic separation area (42,700 mg/kg). Occupational exposure assessment results showed that workers were the most exposed to BDE-209 among the four PBDE congeners (BDE-47, BDE-99, BDE-153, and BDE-209) in both workshops. The hazard quotient (HQ) indicated that noncancerous effects were unlikely for both BFRs and heavy metals (HQ?<?1), and carcinogenic risks for Cd, Cr, and Ni (risk?<?10^?6) on workers in two workshops were relatively low.     

Distribution and levels of brominated flame retardants in sewage sludge

One hundred and sixteen sewage sludge samples from 22 municipal wastewater treatment plants in Sweden were analysed for brominated flame retardants. Polybrominated diphenyl ethers (PBDEs) were in the range n.d.-450 ng/g wet weight, tetrabromobisphenol A (TBBPA) varied between n.d. and 220 ng/g wet weight, 2,4,6-tribromophenol was in the range n.d.-0.9 ng/g wet weight and polybrominated biphenyls were not detected (except for a possible analytical interference). There was a significant variation in the samples among plants. Influence from industries and other local sources can therefore be assumed. The correlation pattern indicated contribution from three different types of technical products; composed of either low-brominated PBDEs, decaBDE or TBBPA.     

Transfer of brominated flame retardants from components into dust inside television cabinets

Television (TV) set components are highly flame resistant, with their added brominated compounds such as polybrominated diphenyl ethers (PBDEs). These compounds might be released indoors via dust, which presents a potential exposure pathway for humans in the home environment. In this study, we collected dust from inside TV sets and TV set component samples (parts of housing front cabinets, rear cabinets and circuit boards) of five sets used in Japan. We measured BFRs (i.e., PBDEs, tetrabromobisphenol A (TBBPA) and hexabromocyclododecanes (HBCDs)) and polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/DFs). Analytical results of the TV components showed that the concentrations of PBDEs, TBBPA and PBDFs (48,000mug/g, 19,000mug/g and 9600ng/g as mean values, respectively) were all highest in the rear cabinets. The SigmaPBDD concentrations (460ng/g as a mean value) detected were highest in the circuit board samples. The respective SigmaPBDE and SigmaPBDF concentrations in the dust samples were 67-500mug/g (mean 300mug/g) and 180-650ng/g (mean 410ng/g). Such concentrations were 2-3 orders of magnitude higher than those previously reported for house dust samples, which suggests that the brominated compounds are transferred from TV components into dust. Comparison of congener patterns of the brominated compounds in the dust identified the components as the source of these BFRs.     

Modified clean-up for PBDD,PBDF and PBDE with an active carbon column--its application to sediments

A clean-up method for polybrominated dibenzo-p-dioxins (PBDDs), dibenzofurans (PBDFs) and diphenyl ethers (PBDEs) was modified using combinations of multi-layered silica gel, Florisil and active carbon columns. By using active carbon column chromatography in the final procedure, PBDEs were well separated from PBDD/Fs in an elution test with reference standards. We report the application of this method to sediment samples taken from industrialized areas in Japan. These sediments contained PBDEs ranging in concentration from 13 to 2394 pg/g, dry wt. PBDEs did not interfere with the quantification of PBDD/Fs. In addition, PBDEs found in the PBDD/F fraction did not interfere with the identification of PBDFs using the HRGC/HRMS separation method. Some 2,3,7,8-tetra- to hexabrominated dioxins and furans were also detected in the sediment samples.     

Brominated flame retardants and perfluorinated chemicals, two groups of persistent contaminants in Belgian human blood and milk

We assessed the exposure of the Flemish population to brominated flame retardants (BFRs) and perfluorinated compounds (PFCs) by analysis of pooled cord blood, adolescent and adult serum, and human milk. Levels of polybrominated diphenyl ethers (PBDEs) in blood (range 1.6-6.5 ng/g lipid weight, lw) and milk (range 2.0-6.4 ng/g lw) agreed with European data. Hexabromocyclododecane ranged between <2.1-5.7 ng/g lw in milk. Perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) dominated in blood and ranged between 1 and 171 ng/mL and <0.9-9.5 ng/mL, respectively. Total PFC levels in milk ranged between <0.5-29 ng/mL. A significant increase in PBDE concentrations was detected from newborns (median 2.1) to the adolescents and adults (medians 3.8 and 4.6 ng/g lw, respectively). An identical trend was observed for PFOS, but not for PFOA. We estimated that newborn exposure to BFRs and PFCs occurs predominantly post-natally, whereas placental transfer has a minor impact on the body burden.     

Analytical protocol for the analysis of polybrominated dibenzo-dioxins and dibenzofurans: Data quality objectives and single-laboratory evaluation

An analytical protocol for the measurement of part per billion and sub-part per billion levels of PBDDs and PBDFs in selected flame retardant chemicals (polybrominated diphenyloxides; PBDPO) was developed. The fractionation/enrichment procedures were optimized to minimize the effects of the PBDPOs upon the ability to recover and measure the PBDD/PBDFs. Results from the method validation show that the current methodology is capable of accuracies ranging from 70% to 150% at the 0.1 to 10 ppb levels while larger sample sizes (from 20–200 mg to 4 g) are necessary in order to meet the EPA target Test Rule limit of quantification (LOQ) requirements.     

Chlorohydrocarbons, PCB congeners, polychlorodioxins, furans and dibenzothiophenes in pine needles in the vicinity of a metal reclamation plant

Chlorohydrocarbons, PCB congeners, polychlorodioxins, furans and dibenzothiophenes in pine needles in the vicinity of a metal reclamation plant were analyzed by GC/ECD and GC/MS. Wax and the rest of the needles were analyzed separately. As a rule the concentrations of -HCH (0.5–13.6 ng/g), γ-HCH (0.4–7.3 ng/g), HCB (0.2–3.4 ng/g), PCB congeners (0.2–67 ng/g), PCDDs and PCDFs were higher in the older needles. The ratio of the concentration in the wax to the concentration in the rest of the needles was higher in the younger needles. The concentrations of PCB congeners, TeCDDs and TeCDFs were higher in the needles collected in the area nearest to the plant. The samples, obviously, contained tri- and tetrachlorodibenzothiophenes but these were not determined quantitatively due to interfering peaks in GC/MS.     

Pollution survey of polycyclic aromatic hydrocarbons in surface water of Hangzhou, China

The concentrations of 10 polycyclic aromatic hydrocarbons (PAHs) were simultaneously measured for five times (July and November 1999–2002) in four water bodies of Hangzhou, China. To investigate possible sources of PAH contamination, sediments, soils, runoff water and atmospheric particles of the region were also analyzed for their PAH contents. The maximum levels of PAHs in the water bodies (34.4–67.7 μg/l) were found in July, while significantly lower PAH concentrations (4.7–15.3 μg/l) were measured in November. The contamination is substantial and it may have resulted in acute toxic effects on aquatic organisms. The measured PAH concentrations in sediments and soils (224–4222 ng/g), runoff water (8.3 μg/l) and air particles (2.3 μg/m³) are discussed in relation to concentrations and patterns found in the surface water bodies. Comparison of PAH levels in sediments and soils led to the conclusion that the erosion of soil material does not contribute significantly to the contamination of sediments. The atmospheric PAH deposition to water bodies in the city area of Hangzhou was estimated to be 530 tons/a, while the contribution of surface runoff water was estimated to be 30.7 tons/a. The ratios of selected PAH were then used to illuminate the possible origin of PAHs in the examined samples (petrogenic, pyrogenic).     

Organophosphorus flame retardants in house dust from the Philippines: occurrence and assessment of human exposure

The use of organophosphorus flame retardants (PFRs) as flame retardants and plasticizers has increased due to the ban on common polybrominated diphenyl ether mixtures. However, only limited information on PFR contamination is available so far from Southeast Asia. In the present study, residual levels of PFRs in house dust and exposure through dust ingestion were investigated in the Philippines. House dust samples (n?=?37) were collected from Malate (residential area) and Payatas (municipal dumping area) in the Philippines and analyzed using ultra-high-performance liquid chromatography coupled with tandem mass spectrometry. Among the targeted seven PFRs, triphenyl phosphate (TPP) was the predominant compound. Median levels of ΣPFRs in Malate (530 ng/g) were two times higher (p?<?0.05) than in Payatas (240 ng/g). The estimated daily intake of PFRs in the Philippines (of areas studied) via house dust ingestion was below the guideline values. House dust may be an important contributor in the overall exposure of humans to TPP even when considering dietary sources. To our knowledge, this is a first report on PFR contamination in house dust from developing country. PFRs were ubiquitously detected in the home environments in the Philippines. Although estimated exposure levels through dust ingestion were below the guideline, it was suggested that toddlers are at higher risk. Therefore, further investigations to understand the behavior of PFRs in house and other microenvironments and overall exposure pathways for the country’s populace to PFRs are necessary.     

Organic chlorine compounds in lake sediments. IV. Dioxins, furans and related chloroaromatic compounds

Polychlorodibenzo-p-dioxins (PCDDs), polychlorodibenzofurans (PCDFs), polychloronaphthalenes (PCNs) and coplanar PCBs were measured in surface sediments from 18 lake areas in Central Finland. Toxic 2, 3, 7, 8-substituted PCDD and PCDF congeners occurred at low levels (<20 − 230 pg/g dw). PCNs appeared at few ng/g (total PCNs) levels. Pulp mills or any other local sources could not be associated with the sedimented PCDDs, PCDFs and PCNs. Coplanar PCB congeners 77 and 105 (IUPAC Nr) were generally found at 20–550 pg/g levels. The most toxic congener 126 was measured (110 pg/g) only at one area near a local PCB leakage. Pulp mill originated aromatic chlorocompounds which coelute with PCDDs and PCDFs in clean up, probably alkyl polychlorobibenzyls (R-PCBBs) appeared at ng/g levels and showed a clear gradient dowstreams from pulp mill effluent points.