Actinides and decay products in selected produce and bioindicators in the vicinity of a uranium plant

Cypress needles collected at the edge of the Malvési uranium facility (SW France) exhibit enhanced activities of actinides and some decay products (uranium, americium, plutonium, (230)Th, (226)Ra) compared to a remote site. These enhanced activities resulted from the release of U via smokestacks and passive release from former artificial ponds located inside the nuclear site. Enhanced activities are also observed in selected produce (wheat, lettuce, fruits) sampled from the edge of the site. However, excess actinides measured in wheat grains in 2007 are inconsistent with the activities and the uranium ratio measured in the soils. This result suggests that the studied annual crops were contaminated mainly through the short-term release of airborne actinides, and that other transfer pathways, such as, uptake through the roots or adhesion of soil particles, were negligible.     

Assessment of particulate matter in the urban atmosphere: size distribution, metal composition and source characterization using principal component analysis

In this study, the size distribution of airborne particles and related heavy metals Co, Cd, Sn, Cu, Ni, Cr, Pb and V in two urban areas in Istanbul: Yenibosna and Goztepe, were examined. The different inhalable particles were collected by using a cascade impactor in eight size fractions (<0.4 μm, 0.4-0.7 μm, 1.1-2.1 μm, 2.1-3.3 μm, 3.3-4.7 μm, 4.7-5.8 μm, 5.8-9 μm and >9 μm) for six months at each station. Samples were collected on glass fiber filters and filters were extracted and analyzed using ICP-MS. Log-normal distributions showed that the particles collected at the Yenibosna site have a smaller size compared to the Goztepe samples and the size distribution of PM was represented the best by the tri-modal. The average total particle concentrations and standard deviations were obtained as 67.7 ± 17.0 μg m(-3) and 82.1 ± 21.2 μg m(-3), at the Yenibosna and G?ztepe sites, respectively. The higher metal rate in fine and medium coarse PM showed that the anthropogenic sources were the most significant pollutant source. Principal component analysis identified five components for PM namely traffic, road dust, coal and fuel oil combustion, and industrial.     

Characterisation of individual aerosol particles on moss surfaces: implications for source apportionment

The size, morphology and chemical composition of 8405 particles on moss surfaces (Hylocomium splendens) was investigated by scanning electron microscopy and energy-dispersive X-ray microanalysis. Two moss samples from three locations in Southern Norway (Alg?rd, Birkeland, Neslandsvatn) and two sampling years (1977 and 2005) each were selected leading to a total of 12 samples investigated. At all three locations, particle deposition decreased substantially with time. The major particle groups encountered include silicates, iron-rich silicates, metal oxides/hydroxides, iron oxides/hydroxides, carbonates, carbon-rich particles, silicate fly ashes, iron-rich silicate fly ashes, and iron oxide fly ashes. Between 1977 and 2005, the relative number abundance of the three fly ash groups decreased substantially from approximately 30-60% to 10-18% for the small particles (equivalent projected area diameter <1 microm), and from 10-35% to 2-9% for large particles with diameters ≥1 microm. This decrease of fly ash particles with time was overlooked in previous papers on atmospheric input of pollutants into ecosystems in Southern Norway. In general, the presence of fly ash particles is ignored in most source apportionment studies based on bulk chemical analysis. Consequently, the geogenic component (crustal component) derived from principal component analysis is overestimated systematically, as it has a similar chemical composition as the fly ash particles. The high abundance of fly ashes demonstrates the need to complement source apportionment based on bulk chemistry by scanning electron microscopy in order to avoid misclassification of this important anthropogenic aerosol component.     

Processing and analysis of roadway runoff micro (< 20 μm) particles

This study was performed to compare paper and sieving filtration methods for processing micro particles (< 20 μm) in roadway runoff for water quality evaluation. The consequence of a lack of reliable particle processing on particle number, particle concentration and particulate elemental composition, as well as their influence on particle mass and pollutant load calculations, is discussed. Results show that the paper filtering method can affect the measurement of particle size distributions of highway runoff samples. Contrary to common practice, it is not always correct to assume that the number and concentration of particles < 38 μm is the same as the number and concentration of particles < 20 μm. Processed samples for micro particles were most similar to unprocessed samples when nylon sieves were used. Samples filtered by paper deviated significantly from unprocessed samples. These deviations can cause inaccuracies up to 90 percent, in particle count and concentration, TSS calculations, elemental mass composition, and particle and elemental mass loading.     

Differences in metal concentration by particle size in house dust and soil

The majority of particles that adhere to hands are <63 μm in diameter yet risk assessments for soil remediation are typically based on soil samples sieved to <250 μm. The objective of our study was to determine if there is a significant difference in metal concentration by particle size in both house dust and soil. We obtained indoor dust and yard soil samples from 10 houses in Tucson, Arizona. All samples were sieved to <63 μm and 63 to <150 μm and analyzed for 30 elements via ICP-MS following nitric acid digestion. We conducted t-tests of the log-transformed data to assess for significant differences that were adjusted with a Bonferroni correction to account for multiple comparisons. In house dust, significant differences in concentration were observed for Be, Al, and Mo between particles sizes, with a higher concentration observed in the smaller particle sizes. Significant differences were also determined for Mg, Ca, Cr, Co, Cu, Ge, Zr, Ag, Ba, and Pb concentration in yard soil samples, with the higher concentration observed in the smaller particles size for each element. The results of this exploratory study indicate that current risk assessment practices for soil remediation may under estimate non-dietary ingestion exposure. This is of particular concern for young children who are more vulnerable to this exposure route due to their high hand mouthing frequencies. Additional studies with a greater number of samples and wider geographic distribution with different climates and soil types should be completed to determine the most relevant sampling practices for risk assessment.     

Mass loading of nickel and uranium on plant surfaces: application of laser ablation-ICP-MS

Transport of contaminated sediments from a former radiological settling pond results in the deposition of U and Ni in the Lower Tims Branch (LTB)(Aiken, SC, USA). Uranium is unavailable for plant uptake, but elevated U and Ni concentrations associated with foliage of understory plants suggested mass loading. Mass loading of contaminated soil on Andropogon elliottii Chapman (Poaceae) was investigated using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The technique allows for rapid quantitative elemental depth profiling. Fresh washed and unwashed leaves (n= 5) from the contaminated area were compared with those from an uncontaminated area, analysing Ni and U at ten randomly chosen points on each leaf. Nickel and U concentrations differed significantly between washed and unwashed leaves from LTB. Particles on unwashed leaves measured up to 300 [micro sign]m in diameter, and were enriched with U. Uranium was detected on the surface of the leaf, whereas Ni was detected within leaf tissues. In unwashed LTB leaves, Ni and U concentrations did not significantly differ in areas with and without visible particles, suggesting that there were much smaller particles, indistinguishable at [times]100 magnification, which contributed to the overall metal burden. Washing removed the majority of the Ni and U on the surface, but residual U and Ni was detected. Irregularities in the leaf surface, such as scars from herbivory contained elevated U concentrations despite a washing step, presumably from trapping soil particles. Laser ablation ICP-MS revealed that mass loading makes a significant contribution to the contaminant burden of understory plants at LTB.     

Documentation of bioaerosol concentrations in an indoor composting facility in France

Bioaerosol concentrations were investigated in a totally indoor composting facility processing fermentable household and green wastes to assess their variability. Stationary samples were collected by filtration close to specific composting operations and then were analysed for cultivable mesophilic bacteria, thermophilic bacteria, mesophilic fungi, thermophilic fungi, endotoxins and total airborne bacteria (DAPI-staining). Indoor concentrations exceeded the background levels, between 500 and 5400 EU m(-3) for endotoxins, 10(4) and 10(6) CFU m(-3) for cultivable bacteria and generally below 10(5) CFU m(-3) for airborne cultivable fungi. No significant (p > 0.05) differences were observed between the indoor composting operations. Successive 30 minute bioaerosol samples were collected to investigate the variation of cultivable mesophilic microorganisms over the work shift. Concentrations of mesophilic bacteria and fungi varied up to 1 log unit depending on the time at which they were collected in the day. Total airborne particles, counted using an optical particle counter, were present at up to 10(8) particles m(-3) and several concentration peaks were noted. Values for total airborne bacteria were roughly 70-fold higher than cultivable bacteria. These results raise the question of the sampling strategy (duration of sampling; number of samples to be collected) used in similar studies. They provide new bioaerosol concentration data in a composting facility and suggest that the filtration sampling method might be a useful tool for exposure measurements in that occupational environment.     

Characterization of individual aerosol particles in workroom air of aluminium smelter potrooms

Aerosol particles with aerodynamic diameters between 0.18 and 10 microm were collected in the workroom air of two aluminium smelter potrooms with different production processes (Soderberg and Prebake processes). Size, morphology and chemical composition of more than 2000 individual particles were determined by high resolution scanning electron microscopy and energy-dispersive X-ray microanalysis. Based on chemical composition and morphology, particles were classified into different groups. Particle groups with a relative abundance above 1%(by number) include aluminium oxides, cryolite, aluminium oxides-cryolite mixtures, soot, silicates and sea salt. In both production halls, mixtures of aluminium oxides and cryolite are the dominant particle group. Many particles have fluoride-containing surface coatings or show agglomerations of nanometer-sized fluoride-containing particles on their surface. The phase composition of approximately 100 particles was studied by transmission electron microscopy. According to selected area electron diffraction, sodium beta-alumina (NaAl(11)O(17)) is the dominant aluminium oxide and cryolite (Na(3)AlF(6)) the only sodium aluminium fluoride present. Implications of our findings for assessment of adverse health effects are discussed.     

乌鲁木齐市可吸入颗粒物污染水平及其与气象因素的相关性分析

为了解可吸入颗粒物污染水平与气象因素之间的关系,从2008年9月—2010年2月采集乌鲁木齐市可吸入颗粒物样品,并对其随时间的变化特征及其与气象因素之间的相关性进行了统计分析。结果表明,采样时间内可吸入颗粒物中PM2.5和PM2.5-10的质量浓度的范围分别为38.2~468.7μg/m3和20.8~243.1μg/m3,平均浓度分别为134.2μg/m3和69.2μg/m3。可吸入颗粒物同时受几种气象因素的影响,其浓度与温度、能见度、风速呈负相关,与湿度呈正相关。     

Monitoring Of Vehicles Derived Particulates Using Magnetic Properties Of Leaves

Biomonitoring of vehicle-derived particulates is conducted by taking magnetic measurements of roadside tree leaves. Remanent magnetization (IRM_{300 mT}) of more than 400 Delbergia sissoo leaves was determined and IRM_{300 mT} normalized for the leaf area. The normalized 2-D magnetization as shown by results is dominantly controlled by the tree's distance to the road. The spatial and temporal variations of vehicle-derived particulates were mapped using magnetic analysis. 2D-magnetizations values were higher for leaves collected adjacent to major road sections than for those from village road suggesting vehicle emissions, rather than resuspended road dust, as the major cause of magnetic particles of roadside tree leaves. Vehicles derived particulates are responsible for tree leaf magnetism, and the leaf magnetizations values fall significantly from high values proximal to the roadside to lower values at the distal side. This suggests the ability of trees to reduce particulates concentrations in the atmosphere. The rainfall produces a net decrease in the leaf magnetic dust loadings.     

Chemical composition of individual aerosol particles in workplace air during production of manganese alloys

Aerosol particle samples were collected at ELKEM ASA ferromanganese (FeMn) and silicomanganese (SiMn) smelters at Porsgrunn, Norway, during different production steps: raw material mixing, welding of protective steel casings, tapping of FeMn and slag, crane operation moving the ladles with molten metal, operation of the Metal Oxygen Refinement (MOR) reactor and casting of SiMn. Aerosol fractions were assessed for the analysis of the bulk elemental composition as well as for individual particle analysis. The bulk elemental composition was determined by inductively coupled plasma atomic emission spectrometry. For individual particle analysis, an electron microprobe was used in combination with wavelength-dispersive techniques. Most particles show a complex composition and cannot be attributed to a single phase. Therefore, the particles were divided into six groups according to their chemical composition: Group I, particles containing mainly metallic Fe and/or Mn; Group II, slag particles containing mainly Fe and/or Mn oxides; Group III, slag particles consisting predominantly of oxidized flux components such as Si, Al, Mg, Ca, Na and K; Group IV, particles consisting mainly of carbon; Group V, mixtures of particles from Groups II, III and IV; Group VI, mixtures of particles from Groups II and III. In raw material mixing, particles originating from the Mn ores were mostly found. In the welding of steel casings, most particles were assigned to Group II, Mn and Fe oxides. During the tapping of slag and metal, mostly slag particles from Group III were found (oxides of the flux components). During movement of the ladles, most particles came from Group II. At the MOR reactor, most of the particles belonged to the slag phase consisting of the flux components (Group III). The particles collected during the casting of SiMn were mainly attributed to the slag phase (Groups III and V). Due to the compositional complexity of the particles, toxicological investigations on the kinetics of pure compounds may not be easily associated with the results of this study.     

一次连续在线观测分析天津市细颗粒物污染特征

根据2005年的5月17日—5月23日GR IMM(1.109#)谱分析仪在线观测结果考察天津市细颗粒物浓度和质量浓度特征。观测期间,天津市颗粒物数浓度平均值为1 124 cm-3,粒径分布为0.25μm~0.60μm,98.5%粒子的粒径0.65μm。同期PM10日均质量浓度值为204μg/m3,ρ(PM2.5)为104μg/m3,ρ(PM1.0)为82.9μg/m3。ρ(PM1.0)/ρ(PM2.5)超过80%,粒径1μm超细颗粒物为天津城市大气颗粒物的主要成分。     

Characterization of mineral particles in winter fog of Beijing analyzed by TEM and SEM

Aerosol samples were collected during winter fog and nonfog episodes in Beijing. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were applied to study morphologies, sizes, and compositions of aerosol particles. TEM observation indicates that most mineral particles collected in fog episode are scavenged in fog droplets. Number–size distributions of mineral particles collected in fog and nonfog episodes show two main peaks at the ranges of 0.1–0.3 and 1–2.5 μm, respectively. Based on their major compositions, mineral particles mainly include Si-rich, Ca-rich, and S-rich. Average S/Ca ratio of mineral particles collected in fog episode is 6.11, being eight times higher than that in nonfog episodes. Development mechanism of individual mineral particles in fog droplets is proposed. It is suggested that mineral particles with abundant alkaline components (e.g., “Ca-rich” particles) occurred in air should alleviate acidic degree of fog and contribute to complexity of fog droplets in Beijing.     

Ion chemistry and individual particle analysis of atmospheric aerosols over Mt. Bogda of eastern Tianshan Mountains, Central Asia

Aerosol samples were collected during the scientific expedition to Mt. Bogda in July-August, 2009. The major inorganic ions (Na(?+?), NH??, K(?+?), Mg(2?+?), Ca(2?+?), Cl(?-?), SO2??, and NO??) of the aerosols were determined by ion chromatography. SO2??, NO??, and Ca(2?+?) were the dominate ions, with the mean concentrations of 0.86, 0.56, and 0.28 μg m?3, respectively. These mean ion concentrations were generally comparable with the background conditions in remote site of Xinjiang, while much lower than those in ürümqi. Morphology and elemental compositions of 1,500 particles were determined by field emission scanning electron microscopy equipped with an energy dispersive X-ray spectrometer. Based on the morphology and elemental compositions, particles were classed into four major groups: soot (15.1%), fly ash (4.7%), mineral particles (78.9%), and little other matters (0.8% Fe-rich particles and 0.5% unrecognized particles). Presence of soot and fly ash particles indicated the influence of anthropogenic pollutions, while abundance mineral particles suggested that natural processes were the primary source of aerosols over this region, coinciding with the ionic analysis. Backward air mass trajectory analysis suggested that ürümqi may contribute some anthropogenic pollution to this region, while the arid and semi-arid regions of Central Asia were the primary source.     

Biomonitoring of antimony in environmental matrices from terrestrial and limnic ecosystems

Elder and poplar leaves from various sampling sites were studied with respect to their antimony content. Moreover, a retrospective determination of Sb was performed in representative limnic and terrestrial samples of the Federal Environmental Specimen Bank of Germany which have been collected over 14 years. The analytical procedure is based on an open vessel acid digestion of freeze-dried biological samples and the subsequent quantification of Sb in the digests by flow injection hydride generation atomic absorption spectrometry. Strict quality control schemes were applied to the entire procedure to guarantee accurate and precise results. No long-term changes of the Sb concentrations were found in spruce shoots or poplar leaves from different sampling sites. However, spruce shoots from a semi-natural region showed concentrations of Sb (approximately 22 ng g-1; range: 17-29 ng g-1) that were approximately four times lower than in corresponding samples from an urban-industrialized area. The analysis of virgin and washed elder leaves revealed that approximately 20-30% of the Sb is present on the leaf surface. Sb levels in elder leaves ranged from 5.2 +/- 0.3 ng g-1 in samples from Argentina to 589 +/- 30 ng g-1 in leaves collected directly beside a motorway in Germany. Similarly, poplar leaves from Argentina and Chile showed about 4 ng Sb g-1, whereas 150 ng Sb g-1 was found in poplar leaves from Germany. The lowest concentrations of Sb were determined in digests of pigeon eggs (approximately 2 ng g-1), bream liver (approximately 4 ng g-1) and deer liver (approximately 6 ng g-1). A similar pattern of Sb concentrations in spruce shoots, leaves or liver samples from an industrialized area and an agrarian ecosystem in Germany was established. Concentrations of Sb in elder leaves were closely associated with car traffic, giving maximum concentrations of 589 ng g-1 directly beside a motorway, 207 ng g-1 50 m from the motorway and 153 ng g-1 in a close residential area.     

Heavy metal concentrations in particle size fractions from street dust of Murcia (Spain) as the basis for risk assessment

Street dust has been sampled from six different types of land use of the city of Murcia (Spain). The samples were fractionated into eleven particle size fractions (<2, 2-10, 10-20, 20-50, 50-75, 75-106, 106-150, 150-180, 180-425, 425-850 μm and 850-2000 μm) and analyzed for Pb, Cu, Zn and Cd. The concentrations of these four potentially toxic metals were assessed, as well as the effect of particle size on their distribution. A severe enrichment of all metals was observed for all land-uses (industrial, suburban, urban and highways), with the concentration of all metals affected by the type of land-use. Coarse and fine particles in all cases showed concentrations of metals higher than those found in undisturbed areas. However, the results indicated a preferential partitioning of metals in fine particle size fractions in all cases, following a logarithmic distribution. The accumulation in the fine fractions was higher when the metals had an anthropogenic origin. The strong overrepresentation of metals in particles <10 μm indicates that if the finest fractions are removed by a vacuum-assisted dry sweeper or a regenerative-air sweeper the risk of metal dispersion and its consequent risk for humans will be highly reduced. Therefore, we recommend that risk assessment programs include monitoring of metal concentrations in dust where each land-use is separately evaluated. The finest particle fractions should be examined explicitly in order to apply the most efficient measures for reducing the risk of inhalation and ingestion of dust for humans and risk for the environment.     

Chemical composition, sources, solubility, and transport of aerosol trace elements in a tropical region

Aerosol particle samples (PM10) were collected at urban, industrial and rural sites located in Rio de Janeiro, Brazil, between October 2008 and September 2009. Aerosol samples for each site were analyzed for total and soluble metals, water-soluble ions, carboxylic acids, and water-soluble organic carbon (WSOC). The results showed that the mean PM10 concentrations were 34 μg m(-3); 47 μg m(-3) and 71 μg m(-3) at the rural, urban and industrial sites, respectively. An increase in the average concentration of these particles due to air stagnation was observed during the period from May to September for all sites, and an increase in hospitalization for respiratory problems was also reported. On average, the anions species represented 4 to 14% of total content, while cations species corresponded to 1 to 11% and 7.5% for WSOC. The overall metal content at the industrial site was nearly the double that at the rural site. The concentrations of the studied species are influenced mainly by site location and the specific characteristics present at each site. However, higher concentrations of some species were observed on particular dates and were probably due to biomass burning and African dust events. The acid/aqueous percentiles showed that the most efficiently extracted metals from the aqueous phase were V and Ni (40%), while Al and Fe represented a lower percentage (<3%). Analysis of the aqueous fraction provides important information about the bioavailability of metals that is associated with the inflammatory process in the lungs.     

Chemical composition of individual aerosol particles from working areas in a nickel refinery

Individual aerosol particles (n = 1170) collected at work stations in a nickel refinery were analyzed by wavelength-dispersive electron-probe microanalysis. By placing arbitrary restrictions on the contents of sulfur and silicon, the particles could be divided into four main groups. Scanning electron images indicated that most of the particles examined were relatively small (< or = 2 microm, equivalent projected area diameter), and that their morphology suggested formation from a melt. There was an absence of well-defined phases and simple stoichiometries, indicating that exposures to pure substances such as nickel subsulfide or specific oxides appeared not to occur. Although the elemental composition of particles varied greatly, a rough association was evident with the known elemental content of the refinery intermediates. The implications of the findings for aerosol speciation measurements, toxicological studies and interpretation of adverse health effects are explored.     

Personal air sampling and analysis of polybrominated diphenyl ethers and other bromine containing compounds at an electronic recycling facility in Sweden

Brominated flame retardants (BFRs) have been used extensively and are considered ubiquitous contaminants. To evaluate exposure to brominated flame retardants within an electronic recycling facility personal air monitoring was done during a two year period. A total of 22 polybrominated diphenyl ethers (PBDEs) and 2 other bromine containing organic compounds have been analysed and evaluated in 17 personal air samples. The most abundant congeners of PBDE was #209 (<0.7-61 ng m(-3)), #183 (<0.1-32 ng m(-3)) indicating the use of the commercial octaBDE mixture, followed by PBDE #99 and #47 (<1.3-25 and <0.9-16 ng m(-3), respectively). The second most abundant peak in the chromatogram from all samples was identified as 1,2-bis(2,4,6-tribromophenyxy)ethane (BTBPE) in the concentration range <0.6-39 ng m(-3) (semi-quantitatively calculated against PBDE #191). A second bromine containing compound was also detected, structurally similar to decabromodiphenyl ethane (DeBDethane), however no definite identification could be made. The air samples were also evaluated on a work exposure category basis. The workers represented three different categories: dismantlers, other workers and unexposed. There was a significant difference (p < 0.05 with the Mann-Whitney test) among the dismantlers and the unexposed categories for PBDE congeners #47, #100, #99, #154; #153, #183, #209 and BTBPE. Another observation was that the air concentrations of PBDEs and BTBPE in the breathing zone were negatively correlated (p < 0.05) to the amount of recycled material (in kg). The present work shows that the exposure to brominated flame retardants varied within the electronic facility and that further research is needed to evaluate how the exposure differs with different products being dismantled as well as how the bioavailability of the different BFRs to humans is related to particle exposure.     

Effects of silicon on copper toxicity in Erica andevalensis Cabezudo and Rivera: a potential species to remediate contaminated soils

The influence of silicon on responses to copper excess was studied in plants of Erica andevalensis. Plantlets were grown in nutrient solutions containing two Cu (1 and 500 μM) and three Si concentrations (0, 0.5 and 1 mM). Plant growth, water content, and mineral nutrient concentration were determined. Plants grown with 500 μM Cu showed differences in growth and shoot water content depending on Si supply. The addition of 1 mM Si in high-Cu nutrient solutions significantly improved plant growth and reduced water loss preventing plant death related to Cu-excess. Silicon supply reduced significantly leaf Cu concentration (up to 32%) and increased Cu concentration in roots. Phytoliths isolated from leaves were analysed by scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. Such phytoliths consisted in silica deposits associated with Cu and other elements (K, Ca, P). Improvement by Si of Cu tolerance in E. andevalensis was clearly related to the inhibition of Cu upward transport. The leaf phytoliths formed in Si-treated plants might have some contribution to tolerance by Cu immobilisation and inactivation.