Effects of volatile organic compounds on clay landfill liner performance

Clay borrow materials intended for use in a clay liner system were found to be contaminated by low concentrations of volatile organic chemicals (VOCs). The suspected source of contaminants was a nearby Superfund site where similar compounds were found in soil and groundwater. Based on these observations, questions were raised regarding the potential effects of VOCs on the performance of the clay materials as a landfill liner.Laboratory experiments were conducted to evaluate the effects of three levels of soil precontamination and two types of permeants. Atterberg tests showed that the precontaminations (acetone and m-xylene) and the simulated leachate (methylene chloride, trichloroethylene, and toluene), at the concentrations used, did not impact clay-pore fluid interaction. Sedimentation tests showed that the impact of methylene chloride, trichloroethylene, and toluene on sediment volume and rate of settlement was not detectable up to the maximum concentration level of 100 ppm for each chemical.From the permeation tests, acetone in the precontaminated samples was generally flushed out within three pore volumes but m-xylene was not detected (above the detection limit of 0.01 mg 1⁻¹) in the permeant effluent. The stabilized permeabilities of the specimens ranged from 0.2 × 10⁻⁷ to 3.0 × 10⁻⁷ cms⁻¹. It was found that precontamination of the clay at the levels studied did not affect organic chemical leachate transport/adsorption discernibly when compared with clean clay, and no measurable retardation or adsorption of VOCs in clay liners occurred in either clean clay or precontaminated clay.     

Biodegradation Study of Starch-graft-Acrylonitrile Copolymer

In this study the biodegradability of starch-graft-acrylonitrile (St-g-AN) copolymer has been investigated using some microorganisms including Aspergillus niger. The fungus A. niger was isolated from the soil and from the wastewater of an acrylic fiber company. The effects of four factors including environment temperature, primary inoculum concentration, pH and weight of copolymer film, on the biomass generation as a measure of biodegradation rate of copolymer, were studied using Taguchi experimental design. The statistical analysis of the results showed that the primary inoculum concentration and temperature were the most important factors affecting the biodegradation of St-g-AN copolymer. The optimum levels of temperature, pH, inoculum concentration, and weight of films to attain the maximum biodegradation (as much as 8.59 % by weight percentage during 28 days) were obtained as 30 °C, 4.75, 10⁸ spore/mL, and 1.1 g, respectively. The changes in the structure and morphological properties of the copolymer before and after degradation were determined using transform infrared spectroscopy and scanning electron microscopy.     

Central Composite Design Model to Study Swelling of GrA-cl-poly(AAm) hydrogel and Kinetic Investigation of Colloidal Suspension

In the present study, the flocculation behavior of crosslinked copolymer GrA-cl-poly(AAm) hydrogel has been studied for the removal of turbidity from waste water. Sodium borohydride has been used for the reduction of the Gum rosin acids by which it gets converted into rosin alcohols. The reduced Gum rosin alcohol was crosslinked by the use of MBA and copolymerized with acrylamide using KPS as a redox initiator. Synthesized sample was then optimized for reaction conditions like reaction time, reaction temperature and the amount of solvent, monomer concentration, initiator concentration and pH of the reaction medium in order to get maximum percentage swelling. Synthesized samples were characterized using Fourier transform infrared spectroscopy, scanning electron of microscopy and X-ray diffraction techniques. Response surface methodology (RSM) based central composite design was used to study the effect of pH of swelling medium and temperature to maximize the percentage swelling. A statistical model (ANOVA) predicted pH 7.0 and temperature 40?°C as optimum operating conditions in order to get maximu swelling. GrA-cl-poly(AAm) hydrogel was found to be pH and temperature sensitive. Kaolin has been employed as a coagulant. The flocculation efficiency of the synthesized polymer was studied as a function of polymer dose, temperature and pH of the solution. GrA-cl-poly(AAm) observed to show maximum flocculation efficiency (95%) with 70mgL^?1 polymer dose in pH 5.0 at 30?°C. The adsorption capacity of malachite green dye removal (95%) was also studied with this synthesized polymer. The results validate that GrA-cl-poly(AAm) hydrogel has significant flocculation and dye removal properties and can be employed as an effective and low-cost material for removal of impurities from waste water.     

Enzyme-Assisted Extraction and Pb<Superscript>2+</Superscript> Biosorption of Polysaccharide from <Emphasis Type="Italic">Cordyceps militaris</Emphasis>

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb²⁺ from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L^?1), initial Pb²⁺ concentration (300 mg L^?1) and contact time (40 min) were outlined to enhance Pb²⁺ biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb²⁺ biosorption, suggesting the biosorption of Pb²⁺ onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.     

Adsorption of Pb2+ and Cd2+ on the l-cysteine-functionalized graphene oxide/chitosan/polyvinyl alcohol hydrogel: Kinetic,isotherm, and thermodynamic study

In this study, polyvinyl alcohol-chitosan-cysteine-functionalized graphene oxide (PCCFG) hydrogel was synthesized from l -cysteine-functionalized graphene oxide (CFG), chitosan (CS), and polyvinyl alcohol (PVA). The hydrogel was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy and employed for removing lead ion (Pb²⁺) and cadmium ion (Cd²⁺) from aqueous solution. The effects of initial metal ion concentration, hydrogel dose, pH, time, and temperature were studied. The experimental data were well described by a pseudo-second-order kinetic model and Langmuir isotherm with maximum adsorption capacities of 250 and 192 mg g⁻¹ at 25°C for Pb²⁺ and Cd²⁺, respectively. The adsorption capacity of the PCCFG hydrogel increased with an increase in temperature. The value of ∆G° was negative, which shows the spontaneity of the reaction (electron exchange or ion exchange) between the metal ion and electron-rich atoms (–N, –S, –O). The positive ∆H° shows that the adsorption reaction consumes energy and the positive ∆S° shows the strong affinity of PCCFG toward the Pb²⁺ and Cd²⁺ ions. Pb²⁺ had better affinity and less spontaneity than Cd²⁺. The results show that the coexistence of Pb²⁺, Cd²⁺, and Cu²⁺ in the solution inhibits the adsorption capacity of PCCFG.     

Effects of commercial bacterial products on nutrient transformations of pig manure in a pig-on-litter system

A preliminary study was carried out in an experimental farm in Hong Kong to investigate the changes in microbial populations and nutrient concentrations of a pig waste mixture during a 10-week in-situ decomposition of pig manure in a pig-on-litter system. The effects of two commercially available bacterial products on this decomposition process were also examined. The results show that both heterotrophs and nitrifiers increased their populations to 10¹⁵ MPN (Most Probable Number) g⁻¹ waste mixture at the end of the 10-week study while the denitrifiers varied around 10¹⁰ MPN g⁻¹ during the period of investigation. By contrast, the fungal Colony Forming Units (CFU) declined rapidly within the first week and remained at 105 CFU g⁻¹ waste mixture throughout the rest of the study period. There was no accumulation of inorganic N in the pig waste mixture. The offensive odour of NH, was not detected in the pig pens. The C:N ratios of the waste mixture gradually declined reaching a final value of 22:1. The concentration of total Kjeldahl N, phosphorus and potassium in the final product were significantly higher when compared with the initial phase of the study. These findings suggest that a part of the organic nutrients released from the pig manure might have been mineralized and assimilated into microbial biomass similar to compost. In general, the nutrient concentrations of the two pig waste mixtures treated by two different bacterial products were similar. This indicates that the effects of these two products on the in-situ decomposition of pig manure were fairly similar. A control pen without the addition of bacterial products became foul within one week and had to be abandoned.     

Investigation of the Thermosensitive Nanosphere Polymer in Removing Organophosphorus Pesticides from Water and Its Isotherm Study (Case Study: Diazinon)

In this research, a novel thermosensitive nanosphere polymer (TNP) was synthesized by copolymerization of N-isopropylacrylamide with 3-allyloxy-1,2-propanediol for the removal of diazinon from water. The characterization of the synthesized adsorbent has been performed by Fourier transform infrared spectrometer, scanning electron microscopy and elemental analysis. Batch adsorption method was performed to investigate the influences of various parameters like pH, temperature and contact time on the adsorption of diazinon. The equilibrium adsorption data of diazinon by TNP was studied by Langmuir, Freundlich, Temkin and Redlich–Peterson model. According to equilibrium adsorption results, the Langmuir, Freundlich and Temkin constants were evaluated to be 0.912 (L/mg), 7.916 (mg/g) (L/mg)^1/n and 2.494 respectively at pH 7 and room temperature. Based on Redlich–Peterson model analysis, the equilibrium data for the adsorption of diazinon was conformed well to the Langmuir isotherm model. This method was successfully applied for removal of diazinon from environmental samples. Moreover, in reusing of TNP, the sorption capacity was maintained without any significant change after 10 cycles of sorption–desorption process.     

Adsorption Efficiency of Polyaspartate-Montmorillonite Composite Towards the Removal of Pb(II) and Cd(II) from Aqueous Solution

The selective modification of sodium montmorillonite (Na⁺-Mt) surface with polyionene followed by poly (succinimde-co-aspartate) has been considered. Na⁺-Mt was allowed to react with well characterized polyionene in two fold excess. The resulting polyionene/Mt (IC) was further modified with poly (succinimide-co-aspartate) through an ion exchange process. The obtained polyaspartate/Mt (IPS) composite was characterized by elemental analysis, X-ray diffraction, FTIR spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and BET surface analyzer. The adsorption efficiency of IPS composite was investigated for the removal of Pb(II) and Cd(II) from aqueous solution under different experimental conditions including initial metal ions concentration, temperature and single and binary mixture systems of metal ions. The experimental data were analyzed by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models. Langmuir model reveals that the monolayer adsorption capacity of IPS was 92.59 and 67.57 mg/g for Pb(II) and Cd(II), respectively. The modification of parent Na⁺-Mt enhanced their adsorption capacity by about 87.91 and 29.84% for Pb(II) and Cd(II), respectively, due to inclusion of extra active sites of polyaspartate. The mean sorption energy, E calculated from Dubinin–Radushkevich isotherm were 2.75 and 1.98 kJ/mol for the adsorption of Pb(II) and Cd(II), respectively, indicating physical adsorption process. Also, The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic process. The mechanism of cation exchange and complexation of metal ions was suggested. IPS composite has a considerable potential for the removal of heavy metal ions from aqueous solution and wastewater stream.     

Experimental and Modeling Studies for the Removal of Crystal Violet Dye from Aqueous Solutions using Eco-friendly <Emphasis Type="Italic">Gracilaria corticata</Emphasis> Seaweed Activated Carbon/Zn/Alginate Polymeric Composite Beads

This research article describes, an eco-friendly activated carbon prepared from the Gracilaria corticata seaweeds which was employed for the preparation of biodegradable polymeric beads for the efficient removal of crystal violet dye in an aqueous solution. The presence of chemical functional groups in the adsorbent material was detected using FTIR spectroscopy. The morphology and physical phases of the adsorbent materials were analyzed using SEM and XRD studies respectively. Batch mode dye adsorption behavior of the activated carbon/Zn/alginate polymeric beads was investigated as a function of dosage, solution pH, contact time, initial dye concentration and temperature. Maximum dye removal was observed at a pH of 5.0, 1 g of adsorbent dosage with 60 mg/L dye concentration, 50 min of contact time and at 30 °C. The equilibrium modeling studies were analyzed with Freundlich and Langmuir adsorption isotherms and the adsorption dynamics was predicted with Lagergren’s pseudo-first order, pseudo-second order equations and intra particle diffusion models. The process of dye removal followed a pseudo second-order kinetics rather than pseudo first order. The thermodynamic parameters like standard Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined and the results imply that the adsorption process was spontaneous, endothermic and increases the randomness between the adsorbent and adsorbate. The results from the experimental and correlation data reveal that the Gracilaria corticata activated carbon/Zn/alginate polymeric beads have proved to be an excellent adsorbent material for the removal of CV dye.     

Diffusion coefficients of organics in high density polyethylene (HDPE)

Only limited data are available on the diffusion of volatile organic solvents through flexible membrane liners (FMLs) used for lining impoundments and landfills. To expand this database, a rapid, inexpensive method is needed to measure the diffusion coefficients of volatile organic solvents through FML materials. An absorption method has been developed to determine the diffusion coefficients of volatile organic solvents through FML materials. The method is based on the depletion of an organic compound from an aqueous solution due to absorption by a submerged sample of FML. A numerical solution of Fick's second law of diffusion was used to develop a graph which can be used to determine the diffusion coefficient from the time dependent concentration data. The diffusion coefficients obtained from the absorption tests were validated by comparing them with coefficients determined using a two chamber diffusion cell. The diffusion coefficients determined for toluene and xylene in high density polyethylene (HDPE) were 5.1 × 10⁻⁹ cm²s⁻¹ and 1.0 × 10⁻⁹ cm²s⁻¹ by the two methods, respectively. The data indicate that the coefficient of distribution (K_d) between the FML and the organic solution, a value which is needed to calculate the diffusion coefficient from the data, can be estimated from the log of the octanol-water partition coefficient (K_ow), a commonly measured and reported value for many chemicals.     

Integrated biogas technology in the tropics. 2. Use of slurry for fish culture

The composite slurry from four 3.5-m³ ferrocement digesters fed a mixture of nightsoil, water hyacinth (Eichhornia crassipes) and rice straw was loaded into four 200-m² earth fish ponds at organic loading rates of 25, 50, and 100 kg chemical oxygen demand (COD) ha⁻¹ day⁻¹. Impressive extrapolated net fish yields of about 10 kg ha⁻¹ day⁻¹ (3.7 ton ha⁻¹ year⁻¹) were obtained at the highest organic loading rate, equivalent to loading rates of about 120 kg total solids and 4.5 kg total Kjeldahl nitrogen ha⁻¹ day⁻¹. There may be potential for even greater yields from biogas slurry fed fish ponds because the relationship between net fish yield and slurry loading rate was linear. Constraints in the development of integrated biogas technology for poor farmers in the tropics are likely to be associated with the digester rather than with the reuse of slurry for fish culture.     

Oil Erosion in an Annular Flume by Seawater of Varying Turbidities: A Critical Bed Shear Stress Approach

Laboratory experiments were conducted in an annular flume using Hibernia crude oil to determine: (1) the critical shear stress (τ_c) necessary to remove stranded oil from a surface by resuspension and (2) the effect of suspended sediment concentrations (SSCs) on the oil erosion processes. Two types of erosion were evident: Type I––solution and erosion of soluble aromatics; and Type II––mass erosion of visible droplets. In particulate free seawater at 13 °C, the Type II erosion threshold τ_cII is 5.0 Pa. This is equivalent to a mean current velocity (U_y) of 0.55 m s⁻¹. At U_y values <0.55 m s⁻¹, Type I erosion occurred as shown by the increase of oil concentrations without visible erosion of the oil surface. Temperature has a strong control on the threshold and rate of oil erosion: the threshold for Type I erosion at 4 °C was higher and erosion rate lower than at 13 °C. No Type II erosion was observed at 4 °C. SSCs also affects the entrainment of oil. Oil erosion was most efficient at moderate SSCs. At very high SSCs, turbulence suppression and drag reduction became effective and oil erosion rate decreased. SSC at 200–250 mg l⁻¹ were observed to give maximum erosion efficiency and is therefore suggested as the optimal concentration for erosion and elimination of heavy crude oil at a water temperature of 13 °C.     

Adsorptive Removal of Malachite Green Chloride and Reactive Red-198 from Aqueous Solutions by Using Multiwall Carbon Nanotubes-Graft-Poly (2-acrylamido-2-methyl-1-propanesulfonic acid)

The multiwall carbon nanotubes (MWCNTs) were modified by 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) via grafting reaction and γ-rays of ⁶⁰Co source was used as initiator. The outcome product was called hydroxyethylated (HOEt-MWCNTs) graft poly(AMPS) and abbreviated as HOEt-MWCNTs-g-PAMPS. The parameters that affected the grafting yield were optimized. The maximum grafting obtained was ~20 %. HOEt-MWCNTs-g-PAMPS were characterized by Fourier transform infra red, scanning electron microscopy, high resolution transmission electron microscopy, thermal gravimetric analysis. The adsorptive removals of malachite green chloride (MGC) and reactive red 198 (RR-198) onto HOEt-MWCNTs-g-PAMPS were studied at variable conditions. The adsorption isotherms were analyzed using Langmuir, Redlich–Peterson, Freundlich, Khan and Sips models. The results referred that Sips model is the best fitting to adsorption of MGC and Freundlich model is the best fitting to RR-198 adsorption. The monolayer coverage capacities of HOEt-MWCNTs-g-PAMPS for MGC and RR-198 dyes were found 172 and 323 mg g^?1, respectively. The rate of kinetic adsorption processes of MGC and RR-198 onto HOEt-MWCNTs-g-PAMPS were described by using pseudo-first order, pseudo-second order and intraparticle diffusion models. The pseudo-first order and pseudo-second order models were the best choice among the kinetic models to depict the adsorption behaviors of MGC and RR-198 dyes onto HOEt-MWCNTs-g-PAMPS, respectively. Further, the effect of temperature on the adsorption isotherms was investigated and the thermodynamic parameters were obtained. The results indicated that the adsorption process is spontaneous and endothermic. The values of ΔG° varied in range with the mean values showing a gradual increase from ?3.17 to ?3.64 kJ mol^?1 for MGC and ?3.36 to ?3.73 kJ mol^?1 for RR-198. The reusability and regeneration of adsorbent were investigated. The outcome data referred to that the efficiency of adsorbent >98 %. The outline results declared that there is a good potentiality for the HOEt-MWCNTs-g-PAMPS to be used as an adsorbent for the removal of MGC and RR-198 from aqueous solutions.     

Impact on health of chlorinated dioxins and other trace organic emissions

The potential health effects of incineration of municipal solid waste (MSW) have been studied by the Swedish National Institute of Environmental Medicine.The greatest concern for health effects relates to the emission of PCDDs and PCDFs (“dioxins”). MSW incineration is presently estimated to be a large source for the emission of these compounds into ambient air. Based upon animal experiments, and by applying safety factors in the range 200–1000, a highest tolerable daily intake (TDI) has been estimated to be 1–5 pg kg⁻¹ of TCDD for humans. This TDI-value has been extended to cover all the congeners of PCDDs and PCDFs by the application of the concept of “TCDD-equivalents” (Eadon et al., 1983). The high concentrations found in human breast milk and fish indicate that the TDI value may be exceeded, especially among breast-milk fed babies. If the emission can be reduced to the proposed Swedish limit value of 0.1 ng m⁻³ n TCDD-equivalents, or less, the contribution from this source will be lowered. MSW incineration can be considered acceptable when the following aspects are taken into account: the risk estimation for TDI is conservative; there is no indication that man belongs to the most sensitive species although infants may be particularly sensitive; available studies indicate that the concept of TCDD-equivalents used overestimates the effect of mixtures of PCDDs and PCDFs; present levels in fish and human milk reflect the cumulative effect of many years of emission. Besides PCDDs and PCDFs, MSW incineration also gives rise to relatively high emissions of PAH, chlorinated PAH, phenols, benzenes and mutagenic substances under less well controlled combustion conditions. The emission of organic compounds is generally dependent on the combustion efficiency. If the combustion process is optimized and advanced flue-gas cleaning is applied so that the emission of TCDD-equivalents does not exceed 0.1 ng m⁻³, emission of other organics probably will not cause significant health hazards.     

Treatment of Stormwater using Fibre Filter Media

In this study, a high-rate fibre filter was used as a pre-treatment to stormwater in conjunction with in-line flocculation. The effect of operating the fibre filter with different packing densities (105, 115 and 125 kg/m³) and filtration velocities (20, 40, 60 m/h) with and without in-line flocculation was investigated. In-line flocculation was provided using 5, 10 and 15 mg/L of ferric chloride (FeCl₃·6H₂O). The filter performance was studied in terms of pressure drop (ΔP), solids removal efficiency, heavy metals (total) removal efficiency and total organic carbon (TOC) removal efficiency. It is found that the use of in-line flocculation at a dose of 15 mg/L improved the performance of fibre filter as measured by turbidity removal (95%), total suspended solids reduction (98%), colour removal efficiency (99%), TOC removal (reduced by 30–40 %) and total coliform removal (93%). The modified fouling index reduced from 750–950 to 12 s/L² proving that fibre filter can be an excellent pre-treatment to membrane filtration that may be consider as post-treatment. The removal efficiency of heavy metal was variable as their concentration in raw water was small. Even though the concentration of some of these metals such as iron, aluminium, copper and zinc were reduced, others like nickel, chromium and cadmium showed lower removal rates.     

SETTING DIOXIN EMISSION LIMITS FOR MSW INCINERATORS: A MULTIMEDIA EXPOSURE ASSESSMENT FRAMEWORK

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are emitted in trace amounts from municipal solid waste (MSW) incinerators. The exposure to PCDD/Fs experienced by an individual is dominated by the food chain pathway, which accounts for over 98% of the total uptake. Defining a target daily intake (the World Health Organization TDI of 10 pg I-TEQ kg.bw⁻¹day⁻¹) exposure assessment algorithms were then applied to arrive at the corresponding PCDD/F levels in air, soil, plants, food products, etc., which would allow the target intake to be met while retaining the balance of intake between the various exposure pathways. These concentrations were converted to an ambient air concentration of PCDD/Fs and ultimately, by defining criteria for acceptability, to a guide value for PCDD/F concentration in emissions from the MSW incinerator. This strategy was applied to PCDD/F emissions from MSW incinerators of various sizes against two illustrative criteria for acceptability: an “insignificant” release and a threshold above which the release may require further assessment for environmental effects and for control. Using the criteria developed in this paper, the current PCDD/F emission limit of 0.1 ng I-TEQ m⁻³results in an emission that is classed as “insignificant” for all plant sizes. However, higher emission concentrations can also be accommodated below the threshold for further assessment and control.     

Removal of Oil from Water by Calcium Alginate Hydrogel Modified with Maleic Anhydride

Calcium alginate hydrogel was prepared and used as a biosorbent for the removal of oil from aqueous solutions. Calcium alginate hydrogel was further chemically modified by esterification with maleic anhydride. The changes in the physicochemical properties of maleic anhydride modified calcium alginate were investigated via multiple techniques (FTIR, SEM, BET and DSC/TGA). Adsorption batch experiments were carried out to compare the oil adsorption capacities of native and modified calcium alginates. Adsorption experiments were carried out as a function of solution pH, temperature and ionic strength to determine the optimal conditions for the adsorption of oil. Equilibrium and kinetic studies were conducted for the modified alginate. Results revealed that the maleic anhydride modification of calcium alginate improved its adsorption capacity towards oil. Higher adsorption capacities of modified alginate were attained at lower temperatures (20 °C), higher ionic strengths (1.0 M NaCl) and within the pH range of 5–9. The oil adsorption data obtained for modified alginate could be better described by the first order kinetic model (R²?=?0.981) and the BET equilibrium isotherm (R²?=?0.984). The maximum monolayer adsorption capacity predicted by the BET model for the modified calcium alginate was found to be 143.0 mg/g.     

Effect of liquid-to-solid ratio on semi-solid Fenton process in hazardous solid waste detoxication

The liquid-to-solid ratio (L/S) of semi-solid Fenton process (SSFP) designated for hazardous solid waste detoxication was investigated. The removal and minimization effects of o-nitroaniline (ONA) in simulate solid waste residue (SSWR) from organic arsenic industry was evaluated by total organic carbon (TOC) and ONA removal efficiency, respectively. Initially, Box-Behnken design (BBD) and response surface methodology (RSM) were used to optimize the key factors of SSFP. Results showed that the removal rates of TOC and ONA decreased as L/S increased. Subsequently, four target initial ONA concentrations including 100 mg kg⁻¹, 1 g kg⁻¹, 10 g kg⁻¹, and 100 g kg⁻¹ on a dry basis were evaluated for the effect of L/S. A significant cubic empirical model between the initial ONA concentration and L/S was successfully developed to predict the optimal L/S for given initial ONA concentration for SSFP. Moreover, an optimized operation strategy of multi-SSFP for different cases was determined based on the residual target pollutant concentration and the corresponding environmental conditions. It showed that the total L/S of multi-SSFP in all tested scenarios was no greater than 3.8, which is lower than the conventional slurry systems (L/S ? 5). The multi-SSFP is environment-friendly when it used for detoxication of hazardous solid waste contaminated by ONA and provides a potential method for the detoxication of hazardous solid waste contaminated by organics.     

Airborne contaminants at waste treatment plants

Airborne contaminants in Finnish waste treatment plants were studied at two plants using mainly manual sorting and one incineration plant. Air samples were analysed for mesophilic and thermotolerant bacteria, mesophilic fungi, endotoxin, dust and heavy metals (lead, cadmium). The concentrations of mesophilic bacteria in the working air of the waste treatment plants were under 2 × 10⁴ colony forming units (cfu) m⁻³ and the concentrations of mesophilic fungi were under 7 × 10⁴ cfu m⁻³. There was no seasonal variation in the concentrations of bacteria, but the concentrations of fungi were highest in autumn at the waste incineration plant. The concentrations of microbes recorded with two sampling methods, the Andersen and Nuclepore filter methods, differed but were usually of the same order of magnitude. The identified bacteria did not include any potent pathogens. In manual sorting the level of organic dust reached 38 mg m⁻³, whereas the 8-h hygiene limit value for organic dust is 5mg m⁻³ and the 15-min hygiene limit value is 10 mg m⁻³. The endotoxin levels were all below 30 ng m⁻³ and the concentrations of heavy metals were low.     

Synthesis,Characterization and Application of α, β, and γ Cyclodextrin-Conjugated Graphene Oxide for Removing Cadmium Ions from Aqueous Media

In this study, a novel and facile route for the synthesis of cyclodextrin-conjugated graphene oxide (CDs–GO) nanocomposites by esterification reaction in the presence of EDC/DMAP as catalyst, was developed. The formation of CDs–GO was successfully approved by FT-IR, SEM, TEM, TGA and BET analyses. Then competitive adsorption capacity of cadmium ion by CDs–GO composites and the impact of different empirical parameters like contact time, initial metal ion concentration, and initial pH on the adsorption process were studied. The results showed that β-CD–GO at pH 7 is suitable for removing Cd(II) with 90?% removal efficiency. Also, the adsorption capacity experiment at constant concentration of 50 ppm of Cd(II) showed that more than 50?% of Cd(II) ions could be adsorbed by γ-CD–GO reaching an equilibrium within 2 h. Therefore, the γ-CD–GO and α-CD–GO showed high adsorption capacity toward Cd²⁺ (222.22 mg/g) which were pointedly more than that of β-CD–GO (208.33 mg/g). Furthermore, adsorption kinetics, isotherm studies, and thermodynamic analyses were evaluated. The adsorption data exhibited excellent fit to the pseudo-second-order (R²?>?0.99) and Freundlich isotherm models.