Anaerobic microbial degradation of poly (3-hydroxyalkanoates) with various terminal electron acceptors

The microbial degradation of poly (3-hydroxyalkanoates) (PHAs) under anaerobic conditions with various terminal electron acceptors was examined. Nitrate-reducing consortia were established using activated sludge, and PHAs were shown to be biodegradable under these conditions. A positive correlation between carbon dioxide production and nitrate reduction was demonstrated. Nitrous oxide accumulated as the main N-containing product of nitrate reduction. The amount of PHAs in activated sludge cultures decreased approximately 20% within 40 days of incubation. Attempts were made to establish iron- and sulfate-reducing consortia from spring water, yet it could not be demonstrated that the mixed cultures were capable of degrading PHAs. Pure cultures of iron- and sulfate-reducing bacteria could not utilize PHAs as sole carbon sources. Methanogenic environments sampled included pond sediment and rumen fluid. PHAs were fermented to methane and carbon dioxide after 10 weeks by a sediment consortium, with 43 to 57% of the substrate carbon transformed to methane. Although it could not be demonstrated that PHAs were biodegraded by a rumen fluid consortium, a facultative anaerobic bacterium, identified as aStaphylococcus sp., that could grow on PHAs was isolated from rumen fluid.     

Utilizing of Sugar Refinery Waste (Cane Molasses) for Production of Bio-Plastic Under Submerged Fermentation Process

In the present study, depending upon the availability and cheaper cost, different carbon source were tested for the production of PHAs (Polyhydroxyalkonoates) by soil bacterium Pseudomonas aeruginosa and it was found that sugar refinery waste (cane molasses) produced the maximum PHA (biodegradable polymer) which is precursor for bio-plastic development. Urea served as potent nitrogen source over other inorganic nitrogen sources in bio-plastic synthesis. Effect of different physical parameters viz; pH, temperature and agitation speed were also studied on PHA production. Batch cultivation kinetics under optimized cultural and physical condition showed maximum cell mass and PHA concentration of 7.32?±?0.2 and 5.60?±?0.3?g/L, respectively after 54.0?h of cultivation. Sugar refinery waste (Total sugar 4%) and urea (0.8%) improved the economics of the process which exhibited a yield (Y_P/X) of 0.70 with productivity of 0.11?g/L/h. PHA was further characterized as PHB by using Fourier Transform Infra-red Spectroscopy (FT-IR).     

High-Efficiency Production of Bioplastics from Biodegradable Organic Solids

Microbial polyhydroxyalkanoates (PHAs) have been extensively studied as environmentally friendly biodegradable thermoplastics. The major obstacle to wide acceptance of PHAs is their high price, mainly attributed to the costs of raw materials and polymer recovery. A large amount of organic solids are discarded from food production and consumption and may be used as carbonaceous raw materials for production of PHAs. A novel technology was investigated at bench-top scale to produce PHAs from food scraps. The harvested cell mass had a high PHA content (72.6% of dry cell mass), the same as obtained from pure glucose and organic acids. The organic solid was first digested in an acidogenic reactor in which about 60% solid was converted to fermentative products, including short-chain fatty acids. The four major acids were acetic, propionic, butyric, and lactic acids at concentrations of 6, 2, 27, and 33 g/L, respectively. The acids were transported through a membrane barrier via molecular diffusion to an airlift bioreactor, where the acids were utilized by an enriched culture of Ralstonia eutropha for PHA synthesis. Purification of fermentative acids was not performed in this molecular diffusion–based integration of acidogenesis and polymerization. By using a dialysis membrane as the barrier, the dry cell mass concentration and PHA content reached 22.7 g/L and 72.6%, respectively. The PHA was a copolymer of poly (3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) with 2.8 mole % of hydroxyvalerate.     

Test methods to aid in the evaluation of the diversion of biodegradable municipal waste (BMW) from landfill

This discussion explores one crucial point about the use of biodegradability indicators to monitor biological processes in organic solid waste treatment plants. Today, some different measures are being used for the determination of biodegradable organic matter and most of them are based on respiration indices (oxygen consumption or carbon dioxide production under aerobic conditions) or biogas production tests (under strict anaerobic conditions). However, it is not evident from scientific literature that both tests may be equivalent or comparable. This discussion includes the results obtained when trying to correlate both anaerobic and aerobic tests to complement the recent work published by Wagland et al. [Wagland, S.T., Tyrrel, S.F., Godley, A.R., Smith, R., 2009. Test methods to aid in the evaluation of the diversion of biodegradable municipal waste (BMW) from landfill. Waste Management 29, 1218–1226].     

Bioplastic Wastes: The Best Final Disposition for Energy Saving

The pressing need to reduce the consumption of non-renewable resources and the emission of greenhouse gases into the environment, in recent decades has led to the wide development of bio-based plastics that are produced from renewable sources, such as corn, wheat, oil seeds etc. Actually, the most important bio-based plastics on the market are the poly(lactic acid) (PLA) produced from Nature Works (USA) and the Mater-Bi, a starch based bioplastics, made from Novamont (Italy). The aim of this work is not only to assess the actual energy and greenhouse gases (GHGs) savings resulting from the production of bioplastics, compared with the production of conventional plastics, but also to analyze what might be the best final disposition of bioplastic wastes in order to maximize the energy saving. Therefore, by using the Life Cycle Assessment (LCA) methodology, LCAs cradle to gate and cradle to grave were carried out both for PLA and Mater-Bi, taking into consideration as final scenarios composting, incineration, anaerobic digestion and mechanical recycling processes. The work demonstrates how incineration, composting and anaerobic digestion processes are clearly under-performing, from an environmental point of view, with respect to the mechanical recycling process.     

Recent Advances in the Production, Recovery and Applications of Polyhydroxyalkanoates

Polyhydroxyalkanoates (PHAs) are biodegradable and biocompatible polyesters that can potentially replace certain plastics derived from petroleum. PHAs can be produced using a combination of renewable feedstocks and biological methods. Native and recombinant microorganisms have been generally used for making PHAs via fermentation processes. As much as 90 % of the microbial dry mass may accumulate as PHAs. A range of PHAs has been produced using fermentation methods, including copolymers and block copolymers. Alternative production schemes based on genetically modified plants are becoming established and may become the preferred route for producing certain PHAs. Production in plants is likely to be inexpensive compared to production by fermentation, but it does not appear to be as versatile as microbial synthesis in terms of the range of products that may be generated. Cell-free enzymatic production of PHAs in vitro is receiving increasing attention and may become the preferred route to some specialty products. This review discusses the recent advances in production of polyhydroxyalkanoates by the various methods. Methods of recovering the polymer from microbial biomass are reviewed. Established and emerging applications of PHAs are discussed.     

Carbon--making the right choice for waste management in developing countries

Due to initiatives such as the clean development mechanism (CDM), reducing greenhouse gas emissions for a developing country can offer an important route to attracting investment in a variety of qualifying project areas, including waste management. To date CDM projects have been largely confined to schemes that control emission from landfill, but projects that avoid landfilling are beginning to be submitted. In considering the waste options which might be suitable for developing countries certain ones, such as energy from waste, have been discounted for a range of reasons related primarily to the lack of technical and other support services required for these more sophisticated process trains. The paper focuses on six options: the base case of open dumping; three options for landfill (passive venting, gas capture with flaring, and gas capture with energy production), composting and anaerobic digestion with electricity production and composting of the digestate. A range of assumptions were necessary for making the comparisons based on the effective carbon emissions, and these assumptions will change from project to project. The highest impact in terms of carbon emissions was from using a sanitary landfill without either gas flaring or electricity production; this was worse than the baseline case using open dumpsites. Landfills with either flaring or energy production from the collected gas both produced similar positive carbon emissions, but these were substantially lower than both open dumping and sanitary landfill without flaring or energy production. Composting or anaerobic digestion with energy production and composting of the digestate were the two best options with composting being neutral in terms of carbon emissions and anaerobic digestion being carbon negative. These generic conclusions were tested for sensitivity by modifying the input waste composition and were found to be robust, suggesting that subject to local study to confirm assumptions made, the opportunity for developing CDM projects to attract investment to improved waste management infrastructure is significant. Kyoto credits in excess of 1 tCO2e/t of waste could be realised.     

Biosynthesis of poly-(R)-3-hydroxyalkanoate: An emulsion polymerization

Poly-(R)-3-hydroxyalkanoates (PHAs) are bacterial storage polyesters, which are accumulated by a wide variety of microorganisms as a reserve of carbon and energy. Currently, these biopolymers are receiving much attention because of their potential application as biodegradable and biocompatible plastics. The polymer appears as submicron intracellular granules. The biosynthesis of these granules has been studied extensively but many observations remain inexplicable. This paper draws an analogy between the process of emulsion polymerization and that of granule formation. This analogy may explain many of the unknown features of granule formation and may also lead to useful applications of granules as latex products.     

Biodegradable Soy-Based Plastics: Opportunities and Challenges

Today's plastics are designed with little consideration for their ultimate disposability or the effect of the resources (feedstocks) used in making them. This has resulted in mounting worldwide concerns over the environmental consequences of such materials when they enter the mainstream after their intended uses. This led to the concept of designing and engineering new biodegradable materials–materials that have the performance characteristics of today's materials but that undergo biodegradation along with other organic waste to soil humic materials. Hence, the production of biodegradable materials from annually renewable agricultural feedstocks has attracted attention in recent years. Agricultural materials such as starches and proteins are biodegradable and environmentally friendly. Soybean is a good candidate for manufacturing a large number of chemicals, including biodegradable plastics, as it is abundantly available and cheap. Soy protein concentrate, isolate, or flakes could be compounded with synthetic biodegradable plastics such as polycaprolactone or poly (lactic acid) to make molded products or edible films or shopping bags and make the environment cleaner and greener.     

Biodegradability of degradable plastics exposed to anaerobic digested sludge and simulated landfill conditions

The biodegradabilities of various plastics by anaerobic digested sludge were measured and compared with the biodegradabilities under simulated landfill conditions. Bacterial poly(3-hydroxy-butyrate-co-3-hydroxyvalerate) (PHB/HV; 92/8, w/w), a natural aliphatic polyester, degraded nearly to completion within 20 days of cultivation by anaerobic digested sludge, while synthetic aliphatic polyesters such as poly-lactic acid, poly(butylene succinate), and poly (butylene succinate-co-ethylene succinate) did not degrade at all in 100 days. Cellophane, which was used as a control material, exhibited a similar degradation behavior to PHB/HV. Under simulated landfill conditions, PHB/HV degraded quite well within 6 months. Synthetic aliphatic polyesters also showed significant weight losses through 1 year of cultivation. The acidic environment inside simulators generated by the degradation of biodegradable food wastes which comprised 34 % of municipal solid waste seems to cause the weight loss of synthetic aliphatic polyesters.     

Poly(hydroxyalkanoates) from fluorescent pseudomonads in retrospect and prospect

Poly[(R)-3-hydroxyalkanoates] (PHAs) are biopolymers stored by bacteria, which are currently receiving much attention because of their potential as renewable and biodegradable plastics. Most well-known representatives are poly[(R)-3-hydroxybutyrate] and its copolymers with 3-hydroxyvalerate, which have been commercialized under the trademark Biopol. In addition to these rigid materials, the elastomeric medium-chain length PHAs (mcl-PHAs) produced by fluorescent Pseudomonads are now emerging. The present review aims to survey the important developments concerning research and application prospects of mcl-PHAs.     

A complete mass balance of a complex combined anaerobic/aerobic municipal source-separated waste treatment plant

In this study a combined anaerobic/aerobic full-scale treatment plant designed for the treatment of the source-separated organic fraction of municipal solid waste (OFMSW) was monitored over a period of one year. During this period, full information was collected about the waste input material, the biogas production, the main rejects and the compost characteristics. The plant includes mechanical pre-treatment, dry thermophilic anaerobic digestion, tunnel composting system and a curing phase to produce compost. To perform the monitoring of the entire plant and the individual steps, traditional chemical methods were used but they present important limitations in determining the critical points and the efficiency of the stabilization of the organic matter. Respiration indices (dynamic and cumulative) allowed for the quantitative calculation of the efficiency of each treatment unit. The mass balance was calculated and expressed in terms of Mgy(-1) of wet (total) matter, carbon, nitrogen and phosphorus. Results show that during the pre-treatment step about 32% of the initial wet matter is rejected without any treatment. This also reduces the biodegradability of the organic matter that continues to the treatment process. About 50% of the initial nitrogen and 86.4% of the initial phosphorus are found in the final compost. The final compost also achieves a high level of stabilization with a dynamic respiration index of 0.3±0.1g O(2) per kg of total solids per hour, which implies a reduction of 93% from that of the raw OFMSW, without considering the losses of biodegradable organic matter in the refuse (32% of the total input). The anaerobic digestion process is the main contributor to this stabilization.     

Introducing mechanical biological waste treatment in South Africa: a comparative study

This paper presents the results of the first pilot project on mechanical biological waste treatment (MBWT) in South Africa. The study has shown that biological waste treatment in windrows using a passive aeration system that utilises thermal convection to drive the aeration process within a windrow of waste is appropriate for South Africa, in relation to low capital costs, low energy inputs, limited plant requirements and potential for labour-intensive operations. The influence of climate, waste composition and operational facilities was evaluated to optimise the treatment technique to local conditions. The maximum temperatures reached during the intensive thermophilic stage were effectively equivalent to the German experience. The lower CO2 production experienced in the South African trials was attributed to a different waste stream (high presence of plastics) due to the absence of a proper source separated waste collection system. An accurate adjustment of the input material (structural matter in particular) to the specific ambient conditions and irrigation during composting should result in higher organic carbon degradation efficiency in equivalent timeframes. This preliminary experience suggests that the applicability of MBWT in emerging countries, such as South Africa, is directly dependant on the mechanical treatment steps, available operational facilities and nature of the input material.     

Optimal utilization of waste-to-energy in an LCA perspective

Energy production from two types of municipal solid waste was evaluated using life cycle assessment (LCA): (1) mixed high calorific waste suitable for production of solid recovered fuels (SRF) and (2) source separated organic waste. For SRF, co-combustion was compared with mass burn incineration. For organic waste, anaerobic digestion (AD) was compared with mass burn incineration. In the case of mass burn incineration, incineration with and without energy recovery was modelled. Biogas produced from anaerobic digestion was evaluated for use both as transportation fuel and for heat and power production. All relevant consequences for energy and resource consumptions, emissions to air, water and soil, upstream processes and downstream processes were included in the LCA. Energy substitutions were considered with respect to two different energy systems: a present-day Danish system based on fossil fuels and a potential future system based on 100% renewable energy. It was found that mass burn incineration of SRF with energy recovery provided savings in all impact categories, but co-combustion was better with respect to Global Warming (GW). If all heat from incineration could be utilized, however, the two alternatives were comparable for SRF. For organic waste, mass burn incineration with energy recovery was preferable over anaerobic digestion in most impact categories. Waste composition and flue gas cleaning at co-combustion plants were critical for the environmental performance of SRF treatment, while the impacts related to utilization of the digestate were significant for the outcome of organic waste treatment. The conclusions were robust in a present-day as well as in a future energy system. This indicated that mass burn incineration with efficient energy recovery is a very environmentally competitive solution overall.     

How to engineer biological processes that neutralize hazardous wastes

Because bioremediation must satisfy the fundamental biological tastes of specific organisms, environmental engineers must create a nutritious waste stew. Waste-hungry organisms need a proper electron acceptor. Oxygen is preferred; if it is not available, nitrate, sulfate, or carbon dioxide may work. The waste itself is a source of carbon and energy. Macronutrients are next—including phosphorus, nitrogen, and certain metals, if they are not already present in the wastewater—as well as micronutrients. Other factors, including pH, temperature, aeration, and mixing must suit the organisms' natural temperaments. This article explores how bioengineers can combine these ingredients in precise quantities and proportions in both conventional and innovative aerobic and anaerobic bioprocesses, including in situ treatment and even composting, to make the organisms healthy, happy, and inexpensive.     

Stable isotope signatures for characterising the biological stability of landfilled municipal solid waste

Stable isotopic signatures of landfill leachates are influenced by processes within municipal solid waste (MSW) landfills mainly depending on the aerobic/anaerobic phase of the landfill. We investigated the isotopic signatures of δ¹³C, δ²H and δ¹⁸O of different leachates from lab-scale experiments, lysimeter experiments and a landfill under in situ aeration. In the laboratory, columns filled with MSW of different age and reactivity were percolated under aerobic and anaerobic conditions. In landfill simulation reactors, waste of a 25 year old landfill was kept under aerobic and anaerobic conditions. The lysimeter facility was filled with mechanically shredded fresh waste. After starting of the methane production the waste in the lysimeter containments was aerated in situ. Leachate and gas composition were monitored continuously. In addition the seepage water of an old landfill was collected and analysed periodically before and during an in situ aeration.We found significant differences in the δ¹³C-value of the dissolved inorganic carbon (δ¹³C-DIC) of the leachate between aerobic and anaerobic waste material. During aerobic degradation, the signature of δ¹³C-DIC was mainly dependent on the isotopic composition of the organic matter in the waste, resulting in a δ¹³C-DIC of ?20‰ to ?25‰. The production of methane under anaerobic conditions caused an increase in δ¹³C-DIC up to values of +10‰ and higher depending on the actual reactivity of the MSW. During aeration of a landfill the aerobic degradation of the remaining organic matter caused a decrease to a δ¹³C-DIC of about ?20‰. Therefore carbon isotope analysis in leachates and groundwater can be used for tracing the oxidation–reduction status of MSW landfills.Our results indicate that monitoring of stable isotopic signatures of landfill leachates over a longer time period (e.g. during in situ aeration) is a powerful and cost-effective tool for characterising the biodegradability and stability of the organic matter in landfilled municipal solid waste and can be used for monitoring the progress of in situ aeration.     

Control of GHG emission at the microbial community level

All organic material eventually is decomposed by microorganisms, and considerable amounts of C and N end up as gaseous metabolites. The emissions of greenhouse relevant gases like carbon dioxide, methane and nitrous oxides largely depend on physico-chemical conditions like substrate quality or the redox potential of the habitat. Manipulating these conditions has a great potential for reducing greenhouse gas emissions. Such options are known from farm and waste management, as well as from wastewater treatment. In this paper examples are given how greenhouse gas production might be reduced by regulating microbial processes. Biogas production from manure, organic wastes, and landfills are given as examples how methanisation may be used to save fossil fuel. Methane oxidation, on the other hand, might alleviate the problem of methane already produced, or the conversion of aerobic wastewater treatment to anaerobic nitrogen elimination through the anaerobic ammonium oxidation process might reduce N2O release to the atmosphere. Changing the diet of ruminants, altering soil water potentials or a change of waste collection systems are other measures that affect microbial activities and that might contribute to a reduction of carbon dioxide equivalents being emitted to the atmosphere.     

Current EU-27 technical potential of organic waste streams for biogas and energy production

Anaerobic digestion of organic waste generated by households, businesses, agriculture, and industry is an important approach as method of waste treatment – especially with regard to its potential as an alternative energy source and its cost-effectiveness. Separate collection of biowaste from households or vegetal waste from public green spaces is already established in some EU-27 countries. The material recovery in composting plants is common for biowaste and vegetal waste. Brewery waste fractions generated by beer production are often used for animal feeding after a suitable preparation. Waste streams from paper industry generated by pulp and paper production such as black liquor or paper sludge are often highly contaminated with toxic substances. Recovery of chemicals and the use in thermal processes like incineration, pyrolysis, and gasification are typical utilization paths. The current utilization of organic waste from households and institutions (without agricultural waste) was investigated for EU-27 countries with Germany as an in-depth example. Besides of biowaste little is known about the suitability of waste streams from brewery and paper industry for anaerobic digestion. Therefore, an evaluation of the most important biogas process parameters for different substrates was carried out, in order to calculate the biogas utilization potential of these waste quantities. Furthermore, a calculation of biogas energy potentials was carried out for defined waste fractions which are most suitable for anaerobic digestion. Up to 1% of the primary energy demand can be covered by the calculated total biogas energy potential. By using a “best-practice-scenario” for separately collected biowaste, the coverage of primary energy demand may be increased above 2% for several countries. By using sector-specific waste streams, for example the German paper industry could cover up to 4.7% and the German brewery industry up to 71.2% of its total energy demand.     

Composting,anaerobic digestion and biochar production in Ghana. Environmental–economic assessment in the context of voluntary carbon markets

In some areas of Sub-Saharan Africa appropriate organic waste management technology could address development issues such as soil degradation, unemployment and energy scarcity, while at the same time reducing emissions of greenhouse gases. This paper investigates the role that carbon markets could have in facilitating the implementation of composting, anaerobic digestion and biochar production, in the city of Tamale, in the North of Ghana. Through a life cycle assessment of implementation scenarios for low-tech, small scale variants of the above mentioned three technologies, the potential contribution they could give to climate change mitigation was assessed. Furthermore an economic assessment was carried out to study their viability and the impact thereon of accessing carbon markets. It was found that substantial climate benefits can be achieved by avoiding landfilling of organic waste, producing electricity and substituting the use of chemical fertilizer. Biochar production could result in a net carbon sequestration. These technologies were however found not to be economically viable without external subsidies, and access to carbon markets at the considered carbon price of 7 EUR/ton of carbon would not change the situation significantly. Carbon markets could help the realization of the considered composting and anaerobic digestion systems only if the carbon price will rise above 75–84 EUR/t of carbon (respectively for anaerobic digestion and composting). Biochar production could achieve large climate benefits and, if approved as a land based climate mitigation mechanism in carbon markets, it would become economically viable at the lower carbon price of 30 EUR/t of carbon.     

Effect of Cross-Linking Waste Protein with Dialdehydes on Its Biodegradation Under Anaerobic Conditions

Most native polymers used in processing and application technologies are admittedly disposable from the environment in a biologic manner, but products possess low mechanical strength. One of the paths to increasing this attribute (if feasible) is their cross-linking, which may, however, affect their readiness to biodegradation. In the presented work this condition was observed on the example of waste protein (Hykol B) cross-linking by means of glutardialdehyde and glyoxal. Degree and course of cross-linking were determined through impedance spectroscopy. The objective of this work also was to obtain data for constructing a sensor capable of following the cross-linking course in real time, for potential industrial application of Hykol in continuous production. Impedance spectroscopy proved to be applicable even to this kind of material marked by considerable water content and exhibiting relatively high electric conductivity; so far it had been used only for materials of low conductivity. An aqueous environment inoculated with digested anaerobic sludge from a municipal wastewater treatment plant was selected for modeling anaerobic conditions. The relation was studied between cross-linking degree given by content of cross-linking agent (determined by impedance spectroscopy) and biodegradation degree under anaerobic conditions. It was confirmed that network density as given by quantity of added agent not only reduced breakdown degree but also slowed the course of the process. This fact is particularly obvious with cross-linking by means of glyoxal; network density is thus dependent on type of employed substance, which affect type and structure of created network. That not merely forms an obstacle during polymer swelling and dissolution but also prevents access of bacteria to source of metabolized organic carbon.