Process Optimization for the Preparation of Beta-cyhalothrin Microspheres by Using the Response Surface Methodology

Journal of Polymers and the Environment - Microcapsulses can effectively encapsulate, protect, and control the release of insecticides. In this study, emulsion–solvent evaporation method was...     

Optimization of Polyhydroxyalkanoates Production from Thermus thermophilus HB8 Using Response Surface Methodology

The thermophilic bacterium Thermus thermophilus HB8 was used for the overproduction of polyhydroxyalkanoates (PHAs) using a mathematical approach for the first time for optimization of process variables. In addition, the combined effect of nitrogen and phosphate concentrations on PHAs production was also investigated. A five-level-three-factor central composite rotary design was employed in combination with response surface methodology (RSM) to optimize the process variables for the production of PHAs in Thermus thrermophilus HB8. The three independent variables studied in the work were cultivation time, C/N ratio and phosphate concentration. Two second-order polynomial equations were obtained for biomass and PHA production by multiple regression analysis using RSM. The statistical analyses of the results showed that all the three variables had significant impact both on the cell growth and polymer accumulation. The model predicted a maximum PHA production of 0.47?g/L which represents the 42?% of dry cell weight (DCW) after 55?h of cultivation and with on setting the C/N ratio at 9:1?g/g and phosphate concentration at 20?mM. Verification of the predicted value resulted into a PHA production of 0.44?g/L (40.36?% of DCW).     

Statistical Optimization of Polyhydroxybutyrate Production by <Emphasis Type="Italic">Bacillus Pumilus</Emphasis> H9 Using Cow Dung as a Cheap Carbon Source by Response Surface Methodology

A gram positive bacterium (designated strain H9) found to be a potential polyhydroxybutyrate (biodegradable polymer) producer was isolated from the soil samples of a stress prone environment (municipal waste areas). This bacterium was identified as Bacillus pumilus H9 from its morphological, physiological and 16S rRNA gene sequence analysis. A four-factor central composite rotary design was employed to optimize the medium and to find out the interactive effects of four variables, viz. concentrations of cow dung, sucrose, peptone and pH on PHB production. Using response surface methodology, a second-order polynomial equation was obtained by multiple regression analysis and a yield of 2.47 g/L of PHB dry weight was achieved from the optimized medium at pH 7. Here, we report cow dung as a cheap carbon source for the production of PHB. Further, phbA, phbB and phbC genes were amplified by polymerase chain reaction which confirms the bacterium to be able to produce polyhydroxybutyrate.     

磁絮凝处理废水工艺条件的响应曲面法优化研究

以聚硅硫酸铁(PFSS)为絮凝剂、磁流体为磁种,采用磁絮凝法处理模拟废水。在正交实验基础上,利用Matlab软件进行响应曲面分析,研究磁絮凝法处理模拟废水的各因素间具有的交互作用关系。回归拟合结果表明最佳工艺条件为:PFSS加入量36.8g/L,模拟废水pH7.4,磁种加入量14.7mg/L,搅拌转速266r/min。在最佳工艺条件下进行实验,TP去除率为97.70%。     

响应面法优化烧烤竹炭对水中磷的吸附条件

采用响应面法优化烧烤竹炭(BBC)对水中磷的吸附条件。用Box-Behnken Design实验设计考察初始磷质量浓度、BBC粒径、BBC加人量和初始溶液pH等因素对磷去除率的影响。实验结果表明:各因素对磷去除率影响的大小顺序依次为初始溶液pHBBC粒径初始磷质量浓度BBC加入量;BBC吸附水中磷的最佳反应条件为初始磷质量浓度26.81 mg/L,BBC粒径0.15 mm,BBC加入量10.6 g/L,初始溶液pH 4.42;在最佳反应条件下,BBC对磷的去除率达90.04%。     

Optimized Removal of Acid Blue 62 from Textile Waste Water by SBA-15/PAMAM Dendrimer Hybrid Using Response Surface Methodology

SBA-15/PAMAM Nano adsorbent was synthesized by the proficiency of SBA-15 as an original compound, 3-chloropropyltrimethoxysilane as a bridge chemical compound and polyamidoamine dendrimer (PAMAM) in the role of a multifunctional amine end group for adsorption of acid blue 62 (AB62) from aqueous media. The synthesized adsorbent was characterized by transmission electron microscope, field emission scanning electron microscope and Fourier-transform infrared spectroscope. A response surface methodology was employed to evaluate the simple and amalgamated factors of the operating variables subtending initial pH (2–12), adsorbent dosage(0.01–0.03 g), contact time (5–120 min), initial dye concentration (40–600 ppm) and temperature (25–45?°C) to optimize the operating statues of the treatment method. These parameters were altered at five levels pursuant to the central composite design to appraise their effects on AB62 removal through analysis of variance. Analysis of variance represented a high coefficient of definition amount (R²?=?0.9999) and acceptable prediction quadratic polynomial model was concluded which ascertain the suitability of the model and a high correlation among the predicted and empirical amounts. Utmost color removal efficiency was auspicated and empirically accredited. The optimum conditions relied on acquired results for AB62 removal were at an initial pH of 2, adsorbent dosage of 0.03 g SBA-15/PAMAM, dye concentration of 40 mg l^?1, time contact of 60 min and temperature of 25?°C.     

Modelling and Optimization of Uranium (VI) Ions Adsorption Onto Nano-ZnO/Chitosan Bio-composite Beads with Response Surface Methodology (RSM)

Nano-ZnO-chitosan bio-composite beads were prepared for the sorption of \({\text{UO}}_{2}^{{2+}}\) from aqueous media. The resulting nano-ZnO/CTS bio-composite beads were characterized by TEM, XRD etc. The sorption of \({\text{UO}}_{2}^{{2+}}\) by bio-composite beads was optimized using RSM. The correlation between four variables was modelled and studied. According to RSM data, correlation coefficients (R²?=?0.99) and probability F-values (F?=?2.24?×?10^??10) show that the model fits the experimental data well. Adsorption capacity for nano-ZnO/CTS bio-composite beads was obtained at 148.7 mg/g under optimum conditions. The results indicate that nano-ZnO/CTS bio-composite beads are appropriate for the adsorption of \({\text{UO}}_{2}^{{2+}}\) ions from aqueous media. Also, the suitability of adsorption values to adsorption isotherms was researched and thermodynamic data were calculated.     

Influence of the Concentrations of Chitosan and Glycerol on Edible Film Properties Showed by Response Surface Methodology

The individual and interactive effects of glycerol and chitosan concentrations on edible film properties were investigated using response surface methodology. The results of ANOVA indicated that all the independent variables exhibited significant effect on the film properties. Chitosan concentration had a positive effect on CO₂ permeability and negative effect on O₂ while the glycerol concentration had a positive effect on permeability to both gases. Regarding water vapor permeability, the chitosan concentration had a negative effect, whereas the glycerol had no influence. Moreover, both chitosan and glycerol concentration influenced the elongation at break point (%A), and only glycerol concentration had a significant effect on tensile strength. Optimization by desirability approach was carried out on the independent variables to get the optimum levels within the experimental conditions. It was found that 1.5 % of chitosan and 25 % of glycerol (wt/wt of chitosan) retarded respiration and showed a strong permeability to water vapor.     

Improvements in Air Quality Modelling by Using Surface Boundary Layer Parameters derived from Satellite Land Cover Data

Many atmospheric dispersion models include only simpletreatment of surface features to estimate the wind profilesand stability parameters. Detailed characterisation of theland cover, particularly in large and complex urbanconurbations, is especially important, as the surfacefeatures can vary significantly over the area. This paperdiscusses the use of satellite land cover data to derivespatially resolved surface boundary layer (SBL) parameters.These parameters have been used in an air quality model,PEARL (Prediction Air Quality in Urban and RegionalLocations) for estimating monthly and annual COconcentrations. Land cover data, derived from LANDSATThematic Mapper Imagery, has been used to estimate SBLparameters (surface roughness length, albeedo, Bowen ratioand anthropogenic heat flux) for a study area of 10000km² encompassing Greater London and the surroundingcounties. The SBL parameters have been assigned according tomajor land cover types for the whole area at a spatialresolution of 1 × 1 km. Predictions from two versions of the PEARL model (one with land cover data and one without)have been compared with each other and with measured data forannual and monthly CO concentrations from seven London airquality monitoring sites. This comparison shows thatdifferences between predicted and observed values can bereduced by up to a factor of three. The use of SBLparameters derived from land cover data also yields moredetailed predicted annual CO spatial patterns especially inand around suburban areas. The performance of both versionsof the model for monthly CO concentrations has been comparedwith a range of statistical measures. This comparisonconfirms that improved agreement is observed betweenmodelled and measured monthly CO concentrations when use ismade of spatially resolved SBL parameters.     

Thorium(IV) Recovery from Water and Sea Water Using Surface Modified Nanocellulose/Nanobentonite Composite: Process Design

Thorium(Th) contamination in the ground water an emerging environmental issue and Th recovery from sea water and nuclear wastewater is of high significance, as it is a major player in the energy sector. For the adsorption and recovery of Th, polymer grafted bio materials are reported as most efficient materials. P(IA/MAA)-g-NC/NB was prepared and all the steps in the synthetic routes were monitored using FTIR, SEM–EDS, and XRD, TG. Efficiency in removal of Th(IV) by P(IA/MAA)-g-NC/NB was tested by batch adsorption technique. The pH dependent Th(IV) adsorption process, was optimized at 4.5 and adsorption equilibrium was achieved within 120 min. Experimental kinetic data correlates well with pseudo-second-order equation, indicates adsorption was chemical process via ion exchange followed by complexation reaction, also could explain the film diffusion process of adsorption. Sips isotherm proved to best fit for the adsorption of Th(IV) onto P(IA/MAA)-g-NC/NB with maximum adsorption capacity of 95.19 mg/g. Thermodynamic studies revealed the endothermic nature, feasibility and spontaneity of the adsorption process. ΔHx and ΔSx were decreased to a small extent from ?5.567 to ?3.439 kJ/mol and increased from 11.18 to 18.39 J/mol, respectively, with increase in surface loading from 50 to 70 mg/g, indicating that the surface of the onto P(IA/MAA)-g-NC/NB is having energetically heterogeneous surface and there may be some lateral interactions between the adsorbed Th(IV) ions Repeated adsorption–desorption study over six cycles, adsorption percentage decreases from 99.0 to 94.6 %, proved the efficiency of P(IA/MAA)-g-NC/NB as an effective adsorbent for the removal and recovery of Th(IV) from aqueous solutions. Complete removal of Th(IV) ions from seawater containing 10 mg/L with a dose of 0.25 g/L P(IA/MAA)-g-NC/NB achieved. Batch adsorption system as double stage reactor designed from the adsorption isotherm data of Th(IV) by constructing operational lines. From these could be concluded that P(IA/MAA)-g-NC/NB is a promising candidate for the effective removal and removal of Th(IV) from industrial effluents phase and sea water. The maximum adsorption capacity Qs for Ceralite IRC-50 calculated which was found to be 179.67 mg/g which are considerably lower than those for P(IA/MAA)-g-NC/NB.     

Green Synthesis of Silver Nanoparticles Using Exopolysaccharides Produced by Bacillus anthracis PFAB2 and Its Biocidal Property

Journal of Polymers and the Environment - Nowadays when control of environmental toxicity is a matter of concern, the focus of the researchers is to find an eco-friendly process. Considering the...     

乙烯废碱液的ZnO沉淀法脱硫过程优化与动力学研究

采用ZnO沉淀法对乙烯废碱液进行脱硫,通过正交实验确定的最佳工艺条件为:反应温度80～85℃,n(ZnO)∶n(Na2S)=0.9,反应时间150min。在上述最佳工艺条件下,废碱液脱硫率和ZnS质量分数可分别达88%和95%以上。动力学研究结果表明,ZnO沉淀法的脱硫速率可用简化的Na2S浓度的幂函数模型描述,该模型的Na2S转化率计算值与实验值吻合良好。     

Surface Modification of Sisal Fibers (Agave sisalana) Using Bacterial Cellulase and Methyl Methacrylate

The hydrophilic nature of cellulose fibers often results in poor compatibility with hydrophobic polymer matrices. Therefore, it becomes necessary to modify the surface of natural fiber for better binding between fiber and matrix. Chemicals are commonly used for the modification of cellulosic materials but large amount of solvents are usually involved. Microwave radiation induced grafting is one of the promising methods for the surface modification of natural fibers. In the present paper, we have reported the microwave radiations induced grafting onto sisal fibers (Agave sisalana) using methyl methacrylate monomer, which has been compared to the surface modification of sisal fibers using bacterial cellulase. The effects of these treatments on the properties of sisal fibers are discussed in the present paper. The modified fibers were characterized by scanning electron microscopy, X-ray diffraction, and thermogravimetric analysis/differential thermal analysis techniques to determine their morphology, crystallinity and thermal stability.     

Simultaneous Determination and Optimization of Titan Yellow and Reactive Blue 4 Dyes Removal Using Chitosan@hydroxyapatite Nanocomposites

Journal of Polymers and the Environment - Chitosan (CS) and hydroxyapatite (HA) nanocomposites have been prepared and used for the simultaneous removal of Titan Yellow (TY) and Reactive Blue 4 (RB...     

PLA and Organoclays Nanocomposites: Degradation Process and Evaluation of ecotoxicity Using Allium cepa as Test Organism

In this study, nanocomposites of PLA and organoclays Cloisite 20A and Cloisite 30B were prepared by the melt intercalation method and the obtained samples were characterized by transmission electron microscopy (TEM). Since composting is an important proposal to the final disposal of biopolymers, the influence of clays on the hydrolytic degradation process of PLA was evaluated by visual analysis and monitoring of molecular weight after periods of 15 and 30 days of degradation in compost. After degradation of the materials in composting environment, the evaluation of cytotoxic, genotoxic and mutagenic effects of compost aqueous extract was carried out using a bioassay with Allium cepa as test organism. The TEM micrographs permitted the observation of different levels of dispersion, including exfoliated regions. In the evaluation of hydrolytic degradation it was noted that the presence of organoclays can decrease the rate of degradation possibly due to the barrier effect of clay layers and/or the higher degree of crystallinity in the nanocomposite samples. Nevertheless, even in the case of nanocomposites, the molecular weight reduction was significant, indicating that the composting process is favorable to the chain scission of PLA in studied materials. In the analysis performed by the bioassay using A. cepa as test organism, it was found that after degradation of the PLA and its nanocomposites the aqueous extract of compost samples induced a decreasing in the mitotic index and an increasing in the induction of chromosomal abnormalities. These results were statistically significant in relation to the negative control (distilled water). By comparing the results obtained for the nanocomposites in relative to pure polymer, there were no statistically significant differences. The types of the observed chromosomal aberrations indicated a possible genotoxic effect of the materials, which may be related to an aneugenic action of PLA degradation products.     

Rheology,Morphology and Thermal Properties of a PLA/PHB/Clay Blend Nanocomposite: The Influence of Process Parameters

Journal of Polymers and the Environment - The effect of process parameters on the final properties of a poly-lactic acid (PLA) and polyhydroxybutyrate (PHB) polymer blend filled with nanoclays was...     

Correlating pH and Swelling Degree Parameters to Understand the Sorption and Desorption Process of Diquat Herbicide from Nanocomposites Based on Polysaccharide and Clinoptilolite

Journal of Polymers and the Environment - Zeolite-based nanocomposites have become an efficient option for application in herbicide removal and controlled release systems. Our group previously...     

Effect of Casting Process Conditions on Mechanical Properties and Water Solubility of Films Made from Wolf Fruit and Its Optimization

Journal of Polymers and the Environment - Biodegradable films based on wolf fruit flour were prepared by the casting process using glycerol as a plasticizing agent. The influence that the process...