Prediction of some in situ tracer tests with sorbing tracers using independent data

Some recent converging tracer tests with sorbing tracers at the Asp? Hard Rock Laboratory in Sweden, the TRUE tests, have been predicted using only laboratory data and hydraulic data from borehole measurements. No model parameters were adjusted to obtain a better fit with the experiments. The independent data were fracture frequency and transmissivity data obtained in the field and laboratory data on sorption and matrix diffusion. Transmissivity measurements in five boreholes in the rock volume containing the region surrounding the injection and collection points show that there is a high frequency of water conducting fractures. Of 162 packed off sections with 0.5 m packer distances, 112 were found to have a transmissivity above the detection limit. The specific flow-wetted surface (FWS) of the rock mass could be estimated from these data. The transmissivities were found to be reasonably well described by a lognormal distribution. Laboratory data on diffusion and sorption properties together with the hydraulic data were used to "predict" the residence time distribution (RTD) of the sorbing tracers. The results were compared with the experimental breakthrough curves. In these experiments, the water residence time is very small compared to the residence time of the sorbing tracers due to their diffusion and sorption within the rock matrix. We thus could neglect the influence of the water residence time in our predictions. Therefore, no information on water residence times or on "dispersion" was needed. The dispersion of the sorbing tracers is caused by the different sorbing tracer residence times in different pathways. The sorbing tracer residence time is determined by the ratio of flowrate to the flow-wetted surface in the different pathways and not by the water residence time. Assuming a three-dimensional flow pattern and using the observed fracture frequency and flowrate distribution, breakthrough curves for three strongly sorbing tracers were predicted. Only the laboratory data, the transmissivity measurements and the pumping flowrate were used in the predictions. No information on the water residence time as obtained by the nonsorbing tracers was used. The predictions were surprisingly accurate.     

Modeling tracer diffusion in fractured and unfractured, unsaturated, porous media

A proposed tracer diffusion test for the Exploratory Shaft Facility at Yucca Mountain, NV, is modeled. For the proposed test, a solution containing conservative tracers will be introduced into a borehole in the geologic medium of interest. The tracers will diffuse and advect from the saturated source region into the unsaturated matrix in the surrounding tuff. After some time, the borehole is to be overcored, and tracer concentrations in the fluid will be measured in the core as a function of distance from emplacement. The data will be used to evaluate diffusive behavior and to derive effective diffusion coefficients for the tracers in the specific tuff. Numerical simulations are used to study the effects of effective diffusion coefficient, porosity, saturation, and fracturing on tracer transport. Results are reported for numerical simulations of tests in the Topopah Spring Member and the Tuff of Calico Hills, which have significantly different porosities and saturations. The simulations make the following predictions: The spread of tracer during the test will be sensitive to the effective diffusion coefficient of the tracer. Tracer will diffuse farther in the Topopah Spring Member than in the Tuff of Calico Hills because of the former's lower porosity and saturation. Tracer transport by advection into the Topopah Spring Member will be greater than that into the Tuff of Calico Hills because of capillary effects. While advection will be a significant mechanism for tracer penetration into the Topopah Spring tuff, it will be less significant for tracer penetration into the Calico Hills tuff. The proximity of a single vertical fracture to the source region determines its effects on tracer transport, especially if the fracture diverts fluid flowing from the source region into the matrix.     

Interpretation of injection-withdrawal tracer experiments conducted between two wells in a large single fracture

Tracer experiments conducted using a flow field established by injecting water into one borehole and withdrawing water from another are often used to establish connections and investigate dispersion in fractured rock. As a result of uncertainty in the uniqueness of existing models used for interpretation, this method has not been widely used to investigate more general transport processes including matrix diffusion or advective solute exchange between mobile and immobile zones of fluid. To explore the utility of the injection-withdrawal method as a general investigative tool and with the intent to resolve the transport processes in a discrete fracture, two tracer experiments were conducted using the injection-withdrawal configuration. The experiments were conducted in a fracture which has a large aperture (>500 microm) and horizontally pervades a dolostone formation. One experiment was conducted in the direction of the hydraulic gradient and the other in the direction opposite to the natural gradient. Two tracers having significantly different values of the free-water diffusion coefficient were used. To interpret the experiments, a hybrid numerical-analytical model was developed which accounts for the arcuate shape of the flow field, advection-dispersion in the fracture, diffusion into the matrix adjacent to the fracture, and the presence of natural flow in the fracture. The model was verified by comparison to a fully analytical solution and to a well-known finite-element model. Interpretation of the tracer experiments showed that when only one tracer, advection-dispersion, and matrix diffusion are considered, non-unique results were obtained. However, by using multiple tracers and by accounting for the presence of natural flow in the fracture, unique interpretations were obtained in which a single value of matrix porosity was estimated from the results of both experiments. The estimate of porosity agrees well with independent measurements of porosity obtained from core samples. This suggests that: (i) the injection-withdrawal method is a viable tool for the investigation of general transport processes provided all relevant experimental conditions are considered and multiple conservative tracers are used; and (ii) for the conditions of the experiments conducted in this study, the dominant mechanism for exchange of solute between the fracture and surrounding medium is matrix diffusion.     

Field investigation into unsaturated flow and transport in a fault: model analyses

Results of a fault test performed in the unsaturated zone of Yucca Mountain, Nevada, were analyzed using a three-dimensional numerical model. The fault was explicitly represented as a discrete feature and the surrounding rock was treated as a dual-continuum (fracture-matrix) system. Model calibration against seepage and water-travel-velocity data suggests that lithophysal cavities connected to fractures can considerably enhance the effective fracture porosity and therefore retard water flow in fractures. Comparisons between simulation results and tracer concentration data also indicate that matrix diffusion is an important mechanism for solute transport in unsaturated fractured rock. We found that an increased fault-matrix and fracture-matrix interface areas were needed to match the observed tracer data, which is consistent with previous studies. The study results suggest that the current site-scale model for the unsaturated zone of Yucca Mountain may underestimate radionuclide transport time within the unsaturated zone, because an increased fracture-matrix interface area and the increased effective fracture porosity arising from lithophysal cavities are not considered in the current site-scale model.     

In situ diffusion experiment in granite: phase I

A program of in situ experiments, supported by laboratory studies, was initiated to study diffusion in sparsely fractured rock (SFR), with a goal of developing an understanding of diffusion processes within intact crystalline rock. Phase I of the in situ diffusion experiment was started in 1996, with the purpose of developing a methodology for estimating diffusion parameter values. Four in situ diffusion experiments, using a conservative iodide tracer, were performed in highly stressed SFR at a depth of 450 m in the Underground Research Laboratory (URL). The experiments, performed over a 2 year period, yielded rock permeability estimates of 2 x 10(-21) m(2) and effective diffusion coefficients varying from 2.1 x 10(-14) to 1.9 x 10(-13) m(2)/s, which were estimated using the MOTIF code. The in situ diffusion profiles reveal a characteristic "dog leg" pattern, with iodide concentrations decreasing rapidly within a centimeter of the open borehole wall. It is hypothesized that this is an artifact of local stress redistribution and creation of a zone of increased constrictivity close to the borehole wall. A comparison of estimated in situ and laboratory diffusivities and permeabilities provides evidence that the physical properties of rock samples removed from high-stress regimes change. As a result of the lessons learnt during Phase I, a Phase II in situ program has been initiated to improve our general understanding of diffusion in SFR.     

The effects of matrix diffusion on radionuclide migration in rock column experiments

Rock column experiments were performed to examine the effects of matrix diffusion and hydrodynamic dispersion on the migration of radionuclides at the laboratory scale. Tritiated water and chloride transportation was studied in intact mica gneiss and in altered more porous tonalite columns with narrow flow channels. The column diffusion properties were estimated prior to water flow experiments using the gas diffusion method with helium as the tracer gas. The numerical compartment model for advection and dispersion, with and without matrix diffusion, was used to interpret the tracer transport in the columns. Matrix diffusion behavior was also distinguished from dominating hydrodynamic dispersion in rock column experiments at the slowest water flow rates.     

Radionuclide transport and retardation in rock fracture and crushed rock column experiments

Transport and retardation of non-sorbing tritiated water and chloride and slightly sorbing sodium was studied in Syyry area SY-KR7 mica gneiss, in altered porous tonalite and in fresh tonalite. Experiments were performed using dynamic fracture and crushed rock column methods. Static batch method for sodium was introduced to compare retardation values from static and dynamic experiments. The ¹⁴C-PMMA method was used to study the pore structure of matrices. The pore aperture distribution was evaluated from Hg-porosimetry determinations and the surface areas were determined using the B.E.T. method. The flow characteristics and transport behavior of tracers were interpreted using a numerical compartment model for dispersion. The effect of matrix diffusion was calculated using an analytical solution to the advection-matrix diffusion problem in which surface retardation was taken into account. Radionuclide transport behavior in rock fractures was explained on the basis of rock structure.     

A laboratory experiment for determining both the hydraulic and diffusive properties and the initial pore-water composition of an argillaceous rock sample: a test with the Opalinus clay (Mont Terri, Switzerland)

Argillaceous formations are thought to be suitable natural barriers to the release of radionuclides from a radioactive waste repository. However, the safety assessment of a waste repository hosted by an argillaceous rock requires knowledge of several properties of the host rock such as the hydraulic conductivity, diffusion properties and the pore water composition. This paper presents an experimental design that allows the determination of these three types of parameters on the same cylindrical rock sample. The reliability of this method was evaluated using a core sample from a well-investigated indurated argillaceous formation, the Opalinus Clay from the Mont Terri Underground Research Laboratory (URL) (Switzerland). In this test, deuterium- and oxygen-18-depleted water, bromide and caesium were injected as tracer pulses in a reservoir drilled in the centre of a cylindrical core sample. The evolution of these tracers was monitored by means of samplers included in a circulation circuit for a period of 204 days. Then, a hydraulic test (pulse-test type) was performed. Finally, the core sample was dismantled and analysed to determine tracer profiles. Diffusion parameters determined for the four tracers are consistent with those previously obtained from laboratory through-diffusion and in-situ diffusion experiments. The reconstructed initial pore-water composition (chloride and water stable-isotope concentrations) was also consistent with those previously reported. In addition, the hydraulic test led to an estimate of hydraulic conductivity in good agreement with that obtained from in-situ tests.     

Using constant head step tests to determine hydraulic apertures in fractured rock

The initial step in the analysis of contaminant transport in fractured rock requires the consideration of groundwater velocity. Practical methods for estimating the average linear groundwater velocity (vˉ) in fractured rock require determination of hydraulic apertures which are commonly calculated by applying the cubic law using transmissivity (T) values and the number of hydraulically active fractures in the test interval. High-resolution, constant-head step injection testing of cored boreholes in a 100 m thick fractured dolostone aquifer was conducted using inflatable packers to isolate specific test intervals from the rest of the borehole. The steps in each test interval were gradually increased from very low to much higher injection rates. At smaller injection rates, the flow rate vs. applied pressure graph projects through the origin and indicates Darcian flow; non Darcian flow is evident at higher injection rates. Non-Darcian flow results in significantly lower calculated T values, which translates to smaller hydraulic aperture values. Further error in the calculated hydraulic aperture stems from uncertainty in the number of hydraulically active fractures in each test interval. This estimate can be inferred from borehole image and core logs, however, all of the fractures identified are not necessarily hydraulically active. This study proposes a method based on Reynolds number calculations aimed at improving confidence in the selection of the number of active fractures in each test interval.     

The influence of mass transfer on solute transport in column experiments with an aggregated soil

The spreading of concentration fronts in dynamic column experiments conducted with a porous, aggregated soil is analyzed by means of a previously documented transport model (DFPSDM) that accounts for longitudinal dispersion, external mass transfer in the boundary layer surrounding the aggregate particles, and diffusion in the intra-aggregate pores. The data are drawn from a previous report on the transport of tritiated water, chloride, and calcium ion in a column filled with Ione soil having an average aggregate particle diameter of 0.34 cm, at pore water velocities from 3 to 143 cm/h. The parameters for dispersion, external mass transfer, and internal diffusion were predicted for the experimental conditions by means of generalized correlations, independent of the column data. The predicted degree of solute front-spreading agreed well with the experimental observations. Consistent with the aggregate porosity of 45%, the tortuosity factor for internal pore diffusion was approximately equal to 2. Quantitative criteria for the spreading influence of the three mechanisms are evaluated with respect to the column data. Hydrodynamic dispersion is thought to have governed the front shape in the experiments at low velocity, and internal pore diffusion is believed to have dominated at high velocity; the external mass transfer resistance played a minor role under all conditions. A transport model such as DFPSDM is useful for interpreting column data with regard to the mechanisms controlling concentration front dynamics, but care must be exercised to avoid confounding the effects of the relevant processes.     

A multi-directional tracer test in the fractured Chalk aquifer of E. Yorkshire, UK

A multi-borehole radial tracer test has been conducted in the confined Chalk aquifer of E. Yorkshire, UK. Three different tracer dyes were injected into three injection boreholes and a central borehole, 25 m from the injection boreholes, was pumped at 330 m(3)/d for 8 days. The breakthrough curves show that initial breakthrough and peak times were fairly similar for all dyes but that recoveries varied markedly from 9 to 57%. The breakthrough curves show a steep rise to a peak and long tail, typical of dual porosity aquifers. The breakthrough curves were simulated using a 1D dual porosity model. Model input parameters were constrained to acceptable ranges determined from estimations of matrix porosity and diffusion coefficient, fracture spacing, initial breakthrough times and bulk transmissivity of the aquifer. The model gave equivalent hydraulic apertures for fractures in the range 363-384 microm, dispersivities of 1 to 5 m and matrix block sizes of 6 to 9 cm. Modelling suggests that matrix block size is the primary controlling parameter for solute transport in the aquifer, particularly for recovery. The observed breakthrough curves suggest results from single injection-borehole tracer tests in the Chalk may give initial breakthrough and peak times reasonably representative of the aquifer but that recovery is highly variable and sensitive to injection and abstraction borehole location. Consideration of aquifer heterogeneity suggests that high recoveries may be indicative of a high flow pathway adjacent, but not necessarily connected, to the injection and abstraction boreholes whereas low recoveries may indicate more distributed flow through many fractures of similar aperture.     

Field tracer-transport tests in unsaturated fractured tuff.

This paper presents the results of a field investigation in the unsaturated, fractured welded tuff within the Exploratory Studies Facility (ESF) at Yucca Mountain, NV. This investigation included a series of tests during which tracer-laced water was released into a high-permeability zone within a horizontal injection borehole. The tracer concentration was monitored in the seepage collected in an excavated slot about 1.6 m below the borehole. Results showed significant variability in the hydrologic response of fractures and the matrix. Analyses of the breakthrough curves suggest that flow and transport pathways are dynamic, rather than fixed, and related to liquid-release rates. Under high release rates, fractures acted as the predominant flow pathways, with limited fracture-matrix interaction. Under low release rates, fracture flow was comparatively less dominant, with a noticeable contribution from matrix flow. Observations of tracer concentrations rebounding in seepage water, following an interruption of flow, provided evidence of mass exchange between the fast-flowing fractures and slow- or non-flowing regions. The tests also showed the applicability of fluorinated benzoate tracers in situations where multiple tracers of similar physical properties are warranted.     

Diffusion of tritiated water and 22Na+ through non-degraded hardened cement pastes

Diffusion experiments through hardened cement pastes (HCP) using tritiated water (HTO) and 22Na(+), considered to be conservative tracers, have been carried out in triplicates in a glove box under a controlled nitrogen atmosphere. Each experiment consisted of a through-diffusion test followed by an out-diffusion test. The experimental data were inversely modelled applying an automated Marquardt-Levenberg procedure. The analysis of the through-diffusion data allowed the extraction of values for the effective diffusion coefficients, D(e), and the rock capacity factor, alpha. Good agreement between measured and calculated tracer breakthrough curves was achieved using both a simple diffusion model without sorption and a diffusion/linear sorption model. The best-fit K(d)-values were found to be consistent with R(d)-values measured in previous batch-sorption experiments. The best-fit values from the through-diffusion tests were then used to predict the results of subsequent out-diffusion experiments. Good agreement between experimental data and predictions was achieved only for the case of linear sorption. Isotopic exchange can only partially account for both the amount of tracer taken up in the batch-sorption tests and the measured retardation in the diffusion experiments and, hence, additional mechanisms have to be invoked to explain the data.     

An axisymmetric diffusion experiment for the determination of diffusion and sorption coefficients of rock samples

Diffusion anisotropy is a critical property in predicting migration of substances in sedimentary formations with very low permeability. The diffusion anisotropy of sedimentary rocks has been evaluated mainly from laboratory diffusion experiments, in which the directional diffusivities are separately estimated by through-diffusion experiments using different rock samples, or concurrently by in-diffusion experiments in which only the tracer profile in a rock block is measured. To estimate the diffusion anisotropy from a single rock sample, this study proposes an axisymmetric diffusion test, in which tracer diffuses between a cylindrical rock sample and a surrounding solution reservoir. The tracer diffusion between the sample and reservoir can be monitored from the reservoir tracer concentrations, and the tracer profile could also be obtained after dismantling the sample. Semi-analytical solutions are derived for tracer concentrations in both the reservoir and sample, accounting for an anisotropic diffusion tensor of rank two as well as the dilution effects from sampling and replacement of reservoir solution. The transient and steady-state analyses were examined experimentally and numerically for different experimental configurations, but without the need for tracer profiling. These experimental configurations are tested for in- and out-diffusion experiments using Koetoi and Wakkanai mudstones and Shirahama sandstone, and are scrutinized by a numerical approach to identify favorable conditions for parameter estimation. The analysis reveals the difficulty in estimating diffusion anisotropy; test configurations are proposed for enhanced identifiability of diffusion anisotropy. Moreover, it is demonstrated that the axisymmetric diffusion test is efficient in obtaining the sorption parameter from both steady-state and transient data, and in determining the effective diffusion coefficient if isotropic diffusion is assumed. Moreover, measuring reservoir concentrations in an axisymmetric diffusion experiment coupled with tracer profiling may be a promising approach to estimate of diffusion anisotropy of sedimentary rocks.     

Matrix diffusion coefficients in volcanic rocks at the Nevada test site: influence of matrix porosity, matrix permeability, and fracture coating minerals

Diffusion cell experiments were conducted to measure nonsorbing solute matrix diffusion coefficients in forty-seven different volcanic rock matrix samples from eight different locations (with multiple depth intervals represented at several locations) at the Nevada Test Site. The solutes used in the experiments included bromide, iodide, pentafluorobenzoate (PFBA), and tritiated water ((3)HHO). The porosity and saturated permeability of most of the diffusion cell samples were measured to evaluate the correlation of these two variables with tracer matrix diffusion coefficients divided by the free-water diffusion coefficient (D(m)/D*). To investigate the influence of fracture coating minerals on matrix diffusion, ten of the diffusion cells represented paired samples from the same depth interval in which one sample contained a fracture surface with mineral coatings and the other sample consisted of only pure matrix. The log of (D(m)/D*) was found to be positively correlated with both the matrix porosity and the log of matrix permeability. A multiple linear regression analysis indicated that both parameters contributed significantly to the regression at the 95% confidence level. However, the log of the matrix diffusion coefficient was more highly-correlated with the log of matrix permeability than with matrix porosity, which suggests that matrix diffusion coefficients, like matrix permeabilities, have a greater dependence on the interconnectedness of matrix porosity than on the matrix porosity itself. The regression equation for the volcanic rocks was found to provide satisfactory predictions of log(D(m)/D*) for other types of rocks with similar ranges of matrix porosity and permeability as the volcanic rocks, but it did a poorer job predicting log(D(m)/D*) for rocks with lower porosities and/or permeabilities. The presence of mineral coatings on fracture walls did not appear to have a significant effect on matrix diffusion in the ten paired diffusion cell experiments.     

Tracer test at El Berrocal site

Tracer tests provide highly valuable information about the transport properties of saturated rocks which is essential to the characterization of a potential radioactive waste repository site. In the frame of El Berrocal project, a set of tracer tests was performed in a complex geometry of inclined boreholes, combined with highly fractured transmissive zones. The aims of the tracer test programme were to gain experience, knowledge and insight into field transport experiments. To achieve this a detailed programme of new instrumentation design, site characterization and laboratory tasks was developed. For field monitoring a new electronic system was developed. The system is able to measure up to 256 parameters per borehole, with surface equipment to control pumping rates and physical and chemical parameters at both injection and extraction boreholes. The experiments progressed from single borehole dilution tests under both natural flow and forced gradient conditions to convergent flow tracer tests. Dilution tests helped to discriminate the most suitable borehole sections at which to inject tracers. The tracers were selected by the results of the laboratory programme. Uranine (fluorescein), DTPA-gadolinium (diethylenetriaminopentacetic acid, gadolinium (III)), and deuterium were injected simultaneously in one borehole section and recovered at another borehole 20 m away, pumping at a flowrate of 0.1 1 min⁻¹. First results showed a thickness porosity of 1.2 × 10⁻³ m and a longitudinal dispersivity of 17.0 m using uranine data acquired over a period of 4 d, at which point the recovery concentration had reached a maximum. However, gadolinium and deuterium appeared to travel faster, arriving at peak values after only 2 d of injection.     

Tracer diffusion coefficients in sedimentary rocks: correlation to porosity and hydraulic conductivity

Matrix diffusion is an important transport process in geologic materials of low hydraulic conductivity. For predicting the fate and transport of contaminants, a detailed understanding of the diffusion processes in natural porous media is essential. In this study, diffusive tracer transport (iodide) was investigated in a variety of geologically different limestone and sandstone rocks. Porosity, structural and mineralogical composition, hydraulic conductivity, and other rock properties were determined. The effective diffusion coefficients were measured using the time-lag method. The results of the diffusion experiments indicate that there is a close relationship between total porosity and the effective diffusion coefficient of a rock (analogous to Archie's Law). Consequently, the tortousity factor can be expressed as a function of total porosity. The relationship fits best for thicker samples (> 1.0 cm) with high porosities (> 20%), because of the reduced influence of heterogeneity in larger samples. In general, these correlations appear to be a simple way to determine tortuosity and the effective diffusion coefficient from easy to determine rock porosity values.     

Analysis of the migration of instantaneously injected cesium in artificial fractures of Lac du Bonnet granite, Manitoba, Canada

Breakthrough curves of ¹³⁷Cs and tritiated water injected instantaneously into artificial fractures in Lac du Bonnet granite were analyzed using the analytical solution for a single rock-fracture system and assuming the linear sorption isotherm of the solute. Parameters of nuclide diffusion and sorption in rock matrices, obtained by fitting, varied depending on the flow velocity in the fractures. According to theoretical calculations, different fracture flow velocities lead to different diffusion distances of nuclides in matrices at the same injection volume. As microscopic inhomogeneity is considered to exist in the rock matrix, the average diffusion-sorption characteristics of the matrix within the diffusion distance may have varied with the fracture flow velocity. Surface sorption was marked in fractures that had relatively high matrix sorption-diffusion capacities. The phenomenon was interpreted using the theoretical relationships developed between the surface sorption, matrix sorption and pore diffusion coefficient, and the porosity of matrices.The effect of the nonlinear sorption of solute was examined by numerically solving model equations that incorporate the nonlinear isotherm. This incorporation may contribute to the reduction of deviations between theoretical and experimental BTC's.     

Field-scale effective matrix diffusion coefficient for fractured rock: results from literature survey

Matrix diffusion is an important mechanism for solute transport in fractured rock. We recently conducted a literature survey on the effective matrix diffusion coefficient, D_m^e, a key parameter for describing matrix diffusion processes at the field scale. Forty field tracer tests at 15 fractured geologic sites were surveyed and selected for the study, based on data availability and quality. Field-scale D_m^e values were calculated, either directly using data reported in the literature, or by reanalyzing the corresponding field tracer tests. The reanalysis was conducted for the selected tracer tests using analytic or semi-analytic solutions for tracer transport in linear, radial, or interwell flow fields. Surveyed data show that the scale factor of the effective matrix diffusion coefficient (defined as the ratio of D_m^e to the lab-scale matrix diffusion coefficient, D_m, of the same tracer) is generally larger than one, indicating that the effective matrix diffusion coefficient in the field is comparatively larger than the matrix diffusion coefficient at the rock-core scale. This larger value can be attributed to the many mass-transfer processes at different scales in naturally heterogeneous, fractured rock systems.Furthermore, we observed a moderate, on average trend toward systematic increase in the scale factor with observation scale. This trend suggests that the effective matrix diffusion coefficient is likely to be statistically scale-dependent. The scale-factor value ranges from 0.5 to 884 for observation scales from 5 to 2000 m. At a given scale, the scale factor varies by two orders of magnitude, reflecting the influence of differing degrees of fractured rock heterogeneity at different geologic sites. In addition, the surveyed data indicate that field-scale longitudinal dispersivity generally increases with observation scale, which is consistent with previous studies. The scale-dependent field-scale matrix diffusion coefficient (and dispersivity) may have significant implications for assessing long-term, large-scale radionuclide and contaminant transport events in fractured rock, both for nuclear waste disposal and contaminant remediation.     

Evaluation of tritiated water diffusion through the Toarcian clayey formation of the Tournemire experimental site (France)

Through-diffusion experiments with tritiated water were performed on argillaceous samples from various zones of the Tournemire test site. It was intended to evaluate the homogeneity of the transport property of unfracturated samples and the influence of the orientation and the nature of the samples (presence of an opened fracture or a pre-existing tectonic fracture filled with calcite and pyrite). Homogeneous values of the tritiated water (HTO) effective diffusion coefficients were deduced from experiments carried out when diffusion occurred parallel to the stratigraphic bedding, with an apparent sensitivity to experimental conditions. Anisotropy was significant, De(HTO) perpendicular to the bedding being 1/3 lower than that parallel to the bedding. The observed fractures of the samples created by mechanical stress and partial dehydration during sawing and the presence of a pre-existing opened fracture did not affect the effective diffusion coefficients of tritiated water, which is probably due to the healing ability of the clayey medium during the re-saturation phases of the equilibrium steps performed prior to the diffusion experiments. On the contrary, a significant decrease of this transport parameter was induced by the occurrence of a pre-existing tectonic fracture, which was assigned to the dense structure of the filling phases.