Anaerobic Biodegradation of Blends Based on Polyvinyl Alcohol

The presented work deals with blends composed of polyvinyl alcohol (PVA) and biopolymers (protein hydrolysate, starch, lignin). PVA does not belong to biologically inert plastics but its degradation rate (particularly under anaerobic conditions) is low. A potential solution to the issue problem lies in preparation of blends with readily degradable substrates. We studied degradation of blow-molded films made of commercial PVA and mentioned biopolymers in an aqueous anaerobic environment employing inoculation with digested activated sludge from the municipal wastewater treatment plant. Films prepared in the first experimental series were to be used for comparing biodegradation of blends modified with native or plasticized starch; in this case effect of plasticization was not proved. The degree of PVA degradation after modification with native or plasticized starch increases in a striking and practically same manner already at a starch level as low as approximately 5 wt.%. Films of the second experimental series were prepared as additionally modified with protein hydrolysate and lignin. Only lignin-modified samples exhibited a somewhat lower degree of biodegradation but regarding the measure of lignin present in blend this circumstance is not essential. Level of biodegradation with all discussed films differed only slightly—within range of experimental error.     

Effect of Coconut, Sisal and Jute Fibers on the Properties of Starch/Gluten/Glycerol Matrix

Coconut, sisal and jute fibers were added as reinforcement materials in a biodegradable polymer matrix comprised of starch/gluten/glycerol. The content of fibers used in the composites varied from 5% to 30% by weight of the total polymers (starch and gluten). Materials were processed in a Haake torque rheometer (120 °C, 50 rpm) for 6 min. The mixtures obtained were molded by heat compression and further characterized. Addition of lignocellulosic fibers in the matrix decreased the water absorption at equilibrium. The diffusion coefficient decreased sharply around 5% fiber concentration, and further fiber additions caused only small variations. The thermogravimetric (TG) analysis revealed improved thermal stability of matrix upon addition of fibers. The Young’s modulus and ultimate tensile strength increased with fiber content in the matrix. The storage modulus increased with increasing fiber content, whereas tanδ curves decreased, confirming the reinforcing effect of the fibers. Morphology of the composites analyzed under the scanning electron microscope (SEM) exhibited good interfacial adhesion between the matrix and the added fibers. Matrix degraded rapidly in compost, and addition of increased amounts of coconut fiber in the matrix caused a slowdown the biodegradability of the matrix. Names are necessary to report factually on available data; however, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the product to the exclusion of others that may be suitable.     

Potential of <Emphasis Type="Italic">pinhão</Emphasis> Coat as Constituents of Starch Based Films Using Modification Techniques

The potential of lignocellulosic fibers obtained by dry grinding of pinhão coat as fillers in starch filmogenic solutions for packaging applications was evaluated in this work. To improve the incorporation of this waste into the starch solutions different physical and chemical treatments were conducted. Thereafter, morphology, chemical structure, crystallinity and water absorption of the pinhão coat powders were determined. The composites were also characterized regarding their morphology, chemical structure, crystallinity, mechanical properties, water vapor permeability and hydrophilicity. Poor fiber/matrix adhesion and high water absorption of the fibers were evidenced. Consequently, water vapor permeability of composites was increased by incorporating the fibers. Moreover, mechanical properties were improved and the morphological results were used to support the water absorption differences among the powders. Regarding the food packaging applications, starch/pinhão coat composites appeared as promising materials to reach the requirements of respiring food products.     

Preparation and Optimization of Starch/Poly Vinyl Alcohol/ZnO Nanocomposite Films Applicable for Food Packaging

Pollution and destruction of the environment due to the accumulation of non-degradable plastics are some of the most important concerns in the world. A significant amount of this waste is related to the polymers used in food packaging. Therefore, experts in the food industry have been looking for suitable biodegradable alternatives to synthetic polymers. Preparing biocompatible and biodegradable films based on starch is a good choice. In this study, various factors affecting films of starch/polyvinyl alcohol (PVA)/containing ZnO nanoparticles such as the amount of starch, PVA, glycerol, and ZnO were evaluated by response surface methodology (RSM). Film formation by solvent casting method, mechanical properties, swelling, solubility, and water vapor permeability (WVP) were selected as responses of RSM. The results showed that hydrogen bonding interactions between polyvinyl alcohol and starch improved the film formation. The effect of glycerol and PVA content on the mechanical strength was contrary to each other. As the amount of PVA increased, the tensile strength first decreased and then increased. The value of WVP was for all Runs from 0 to 6.77?×?10^??8 g m^??1 s^??1 Pa^??1. Finally, films with high film formation, maximum tensile strength, and high elongation at break, minimum solubility, permeability, and swelling were optimized.

     

Preparation and Characterization of Gamma Irradiated Sugar Containing Starch/Poly (Vinyl Alcohol)-Based Blend Films

Blends based on different ratios of starch (35–20%) and plasticizer (sugar; 0–15%) keeping the amount of poly(vinyl alcohol) (PVA) constant, were prepared in the form of thin films by casting solutions. The effects of gamma-irradiation on thermal, mechanical, and morphological properties were investigated. The studies of mechanical properties showed improved tensile strength (TS) (9.61 MPa) and elongation at break (EB) (409%) of the starch-PVA-sugar blend film containing 10% sugar. The mechanical testing of the irradiated film (irradiated at 200 Krad radiation dose) showed higher TS but lower EB than that of the non-radiated film. FTIR spectroscopy studies supported the molecular interactions among starch, PVA, and sugar in the blend films, that was improved by irradiation. Thermal properties of the film were also improved due to irradiation and confirmed by thermo-mechanical analysis (TMA), differential thermo-gravimetric analysis (DTG), differential thermal analysis (DTA), and thermo-gravimetric analysis (TGA). Surface of the films were examined by scanning electron microscope (SEM) image that supported the evidence of crosslinking obtained after gamma irradiation on the film. The water up-take and degradation test in soil of the film were also evaluated. In this study, sugar acted as a good plasticizing agent in starch/PVA blend films, which was significantly improved by gamma radiation and the prepared starch-PVA-sugar blend film could be used as biodegradable packaging materials.     

Effect of Manufacturing Process and Xanthan Gum Addition on the Properties of Cassava Starch Films

The objective of this work was to manufacture biodegradable films by two different processes (casting and extrusion), from different combinations of cassava starch and xanthan gum. These films were produced by casting and by extrusion from six different starch-xanthan gum combinations (0, 2, 4, 6, 8 and 10% w/w), containing glycerol as plasticizer (20% w/w) and were also characterized according to their microstructure, optical, mechanical, and barrier properties. Scanning electron microscopy of the starch-xanthan gum extruded films showed reticulated surface and smooth interior, suggesting that xanthan was driven to the surface and gelatinized starch to the interior of the films during extrusion. Films manufactured by casting were entirely homogeneous. In general, casted films presented lower opacity and water vapor permeability and higher stress at break than films manufactured by extrusion. Xanthan gum addition affected mechanical properties of starch films, improving their stress and strain at break, especially for extruded samples, but these properties did not show stability at different RH conditions.     

Role of Crosslinker on the Biodegradation Behavior of Starch/Polyvinylalcohol Blend Films

The effect of crosslinkers on the biodegradation behavior of starch/polyvinyl alcohol (PVA) blend films was investigated by weight loss study, Scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). Starch/PVA films were prepared by solution casting method and 5 weight% of four different crosslinking agents like epichlorohydrin, formaldehyde, zinc oxide and borax were used in four different sets to crosslink the films. These crosslinked starch/PVA films were biodegraded in compost. Weight loss study showed that crosslinking retarded the biodegradation of the films in the first 15?days, but after that, there was a significant increase in weight loss. The DSC analysis revealed that the consumption of starch and consequent rearrangement of the PVA molecules were distinctly different in the crosslinked films due to the effect of different crosslinking agents.     

Properties of Starch/PVA Blend Films Containing Citric Acid as Additive

Starch/polyvinyl alcohol (PVA) blend films were prepared successfully by using starch, polyvinyl alcohol (PVA), glycerol (GL) sorbitol (SO) and citric acid (CA) for the mixing process. The influence of mixing time, additional materials and drying temperature of films on the properties of the films was investigated. With increase in mixing time, the tensile strength (TS), elongation (%E), degree of swelling (DS) and solubility (S) of the film were equilibrated. The equilibrium for TS, %E, DS and S value was 20.12 MPa, 36.98%, 2.4 and 0.19, respectively. The mixing time of equilibrium was 50 min. TS, %E, DS and S of starch/PVA blend film were examined adding glycerol (GL), sorbitol (SO) and citric acid (CA) as additives. At all measurement results, except for DS, the film adding CA was better than GL or SO because hydrogen bonding at the presence of CA with hydroxyl group and carboxyl group increased the inter/intramolecular interaction between starch, PVA and additives. Citric acid improves the properties of starch/PVA blend film compared to glycerol and sobitol. When the film was dried at low temperature, the properties of the films were clearly improved because the hydrogen bonding was activated at low temperature.     

The influence of soil macroinvertebrates on primary biodegradation of starch-containing polyethylene films

The primary biodegradability of polyethylene (PE) films containing different percentages of cornstarch (0–50%) and other additives (prooxidant, oxidized polyethylene) was tested using four species of earthworms (Eisenia fetida, Lumbricus terrestris, Aporectodea trapezoides, Aporectodea tuberculata), three species of cockroaches (Periplaneta americana, Blaberus sp.,Blattella germanica), termites (Reticulotermes flavipes), sowbugs (Porcellio laevis), and crickets (Acheta domesticus). These studies were conducted to elucidate the potential role of soil macroinvertebrates in degrading starch/PE biodegradable plastics. The results of the macroinvertebrate bioassays indicate that crickets, cockroaches, and sowbugs consumed starch-containing PE films most readily. In addition, the degree to which the films were attacked and consumed was directly related to the starch content of the film. Films with oxidized polyethylene and those containing prooxidant (vegetable oil and a transition metal catalyst) were also consumed. None of the four species of earthworms tested or the termites showed any activity toward the starch/polyethylene films. These results have important implications for determining the fate of novel plastic formulations which claim to be biodegradable in natural environments. Studies such as these, coupled with studies on microbial degradation, will help provide the type of information needed to assess the environmental fate of biodegradable starch/PE plastics and fill the voids in the scientific database regarding this rapidly developing field.     

Influence of Fibers on the Mechanical Properties of Cassava Starch Foams

The utilization of renewable resources in packaging can provide solutions to ecological problems such as waste quantity. Agricultural resources are alternative raw materials, among which there is starch, a natural polysaccharide that can be used to form resistant foam under wet and warm conditions. The starch foam is obtained by thermo pressing process where cassava starch, water and additives are processed to form a rigid structure by swelling, gelatinization and network formation. Natural fibers can be used to improve the mechanical properties of starch foams. In this project was investigated the influence of the addition of fibers in the levels of 1, 2 and 3% of cassava (short fiber) and 1, 2 and 3% of wheat fiber (powered fiber) in the starch dough. The foams were characterized by physical methods of strength, flexibility, density and by Scanning Electron Microscopy (SEM). The increase in fibers quantity has resulted in foams with higher density and less flexibility, whatever the fiber type. Most fibers quantity did not improve the foam strength. Foam made with 1% of cassava fiber showed higher compression strength; by increasing the percentage quantity there was a decrease on the compression resistance. Foam made with wheat fiber presented a lower result in 2%. The fiber type had no statistical significance in strength, flexibility and density foam. Only the fiber quantity was significant. The results showed that both fibers presented limited dimensions to improve the reinforcement of the starch foams up to 1%.     

Effect of Cotton Fiber Contents and Lengths on Properties of Thermoplastic Starch Composites Prepared from Rice and Waxy Rice Starches

Biodegradable polymer was prepared as thermoplastic starch (TPS) using rice and waxy rice starches. In order to increase mechanical properties and reduce water absorption of the TPS, cotton fiber was incorporated as the fiber reinforcement into the TPS matrix. The effect of cotton fiber contents and lengths on properties of the TPS was examined. Internal mixer and compression molding machine were used to mix and shape the samples. It was found that the thermoplastic rice starch (TPRS) showed higher stress at maximum load and Young’s modulus but lower strain at maximum load than the thermoplastic waxy rice starch (TPWRS). In addition, stress at maximum load and Young’s modulus of both TPRS and TPWRS increased significantly with the addition of the cotton fiber. Cotton fiber contents and lengths also affected mechanical properties of the TPRS and TPWRS composites. Moreover, water absorption of the TPRS and TPWRS composites decreased by the use of the cotton fibers. FT-IR and XRD techniques were used to study a change in functional group and crystallinity of the thermoplastic starch composites. Morphological, thermal and biodegradable properties of different thermoplastic starch composites were also investigated.     

TPS/PCL Composite Reinforced with Treated Sisal Fibers: Property, Biodegradation and Water-Absorption

Sisal fibers bleached with sodium-hydroxide followed by hydrogen peroxide treatment were incorporated in a thermoplastic starch/ε-polycaprolactone (TPS/PCL) blend via extrusion processing. These samples with smooth and homogenous surfaces were examined for their property, biodegradability and water absorption. Scanning electron microscopy revealed that the fibers were well dispersed in the matrix. In addition, it was found that the fibers and matrices interacted strongly. Blends with 20 % (dry weight-basis) fiber content showed some fiber agglomeration. Whereas blends with 10 % fibers showed increased crystallinity and lower water absorption capacity. The CO₂ evolution study showed that the thermoplastic starch samples without any additives had the highest rate and extent of degradation whereas the neat PCL samples had the lowest degradation rate. Addition of fiber to the TPS/PCL blend exhibited the degradation rates and extents that were somewhere in between the pure TPS and neat PCL. This work demonstrates that TPS/PCL composites reinforced with bleached sisal has superior structural characteristics and water resistance and thus, can be used as polymeric engineering composites for different applications.     

Physical Properties, Photo- and Bio-degradation of Baked Foams Based on Cassava Starch, Sugarcane Bagasse Fibers and Montmorillonite

The objectives of this work were to develop biodegradable trays from cassava starch, sugarcane fibers and Na-montmorillonite (Na-MMT) using a baking process and to study the effects of these components on the physical properties, photo- and bio-degradation of the trays. The sample F20 (produced with 20 g fiber/100 g formulation) showed the maximum yield production (100 %). All formulations resulted in well-shaped trays with densities between 0.1941 and 0.2966 g/cm³. The addition of fibers and Na-MMT resulted in less dense and less rigid trays compared to control samples (only starch). The studied processing conditions resulted in good nanoclay dispersion, leading to the formation of an exfoliated structure. The evaluation of the photo-degradation stability of the trays under UV exposure for 336 h showed that a sample produced with a specific combination of fiber and nanoclay (20 g fiber and 5 g nanoclay/100 g formulation) had the highest loss in stress at break (91 %). Biodegradation assays showed that Control trays (starch) and F20 (20 g fiber/100 g formulation) lost a greater percentage of their weight after 90 days of incubation in soil, with losses of up to 85.50 and 82.70 %, respectively.     

Biodegradability of Starch Based Self-Supporting Antimicrobial Film and Its Effect on Soil Quality

Alarming environmental pollution from petroleum based non-biodegradable disposable packaging films has generated concern for development of alternatives from natural polymers such as starch. In the present work, the biodegradability of a self-supporting film made from starch and polyvinyl alcohol (PVA) (starch:PVA?=?9:1 as the polymer) together with glutaraldehyde as crosslinker and sodium propionate (SP) as antimicrobial was investigated by soil burial method. The changes in soil composition namely pH, organic carbon, available and total nitrogen, and water holding capacity as a result of biodegradation were also estimated. The film underwent ≈?90% biodegradation within a period of 28 days, with simultaneous increase in soil nutrients. Moreover, the pH remained in the accepted limit for plant growth. Thus, antimicrobial in the film did not hamper its biodegradation, rather disposal of the film in soil might facilitate plant growth.     

Physical Properties of Chemically Modified Starch(RS4)/PVA Blend Films—Part 1

In this paper, we report on the physical properties of films that have been synthesized by using native corn starch (NS) and chemically modified starch (RS4). NS or RS4/PVA blend films were synthesized by using the mixing process and the casting method. Glycerol (GL), sorbitol (SO), and citric acid (CA) were used as additives. The chemically modified starch (RS4) was synthesized by using sodium trimetaphosphate (STMP) and sodium tripolyphosphate (STPP) as a crosslinker. Then, the RS4 thus synthesized was confirmed by using the pancreatin-gravimetric method, swelling power and an X-ray diffractometer (XRD). Tensile strength (TS), elongation (%E), swelling behavior (SB), and solubility (S) of the films were measured. The result of the measurements indicated the RS4-added film was better than the NS-added film. Especially, the RS4/PVA blend film with CA as an additive showed the physical properties superior to other films.     

Characterization of Urea Encapsulated by Biodegradable Starch-PVA-Glycerol

The influence of the blending ratio of biodegradable starch/polyvinyl alcohol (PVA)/glycerol in encapsulating urea has been investigated. It is found that water absorption capacity increased approximately 135 % as the amounts of starch, PVA and glycerol in the composite film increase. Therefore, the swell ability of the composite film is increased and the urea is released from the composite film in the wet environment. The FTIR shows that the urea had been encapsulated successfully in the composite films. Moreover, the soil burial biodegradation results indicated that the biodegradability of the starch/PVA/glycerol/urea composite film strongly depended on the PVA proportion in the composite film matrix. The DSC results show that the higher the amount of PVA in the composite film, the less change of the melting enthalpy value. The crystalline region of PVA remains after biodegradation.     

Evaluation of the Biodegradability of Polyvinyl Alcohol/Starch Blends: A Methodological Comparison of Environmentally Friendly Materials

Polyvinyl alcohol (PVA) and starch are both biodegradable polymers. These two polymers can be prepared as biodegradable plastics that are emerging as one of the environmental friendly materials available now. In this study, after reacting with sodium trimetaphosphate (STMP), modified corn starch was blended with PVA in different ratios by a barbender. Test samples were prepared for mechanical and thermal properties measurements. The surface roughness and morphology of fractured surface of the samples were observed by an atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements. Aqueous degradation by enzyme, water absorption and biodegradability behavior were evaluated for the degradability. The biodegradability of these materials was followed by bio-reactivity kinetics models. Results showed that the addition of modified starch could enhance its water uptake. With an addition of 20 wt% of modified starch, the blend had a maximum weight loss during enzymatic degradation. It was found that the degradability was enhanced with the addition of the starch. Analyzing the results of the biodegradability based on the kinetic models, the growth rate of the microorganism was found to be increasing with the increase of the content of starch in the PVA/starch blends in the first order reaction fashion. In our biodegradability analysis, i.e., based on the China national standards (CNS) 14432 regulations, we estimated the decomposition behavior based on the mentioned first order reaction. We found that the PVA/starch blends would take 32.47, 16.20 and 12.47 years to degrade by 70% as their starch content 0, 20 and 40 wt%, respectively.     

Interactive Influence of Biofiber Composition and Elastomer on Physico-Mechanical Properties of PLA Green Composites

The objective of this work was to improve the impact and thermal properties of polylactic acid (PLA)-based biocomposite by appropriate application of cellulosic fiber and a bioelastomer. Biocomposites formulations with fiber contents of up to 20% in combination with a bioelastomer were extrusion-compounded in a twin-screw extruder followed by molding in an injection molding system. Fibers used in the formulations included three types of cellulosic fiber; namely, raw fiber from oat hull biomass (RF), hydrolysis byproduct (ATF) which was the solid fraction obtained from an acid-catalyzed hydrolysis of RF, and delignified fibers (AD30, AD65, AD100) which were the products of delignification of ATF. Formulated biocomposites were characterized for thermal (glass transition and melting temperatures, and enthalpy of melting) and physico-mechanical (tensile and bending strengths, stiffness, impact energy, and water absorption) properties. Among all types of biofibers, RF resulted in poor properties in the biocomposites due to the high hemicellulose content in the structure. On the other hand, the ratio of lignin to cellulose (in the absence of hemicellulose) in the modified fibers did not significantly affect the physico-mechanical and thermal properties of the biocomposites. The elastomer applied in the formulations improved the impact energy, thermal properties, and elongation at break of the composites. However, it adversely affected the strength and water resistance of biocomposites, especially in the presence of hemicellulose. The results indicated that, depending on the application, a wide range of PLA green composites with different physico-mechanical properties can be achieved.     

Mechanical Property and Biodegradability of Cast Films Prepared from Blends of Oppositely Charged Biopolymers

Biodegradable cast films of about 50 m thickness were fabricated by blending oppositely charged biopolymers such as anionic starch–chitosan, and cationic starch–pectin. The tensile strength and elongation at break (%) of films were evaluated as well as their capacity to degrade in compost. Films recovered from soil every 48 h showed consistent degradation (weight loss), diminution of the polymers characteristic peak absorbance in the carbohydrate fingerprint region of the FTIR, and changes in the surface morphology via scanning electron microscopy (SEM). Anionic starch–chitosan films had much superior tensile strength and elongation compared to cationic starch–pectin, suggesting that the ionic bonds formed between anionic-starch and positively charged groups in chitosan polymer were much more stable and stronger. Initially, both films lost about 36% weight within 96 h, which also correlated well with the loss in the characteristic absorption peaks in the region of the infrared spectrum typical of biopolymers. The total mineralization of films by microorganisms in compost soil was also measured using respirometric techniques. Though the rate of mineralization differed for two formulations, total mineralization (extent) for both films were achieved within 45 days.