On the effect of MSW moisture content on meeting target recycling rates

A mathematical model to calculate the recycle rates for packaging materials from the municipal solid wastes (MSW) built from the dry mass values that are obtained from the corresponding wet masses and their respective moisture contents is presented in this work. A possible universal methodology is also described to be used with the previous model so that reliable comparisons between indicators for different regions are feasible. Furthermore, this mathematical model demonstrates the effect of the moisture content of packaging materials on their recycling rates and constitutes a fundamental tool for operators and persons responsible for MSW management to define new policies and technical measures viewing the improvement of recycling rates. A theoretical study and the application of the model to the MEMSW of the Lisbon region shows that the moisture content of the mixed wastes plays a dominant role in the recycling rates of packaging materials such as paper, plastics and glass. Moreover, accounting for all relevant masses in the dry basis yields higher recycling rate values: increases of 32.8% for paper, 50% for plastics and 44.6% glass are observed.     

A flexible environmental reuse/recycle policy based on economic strength

Environmental policies based on fixed recycling rates may lead to increased environmental impacts (e.g., landfilled wastes) during economic expansion. A rate policy is proposed, which is adjusted according to the overall strength or weakness of the economy, as reflected by overall packaging demand and consumption, production and imports-exports. During economic expansion featuring rising consumption, production or exports, the proposed flexible policy suggests a higher reuse/recycle rate. During economic slowdown a lower rate results in lower impacts. The flexible target rates are determined in terms of annual data, including consumption, imports-exports and production. Higher environmental gains can be achieved at lower cost if the flexible policy is applied to widely consumed packaging products and materials associated with low rates, or if cleaner recycling technology is adopted.     

Rapid discrimination of plastic packaging materials using MIR spectroscopy coupled with independent components analysis (ICA)

Plastic packaging wastes increased considerably in recent decades, raising a major and serious public concern on political, economical and environmental levels. Dealing with this kind of problems is generally done by landfilling and energy recovery. However, these two methods are becoming more and more expensive, hazardous to the public health and the environment. Therefore, recycling is gaining worldwide consideration as a solution to decrease the growing volume of plastic packaging wastes and simultaneously reduce the consumption of oil required to produce virgin resin. Nevertheless, a major shortage is encountered in recycling which is related to the sorting of plastic wastes. In this paper, a feasibility study was performed in order to test the potential of an innovative approach combining mid infrared (MIR) spectroscopy with independent components analysis (ICA), as a simple and fast approach which could achieve high separation rates. This approach (MIR-ICA) gave 100% discrimination rates in the separation of all studied plastics: polyethylene terephthalate (PET), polyethylene (PE), polypropylene (PP), polystyrene (PS) and polylactide (PLA). In addition, some more specific discriminations were obtained separating plastic materials belonging to the same polymer family e.g. high density polyethylene (HDPE) from low density polyethylene (LDPE). High discrimination rates were obtained despite the heterogeneity among samples especially differences in colors, thicknesses and surface textures. The reproducibility of the proposed approach was also tested using two spectrometers with considerable differences in their sensitivities. Discrimination rates were not affected proving that the developed approach could be extrapolated to different spectrometers. MIR combined with ICA is a promising tool for plastic waste separation that can help improve performance in this field; however further technological improvements and developments are required before it can be applied at an industrial level given that all tests presented here were performed under laboratory conditions.     

The hydraulic separator Multidune: preliminary tests on fluid-dynamic features and plastic separation feasibility

Recycling of plastic materials is a rapidly developing discipline because of environmental awareness, the need to conserve materials and energy, and the growing demand to increase the production economy. The main problem in plastics recovery and recycling is related to the variety of plastic wastes, even if selective collection occurs. Therefore, plastic materials can be recycled either as mixtures or as single types, separating the different typologies by their physical (size, specific mass, etc.) and/or chemical properties. However, separation of plastics in single typologies by traditional processes and devices is difficult due to their typical low variability in properties. This paper presents a new research development for recycling industry: the Multidune separator. This is a device constructed from a sequence of parallel semi-cylindrical tubes of transparent plastic welded together in a plane. The lower half is shifted laterally and then fixed relative to the upper half. Flow is then induced in the lateral direction normal to the axis of the tubes, creating a main flow channel and two recirculation zones. This apparatus creates a differential transport of particles of low specific mass, near to 1g/cm(3), allowing their separation. The flow field in the Multidune separator is studied via Particle Tracking Velocimetry (PTV). Eulerian analysis of the data is performed to gather information about the fluid-dynamics features established by different hydraulic heads at the inlet of the Multidune. Preliminary tests on monomaterial samples have been performed, varying several operative parameters to determine the best set of values. Therefore, separation tests have been executed on composite samples, obtaining satisfactory results in terms of plastic separation feasibility.     

Estimation of residual MSW heating value as a function of waste component recycling

Recycling of packaging wastes may be compatible with incineration within integrated waste management systems. To study this, a mathematical model is presented to calculate the fraction composition of residual municipal solid waste (MSW) only as a function of the MSW fraction composition at source and recycling fractions of the different waste materials. The application of the model to the Lisbon region yielded results showing that the residual waste fraction composition depends both on the packaging wastes fraction at source and on the ratio between that fraction and the fraction of the same material, packaging and non-packaging, at source. This behaviour determines the variation of the residual waste LHV. For 100% of paper packaging recycling, LHV reduces 4.2% whereas this reduction is of 14.4% for 100% of packaging plastics recycling. For 100% of food waste recovery, LHV increases 36.8% due to the moisture fraction reduction of the residual waste. Additionally the results evidence that the negative impact of recycling paper and plastic packaging on the LHV may be compensated by recycling food waste and glass and metal packaging. This makes packaging materials recycling and food waste recovery compatible strategies with incineration within integrated waste management systems.     

Behaviour of biodegradable plastics in composting facilities

Composting is a preferred treatment strategy for biodegradable plastics (BDPs). In this sense, the collection of BDPs together with organic household wastes is a highly discussed possibility. Under the aspect of the behaviour of BDPs in composting facilities, a telephone survey was carried out with selected composting facility operators. They were interviewed with respect to treated wastes, content of impurities, processes for impurity separation, experiences with biodegradable plastics and assumptions to the behaviour of biodegradable plastics in their facility. Forty percent of the facilities had some experiences with BDPs due to test runs, and also since the occurrence of BDPs in their waste was known. The majority of the operators expressed apprehension regarding an increase of impurities resulting from a combined collection of biowaste and BDPs. In the facilities, measures for the impurity separation from the biowaste were used in common practice - in 33% of the cases, separation of disturbing plastics was done before composting, in 33% after composting, and in 13% before and after composting. The most important separation processes for conventional plastics were sieving and manual sorting. In two cases air classification was also used. When asked about the separation possibility of the conventional but not of the biodegradable plastics in their facilities, the majority of operators were not in a position to comment or they replied that it was not an option. No problems were seen in most cases if the impurity separation follows composting. If impurity separation takes place before composting it was often assumed that the BDPs are mainly separated by sieving. In conclusion, in more than half of the cases, BDPs would not be composted if delivered to a composting facility. Under the actual conditions regarding the collection and the treatment/disposal possibilities, an application of BDPs seems to only be reasonable for clean (i.e., source separated on their own) fractions of BDPs.     

A case study of waste management at the Northern Finnish pulp and paper mill complex of Stora Enso Veitsiluoto Mills

This work presents the current waste management system at the pulp and paper mill complex of Stora Enso Oyj Veitsiluoto Mills at Kemi, Northern Finland. This paper covers examples of case studies carried out at the mill and describes how the wastes and by-products are utilized as a neutralizing agent for acidic wastewaters (i.e., green liquor dregs from the causticizing process), as a hardener in filling mine cavities (i.e., ash from the fluidized bed boiler), as a landscaping agent (i.e., ash as well as the fibre clay from chemical wastewater treatment plant), as a hydraulic barrier material for landfills (i.e., fibre clay), and as a soil enrichment agent (i.e., calcium carbonate from the precipitated calcium carbonate plant). In addition, the wood waste from the wood-handling plant, sawmill, packaging pallet plant and from the groundwood mill, as well as the biosludge from the biological wastewater treatment plant, are all incinerated in the fluidized bed boiler for energy production. Due to effective utilization of the solid wastes generated at the mills, the annual amount of waste to be disposed of in the landfill has decreased between 1994 and 2004 from 42,990 to 6083 tonn (expressed as wet weight). The paper also gives an overview of the relevant European Union legislation on the forest industry and on waste management, as well as of the pulping process and of the generation of major solid wastes in the pulp and paper mills.     

Selective separation of virgin and post-consumer polymers (PET and PVC) by flotation method

More and more polymer wastes are generated by industry and householders today. Recycling is an important process to reduce the amount of waste resulting from human activities. Currently, recycling technologies use relatively homogeneous polymers because hand-sorting waste is costly. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. At present, most waste polymers cause serious environmental problems. Burning polymers for recycling is not practiced since poisonous gases are released during the burning process. Particularly, polyvinyl chloride (PVC) materials among waste polymers generate hazardous HCl gas, dioxins containing Cl, etc., which lead to air pollution and shorten the life of the incinerator. In addition, they make other polymers difficult to recycle.Both polyethylene terephthalate (PET) and PVC have densities of 1.30–1.35 g/cm³ and cannot be separated using conventional gravity separation techniques. For this reason, polymer recycling needs new techniques. Among these techniques, froth flotation, which is also used in mineral processing, can be useful because of its low cost and simplicity.The main objective of this research is to recycle PET and PVC selectively from post-consumer polymer wastes and virgin polymers by using froth flotation. According to the results, all PVC particles were floated with 98.8% efficiency in virgin polymer separation while PET particles were obtained with 99.7% purity and 57.0% efficiency in post-consumer polymer separation.     

包装垃圾的分类与回收利用

包装垃圾是由废弃的包装物产生的固体垃圾,约占我国城市生活垃圾的1/3,虽然政府进行了必要回收,但仍有1/3以上的塑料、玻璃等包装物没能被有效回收利用,成了填埋场的主要填埋物,造成了环境污染和土地、石油等不可再生资源大量浪费。从回收利用和源头减量两方面提出包装垃圾的应对,一是对包装垃圾按来源、成分等进行详细分类,并建议回收处置方法;二是从制定行业政策方面来减少过度包装和扶持再生资源行业健康发展,有效处置包装垃圾等可再生资源。     

New characterisation method of electrical and electronic equipment wastes (WEEE)

Innovative separation and beneficiation techniques of various materials encountered in electrical and electronic equipment wastes (WEEE) is a major improvement for its recycling. Mechanical separation-oriented characterisation of WEEE was conducted in an attempt to evaluate the amenability of mechanical separation processes. Properties such as liberation degree of fractions (plastics, metals ferrous and non-ferrous), which are essential for mechanical separation, are analysed by means of a grain counting approach. Two different samples from different recycling industries were characterised in this work. The first sample is a heterogeneous material containing different types of plastics, metals (ferrous and non-ferrous), printed circuit board (PCB), rubber and wood. The second sample contains a mixture of mainly plastics. It is found for the first sample that all aluminium particles are free (100%) in all investigated size fractions. Between 92% and 95% of plastics are present as free particles; however, 67% in average of ferromagnetic particles are liberated. It can be observed that only 42% of ferromagnetic particles are free in the size fraction larger than 20 mm. Particle shapes were also quantified manually particle by particle. The results show that the particle shapes as a result of shredding, turn out to be heterogeneous, thereby complicating mechanical separation processes. In addition, the separability of various materials was ascertained by a sink–float analysis and eddy current separation. The second sample was separated by automatic sensor sorting in four different products: ABS, PC–ABS, PS and rest product. The fractions were characterised by using the methodology described in this paper. The results show that the grade and liberation degree of the plastic products ABS, PC–ABS and PS are close to 100%. Sink–float separation and infrared plastic identification equipment confirms the high plastic quality. On the basis of these findings, a global separation flow sheet is proposed to improve the plastic separation of WEEE.     

Environmental fads and fallacies

Recycling, believed by many to be accomplished by separate collection or central separation, only increases the cost of waste management until someone buys the junk.Reuse with refundable deposits removes valuable items from the waste stream at the earliest possible point and directly rewards the person who does the work.Biodegradable plastics increase greenhouse gases in comparison to conventional plastics if deposited in a landfill. Biofuels have a very minor effect on greenhouse gases because they represent only a few years retention of carbon, in contrast to fossil fuels which have been stored for millions of years.Composting is not recycling, but the destruction of one-half of the energy value of wastes with the production of a humus similar to, but not as good as, that produced in all good soils. As NPK fertilizer, compost is seldom worth the energy necessary to spread it although it has many special uses to improve poor soils.A large number of the perceived risks from e.g. PVC, dioxins, incineration, furnace ash, waste fuel oil, etc. are derived from assumptions that have been unsupported or refuted by later studies, but which remain strongly entrenched in the public mind.Since it is not possible to set a practical scientific definition of hazardous wastes, legal definitions are established. Some of these limits are influenced by active lobbying of interested commercial parties and may bear little relation to environmental or health risks.Competition between environmental authorities to set the lowest limits for toxic emissions has led to scientifically absurd and destructively expensive legal limits on “popular” pollutants. The result is a greater exposure to other hazards that must be neglected due to lack of funds.     

Model-based prediction of long-term leaching of contaminants from secondary materials in road constructions and noise protection dams

In this study, contaminant leaching from three different secondary materials (demolition waste, municipal solid waste incineration ash, and blast furnace slag) to groundwater is assessed by numerical modeling. Reactive transport simulations for a noise protection dam and a road dam (a typical German autobahn), in which secondary materials are reused as base layers, were performed to predict the breakthrough of a conservative tracer (i.e., a salt) and sorbing contaminants (e.g., PAHs like naphthalene and phenanthrene or heavy metals) at the groundwater table. The dam constructions have a composite architecture with soil covers in inclined layers and distinct contrasts in the unsaturated hydraulic properties of the used materials. Capillary barrier effects result in strong spatial variabilities of flow and transport velocities. Contaminant breakthrough curves at the groundwater table show significant tailing due to slow sorption kinetics and a wide distribution of travel times. While conservative tracer breakthrough depends primarily on subsoil hydraulic properties, equilibrium distribution coefficients and sorption kinetics represent additional controlling factors for contaminant spreading. Hence, the three secondary materials show pronounced differences in the temporal development of leached contaminant concentrations with consequences for breakthrough times and peak concentrations at the groundwater table. Significant concentration reductions due to dispersion occur only if the source concentrations decrease significantly prior to the arrival of the contaminant at the groundwater table. Biodegradation causes significant reduction of breakthrough concentrations only if flow velocities are low.     

Use of recycled plastic in concrete: a review

Numerous waste materials are generated from manufacturing processes, service industries and municipal solid wastes. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. Solid waste management is one of the major environmental concerns in the world. With the scarcity of space for landfilling and due to its ever increasing cost, waste utilization has become an attractive alternative to disposal. Research is being carried out on the utilization of waste products in concrete. Such waste products include discarded tires, plastic, glass, steel, burnt foundry sand, and coal combustion by-products (CCBs). Each of these waste products has provided a specific effect on the properties of fresh and hardened concrete. The use of waste products in concrete not only makes it economical, but also helps in reducing disposal problems. Reuse of bulky wastes is considered the best environmental alternative for solving the problem of disposal. One such waste is plastic, which could be used in various applications. However, efforts have also been made to explore its use in concrete/asphalt concrete. The development of new construction materials using recycled plastics is important to both the construction and the plastic recycling industries. This paper presents a detailed review about waste and recycled plastics, waste management options, and research published on the effect of recycled plastic on the fresh and hardened properties of concrete. The effect of recycled and waste plastic on bulk density, air content, workability, compressive strength, splitting tensile strength, modulus of elasticity, impact resistance, permeability, and abrasion resistance is discussed in this paper.     

Determining distribution coefficients for low cost adsorbents

As with other construction materials, coal fly ash contains trace metals that can leach into the natural environment. As part of a broader effort to encourage appropriate coal combustion product use in infrastructure applications (e.g., road construction, stabilization, and structural fill), this study evaluated traditional and low‐cost adsorbent alternatives for their capacity to attenuate trace metals. Batch sorption tests were used as a preliminary screen for a wide variety of low cost (e.g., steel byproducts, rubber dust, and compost) and innovative materials (e.g., kudzu, biofilm, and pond weed) as well as conventional materials (activated carbon, alumina, and zeolites). The removal rates were demonstrated in this study by observing the calculated distribution coefficient (K_d) which were determined using a program called MATLAB. Limestone and steel byproducts were found to be particularly effective with large K_d values of 15,740, 1,520, and 540 L kg^?1 for cadmium, chromium, and selenium and, for ladle refractory and mill scale, K_d values of 3,910, 670, and 1,760 L kg^?1 were observed. Among the three metals tested for this study, it was observed that most low cost and innovative materials removed cadmium quite efficiently; however, the removal of selenium and chromium depended on the substrate and prevailing pH. In general, these results suggest that alternative materials may have relevance in niche applications where leaching is a concern that can be addressed through enhanced attenuation capacity via blending or layering of adsorbents.     

Separation of plastic waste via the hydraulic separator Multidune under different geometric configurations

The recovery of high-quality plastic materials is becoming an increasingly challenging issue for the recycling sector. Technologies for plastic recycling have to guarantee high-quality secondary raw material, complying with specific standards, for use in industrial applications. The variability in waste plastics does not always correspond to evident differences in physical characteristics, making traditional methodologies ineffective for plastic separation. The Multidune separator is a hydraulic channel allowing the sorting of solid particles on the basis of differential transport mechanisms by generating particular fluid dynamic conditions due to its geometric configuration and operational settings. In this paper, the fluid dynamic conditions were investigated by an image analysis technique, allowing the reconstruction of velocity fields generated inside the Multidune, considering two different geometric configurations of the device, Configuration A and Configuration B. Furthermore, tests on mono- and bi-material samples were completed with varying operational conditions under both configurations. In both series of experiments, the bi-material samples were composed of differing proportions (85% vs. 15%) to simulate real conditions in an industrial plant for the purifying of a useful fraction from a contaminating fraction. The separation results were evaluated in terms of grade and recovery of the useful fraction.     

Molecular Modification and Compatibilization of Collected Polyethylene

The increasing use of plastics in packaging materials leads to growing amounts of plastic waste. Recycling material is generally regarded as advantageous. But in fact very few products are made from plastic waste, partly this can be explained by that little is known about the recycling process and the properties of collected materials. There is a need for injection moulding grades of recycled polyethylene, while large amounts of extrusion grades are available from packaging waste. A controlled way of de-branching or partly degrading PE would be desirable. Peroxides are commonly used to crosslink polyolefins, but under certain conditions a chain scission reaction occur. Another problem encountered with recycling of polyethylene are the poor miscibility of low amounts contaminations, i. e. polypropylene. A compatibilizer can improve properties of such polymer blends, in this work EPDM is used as compatibilzer. Studies of mechanical properties and viscosity measurements show that it is possible to partly degrade PE with peroxide exposing it to high temperature and oxygen. The properties of PE/PP blends were improved with EPDM as compatibilizer.     

Mechanical, Thermal and Water Absorption Properties of Kenaf-Fiber-Based Polypropylene and Poly(Butylene Succinate) Composites

The use of composites made from non-biodegradable conventional plastic materials (e.g., polypropylene, PP) is creating global environmental concern. Biodegradable plastics such as poly(butylene succinate) (PBS) are sought after to reduce plastic waste accumulation. Unfortunately, these types of plastics are very costly; therefore, natural lignocellulosic fibers are incorporated to reduce the cost. Kenaf fibers are also incorporated into PP and PBS for reinforcing purposes and they have low densities, high specific properties and renewable sourcing. However without good compatibilization, the interfacial adhesion between the matrix and the fibers is poor due to differences in polarity between the two materials. Maleic anhydride-grafted compatibilizers may be introduced into the system to improve the matrix-fiber interactions. The overall mechanical, thermal and water absorption properties of PP and PBS composites prepared with 30 vol.% short kenaf fibers (KFs) using a twin-screw extruder were being investigated in this study. The flexural properties for both types of composites were enhanced by the addition of compatibilizer, with improvements of 56 and 16 % in flexural strength for the PP/KF and PBS/KF composites, respectively. Good matrix-fiber adhesion was also observed by scanning electron microscopy. However, the thermal stability of the PBS/KF composites was lower than that of the PP/KF composites. This result was confirmed by both DSC and TGA thermal analysis tests. The water absorption at equilibrium of a PBS composite filled with KFs is inherently lower than of a PP/KF composite because the water molecules more readily penetrate the PP composites through existing voids between the fibers and the matrix. Based on this research, it can be concluded that PBS/KF composites are good candidates for replacing PP/KF composites in applications whereby biodegradability is essential and no extreme thermal and moisture exposures are required.     

Development of a testing method for asbestos fibers in treated materials of asbestos containing wastes by transmission electron microscopy

Appropriate treatment of asbestos-containing wastes is a significant problem. In Japan, the inertization of asbestos-containing wastes based on new treatment processes approved by the Minister of the Environment is promoted. A highly sensitive method for testing asbestos fibers in inertized materials is required so that these processes can be approved. We developed a method in which fibers from milled treated materials are extracted in water by shaking, and are counted and identified by transmission electron microscopy. Evaluation of this method by using asbestos standards and simulated slag samples confirmed that the quantitation limits are a few million fibers per gram and a few μg/g in a sample of 50 mg per filter. We used this method to assay asbestos fibers in slag samples produced by high-temperature melting of asbestos-containing wastes. Fiber concentrations were below the quantitation limit in all samples, and total fiber concentrations were determined as 47–170 × 10^?6 f/g. Because the evaluation of treated materials by TEM is difficult owing to the limited amount of sample observable, this testing method should be used in conjunction with bulk analytical methods for sure evaluation of treated materials.     

Fundamental characteristics of input waste of small MSW incinerators in Korea

Waste incineration in a small incinerator is a simple and convenient way of treating waste discharged from small areas or from large facilities and buildings such as business centers, marketplaces, factories, and military units. Despite their ostensible advantages, however, many small incinerators frequently suffer from serious problems, e.g., unsystematic waste feeding, unstable combustion, deficient air pollution control devices, and consequently, environmental pollution. To obtain a better understanding of the characterization of wastes in small incinerators, we investigated a series of fundamental characteristics, i.e., physical composition, bulk density, proximate and ultimate analysis, potential energy content, and so on. The main waste components in small incinerators were identified as paper and plastic; the proportion of food waste was less than that in large incinerators. Especially, a low ratio of food waste had a strong influence on other waste characteristics, e.g., lower moisture content and bulk density, and higher potential energy. On the other hand, in contrast with that of HCl, there was no distinguishable linear relationship between Cl content in waste and PCDD/DF concentration in combustion gas.