我国南方某城市垃圾焚烧飞灰特性及固化/稳定化处置实验

我国南方某城市主要采用焚烧法处理生活垃圾,已建7个焚烧厂日产生飞灰量为101.62 t/d。文章分析了各个垃圾焚烧厂飞灰的化学组成和重金属浸出毒性,其主要成分为CaO、SiO2、MgO、Al2O3、Fe2O3、Na2O、SO3和Cl,所有焚烧飞灰都有至少一种重金属浸出浓度超标,属于危险废物。在飞灰处置出路亟待解决的背景下,实验探讨了飞灰稳定化工艺,结果表明10%的水泥添加量可以使飞灰中超标重金属(Cd、Pb和Zn)的浸出浓度满足危险废物鉴别浓度限值和安全填埋场入场浓度限值。同时,通过人体健康风险评价分析了飞灰豁免管理的可行性,并对近期和远期该城市焚烧厂飞灰的处理处置及管理提出建议。     

中国控制危险废物越境转移管理现状与展望

按照环境无害化管理原则,严格限制危险废物越境转移活动是中国履行《控制危险废物越境转移及其处置巴塞尔公约》的重要内容。本研究通过梳理《控制危险废物越境转移及其处置巴塞尔公约》关于控制危险废物越境转移的主要规定和中国立法管理实践,全面分析了中国控制危险废物越境转移管理进展。从打击非法转移、完善法律基础、建立预警机制等方面,深入剖析了中国控制危险废物越境转移面临的形势,并从强化危险废物越境转移管控、严厉打击非法出口行为、联合海关部门加强日常监管三方面提出对策建议,以期为中国全面履行《控制危险废物越境转移及其处置巴塞尔公约》要求、控制和防范危险废物越境转移环境风险提供支撑。     

Physical and chemical characterisation of metal finishing industrial wastes

In EU countries approximately 150,000 tons/year of galvanic sludges are generated by 4000 industrial units from the corresponding wastewater treatment plants. These sludges are generally classified as hazardous (European Waste Catalogue as adopted in Council Decision 2000/532/CE and as amended by Decisions 2001/118/EC, 2001/119/EC and 2001/573/CE), basically due to the presence of heavy metals. This work attempts to better understand the physical and chemical characteristics of these sludges, by studying 39 samples collected in different Portuguese industries that should represent all kinds of similar wastes independent of their place of generation. Chemical composition and leaching characteristics are given, together with density, grain size distribution, and specific surface area values. Statistical analysis was used for grouping the wastes according to chemical parameters, which might be useful to predict potential reuse as raw materials for different applications.     

An overview for the utilization of wastes from stainless steel industries

Significant quantities of wastes are generated as the waste materials or byproducts every day from stainless steel processes. According to the origins and characteristics, the stainless steel wastes can be mainly classified into two categories, slags and dusts. They usually contained considerable quantities of valuable metals and materials. This paper summarized and analyzed the generation, composition, characteristics and the leaching behaviors of the most of wastes obtained from the stainless steel processes. On this basis, a review of several methods for treating the various stainless steel wastes was made. It is very essential not only for recycling the valuable metals and mineral resources but also for protecting the environment.     

Leaching characteristics of copper flotation waste before and after vitrification

Copper flotation waste from copper production using a pyrometallurgical process contains toxic metals such as Cu, Zn, Co and Pb. Because of the presence of trace amounts of these highly toxic metals, copper flotation waste contributes to environmental pollution. In this study, the leaching characteristics of copper flotation waste from the Black Sea Copper Works in Samsun, Turkey have been investigated before and after vitrification. Samples obtained from the factory were subjected to toxicity tests such as the extraction procedure toxicity test (EP Tox), the toxicity characteristic leaching procedure (TCLP) and the "method A" extraction procedure of the American Society of Testing and Materials. The leaching tests showed that the content of some elements in the waste before vitrification exceed the regulatory limits and cannot be disposed of in the present form. Therefore, a stabilization or inertization treatment is necessary prior to disposal. Vitrification was found to stabilize heavy metals in the copper flotation waste successfully and leaching of these metals was largely reduced. Therefore, vitrification can be an acceptable method for disposal of copper flotation waste.     

Heavy metal removal and cyanide destruction in the metal plating industry: an integrated approach from egypt

Wastewater produced from a metal plating is a major environmental problem. Industrial auditing revealed that the main source of pollution mainly originated from rinsing water. The characterization of final effluent showed that it is highly contaminated with hazardous heavy metals and cyanide. The concentration of copper, hexavalent chromium, nickel, and cyanide in the rinsing water of metal plating department was 14.8, 40.9, 13.3, and 19 mg/l, respectively. The concentration of cyanide and zinc from the galvanizing department reached 60 and 80 mg/l. The remediation scheme included the application of in-plant control measures via changing the rinsing process followed by the destruction of cyanide and reduction of hexavalent chromium bearing wastes. The pretreated wastes were then mixed with other industrial wastes prior to a combined chemical coagulation-sedimentation using lime and/or lime in combination with ferric chloride. The results indicated that, after applying the waste minimization measures alone at the source, prior to final treatment of industrial waste, removal rates of cyanide, copper, nickel, and chromium concentrations were 23.2%, 14.9%, 32.3%, and 55.3%, respectively in the rinse water from metal plating department. Furthermore, the removal rates of cyanide and zinc in the galvanizing department reached 59.7% and 24.3. The integrated control measures and treatment scheme led to more than 99% removal of copper, nickel, chromium, and zinc, while the complete removal of cyanide was achieved in the final effluent.     

建立有效回收网络,防治危险废物污染环境

工业废弃物中，废酸碱、重金属、废矿物油等都属于危险废物，我们日常生活中的废电池、灯管、显像管、空调、冰箱等都含有大量成分的危险废物。开展危险废物的有效回收，建立有效回收网络，才能从根本上防治危险废物进入环境，防治危险废物给人类与环境造成严重灾难。     

Zinc recovery from hazardous construction wastes via an integrated process of the air classification,alkaline leaching,and water washing

Zinc- and lead-containing wastes are often mixed with construction and demolition wastes in many factories, generating abundant of heavy metal-enriched hazardous waste. In the present study, a novel integrated process of air classification, alkaline leaching, and water washing dechlorination was proposed for the efficient recycling of Zinc (Zn) resources. The first air classification process was realized via venturi tube, wherein the content of Zn could increase by 20 wt.%. After that, the product underwent an alkaline leaching process. Results showed that Zn recovery rate increased with fine particle sizes, and a 65% recovery rate was obtained under the following conditions of 5 mol/L NaOH, liquid/solid 10:1, and leaching time 1 h. Finally, water washing associated with microwave and ultrasonic treatments could remove over 85% of Cl and other water-soluble salts. All the results indicated that the integrated method had an excellent recovery rate for Zn resources from construction and demolition wastes.     

A novel extractant for removal of hazardous metals from preservative-treated wood waste

The purpose of this study was to develop a one-step metal extraction process that would effectively remove hazardous elements from wood powder or chips of western hemlock [Tsuga heterophylla (Raf.) Sarg.] treated with chromated copper arsenate (CCA) preservative. In addition, we tested this method for wood treated with other copper-based preservatives such as ammoniacal copper quaternary (ACQ) and copper, boron, and azole (CuAz). A bioxalate solution consisting of 0.125 M oxalic acid adjusted to pH 3.2 with sodium hydroxide was tested for its ability to extract chromium, copper, and arsenic from wood treated with CCA and copper from ACQ, CuAz, or a mixture of CCA-, ACQ-, and CuAz-treated wood in single step. The extraction proceeded efficiently with 6 h of treatment, and was insensitive to the differences in chemical characteristics, including solubility of individual elements. After 6 h of treatment, approximately 90% of chromium, copper, and arsenic were effectively removed from wood treated with CCA or a mixture of CCA, ACQ, and CuAz and 90% of copper from ACQ- and CuAz-treated wood. These results demonstrate that the solvent extraction technique using pH-adjusted bioxalate solution with sodium hydroxide is a promising method for pollution minimization by various types of wastes contaminated with heavy metals and arsenic.     

垃圾焚烧飞灰中重金属的固化/稳定化处理实验研究

研究了城市生活垃圾焚烧-电灰的特性及飞灰中重金属的特性,对利用水泥作粘结剂进行飞灰固化/稳定化处理效果开展了系统的实验研究,分析了水泥固化/稳定化飞灰的工艺特点和最佳工艺参数,并讨论了粘结剂固化飞灰机理以及重金属浸出毒性,为进一步研究城市生活垃圾焚烧飞灰的无害化处理与利用提供了有重要价值的参考依据.     

Formulation of criteria for pollution control on cement products produced from solid wastes in China

The process of producing cement products from solid waste can increase the level of pollutants in the cement products. Therefore, it is very important to establish a pollution control standard for cement products to protect the environment and human health. This paper presents acceptance limits for the availability of heavy metals in cement products which have been produced from solid wastes and explains how the limits have been calculated. The approach and method used to formulate these criteria were based on EN 12920. The typical exposure scenarios used in this paper involve concrete being used for drinking water supply pipelines and concrete pavements and are based on an analysis of typical applications of cement in China, and the potential for contact with water. The parameters of a tank test which was based on NEN 7375 were set in accordance with the environmental conditions of typical scenarios in China. Mechanisms controlling the release of heavy metals in concrete and a model for that release were obtained using the leaching test. Finally, based on acceptance criteria for drinking water and groundwater quality in China, limit values for the availability of heavy metals in concrete were calculated.     

低含油污泥固化处理技术研究*

针对辽河油田欢采水厂低含油污泥,采用固化处理方法,测定了固化剂用量对抗压强度的影响和促凝剂用量对固化时间的影响,得到含油污泥:固化剂:促凝剂最佳配比为100:12:1.5。对含油污泥固化块进行浸出液毒性监测,分析结果表明:含油污泥固化块浸出液中重金属Cu、Pb、Cr、As、Zn、Ni、Cd的含量明显降低,远低于GB5085.3-2007《危险废物鉴别标准浸出毒性鉴别》;浸出液中COD降低了77%。     

A Paradigm of International Environmental Law: The Case for Controlling the Transboundary Movements of Hazardous Wastes

The production of large quantities of wastes globally has created a commercial activity involving the transfrontier shipments of hazardous wastes, intended to be managed at economically attractive waste-handling facilities located elsewhere. In fact, huge quantities of hazardous wastes apparently travel the world in search of “acceptable” waste management facilities. For instance, within the industrialized countries alone, millions of tonnes of potentially hazardous waste cross national frontiers each year on their way for recycling or to treatment, storage, and disposal facilities (TSDFs) because there is no local disposal capacity for these wastes, or because legal disposal or reuse in a foreign country may be more environmentally sound, or managing the wastes in the foreign country may be less expensive than at home. The cross-boundary traffic in hazardous wastes has lately been under close public scrutiny, however, resulting in the accession of several international agreements and laws to regulate such activities. This paper discusses and analyzes the most significant control measures and major agreements in this new commercial activity involving hazardous wastes. In particular, the discussion recognizes the difficulties with trying to implement the relevant international agreements among countries of vastly different socioeconomic backgrounds. Nonetheless, it is also noted that global environmental agreements will generally be a necessary component of ensuring adequate environmental protection for the world community—and thus a need for the careful implementation of such agreements and regulations.     

Soil properties in the metropolitan region of Ibadan, Nigeria: implications for the management of the urban environment of developing countries

This paper examines the variation in the properties of surface soils from the rural, through sub-urban, to the urban zones of Ibadan metropolitan area, south-west Nigeria. Soils were sampled at 0–20 cm depth in the northern part of the metropolis. Statistical techniques were used to compare the data obtained in the three zones. The results of the analyses clearly show that the mean values of nine out of the eighteen soil properties analysed differed significantly between the three zones. In particular, the concentration of two of the three heavy metals analysed in the study, that is, zinc and lead were higher in the urban zone than in the other two zones. The accumulation of heavy metals in the soils of the urban environment of developing countries requires urgent attention from environmentalists and urban development planners. It is important to prevent such heavy metals leaching into the underground water supply, and, to minimise the health risks to both humans and animals that depend solely on this source of water supply.     

Mechanisms controlling the leaching kinetics of fixated flue gas desulfurization (FGD) material under neutral and acidic conditions

A number of agricultural and engineering uses for fixated flue gas desulfurization (FGD) material exist; however, the potential for leaching of hazardous elements has limited widespread application and the processes controlling the leaching of this material are poorly understood. In this study, a flow-through rotating-disk system was applied to elucidate the relative importance of bulk diffusion, pore diffusion, and surface chemical reaction in controlling the leaching of fixated FGD material under pH conditions ranging from 2.2 to 6.8. Changing the hydrodynamics in the rotating disk system did not affect the leaching kinetics at both pH 2.2 and 6.8, indicating that bulk diffusion was not the kinetic-limiting step. Application of the shrinking core model (SCM) to the data suggested a surface reaction-controlled mechanism, rather than a pore diffusion mechanism. The leaching of fixated FGD material increased with decreasing pH, suggesting it can be described by a combination of an intrinsic hydration reaction and a proton-promoted dissolution reaction. X-ray diffraction (XRD) and elemental composition analyses before and after leaching suggests that for most elements a number of solid phases controlled the leaching process.     

酸沉降物对土壤化学性质的影响

本文综述了酸沉降物对土壤酸化、营养物质的淋溶、重金属的活化、矿物分解等化学性质的影响，以及阻止酸雨危害土壤的化学方法。     

Preservative leaching from weathered CCA-treated wood

Disposal of discarded chromated copper arsenate (CCA)-treated wood in landfills raises concerns with respect to leaching of preservative compounds. When unweathered CCA-treated wood is leached using the toxicity characteristic leaching procedure (TCLP), arsenic concentrations exceed the toxicity characteristic (TC) limit of 5mg/L in most cases. The majority of discarded CCA-treated wood, however, results from demolition activities, where the wood has typically been subjected to weathering. Since preservatives do migrate from the wood during its normal use, leaching characteristics of weathered and aged CCA-treated wood may differ from unweathered wood. To evaluate this, CCA-treated wood removed from service after various degrees of weathering was collected from multiple sources and leached with the TCLP, the synthetic precipitation leaching procedure (SPLP) and California's waste extraction test (WET). Five to seven individual pieces of wood were analyzed from each source. The average TCLP arsenic concentration for the 14 sources ranged from 3.2 to 13 mg/L. The average TCLP concentrations of the 100 wood pieces tested were 6.4, 5.9 and 3.2 mg/L for arsenic, copper and chromium, respectively. Overall, in 60 out of 100 samples tested by the TCLP, arsenic concentrations exceeded 5 mg/L (the TC regulatory value). SPLP leachate concentrations were similar to TCLP concentrations, although copper leached somewhat more with the TCLP. WET leachate concentrations were approximately a factor of 10 higher than TCLP concentrations. Discarded CCA-treated wood, even after exposure to years of weathering, often exceeds the TC limit for arsenic and without the current regulatory exemption would possibly require management as a TC hazardous waste in the US.     

Leachability of printed wire boards containing leaded and lead-free solder

Due to environmental concerns and regulatory initiatives, electronics manufacturers are replacing the tin/lead solder commonly used on printed wire boards (PWBs) with alternative solders. To determine the potential waste management impacts of the alternative solders versus the tin/lead solder, two leaching tests on PWBs manufactured with five alternative types of solder were performed: the toxicity characteristic leaching procedure (TCLP) and the synthetic precipitation leaching procedure (SPLP). These tests are commonly used in the US regulatory community to assess pollutant leachability in different disposal scenarios. The article discusses the application and limitations of these tests. The five types of solders investigated were 63Sn/37Pb, 99.3Sn/0.7Cu, 95.5Sn/4Ag/0.5 Cu, 96Sn/2.5Ag/1Bi/0.5Cu, and 42Sn/1Ag/57Bi. The leaching tests were conducted on four PWB sections, each with a unique configuration and solder density. The largest lead concentrations were observed from the PWBs containing Sn/Pb solder, with concentrations exceeding the hazardous waste toxicity characteristic (TC) in TCLP leachates. Silver, the other regulated element used in the solders, was rarely detected, with none of the samples exceeding the TC limit for silver. High copper concentrations were observed and were determined to result from the PWB itself, not from the copper-containing solders.     

回转窑在处理危废铬渣中的应用

铬渣主要指铬盐厂生产过程中产生的有毒废渣,属于危险废物,其危害源自于所含的毒性很大的六价铬。文章介绍了危险废物处理行业中采用回转窑焚烧处理铬渣,及后续烟气净化、彻底无害化处理的工艺设计过程。为铬渣的处理提供了一套系统高效的处理方式。     

Biosorption of copper (II) from chemical mechanical planarization wastewaters

Copper Chemical Mechanical Planarization (Cu-CMP) is a critical step in integrated circuit (IC) device manufacturing. CMP and post-CMP cleaning processes are projected to account for 30-40% of the water consumed by IC manufacturers in 2003. CMP wastewater is expected to contain increasing amounts of copper as the industry switches from Al-CMP to Cu-CMP causing some IC manufacturers to run the risk of violating discharge regulations. There are a variety of treatment schemes currently available for the removal of heavy metals from CMP wastewater, however, many introduce additional chemicals to the wastewater, have large space requirements, or are expensive. This work explores the use of microorganisms for waste treatment. A Staphylococcus sp. of bacteria was isolated and studied to determine the feasibility for use in removing copper from Cu-CMP wastewater. A model Cu-CMP wastewater was developed and tested, as well as actual Cu-CMP wastes. Continuous-flow packed column experiments were performed to obtain adsorption data and show copper recovery from the waste. A predictive, empirical model was used to accurately describe Cu removal. Additionally, the immobilized cells were regenerated, allowing for the concentration and potential recovery of copper from the wastewater.