填充竹炭对微生物燃料电池性能的影响

微生物燃料电池(MFC)的阳极对提高MFC产电性能有至关重要的影响。利用竹炭比表面积大、吸附能力强等特性,将其作为"三合一"膜电极MFC的阳极填充材料,通过增大阳极比表面积来提高其产电能力。实验结果表明,加入竹炭至阳极室后,MFC最高输出电压(外接电阻1 000Ω时)由0.280V增大到0.387V,提高了38.2%,并且输出电压更加稳定;而最大功率密度也由原来的0.22W/m3增大到1.42W/m3,同时内阻降低了80.85%(由235Ω降为45Ω);库仑效率由15.0%增大到25.6%。说明MFC阳极室填充竹炭可以显著促进MFC的产电性能。     

对硝基苯酚生物电化学还原过程及优势菌群生物群落分析

通过向阴极室投加接种污泥构建阴极功能型的微生物燃料电池(MFC),并用其强化降解对硝基苯酚(PNP),考察了MFC运行过程中电极液pH、电导率和温度等环境因子的变化,使用SPSS 13.0统计分析软件考察了各环境因子与MFC输出电压的相关关系,并对阴极生物膜样品采用高通量测序分析其菌群结构。结果表明,MFC输出电压与阳极室、阴极室pH均呈极显著相关关系,电极液pH为6时MFC对PNP的降解性能较优,PNP降解率为100.0%,还原降解中间产物对氨基苯酚(PAP)生成率为32.5%±2.5%,而pH为4时PNP降解率为80.1%±4.1%,PAP生成率为13.3%±2.2%;外接电阻为100Ω时,MFC对PNP降解性能优于外接电阻50、200Ω时。阴极优势菌群中,懒杆菌科(Ignavibacteriaceae)推动了系统电子的传递,而嗜氢菌目(Hydrogenophilales)、伯克霍尔德氏菌目(Burkholderiales)具有辅助还原降解PNP的作用。     

双室微生物燃料电池型BOD传感器性能

构建了双室微生物燃料电池(MFC),并应用于污水BOD的检测。优化了MFC型BOD传感器的检测条件,分析了传感器进行污水BOD检测的特征。结果表明,以A2/O污水处理工艺中厌氧段污泥进行接种,双室MFC型BOD传感器2周内完成启动,所产电流达到稳定。传感器的最佳检测条件为外接电阻500Ω,添加缓冲溶液并维持待测水样pH为7.0,添加35 mg/L的L-半胱氨酸作为吸氧剂维持阳极室厌氧环境,阴极室富氧水流量为20 mL/min。利用MFC产生的电流峰值准确检测污水水样BOD浓度,传感器检测范围为10~50 mg/L,检测时间小于3 h;利用MFC产生的电荷量准确检测污水水样BOD浓度,检测范围为10~100 mg/L,检测时间小于10 h。利用MFC电流峰值和电荷量检测污水水样BOD浓度,偏差均小于15%,传感器运行稳定,寿命较长。     

微生物燃料电池阴阳两级分步降解对氯酚效果

构建一种微生物燃料电池(MFC),首先将对氯酚在阴极室降解为苯酚,随后将阴极处理液在阳极室降解。研究了对氯酚废水经过阴阳双室分步处理后的去除效果和该MFC的产电性能,结果表明,在外电阻1 000Ω时,阴极脱氯阶段最大输出电压为216 m V,产电周期为132 h;阳极降解阶段最大输出电压为277 m V,产电周期为48 h,对氯酚的总去除率为96.2%。实验结果表明该MFC能较好处理对氯酚废水,且与传统的生化处理技术相比,有较大的优势。     

共基质下微生物燃料电池同步脱色甲基橙与产电性能

采用双室方形微生物燃料电池(MFC),以葡萄糖作为共基质,研究了共基质浓度对典型偶氮染料甲基橙在MFC阳极室中脱色效率及同步产电的影响。结果表明,在0~1.5 g/L浓度范围内,共基质浓度越大,甲基橙脱色率、COD去除率和最大输出电压越高。在共基质浓度为1.5 g/L,进水甲基橙为300 mg/L的条件下,8 h的脱色率高达95%,且在1 000Ω外电阻下,最大输出电压达到662 m V;在无共基质条件下,8 h内对300 mg/L甲基橙的脱色率仅为7.5%,最大输出电压仅达到140 m V。厌氧对照实验表明,甲基橙在MFC中可以实现加速脱色,反应8 h后甲基橙在MFC中的脱色率提高了57%。该研究为开发新型MFC降解偶氮染料废水技术提供了理论依据。     

生物阴极式碳纸隔膜微生物燃料电池的反硝化和产电性能

为了探讨生物阴极式廉价隔膜微生物燃料电池(microbial fuel cell,MFC)的基本性能,首先以生物反硝化作用为基础构建了生物阴极MFC,并进一步以涂布聚四氟乙烯(PTFE)的廉价碳纸代替昂贵的质子交换膜(PEM)构建碳纸隔膜生物阴极式MFC。研究结果显示,对于生物阴极式MFC,阴极室中最适宜反硝化细菌生长的NO-3-N浓度为99.2 mg/L,此时输出电压最高可达0.11 V,1 h内NO-3-N的去除率达到80.0%,COD去除率为62.8%;以涂PTFE的碳纸代替PEM的生物阴极式MFC与有PEM的MFC最高输出电压基本一致(均达到0.22 V,外阻500Ω),但碳纸隔膜MFC的产电更稳定。结果验证了廉价隔膜生物阴极式MFC的可行性,并为其应用于污水脱氮奠定基础。     

MFC强化同步短程硝化反硝化工艺的启动

微生物燃料电池(MFC)可在阴极实现反硝化、短程反硝化和同步硝化反硝化并产生电能,但在MFC阴极实现同步短程硝化反硝化的研究尚未见到报道。为了探讨MFC阴极同步短程硝化反硝化工艺的性能,将双室曝气阴极MFC与A/O脱氮工艺结合处理人工模拟低碳氮比废水。通过静置运行15 d使得MFC阴极室亚硝态氮得以积累,氨氧化菌得以富集。随即改为连续运行后第21天成功启动同步短程硝化反硝化MFC;阴极出水氨氮浓度为0.3 mg/L,亚硝态氮浓度为15.9 mg/L,硝态氮浓度为0.6 mg/L,亚硝化率达到95%以上,阴极电极自养反硝化去除率达到50%以上,COD去除率达到85%以上。结果表明,将MFC与同步短程硝化反硝化工艺结合,通过阴极室中氧气得电子获得高p H,可以强化同步短程硝化反硝化工艺,完成生物脱氮的同时回收电能,并具有减少外加碱度的优势。     

厌氧污泥和Geobacter sulfurreducens接种MFC的产电性能及其修复Cd污染土壤研究

利用混合菌种(厌氧污泥)和单一菌种(Geobacter sulfurreducens)以不同接种方式搭建单室土壤微生物燃料电池(MFC)反应器,考察不同MFC的产电性能及其对Cd污染土壤的修复效果。结果表明,将混合菌种集中接种于阳极碳毡表面的MFC1运行效果最佳,其在2d即可完成启动,输出电压稳定在0.225V左右,最大功率密度为35.00MW/m2,内阻为515.5Ω。土壤修复效果与MFC产电性能相关,MFC1产电性能最佳,因此土壤修复效果最好,稳定运行30d后阴极Cd富集率最高,达19.02%     

阳极电势对MFC中产电的影响

在微生物燃料电池(MFC)中,与微生物接触的阳极自身电场环境就可能会对产电菌的生长和代谢产生重要影响,进而影响到MFC产电效能。为探索阳极电势的作用,本研究在微生物燃料电池的阳极室中通过设置附加电路来人为改变阳极电势,考察了阳极电势对MFC产电的影响。结果表明,当阳极电势在-380 mV降低到0 mV过程中,MFC输出功率提高。当阳极电势小于200 mV时,COD去除效率在60%~73%之间变化不大。较低或较高的阳极电势均可增加电池的库伦效率。阳极电势处于-380 mV到0 mV下,厌氧微生物主要以丙酸型发酵为主,产生大量乙酸;COD的分解和利用是分阶段进行的。不同阳极电势下MFC内阻变化主要受浓差内阻影响。阳极电势为-200 mV时欧姆内阻最低,但电化学活性较高。     

以不同底物和苯胺为燃料的微生物燃料电池的产电特性

通过构建空气阴极型双室微生物燃料电池,研究了以500 mg/L苯胺作为唯一燃料以及苯胺和不同底物共基质时MFC对苯胺的降解特性及MFC的产电性能。结果表明,在外电阻1 000Ω,以500 mg/L苯胺为唯一燃料以及500 mg/L苯胺分别和500 mg/L乙酸钠,葡萄糖和可溶性淀粉作为共同基时的MFC运行周期分别为3、3.4、4.6和5 d;最大输出电压分别为273、450、428和380 m V;输出功率分别为142、225、201和160 m W/m2。苯胺去除率分别为68%、85.8%、71%和65%。内阻分别为931、524、564和751Ω,COD去除率分别为68%、85%、72%和65%。库伦效率分别为1.8%、7.9%、6.6%和4.5%。MFC可以使用苯胺作为唯一燃料,且当添加的基质不同时,MFC产电性能以及苯胺降解状况有所不同。利用MFC可以使苯胺高效快速降解的同时实现稳定的电压输出。     

不同驯化方式对以苯酚为基质的微生物燃料电池产电性能的影响

以厌氧污泥作为初始接种体,构建了单室微生物燃料电池（MFCs）,考察了梯度驯化、直接驯化和间接驯化3种不同驯化方式对MFC降解苯酚及产电性能的影响。结果表明,MFC在闭路状态下对苯酚的降解速率比MFC在开路状态下的苯酚降解速率加快10%～20%,说明MFC在产电的同时,可加速苯酚的降解。当以600 mg/L的苯酚溶液为单一燃料,反应68 h后,3种驯化方式下的MFC对苯酚降解率都达到90%以上。相对于其他2种驯化方式,梯度驯化条件最有利于MFC产电性能的提高及苯酚的降解,其最大输出功率为31.3 mW/m2,降解速率提高了7%～20%。     

双室微生物燃料电池同时去除废水中的苯酚和硝酸盐

构建了一种双室微生物燃料电池,以苯酚为阳极燃料,同时去除阴极室的硝酸盐废水。结果表明,在闭合情况下,该微生物燃料电池阳极室的苯酚降解效率达到7.6 mg/(L·h),是开路情况下的2倍;反应开始后的5 d内,闭合系统阴极室硝酸盐降解效率达到4.43 mg/(L·d),是开路情况下的2倍多,表明了该MFC系统可以同时去除废水中2种难降解污染物,并且与传统的生物降解方式相比较,具有更快的降解速率。     

Simultaneous bioelectricity generation and decolorization of methyl orange in a two-chambered microbial fuel cell and bacterial diversity

The objectives of this study were to investigate the simultaneous bioelectricity generation and decolorization of methyl orange (MO) in the anode chamber of microbial fuel cells (MFCs) in a wide concentration range (from 50 to 800 mg L^?1) and to reveal the microbial communities on the anode after the MFC was operated continuously for more than 6 months using MO-glucose mixtures as fuel. Interestingly, the added MO played an active role in the production of electricity. The maximum voltage outputs were 565, 658, 640, 629, 617, and 605 mV for the 1 g L^?1 glucose with 0, 50, 100, 200, 300, and 500 mg L^?1 of MO, respectively. The results of three groups of comparison experiments showed that accelerated decolorization of methyl orange (MO) was achieved in the MFC as compared to MFC in open circuit mode and MFC without extra carbon sources. The decolorization efficiency decreased with an increase of MO concentration in the studied concentration range for the dye load increased. A 454 high-throughput pyrosequencing revealed the microbial communities. Geobacter genus known to generate electricity was detected. Bacteroidia class, Desulfovibrio, and Trichococcus genus, which were most likely responsible for degrading methyl orange, were also detected.     

Sodium nitrate as a methanogenesis suppressor in earthen separator microbial fuel cell treating rice mill wastewater

Environmental Science and Pollution Research - The microbial fuel cell (MFC) is one of the sustainable technologies, which alongside treating wastewater, can generate electricity. However, its...     

Production of electricity from proteins using a microbial fuel cell.

Electricity generation was examined from proteins and a protein-rich wastewater using a single chamber microbial fuel cell (MFC). The maximum power densities achieved were 354 +/- 10 mW/m2 using bovine serum albumin (BSA) and 269 +/- 14 mW/m2 using peptone (1100 mg/L BSA and 300 mg/L peptone). The recovery of organic matter as electricity, defined as the Coulombic efficiency (CE), was comparable to that obtained with other substrates with CE = 20.6% for BSA and CE = 6.0% for peptone. A meat packing wastewater (MPW), diluted to 1420 mg/L chemical oxygen demand, produced 80 +/- 1 mW/m2, and power was increased by 33% by adding salt (300 mg/L sodium chloride) to increase solution conductivity. A wastewater inoculum generated 33% less power than the MPW inoculum. The MFC was an effective method of wastewater treatment, demonstrated by >86% of biochemical oxygen demand and total organic carbon removal from wastewater.     

厌氧折流板式微生物燃料电池堆影响因素研究

微生物燃料电池(MFC)中输出电压/电流的提升,以及反应器体积的扩展放大是其工程化应用的关键。本文构建了一个总体积为6.4 L的新型厌氧折流板式微生物燃料电池堆(ABSMFC)。以葡萄糖作为底物,探讨了阳极材料、液面高程差和水力停留时间(HRT)等因素对ABSMFC性能的影响。结果表明,碳纤维毡作为阳极时,电池单体外电路平均分压(R_(ex)=1 000Ω)为210 mV,填充石墨颗粒后增加到319.8 mV。格室间存在液面高程差时,电池单体、串联和并联的功率密度分别为207.1、181.1和215.7 mW/m~2,当无液面高程差(即水力相连)时为205.8、69.5和151.5 mW/m~2。4个电池单体串联和并联连接时,HRT对ABSMFC的产电稳定性无影响,溶解性COD的去除率和库仑效率均随HRT的增加而升高,且并联效果优于串联。     

Comparison of batch, stirred flow chamber, and column experiments to study adsorption, desorption and transport of carbofuran within two acidic soils

Different methods (batch, column and stirred flow chamber experiments) used for adsorption and desorption of carbofuran studies were compared. All tested methods showed that the carbofuran adsorption was higher in the soil with the higher organic matter content, whereas the opposite behaviour was observed for the percentage of carbofuran desorbed. However, different methods have revealed some discrepancies in carbofuran adsorption/desorption kinetics. Although batch method showed interesting data on equilibrium experiments, such as a low heterogeneity for the carbofuran adsorption sites independent of soil organic matter content, it had some disadvantages for carbofuran adsorption/desorption kinetic studies. The disadvantages were related with the excessive limitations of this method on kinetics, i.e., no difference could be detected between different soils. However, with column and stirred flow chamber methods the carbofuran adsorption/desorption kinetics of different soils could be compared. Moreover, the absolute values of carbofuran adsorption/desorption and its rate were higher in the stirred flow chamber than in the batch and column experiments. Using stirred flow chamber experiments the carbofuran desorption was significantly faster than its adsorption, whereas carbofuran using column experiments they were similar. These discrepancies should be considered when the results obtained only with one method is discussed.     

有害物质环境测试组合舱的研制及性能评价

研制了一种新型有害物质环境测试组合舱,该测试舱由舱体系（内舱和外舱）、恒温恒湿空气处理系统、空气循环装置和信号控制与处理软件组成。该测试舱具有可分别使用内舱和外舱对样品进行测试的特点,并采用美国FLUNT公司开发的air pack软件包对内舱和外舱的气流进行模拟与计算,并划分出内舱的层流区域,同时也对舱体系的性能进行了测试与评价。结果表明,有害物质环境测试组合舱的温湿度的相对标准偏差分别为0.04℃和0.7%,混合性达到90.7%。因此,该有害物质环境测试组合舱对温湿度控制精准,气流稳定,混合性能良好,能为室内空气污染研究提供条件稳定的室内仿真环境。     

微生物燃料电池在污水处理中的研究进展

微生物燃料电池(microbial fuel cell,MFC)利用微生物催化剂将其代谢能直接转化为电能,具有原料广泛、反应条件温和、清洁高效等优点.简述了MFC的工作原理及分类,总结了用于污水处理的MFC的性能及其影响因素.探讨了MFC在实际应用中的瓶颈,并展望其在污水处理中的应用前景.     

以两种酚类有机物为基质的微生物燃料电池产电特性

以城市污水处理厂的厌氧污泥为接种微生物,在外电阻为1900Ω下,采用双室微生物燃料电池(MFC)分别对以难降解的有毒有机物2,4-二氯苯酚(DCP),对硝基苯酚(PNP),对硝基苯酚和2,4-二氯苯酚为基质时进行有机物降解和产电性能的研究。实验结果表明以DCP(50 mg/L)为单一基质时,MFC的运行周期长达225 h左右,负载两端的最大电压值达393.7 mV,库仑效率为13.73%;而以PNP和DCP为混合基质时,PNP明显促进DCP的降解,使得DCP的去除率高达64.52%,同时PNP的去除率也达到94.47%。实验最终表明,MFC能够以2,4-二氯苯酚和对硝基苯酚为基质,在实现DCP和PNP降解的同时可稳定高效地向外输出电能。