Effect of combustion variables on PAHs emission from incineration of cellulose waste filters from acrylic industry

Incineration of cellulose waste filter from acrylic industry showed the presence of 13–16 polycyclic aromatic hydrocarbons (PAHs) from the list of 16 priority pollutants with an airflow rate of 1, 2, 3, and 4 L min^???1 in laboratory scale quartz tube vertical incinerator at 700–1,000°C at an interval of 100°C. The amount of total 16 PAHs increases with the increase in temperature with airflow rate of 1 L min^???1 and was found to be 9.4 times at 1,000°C than at 700°C. Studies at 800–1,000°C showed the decrease in total 16 PAHs with increase in airflow rate from 1 to 2 L min^???1. The amount of total 16 PAHs increases at 700, 800, and 1,000°C with increase in airflow rate from 2–4 L min^???1. At 900°C, amount of 16 PAHs decreases with increase in flow rate from 1 to 3 and increases at 4 L min^???1. The lesser amount of 2A PAHs was found at 700–900°C with airflow rates of 1–3 L min^???1, while less amount of 2B PAHs was found at 700°C and 800°C (with airflow rate of 1–2 L min^???1), at 900°C (with airflow rate of 1–3 L min^???1) and at 1,000°C (with airflow rate of 3 L min^???1). However, the sum total of 2A and 2B PAHs were found to be less at 700–900°C with airflow rate of 1–2 L min^???1.     

Polycyclic aromatic hydrocarbons in bulk PM2.5 and size-segregated aerosol particle samples measured in an urban environment

To analyze polycyclic aromatic hydrocarbons (PAHs) at an urban site in Seoul, South Korea, 24-hr ambient air PM_2.5 samples were collected during five intensive sampling periods between November 1998 and December 1999. To determine the PAH size distribution, 3-day size-segregated aerosol samples were also collected in December 1999. Concentrations of the 16 PAHs in the PM_2.5 particles ranged from 3.9 to 119.9 ng m⁻³ with a mean of 24.3 ng m⁻³.An exceptionally high concentration of PAHs(∼120 ng m⁻³) observed during a haze event in December 1999 was likely influenced more by diesel vehicle exhaust than by gasoline exhaust, as well as air stagnation, as evidenced by the low carbon monoxide/elemental carbon (CO/EC) ratio of 205 found in this study and results reported by previous studies. The total PAHs associated with the size-segregated particles showed unimodal distributions. Compared to the unimodal size distributions of PAHs with modal peaks at < 0.12 μm measured in highway tunnels in Los Angeles (Venkataraman and Friedlander, 1994), four- to six-ring PAHs in our study had unimodal size distributions, peaking at the larger size range of 0.28–0.53 μm, suggesting the coagulation of freshly emitted ultrafine particles during transport to the sampling site. Further, the fraction of PAHs associated with coarse particles(> 1.8 μm) increased as the molecular weight of the PAHs decreased due to volatilization of fine particles followed by condensation onto coarse particles.     

Receptor modeling for source apportionment of polycyclic aromatic hydrocarbons in urban atmosphere

This study reports source apportionment of polycyclic aromatic hydrocarbons (PAHs) in particulate depositions on vegetation foliages near highway in the urban environment of Lucknow city (India) using the principal components analysis/absolute principal components scores (PCA/APCS) receptor modeling approach. The multivariate method enables identification of major PAHs sources along with their quantitative contributions with respect to individual PAH. The PCA identified three major sources of PAHs viz. combustion, vehicular emissions, and diesel based activities. The PCA/APCS receptor modeling approach revealed that the combustion sources (natural gas, wood, coal/coke, biomass) contributed 19–97% of various PAHs, vehicular emissions 0–70%, diesel based sources 0–81% and other miscellaneous sources 0–20% of different PAHs. The contributions of major pyrolytic and petrogenic sources to the total PAHs were 56 and 42%, respectively. Further, the combustion related sources contribute major fraction of the carcinogenic PAHs in the study area. High correlation coefficient (R ² > 0.75 for most PAHs) between the measured and predicted concentrations of PAHs suggests for the applicability of the PCA/APCS receptor modeling approach for estimation of source contribution to the PAHs in particulates.     

The Distribution and Sources of Polycyclic Aromatic Hydrocarbons in Surface Sediments Along the Egyptian Mediterranean Coast

Coastal marine sediment samples were collected from 31 sampling stations along the Egyptian Mediterranean Sea coast. All sediment samples were analyzed to determine aliphatic and polycyclic aromatic hydrocarbons (PAHs) as well as total organic carbon (TOC) contents and grain size analysis. Total concentrations of 16 EPA-PAHs in the sediments were varied from 88 to 6338 ng g⁻¹ with an average value of 154 ng g⁻¹ (dry weight). However, the concentrations of total aliphatic were varied from 1.3 to 69.9 ng g⁻¹ with an average value of 15.6 ng g⁻¹ (dry weight). The highest contents of PAHs were found in the Eastern harbor (6338 ng g⁻¹), Manzala (5206 ng g⁻¹) and El-Jamil East (4895 ng g⁻¹) locations. Good correlations observed between a certain numbers of PAH concentrations allowed to identify its origin. The average total organic carbon (TOC) percent was varied from 0.91 to 4.54%. Higher concentration of total pyrolytic hydrocarbons (∑COMB) than total fossil hydrocarbons (∑PHE) declared that atmospheric fall-out is the significant source of PAHs to marine sediments of the Egyptian Mediterranean coast. The selected marked compounds, a principal component analysis (PCA) and special PAHs compound ratios (phenanthrene/anthracene vs fluoranthene/pyrene; ∑COMB/∑EPA-PAHs) suggest the pyrogenic origins, especially traffic exhausts, are the dominant sources of PAHs in most locations. Interferences of rather petrogenic and pyrolytic PAH contaminations were noticed in the harbors due to petroleum products deliveries and fuel combustion emissions from the ships staying alongside the quays.     

Spatial Variability and Monitoring of Pb Contamination of Farming Soils Affected by Industry

In this study, the relationship between some physico-chemical properties of soils and lead contamination in soil due to emission from industrial operations in Samsun province of Turkey was investigated. The extent of timely contamination was studied by comparing the obtained results with the results of the study conducted in the same region in 1998. An area of 225 km² (15 km × 15 km), which was divided into 1000 × 1000 m grid squares (16 lines in the east and south directions), was selected within the industrial area. The total of 256 grid points was obtained and soil samples were collected from three depths (0–5, 5–15, and 15–30 cm) of each grid center in 2004. The total Pb concentrations of soil samples were determined as 65.84–527.04 μg g⁻¹ at 0–5 cm in depth, 58.50 – 399.54 μg g⁻¹ at 5–15 cm in depth, and 44.65–330.07 μg g⁻¹ at 15–30 cm in depth. DTPA-extractable Pb concentrations of soils were found to be in the range of 1.52–9.03 μg g⁻¹, 0.54–7.09 μg g⁻¹, 0.19–6.13 μg g⁻¹ at 0–5, 5–15, and 15–30 cm depths, respectively. There were significant relationships between both total or DTPA-extractable Pb concentrations and selected physico-chemical properties of soil. According to enrichment factor (EF) values calculated from the total Pb concentrations, 11.3% of the study area (225 km²) was enriched with Pb in high level, but 77% of the area was in significant enrichment level with Pb. The average total and DTPA-extractable Pb concentrations increased as 11 and 13%, respectively in comparison with the results of 1998.     

Seasonal Variation of the Particle Size Distribution of n-Alkanes and Polycyclic Aromatic Hydrocarbons (PAHs) in Urban Aerosol of Guangzhou, China

Seasonal aerosol samples have been collected by Andersen Hi-Vol pumping system equipped with a five stage cascade impactor and a backup filter (size range: 10–7.2 μ m, 7.2–3.0 μ m, 3.0–1.5 μ m, 1.5–0.95 μ m, 0.95–0.49 μ m, ≤0.49 μ m) in the Liwan district, Guangzhou. n-Alkanes were measured using gas chromatography and PAHs were measured using gas chromatography/mass spectrometry analysis. The bimodal log-normal distributions of n-alkanes and semi-volatile PAHs were found, while for non-volatile PAHs that was unimodal, so much as the mode of semi-volatile PAHs was similar with that of the particles. The n-alkanes and PAHs were preferably associated with fine particles. C _max (carbon number maximum) (C₂₂–C₂₆), CPI (carbon preference index) (1.12–1.21), U/R (unresolved to resolved components ratio) (7.42–10.7), wax% (0.9–3.12%) and the diagnostic ratios for PAHs revealed that vehicular emission was the major source of these organic compounds during the study periods, while the contribution of epicuticular waxes emitted by terrestrial plants was minor. CPI₂ (values for petrogenic hydrocarbons), CPI₃ (values for biogenic n-alkanes) and wax% revealed that the natural preferentially accumulated in the larger aerosol while the anthropogenic in the smaller. In addition, the different MMDs (mass median diameters) for n-alkanes and PAHs were observed in different seasons. The MMDs for n-alkanes and PAHs were higher in autumn/winter than those in spring/summer. The seasonal effect was related to the hydrocarbon content in the individual particulate fractions, showing a preferential association of n-alkanes and PAHs with larger particles in the autumn/winter season.     

Rinodina sophodes (Ach.) Massal.: a bioaccumulator of polycyclic aromatic hydrocarbons (PAHs) in Kanpur City, India

The aim of this study is to determine the possibility of using Rinodina sophodes (Ach.) Massal., a crustose lichen as polycyclic aromatic hydrocarbons (PAHs) bioaccumulator for evaluation of atmospheric pollution in tropical areas of India, where few species of lichens are able to grow. PAHs were identified, quantified and compared to evaluate the potential utility of R. sophodes. The limit of detection for different PAHs was found to be 0.008–0.050 μg g^− 1. The total PAHs in different sites were ranged between 0.189 ± 0.029 and 0.494 ± 0.105 μg g^− 1. The major sources of PAHs were combustion of organic materials, traffic and vehicular exhaust (diesel and gasoline engine). Significantly higher concentration of acenaphthylene and phenanthrene indicates road traffic as major source of PAH pollution in the city. Two-way ANOVA also confirms that all PAHs content showed significant differences between all sampling sites (P 1%). This study establishes the utility of R. sophodes in monitoring the PAHs accumulation potentiality for development of effective tool and explores the most potential traits resistant to the hazardous environmental conditions in the tropical regions of north India, where no such other effective way of biomonitoring is known so far.     

Levels of PAHs in the soils of Belgrade and its environs

Polycyclic aromatic hydrocarbons (PAHs) were analysed in 39 soil samples (0–10 cm upper layer) collected in Belgrade, the capital of Serbia. The sampling sites were randomly selected from urban, urban/recreational and rural areas; the samples were collected in April and December 2003 and July and October 2004. The sum of the 16 PAHs corresponding to the recreational zone (298 μg/kg) was close to the urban zone (375 μg/kg). Mean soil ΣPAH concentration from rural areas was 18 μg/kg dry weight. Comparing to values observed in the urbanized locations around the world, the overall levels of PAHs in this study are low. The PAH ratios obtained pointed to a domination of pyrogenically formed PAHs in the examined soils. The dominant PAHs in soil samples in urban zones were fluoranthene, benz[a]anthracene, phenanthrene and pyrene, mostly emitted from noncatalyst vehicles which are still in use in Serbia. The total carcinogenic potency for each sampling site was calculated. Regardless of the used carcinogenic activity factors, carcinogenic potency of 7 sites were 3–9 times higher than the reference ones indicating the increased carcinogenic burden of soils from these sites.     

Gas–particle concentration,distribution, and health risk assessment of polycyclic aromatic hydrocarbons at a traffic area of Giza,Egypt

Atmospheric particulate and gaseous polycyclic aromatic hydrocarbons (PAHs) samples were collected from an urban area in Dokki (Giza) during the summer of 2007 and the winter of 2007–2008. The average concentrations of PAHs were 1,429.74 ng/m³ in the particulate phase, 2,912.56 ng/m³ in the gaseous phase, and 4,342.30 ng/m³ in the particulate + gaseous phases during the period of study. Dokki has high level concentrations of PAH compounds compared with many polluted cities in the world. The concentrations of PAH compounds in the particulate and gaseous phases were higher in the winter and lower in the summer. Total concentrations of PAHs in the particulate phase and gaseous phase were 22.58% and 77.42% in summer and 36.97% and 63.03% in winter of the total (particulate + gaseous) concentrations of PAHs, respectively. The gaseous/particulate ratios of PAHs concentration were 3.43 in summer and 1.71 in winter. Significant negative correlation coefficients were found between the ambient temperature and concentrations of the total PAHs in the particulate and gaseous phases. The distribution of individual PAHs and different categories of PAHs based on aromatic ring number in the particulate and gaseous phases during the summer and winter were nearly similar, indicating similar emission sources of PAHs in both two seasons. Benzo(b)fluoranthene in the particulate phase and naphthalene in the gaseous phase were the most abundant compounds. Diagnostic concentration ratios of PAH compounds indicate that these compounds are emitted mainly from pyrogenic sources, mainly local vehicular exhaust emissions. Health risks associated with the inhalation of individual PAHs in particulate and gaseous phases were assessed on the basis of its benzo(a)pyrene equivalent concentration. Dibenzo(a,h)anthracene and benzo(a)pyrene in the particulate phase and benzo(a)pyrene and benzo(a)anthracene in the gaseous phase were the greatest contributors to the total health risks. The relative mean contributions of the total carcinogenic activity (concentrations) of all PAHs to the total concentrations of PAHs were 29.37% and 25.15% in the particulate phase and 0.76% and 0.92% in the gaseous phase during the summer and winter, respectively. These results suggest that PAHs in the particulate phase in the ambient air of Dokki may pose a potential health risk.     

九龙江龙岩段地表水中多环芳烃分布与污染源解析

用竹炭固相萃取恒波长同步荧光法测定了九龙江龙岩段水体中16种优控多环芳烃(PAHs)的含量。结果表明:龙岩市省控断面河水中2010年11月(冬季)多环芳烃的质量浓度为58.3×10-9~1 328.5×10-9g/L,平均为387.72×10-9g/L;2011年9月(秋季)水中总多环芳烃质量浓度为5.9×10-9~188.4×10-9g/L,平均为77.46×10-9g/L;7月(夏季)多环芳烃的质量浓度为16.7×10-9~1 203.3×10-9g/L,平均为475.05×10-9g/L,同国内外河流相比,九龙江龙岩段水体中PAHs污染较严重,且具有明显的季节分布特征。夏、秋、冬季九龙江龙岩段水体水中均以3~4环PAHs为主。污染来源分析表明,河水中PAHs主要来源于燃烧源。     

Interactions of Atmospheric Deposition with Coniferous Canopies in Estonia

Throughfall and open field bulk precipitation were measured at three coniferous sites during 1995–2002 in the framework of ICP Integrated Monitoring and at five coniferous sites during 1996–2002 in the framework of ICP Forests (Level II). The coniferous canopies acted as a sink for nitrate and ammonium and as a source for base cations: Ca²⁺, Mg²⁺ and K⁺. The estimated share of SO₄–S dry deposition from total deposition was 1.5–4 times higher for dormant period compared to growing period. During the study period average annual throughfall and bulk deposition of SO₄–S decreased significantly, 2.8 and 2.3 times, respectively. Throughfall enrichment with base cations increased in the order Mg < Na < Ca < K. Using Na as a tracer ion, average dry deposition and canopy leaching were calculated. Leaching was the dominant process for TF enrichment by potassium. Leaching of base cations occurred during growing as well as dormant period. The calculated internal flux of Ca²⁺ and Mg²⁺ varied in the range of 0.6–2.0 and 0.6–1.2 kg ha⁻¹ per year in spruce and pine stands, respectively. The internal circulation of K⁺ was significantly higher (8.9–10.9 kg ha⁻¹ per year) in spruce stands than in pine stands (2.7–4.4 kg ha⁻¹ per year).     

PAHs Contamination in Bank Sediment of the Yamuna River, Delhi, India

This study was performed to elucidate the distribution, concentration trend and possible sources of PAHs in bank sediment of river Yamuna in Delhi, India. The levels of 16 priority polycyclic aromatic hydrocarbons (PAHs) were analyzed during pre-monsoon, monsoon and post-monsoon seasons in the sediment fraction < 53 μm. Reference standards and internal standards were used for identification and quantification of PAHs by HPLC. The sum of 16 PAH compounds ranged from 4.50 to 23.53 μg/g with a mean concentration of 10.15 ± 4.32 μg/g (dry wt.). Among 5 sites studied, the site, Income Tax Office (ITO) was found to be the hotspot attaining highest concentration. Predominance of 2–4 ring PAHs suggests a relatively recent local sources of PAHs in the study area. Moreover, molecular indices based source apportionment also illustrates pyrogenic source fingerprint of PAHs. No significant temporal trend was observed.     

Measurement of particulate phase polycyclic aromatic hydrocarbon (PAHs) around a petroleum refinery

A study on concentrations of ambient particulates viz. total suspended particulate matters (TSP), respirable suspended particulate matter (RSPM) and polycyclic aromatic hydrocarbons (PAH) were carried out at six sites around the Asia’s largest, 12 MMTPA, petroleum refinery in west coast of India. PAH concentrations are correlated with each other in these sites, suggesting that they have related sources and sinks. The present article discusses the monitoring aspects such as sample collection, pretreatment and analytical methods and compares the monitored levels for assessing the source receptor distribution pattern. The main sources of RSPM and PAHs in urban air are automobile exhaust (CPCB, Polycyclic aromatic hydrocarbons (PAHs) in air and their effects on human health. “”, 2003; Manuel et al., Environmental Science and Technology, 13: 227–231, 2004) and industrial emissions like petroleum refinery (Vo-Dinh, Chemical analysis of polycyclic aromatic hydrocarbons, Wiley: New York, 1989; Wagrowaski and Hites, Environmental Science and Technology, 31: 279–282, 1997). Polycyclic aromatic hydrocarbons (PAH) are ubiquitous constituents of urban airborne particulate mostly generated by anthropogenic activities (Li et al., Environmental Science and Technology, 37:1958–2965, 2003; Thorsen et al., Environmental Science and Technology, 38: 2029–2037, 2004; Ohura et al., Environmental Science and Technology, 32: 450–455, 2004) and some of them are of major health concern mainly due to their well-known carcinogenic and mutagenic properties (Soclo et al., Marine Pollution Bulletin, 40: 387–396, 2000; Chen et al., Environment International, 28: 659–668, 2003; Larsen and Baker, Environmental Science and Technology, 32: 450–455, 2003). Limited information is available on PAHs contributions from refineries to ambient air. Hence this study would not only create a database but also provide necessary inputs towards dose-response relationship for fixing standards. Also, since it acts as precursor to green house gas, the data would be useful for climate change assessments. The objective of this article is to find out the concentration of PAHs in particulate matter around petroleum refinery and compare with their concentrations in major Indian urban centers.     

Determination of heavy metal pollution with environmental physicochemical parameters in waste water of Kocabas Stream (Biga, Canakkale, Turkey) by ICP-AES

Waste water pollution of industrial areas can answer for the serious consequences of one of the most important environmental threats to the future. In this study, inductively coupled plasma-atomic emission spectrometry method (ICP-AES) is proposed to determine heavy metals (Pb, Cu, Cd, Cr, Zn, Al, Fe, Ni, Co, Mn) and major elements (Ca, Mg) in waste water of Kocabas Stream. The concentration of metals in the waste water samples taken from 9 different stations (St.) in Biga-Kocabas Stream in November 2004 (autumn period) were determined after simple pretreatment of samples by the proposed ICP-AES method. An analysis of a given sample is completed in about 15 min for ICP-AES the method. The results of heavy metals concentrations in waste water were found between 0.00001–77.69610 mg l⁻¹ by the ICP-AES technique. The concentrations of Pb, Cd, Cu, Zn, Cr, Al, Fe, Mn, Ni, Co, Mg and Ca 0.00001 (St.3,6,7) – 0.0087 mg l⁻¹ (St.9), 0.00001 (St.4-7) – 0.0020 mg l⁻¹ (St.8), 0.00001 (St.1,3-7,9) – 0.0041 mg l⁻¹ (St.2), 0.0620 (St.2) – 0.2080 mg l⁻¹ (St.3), 0.0082 (St.6) – 0.2290 mg l⁻¹ (St.8), 0.3580 (St.2) – 1.7400 mg l⁻¹ (St.3), 0.2240 (St.1) – 0.6790 mg l⁻¹ (St.3), 0.0080 (St.1) – 1.5840 mg l⁻¹ (St.3), 0.0170 (St.3) – 0.0640 mg l⁻¹ (St.2), 0.0010 (St.1,4,5,8) – 0.0080 mg l⁻¹ (St.3), 5.0640 (St.9) – 5.2140 mg l⁻¹ (St.1) and 43.3600 (St.2) – 77.6961 mg l⁻¹ (St.9), respectively. Also we measured environmental physicochemical parameters such as temperature, salinity, specific conductivity, total dissolved solid (TDS), pH, oxidation and reduction potential (ORP), and dissolved oxygen (DO) in the waste water at sampling stations.     

Application of a Larval Medaka Assay to Evaluate the Fish Safety Level in Sagami River, Japan

Physico-chemical characteristics of some river and hand-dug well waters used for drinking and domestic purposes in the oil rich Niger Delta area of Nigeria were assessed using standard methods. The concentrations of the parameters in the river water samples ranged in the following order: pH (5.6–6.9), temperature (26.90–28.60°C), turbidity (23–63 NTU), electrical conductivity (52–184 μs/cm), DO (5.4–7.2 mg/l), BOD (21–57 mg/l), TDS (6.0–217 mg/l), PO₄ ³⁻ (0.19–1.72 mg/l), SO₄ ²⁻ (25–36.8 mg/l), NO₃ ⁻ (20.3–28 mg/l), Fe (6.07–15.71 mg/l), Zn (0.04–0.24 mg/l), Pb (0.01–0.17 mg/l), Ni (0.01–0.13 mg/l), Vn (0.01–0.20 mg/l) and Hg (0.001–0.002 mg/l). The concentrations of these parameters in the hand-dug well water ranged in the following order: pH (5.7–6.8) temperature (26–30°C), turbidity (134–171 NTU), electrical conductivity (160–340 μs/cm), DO (5.4–6.4 mg/l), BOD (13–34 mg/l), TDS (110–190 mg/l), PO₄ ³⁻ (0.84–1.84 mg/l), SO₄ ²⁻ (10.6–28.1 mg/l), NO₃ ⁻ (11.3–23 mg/l), Fe (13.17–16.31 mg/l), Ni (0.01–0.02 mg/l), Vn (0.01–0.04 mg/l) and Hg (0.001–0.004 mg/l). The concentrations of BOD, turbidity, NO₃ ⁻ and Fe in the water samples were above WHO and FMENV permissible limits for safe drinking water. The results suggest that the use of such waters for drinking and domestic purposes pose a serious threat to the health of the users and calls for the intervention of government agencies.     

The concentrations, distribution and sources of PAHs in agricultural soils and vegetables from Shunde, Guangdong, China

The concentrations, distribution and sources of 16 polycyclic aromatic hydrocarbons (PAHs) were determined in 30 agricultural soil and 16 vegetable samples collected from subtropical Shunde area, an important manufacturing center in China. The total PAHs ranged from 33.7 to 350 μg/kg in soils, and 82 to 1,258 μg/kg in vegetables. The most abundant individual PAHs are phenanthrene, fluoranthene, chrysene, pyrene and benzo(b)fluoranthene for soil samples, and anthracene, naphthalene, phenanthrene, pyrene and chrysene for vegetable samples. Average vegetable–soil ratios of total PAHs were 2.20 for leafy vegetables and 1.27 for fruity vegetables. Total PAHs in vegetable samples are not significantly correlated to those in corresponding soil samples. Principal component analyses were conducted to distinguish samples on basis of their distribution in each town, soil type and vegetable specie. Relatively abundant soil PAHs were found in town Jun’an, Beijiao, Chencun, Lecong and Ronggui, while abundant vegetable PAHs were observed in town Jun’an, Lecong, Xingtan, Daliang and Chenchun. The highest level of total PAHs were found in vegetable soil, followed by pond sediment and “stacked soil” on pond banks. The PAHs contents in leafy vegetables are higher than those in fruity vegetables. Some PAH compound ratios suggest the PAHs derived from incomplete combustion of petroleum, coal and refuse from power generation and ceramic manufacturing, and paint spraying on furniture, as well as sewage irrigation from textile industries. Soil PAHs contents have significant logarithmic correlation with total organic carbon, which demonstrates the importance of soil organic matter as sorbent to prevent losses of PAHs.     

Water quality assessment: surface water sources used for drinking and irrigation in Zaria,Nigeria are a public health hazard

We assessed the quality and pollution status of source surface waters in Zaria, Nigeria by monitoring the nature, cause and extent of pollution in Samaru stream, Kubanni River and Kubanni dam over a period of 10 months, between March and December 2002. A total of 228 water samples was collected from 12 sites and analysed for a total of ten physicochemical and one bacteriological quality indicators, using standard methods. Aesthetic water quality impairment parameters were also observed. The mean values of most water quality parameters were significantly higher (P < 0.05) in both the stream and river than in the dam. There was no significant correlation between faecal coliform counts (FCC) and water temperature (in the range 15–33°C); pH (5.77–7.32); and turbidity (1.4–567 NTU). The high FCC ranged from 2.0 × 10¹ to 1.6 × 10⁶ MPN/100 ml and exceeded the WHO standards for drinking water and water used for fresh-produce irrigation, and correlated positively (P < 0.05) with conductivity (in the range 68–1,029 μS/cm); TDS (10.0–70.0 mg/l); TSS (10.0–70.0 mg/l); Cl (7.5–181 mg/l); PO₄⁻P (0.01–0.41 mg/l); NO₃⁻N (0.6–3.8 mg/l) and BOD₅ (0.1–14.9 mg/l). The main pollution sources were municipal wastewater, stormwater runoffs, the ABU sewage treatment plant, abattoir effluents and irrigation farms treated with chemical fertilisers. We conclude that these water bodies are potentially hazardous to public health and that proper sewage treatment and river quality monitoring are needed to warn against hazards to public health.     

Temporal and Spatial Variation of Nutrient Levels in the Nemunas River (Lithuania and Belarus)

There are discordant results on trends in nutrient river water quality from the economical transition countries in Europe. The present study assessed the impact of these economical changes on the load and concentration at 17 monitoring stations along the Nemunas River and its major tributaries (Lithuania and Belarus). Three time periods were evaluated: the Soviet rule command system period 1986–1991, the transfer to market economy period 1992–1996 and the post reform period 1997–2002. The most surprising result in this study, was the increased area-specific load of NO₃-N from the first to the third period at almost all the sampling sites. The increase was particularly large (43–78%) at the sites in the Lithuanian part of the river. The corresponding load increase in the Belarussian part of the river was only 1–15%. The statistical analyses of concentration data confirm the strong upward NO₃-N trend at the Nemunas mouth and at 5 of the 6 tributaries in the lower part of Nemunas. Temporal and spatial analysis of nitrates transport in the Nemunas River and its main tributaries revealed that nitrates mainly originate from agricultural areas. The upward trends were most likely an effect of ploughing of pastures and unbalanced crop fertilisation in combination with large storage and accumulation of soil-nitrogen during the Soviet period.On contrary to nitrate-N, the area-specific load of PO₄-P decreased significantly from the first to the third period at all sites along the Nemunas River (31–86%). Seasonal (SMK) and Partial (PMK) Mann-Kendall tests on PO₄-P concentrations also showed significant downward trend at 14 of 16 investigated sites. The decrease of PO₄-P levels was attributed to the reduction of municipal and industrial point source emissions and to the decreased livestock numbers.The NH₄-N load showed the same pattern as PO₄-P. At the river mouth the load was 90 kg km⁻² yr⁻¹ during the first period compared to only 20–30 kg km⁻² yr⁻¹ in the third period. The trend test on NH₄-N concentrations detected significant downward trends at 5 out of 16 sites. The declines were explained by decreased emissions from cities and large animal breeding farms.This study showed that trend analysis at multiple sites in a river basin is crucial for the understanding of the variability in time and space. Such analysis is also important for our interpretation of underlying sources and fluxes in a drainage basin over time. This is particularly important for compounds that have different source origin.     

Assessment of water pollution in different bleaching based paper manufacturing and textile dyeing industries in India

Paper industries using different raw materials such as hard wood, bamboo, baggase, rice-straw and waste papers and bleaching chemicals like chlorine, hypochlorite, chlorine dioxide, hydrogen peroxide, sulphite and oxygen were studied to estimate organic pollution load and Adsorbable Organic Halides (AOX) per ton of production. The hard wood based paper industries generate higher Chemical Oxygen Demand (COD) loads (105–182 kg t⁻¹) and Biochemical Oxygen Demand (BOD) loads (32.0–72 kg t⁻¹) compared to the agro and waste paper based industrial effluents. The bleaching sequences such as C–EP–H–H, C–E–H–H, C–E–Do–D1 and O–Do–EOP–D1 are adopted in the paper industries and the molecular elemental chlorine free bleaching sequence discharges low AOX in the effluent. The range of AOX concentration in the final effluent from the paper industries was 0.08–0.99 kg t⁻¹ of production. Water consumption was in the range of 100–130 m³ t⁻¹ of paper production for wood based industries and 30–50 m³ for the waste paper based industries. Paper machine effluents are partially recycled after treatment and pulp mill black liquor are subject to chemical recovery after evaporation to reduce the water consumption and the total pollution loads. Hypochlorite bleaching units of textile bleaching processes generate more AOX (17.2–18.3 mg l⁻¹) and are consuming more water (45–80 l kg⁻¹) whereas alkali peroxide bleaching hardly generates the AOX in the effluents and water consumption was also comparatively less (40 l kg⁻¹ of yarn/cloth).     

Temperature Effect on Migration of Zn and Cd Through Natural Clay

To investigate the effect of temperature on effective diffusion coefficients and retardation factors for Zn and Cd, combined diffusion and sequential extraction analyses were conducted at 15 ^˚C and 55 ^˚C. The effective diffusion coefficients of the metals increased up to ten times according to the increased temperature. On the other hand, the effect of temperature on the retardation factor depended on the retention mechanisms of the metals. The distribution coefficient for Zn, which was mainly partitioned in the carbonate phase, increased up to two times with the increase in temperature. On the other hand, the distribution coefficient for Cd, which was mainly partitioned in the exchangeable phase, was hardly affected by the temperature change. Results of combined diffusion and sequential extraction analysis showed that the effect of temperature on the heavy metals’ (Zn and Cd) migration through the compacted natural clay was influenced by the combined effects of the diffusion coefficient and the retardation factor. Additionally, we could also observe the change in retention mechanism for the metals with the change in pore water concentration.