Quality control for sampling of PCDD/PCDF emissions from open combustion sources

Both long duration (>6 h) and high temperature (up to 139 °C) sampling efforts were conducted using ambient air sampling methods to determine if either high volume throughput or higher than ambient air sampling temperatures resulted in loss of target polychlorinated dibenzodioxins/dibenzofurans (PCDDs/PCDFs) from a polyurethane foam (PUF) sorbent. Emissions from open burning of simulated military forward operating base waste were sampled using EPA Method TO-9A for 185 min duration using a filter/PUF/PUF in series combination. After a 54 m³ sample was collected, the sampler was removed from the combustion source and the second PUF was replaced with a fresh, clean PUF. An additional 6 h of ambient air sampling (171 m³) was conducted and the second PUF was analyzed to determine if the PCDD/PCDF transferred from the filter and the first PUF. Less than 4.4% of the initial PCDD/PCDF was lost to the second PUF. To assess the potential for blow off of PCDD/PCDF analytes during open air sampling, the mobility of spiked mono- to hepta-PCDD/PCDF standards across a PUF sorbent was evaluated from ambient air temperatures to 145 °C with total volumes between 600 L and 2400 L. Lower molecular weight compounds and higher flow amounts increased release of the spiked standards consistent with vapor pressure values. At 600 L total sampled volume, the release temperature for 1% of the tetra-CDD (the lowest chlorinated homologue with a toxic compound) was 87 °C; increasing the volume fourfold reduced this temperature to 73 °C.     

A New Method for the Rapid Determination of Volatile Organic Compound Breakthrough Times for a Sorbent at Concentrations Relevant to Indoor Air Quality

Abstract

The use of sorbents has been proposed to remove volatile organic compounds (VOCs) present in ambient air at concentrations in the parts-per-billion (ppb) range, which is typical of indoor air quality applications. Sorbent materials, such as granular activated carbon and molecular sieves, are used to remove VOCs from gas streams in industrial applications, where VOC concentrations are typically in the parts-per-million range. A method for evaluating the VOC removal performance of sorbent materials using toluene concentrations in the ppb range is described. Breakthrough times for toluene at concentrations from 2 to 7500 ppb are presented for a hydrophobic molecular sieve at 25% relative humidity. By increasing the ratio of challenge gas flow rate to the mass of the sorbent bed and decreasing both the mass of sorbent in the bed and the sorbent particle size, this method reduces the required experimental times by a factor of up to several hundred compared with the proposed American Society of Heating, Refrigerating, and Air-Conditioning Engineers method, ASHRAE 145P, making sorbent performance evaluation for ppb-range VOC removal more convenient. The method can be applied to screen sorbent materials for application in the removal of VOCs from indoor air.     

A new method for the rapid determination of volatile organic compound breakthrough times for a sorbent at concentrations relevant to indoor air quality

The use of sorbents has been proposed to remove volatile organic compounds (VOCs) present in ambient air at concentrations in the parts-per-billion (ppb) range, which is typical of indoor air quality applications. Sorbent materials, such as granular activated carbon and molecular sieves, are used to remove VOCs from gas streams in industrial applications, where VOC concentrations are typically in the parts-per-million range. A method for evaluating the VOC removal performance of sorbent materials using toluene concentrations in the ppb range is described. Breakthrough times for toluene at concentrations from 2 to 7500 ppb are presented for a hydrophobic molecular sieve at 25%) relative humidity. By increasing the ratio of challenge gas flow rate to the mass of the sorbent bed and decreasing both the mass of sorbent in the bed and the sorbent particle size, this method reduces the required experimental times by a factor of up to several hundred compared with the proposed American Society of Heating, Refrigerating, and Air-Conditioning Engineers method, ASHRAE 145P, making sorbent performance evaluation for ppb-range VOC removal more convenient. The method can be applied to screen sorbent materials for application in the removal of VOCs from indoor air.     

Detection and quantification of 2-methyltetrols in ambient aerosol in the southeastern United States

Filters collected from the Southeastern Aerosol Research and Characterization (SEARCH) air monitoring network were analyzed for the presence of 2-methyltetrols, namely 2-methylthreitol and 2-methylerythritol, two compounds that are products of the photooxidation of isoprene and have been detected in aerosol at a variety of sites around the globe. The 2-methytetrols were detected in ambient filter samples collected at the four SEARCH sites, Birmingham, AL, Centreville, AL, Pensacola, FL, and at Jefferson Street in Atlanta, GA, in late June 2004. Average atmospheric concentrations of 11.9 and 4.8 ng m⁻³ were measured for 2-methylerythritol and 2-methylthreitol, respectively, at the inland sampling sites, whereas average concentrations of 4.9 and 1.6 ng m⁻³ were measured at the coastal sampling location (Pensacola). On average, the aerosol loading from these two compounds accounts for approximately 0.42% and 0.21% of the organic mass collected on a given sampling day at the inland and coastal sites, respectively. The present data on these compounds, which are particulate-phase fingerprints of isoprene photooxidation, add to the growing body of ambient data on secondary organic aerosol from isoprene.     

Characteristic Study of Ambient Air Total Gaseous Mercury (TGM) Concentrations During Rainy and Non-Rainy Periods at a Traffic Site in Taiwan

This investigation studied the concentrations of ambient air total gaseous mercury (TGM) during the rainy periods at the Hung-Kuang traffic sampling site in central Taiwan from May 26 to June 16, 2014. The results were compared with those of a previous study for ambient air TGM during non-rainy daytime and nighttime periods at the Hung-Kuang traffic sampling site, which was conducted during March 21 to July 20, 2012. The observed mean concentration of ambient air TGM was 1.16 ng/m³ during the rainy periods at the Hung-Kuang traffic sampling site. The mean ambient air TGM concentrations were higher in the non-rainy sampling period in daytime than in the rainy sampling period from this study. The mean ratio of non-rainy sampling period in daytime to that of rainy sampling period for ambient air TGM were 3.15. Furthermore, the mean ambient air TGM concentrations were higher in the non-rainy sampling period in nighttime in than in the rainy sampling period for this study. The mean rations for non-rainy sampling period in nighttime to that of the rainy sampling period for ambient air TGM were 2.70. The results obtained in this study also revealed that the ambient air TGM concentrations during the rainy period had the lowest concentrations when compared with the other sampling sites in other world regions.     

Air toxics in Canada measured by the National Air Pollution Surveillance (NAPS) program and their relation to ambient air quality guidelines

This study reports ambient concentrations of 63 air toxics that were measured in Canada by the National Air Pollution Surveillance (NAPS) program over the period 2009–2013. Measured concentrations are compared with ambient air quality guidelines from Canadian jurisdictions, and compounds that exceeded guidelines are identified and discussed. Although this study does not assess risk or cumulative effects, air toxics that approached guidelines are also identified so that their potential contribution to ambient air toxics pollution can be considered. Eleven air toxics exceeded at least one guideline, and an additional 16 approached guidelines during the study period. Four compounds were measured using methods whose detection limits exceeded a guideline value, three of which could not be compared with guidelines, since they were not detected in any samples. The assessment of several metal(loid) concentrations is tentative, since they were measured only in fine particulate matter (PM) but compared with guidelines based on coarse or total PM. Improvements to sampling and analysis techniques for the latter compounds as well as for those whose methods are subject to known uncertainties would improve confidence in reported concentrations and their relation to applicable guidelines. Analysis of sampling strategies for all compounds found to exceed or approach guidelines would contribute to ensuring that their spatiotemporal coverage is adequate. Examination of the air toxics not measured by NAPS but having guidelines in Canadian jurisdictions or being included in other programs such as the U.S. National-Scale Air Toxics Assessment (NATA) would contribute to ensuring that the full suite of pollutants relevant to ambient air quality in Canada is subject to adequate study. The results of this study can be applied to evaluating the effectiveness of toxic substances management in Canada.

Implications: Recent measurements of 63 air toxics in Canada by the National Air Pollution Surveillance (NAPS) program showed that 11 compounds exceeded daily or annual ambient air quality guidelines and that an additional 16 compounds approached such guidelines within an order of magnitude. The results of this study can be applied to evaluating the effectiveness of toxic substances management in Canada and to identifying compounds that merit further investigation.     

Polycyclic organic material (POM) in urban air. Fractionation,chemical analysis and genotoxicity of particulate and vapour phases in an industrial town in Finland

Polycyclic organic material (POM) was collected by high-volume sampling on filter and on XAD-2 resin from the air of a small industrial town in Finland. Concurrent chemical analysis and the assays for genotoxic activity were performed on the particulate and the vapour phases of ambient air POM and their chemical fractions. Furthermore, correlations between seasonal meteorological parameters and POM concentrations were studied to reveal characteristic POM profiles for various emission sources. The range of total POM concentrations varied from 115 to 380 ng m⁻³ in late spring and from 17 to 83 ng m⁻³ in early winter. No direct correlation of ambient POM was seen with the temperature, but rather with the wind direction from various emission sources. Especially the low molecular weight compounds were associated with wind direction from industrial sources. Genotoxic activity, as detected by the Ames Salmonella/microsome test and the SCE assay in CHO cells, was found not only in the paniculate phase samples but also in the vapour phase. The polar fractions of some of the samples showed genotoxic activity, and also direct mutagenicity was observed with both the assay systems; these facts support the significance of compounds other than conventional polycyclic aromatic hydrocarbons (PAH) in the samples.     

Polycyclic aromatic hydrocarbons in ambient air in the Philippines derived from passive sampler with polyurethane foam disk

Passive samplers with polyurethane disks (PUF) were applied in the determination of the concentration of polycyclic aromatic hydrocarbons (PAHs) in ambient air in six residential areas in the Philippines during four simultaneous sampling periods. The uptake profiles of PAHs were determined at one site during one sampling period. Most of the PAHs that were detected in air at concentrations that were significantly higher than their analytical detection limits exhibited a linear uptake trend on the PUF disk. The linear uptake profiles of some high molecular weight (HMW) PAHs were not established and this is attributed to the low concentration of the compounds in air in the gaseous phase. The retention concentrations of phenanthrene-d-10 were determined after depuration in four sampling sites during two sampling periods. The sampling rate for phenanthrene-d-10 was calculated at the linear phase of the uptake using the k_A derived from depuration experiments and the relationship of k_A and sampling rate which was established in a previous passive sampling study. The average sampling rate obtained for phenanthrene d-10 (2.94±0.69 m³ d⁻¹) was applied for derivation of the concentrations of the PAHs in the field samples.The passive sampler with PUF disk and short integration time of 42–56 days is applicable for the derivation of the concentrations of PAHs in ambient air in the Philippines. The concentrations of the organic pollutants derived from the passive sampler showed variability for the six residential areas; reflecting the influence of possible sources of emission of the pollutants at the sites at the different sampling periods. The weather conditions, including the occurrence of a tropical cyclone, increased rainfall and high-relative humidity during the rainy season, had an influence on the concentrations of PAHs derived by the passive sampler.     

Problems in the sampling and analysis of carbon particulate

Several thermal and wet chemical methods of separating organic from elemental carbon in particulate samples were examined. It is concluded that none of them represents an ideal separation procedure and that only a method-dependent operational definition of organic and elemental carbon is possible at this time. The best separation method appears to be a thermal procedure using 350°C air oxidation followed by pyrolysis in He at 950°C. There are also difficulties in sampling since dual filter techniques show that adsorption of organic compounds on various filter media accounted for at least 15 per cent of the total organic carbon collected during ambient sampling in Warren, MI. This adsorption further confuses the results and needs to be studied at other sampling sites.     

PCDDs/PCDFs in ambient air (<1 fg m(-3)) - the CTDEP long term sampling (30 d) method

The Connecticut Department of Environmental Protection (CTDEP) commenced monitoring for PCDDs/PCDFs (polychlorinated dibenzodioxins and polychlorinated dibenzofurans) in ambient air in 1987 and adopted the long term (30 d) sampling approach in 1993. The CTDEP method represents the first use of isotopically labeled PCDDs/PCDFs as field surrogates to monitor the behavior of native PCDDs/PCDFs present in actual ambient air samples. This feature first introduced in 1987 was later adopted by US EPA in revisions to sampling methods for PCDDs/PCDFs in ambient air (EPA Method TO9A) as well as development of EPA Reference Method 23 for measurement of PCDDs/PCFDs in stationary source emissions. Results are provided here for a total of twenty-three (23) samples (reported as pairs) representing twelve (12) 30 d sampling events conducted at a site located in metropolitan Hartford CT. Samples were collected in winter months during calendar years 2002-2008. PCDDs/PCDFs concentration data (pg m⁻³) are reported as both congener sums (Cl₄-Cl₈) and 2378-substitued congeners. Total PCDDs/PCDFs concentrations for these twelve (12) sampling events ranged from 0.68 pg m⁻³ (2003) to 4.18 pg m⁻³ (2004) with a mean concentration of 2.04 pg m⁻³.Method performance was monitored through use of collocated samples, in field isotopically labeled compounds, isotopically labeled laboratory applied internal standards and field blank samples. Method performance consistently exceeded goals established in USEPA Method TO9A for these same parameters. Average recoveries of in field labeled PCDDs/PCDFs ranged from 97.5% to 104.2%. Average (mean) recoveries for each of the ten (10) isotopically labeled internal standards ranged from 77.0% (¹³C-OCDF) to 95.5% (¹³C-2,3,7,8-TCDF). Method precision defined as % RPD data for collocated sampler pairs ranged from 8% to 14% for PCDDs and from 5% to 12% for PCDFs. The mean RPD for all PCDDs/PCDFs combined is 9.6%. Field monitoring results demonstrate method sensitivity for all PCDDs/PCDFs congeners and 2378-substituted congeners to be well below concentrations typically found for these compounds in ambient air (all reported data represent measured concentrations). Quantities (pg) found in field blanks represent the major determinant to achieving further enhancements in method sensitivity for selected congeners (OCDD < 42 fg m⁻³; 1,2,3,4,6,7,8-HpCDD < 5.7 fg m⁻³; and 1,2,3,4,6,7,8-HpCDF < 2.1 fg m⁻³). The CTDEP method represents a highly sensitive and reliable technique for monitoring of PCDDs/PCDFs congeners and other persistent organic pollutants (POPs) at ultra trace levels in ambient air (fg m⁻³).     

Use of thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) on identification of odorant emission focus by volatile organic compounds characterisation

Volatile organic compounds (VOCs) from several different municipal solid wastes’ treatment plants in Mallorca (Spain) have been analysed by thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS). Ambient (immission) air was collected during February and March 2011 by active sampling onto sorbents Tenax™ TA and Carboxen™ 1000. The study presents the chemical characterisation of 93 volatile organic compounds (VOCs) from an overall set of 84 immission air samples. 70 VOCs were positively identified.The linear fit for all 93 external standard calibration, from 10 mg L⁻¹ to 150 mg L⁻¹ (n = 4), was within the range 0.974 < r² < 0.998. Limits of detection of the method (LOD) for all the standards were within the range 1.1-4,213 pg, as the absolute standard amount spiked into sorbent tubes in 1 μL standard mixture (dissolved in methanol).Overall results stated systematic correlation between waste’s nature and VOCs’ air composition. Organic wastes show main contribution of terpenes, waste water sludge residues’ of reduced sulphured compounds (RSCs) and municipal solid wastes show contribution of a wide sort of VOCs. The use of a chemometric approach for variable’s reduction to 12 principal components enables evaluation of similarities and dissimilarities between facilities. PCA clearly related samples to its corresponding facility on the basis of their VOCs composition and the ambient temperature.     

Volatile organic compounds in the atmosphere of forests

The procedure of sampling and gas chromatographic-mass spectrometric analysis of air containing volatile emissions from living plants has been elaborated. The qualitative composition of volatile organic compounds (VOC) produced by 22 species of plants which are characteristic for Northern hemisphere forests has been studied. The emission rate of isoprene and terpenes for some of them has been determined. Terpene concentrations in coniferous forests of different regions of the U.S.S.R. have been also determined. The list of compounds identified includes more than 70 substances of different classes. Total terpene concentrations in the coniferous forests air usually vary from 3.5 to 35 μg⁻³. Strong influence of meteorological conditions on the emission rate and terpene concentrations in the air under the forest canopy has been noted.     

Analysis of gaseous diisocyanates in air using chemosorption sampling

A sampling procedure for 2,4- and 2,6-toluenediisocyanate (TDI) and 4,4′-diphenylmethane diisocyanate (MDI) in the range 0.007-0.7 mg/m³ in a 15 L air sample is described. The sampling is performed with 9-(N-methylaminomethyl)-anthracene (MAMA) adsorbed on a solid sorbent, Amberlite XAD-2. The recoveries are 80–100% in this chemosorption reaction. The urea derivatives are desorbed with N,N-dimethylformamide and analysed by high performance liquid chromatography (HPLC). Samples and prepared chemosorption tubes are stable for at least two weeks if stored in the dark. To complete the investigation, field measurements of TDI were performed in an industrial atmosphere.     

Testing of a sampling system and analytical method for determination of semivolatile organic compounds in ambient air

A sampling system and analytical procedure for determining PCDD/Fs, PCBs, HCB, and PAHs in ambient air was tested. The reproducibility of the concentrations and the gas/particle partitioning was ± 10% for most compounds. The removal of gaseous compounds on the XAD resin trap was greater than 99%. The adsorption of gaseous substances on the glass fiber filter was negligible for compounds primarily found in the gas phase, but could not be ruled out for compounds found mainly on particles.     

Influence of a large steel complex on the spatial distribution of volatile polycyclic aromatic hydrocarbons (PAHs) determined by passive air sampling using membrane-enclosed copolymer (MECOP)

Membrane-enclosed copolymer (MECOPs) samplers containing crystalline copolymers of ethylvinylbenzene-divinylbenzene in polyethylene membranes were used to assess the influence of a steel complex on the level and spatial distribution of polycyclic aromatic hydrocarbons (PAHs) in ambient air. MECOPs were deployed at six sites in Pohang, Korea for 37 days (August 9, 2005–September 14, 2005). Fluorene, phenanthrene, anthracene, and fluoranthene were dominant PAHs with the highest contribution of phenanthrene (59%) to the total amount of vapor-phase PAHs. The spatial distribution of total PAHs in the vapor phase ranging from 76 to 1077 ng MECOP⁻¹ and air dispersion modeling suggested that the steel complex was the major PAH source in Pohang. It was revealed that the major wind directions rather than the distance from the steel complex were a significant factor affecting the levels of PAHs at the sampling sites. Finally, we tried to convert MECOP concentrations (ng MECOP⁻¹) to air concentrations (ng m⁻³) with the modified sampling rates (m³ day⁻¹). This study demonstrates again that passive air samplers are useful tools for spatially resolved and time-integrated monitoring of semivolatile organic compounds (SOCs) in ambient air.     

Theoretical versus Observed Gas-Particle Partitioning of Carbonyl Emissions from Motor Vehicles

Abstract

A state-of-the-science thermodynamic model describing gas-particle absorption processes was used to predict the gas-particle partitioning of mixtures of approximately 60 carbonyl compounds emitted from low-emission gasoline-powered vehicles, three-way catalyst gasoline-powered vehicles, heavy-duty diesel vehicles under the idle-creep condition (HDDV idle), and heavy-duty diesel vehicles under the five-mode test (HDDV 5-mode). Exhaust was diluted by a factor of 120–580 with a residence time of approximately 43 sec. The predicted equilibrium absorption partitioning coefficients differed from the measured partitioning coefficients by several orders of magnitude. Time scales to reach equilibrium in the dilution sampling system were close to the actual residence time during the HDDV 5-mode test and much longer than the actual residence time during the other vehicle tests. It appears that insufficient residence time in the sampling system cannot uniformly explain the failure of the absorption mechanism to explain the measured partitioning. Other gas-particle partitioning mechanisms (e.g., heterogeneous reactions, capillary adsorption) beyond the simple absorption theory are needed to explain the discrepancy between calculated carbonyl partitioning coefficients and observed partitioning. Both of these alternative partitioning mechanisms imply great challenges for the measurement and modeling of semi-volatile primary organic aerosol (POA) species from motor vehicles. Furthermore, as emitted particle concentrations from newer vehicles approach atmospheric background levels, dilution sampling systems must fundamentally change their approach so that they use realistic particle concentrations in the dilution air to approximately represent real-world conditions. Samples collected with particle-free dilution air yielding total particulate matter concentrations below typical ambient concentrations will not provide a realistic picture of partitioning for semi-volatile compounds.     

Predicting residential indoor concentrations of nitrogen dioxide,fine particulate matter,and elemental carbon using questionnaire and geographic information system based data

Previous studies have identified associations between traffic-related air pollution and adverse health effects. Most have used measurements from a few central ambient monitors and/or some measure of traffic as indicators of exposure, disregarding spatial variability and factors influencing personal exposure-ambient concentration relationships. This study seeks to utilize publicly available data (i.e., central site monitors, geographic information system, and property assessment data) and questionnaire responses to predict residential indoor concentrations of traffic-related air pollutants for lower socioeconomic status (SES) urban households.As part of a prospective birth cohort study in urban Boston, we collected indoor and outdoor 3–4 day samples of nitrogen dioxide (NO₂) and fine particulate matter (PM_2.5) in 43 low SES residences across multiple seasons from 2003 to 2005. Elemental carbon (EC) concentrations were determined via reflectance analysis. Multiple traffic indicators were derived using Massachusetts Highway Department data and traffic counts collected outside sampling homes. Home characteristics and occupant behaviors were collected via a standardized questionnaire. Additional housing information was collected through property tax records, and ambient concentrations were collected from a centrally located ambient monitor.The contributions of ambient concentrations, local traffic and indoor sources to indoor concentrations were quantified with regression analyses. PM_2.5 was influenced less by local traffic but had significant indoor sources, while EC was associated with traffic and NO₂ with both traffic and indoor sources. Comparing models based on covariate selection using p-values or a Bayesian approach yielded similar results, with traffic density within a 50 m buffer of a home and distance from a truck route as important contributors to indoor levels of NO₂ and EC, respectively. The Bayesian approach also highlighted the uncertanity in the models. We conclude that by utilizing public databases and focused questionnaire data we can identify important predictors of indoor concentrations for multiple air pollutants in a high-risk population.     

Assessment of the emission of PCDD/Fs and dioxin-like PCBs from an industrial area over a nearby town using a selective wind direction sampling device

The development of new sampling devices or strategies to assess the concentration of persistent organic pollutants (POPs) in the environment has increased in the last two decades. In this study, a selective sampling device was used to evaluate the impact of potential local sources of polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/Fs) and dioxin-like polychlorinated biphenyl (dl-PCBs) emissions on the ambient air levels of such compounds in a town near an important industrial estate. Average concentrations of target compounds of up to 2.5 times for PCDD/Fs and 2 times for dl-PCBs were found to come from the industrial state confirming this area as the main responsible for the majority of such compounds reaching the town.This finding was supported by a PCDD/F and dl-PCB sample profile analysis and a principal component analysis (PCA), which established a direct link between the dioxin-like compounds found in the samples collected in the town and their source.     

Simultaneous sampling of NH3, HNO3, HC1, SO2 and H2O2 in ambient air by a wet annular denuder system

A new sampling device is described for the simultaneous collection of NH₃, HNO₃, HCl, SO₂ and H₂O₂ in ambient air. The apparatus is based on air sampling by two parallel annular denuder tubes. The gases are collected by absorption in solutions present in the annulus of the denuder tubes. After a sampling time of 30 min at flow rate of 32 ℓ min⁻¹ the solutions are extracted from the denuders and analyzed off-line. The detection limits of NH₃, HNO₃, HCL and SO₂ are in the order of 0.1–0.5 μm⁻³. For H₂O₂ the detection limit is 0.01 μm⁻³. The reproducibility is 5–10% at the level of ambient air concentrations. Comparison of this novel technique with existing methods gives satisfactory results. The compact set-up offers the possibility of field experiments without the need of extensive equipment.     

Evaluation of the Use of Diffusive Air Samplers for Determining Temporal and Spatial Variation of Volatile Organic Compounds in the Ambient Air of Urban Communities

Abstract

The Houston-Galveston metropolitan area has a relatively high density of point and mobile sources of air toxics, and determining and understanding the relationship between emissions and ambient air concentrations of air toxics is important for evaluating potential impacts on public health and formulating effective regulatory policies to control this impact, both in this region and elsewhere. However, conventional ambient air monitoring approaches are limited with regard to expense, siting limitations, and representative sampling necessary for adequate exposure assessment. The overall goal of this multiphase study is to evaluate the use of simple passive air samplers to determine temporal and spatial variability of the ambient air concentrations of selected volatile organic compounds (VOCs) in urban areas. Phase 1 of this study, reported here, was a field evaluation of 3M organic vapor monitors (OVMs) involving limited comparisons with commonly used active sampling methods, an assessment of sampler precision, a determination of optimal sampling duration, and an investigation of the utility of a simple modification of the commercial sampler. The results indicated that a sampling duration of 72 hr exhibited generally low bias relative to automated continuous gas chromatography measurements, good overall precision, and an acceptable number of measurements above detection limits. The modified sampler showed good correlation with the commercial sampler, with higher sampling rates, although lower than expected.