Airborne bacterial reduction by spraying slightly acidic electrolyzed water in a laying-hen house

Spraying slightly acidic electrolyzed water (SAEW) has been considered as a potential approach to reduce airborne bacteria in laying-hen houses. In this study, the effects of spraying SAEW on airborne bacterial reduction were investigated in a laying-hen house as compared with using diluted didecyl dimethyl ammonium bromide (DDAB). Averaged air temperature reduced by approximate 1 °C and average relative humidity increased by 3% at a stable ventilation rate (about 2.5 m³ hr^?1 per bird) in the laying-hen house 30 min after spraying (120 mL m^?2). Compared with the control without spraying, the airborne bacterial concentration was reduced by about 0.70 and 0.37 log₁₀ colony-forming units (CFU) m^?3 in the 4 hr after spraying 120 mL m^?2 SAEW (available chlorine concentration [ACC] of 156 mg L^?1) and diluted DDAB (active compound concentration of 167 mg L^?1), respectively. Compared with spraying diluted DDAB, spraying SAEW was determined to be more effective for reducing airborne bacterial in laying-hen houses. The effects of spraying SAEW and diluted DDAB on airborne bacterial reduction in the laying-hen house increased with the increasing available chlorine concentrations for SAEW (156, 206, 262 mg L^?1) and increasing active compound concentrations for diluted DDAB (167, 333, 500 mg L^?1), respectively. Spraying SAEW and diluted DDAB with two levels of spraying volumes (120 and 90 mL m^?2) both showed significant differences on airborne bacterial reduction in the laying-hen house (P < 0.05).

Implications: It is difficult to effectively reduce airborne bacteria in laying-hen houses. This work describes the application of spraying slightly acidic electrolyzed water as a new approach for reducing airborne bacteria in a laying-hen house. The effects of active compound concentrations and spray volumes on the airborne bacterial reductions by spraying SAEW were also investigated. This study provided a new effective and environmentally friendly approach to reduce the airborne bacteria in poultry houses, contributing to bird housing environment management and improving bird health.     

Optimization of a wet scrubber with electrolyzed water spray—Part II: Airborne culturable bacteria removal

Airborne microorganisms, especially the pathogenic microorganisms, emitted from animal feeding operations (AFOs) may harm the environment and public health and threaten the biosecurity of the farm and surrounding environment. Electrolyzed water (EW), which was considered to be an environmentally friendly disinfectant, may be a potential spraying medium of wet scrubber for airborne microorganism emission reduction. A laboratory test was conducted to investigate the airborne bacteria (CB) removal efficiency of the wet scrubber by EW spray with different designs and operating parameters. Both the available choline (AC) initial loss rate and AC traveling loss rate of acidic electrolyzed water (AEW; pH = 1.35) were much higher than those of slightly acidic electrolyzed water (SAEW; pH = 5.50). Using one spraying stage with 4 m sec^?1 air speed in the duct, the no detect lines (NDLs) of SAEW (pH = 5.50) for airborne Escherichia coli, Staphylococcus aureus, and Salmonella enteritidis removal were all 50 mg L^?1, whereas the NDLs of AEW (pH = 1.35) for airborne E. coli, S. aureus, and S. enteritidis removal increased to 70, 90, and 90 mg L^?1, respectively. The NDLs of SAEW (pH = 5.50) for airborne E. coli, S. aureus, and S. enteritidis were lower than those of AEW (pH = 1.35) at single spraying stage. Increase in the number of stages lowered the NDLs of both SAEW (pH = 5.50) and AEW (pH = 1.35) for airborne E. coli, S. aureus, and S. enteritidis. EW with a higher available chlorine concentration (ACC) was needed at air speed of 6 m sec^?1 to reach the same airborne CB removal efficiency as that at air speed of 4 m sec^?1. The results of this study demonstrated that EW spray wet scrubbers could be a very effective and feasible airborne CB mitigation technology for AFOs.

Implications: It is difficult to effectively reduce airborne bacteria emitted from animal feeding operations (AFOs). Electrolyzed water (EW) with disinfection effect and acidity is a potential absorbent for spray in wet scrubber to remove microorganisms and ammonia. Based on the field test results, a laboratory experiment we conducted this time was to optimize the design and operation parameters to improve the airborne bacteria removal efficiency. A better understanding of the EW application in the wet scrubber can contribute to the mitigation of airborne bacteria from animal houses and improve the atmosphere air quality.     

Microbial structure and chemical components of aerosols caused by rotating brushes in a wastewater treatment plant

Purpose

Bacterial community structure and the chemical components in aerosols caused by rotating brushes in an Orbal oxidation ditch were assessed in a Beijing municipal wastewater treatment plant.

Methods

Air samples were collected at different distances from the aerosol-generating rotating brushes. Molecular culture-independent methods were used to characterize the community structure of the airborne bacteria in each sample regardless of cell culturability. A clone library of 16S rDNA directly amplified from air DNA of each sample was constructed and sequenced to analyze the community composition and diversity. Insoluble particles and water-soluble ions emitted with microorganisms in aerosols were analysis by a scanning electron microscope together with energy dispersive X-ray spectroscopy and ion chromatogram analyzer.

Results

In total, most of the identified bacteria were Proteobacteria. The majority of sequences near the rotating brushes (the main source of the bioaerosols) were Proteobacteria (62.97 %) with ??-(18.52 %) and ??-(44.45?%) subgroups and Bacteroidetes (29.63 %). Complex patterns were observed for each sampling location, suggesting a highly diverse community structure, comparable to that found in water in the Orbal oxidation ditch. Accompany with microorganisms, 46.36???g/m³ of SO ₄ ^2? , 29.35???g/m³ of Cl^?, 21.51???g/m³ of NO ₃ ^? , 19.76???g/m³ of NH ₄ ⁺ , 11.42???g/m³ of PO ₄ ^3? , 6.18???g/m³ of NO ₂ ^? , and elements of Mg, Cl, K, Na, Fe, S, and P were detected from the air near the aerosols source.

Conclusions

Differences in the structure of the bacterial communities and chemical components in the aerosols observed between sampling sites indicated important site-related variability. The composition of microorganisms in water was one of the most important sources of bacterial communities in bioaerosols. Chemical components in bioaerosols may provide a media for airborne microorganism attachment, as well as a suitable microenvironment for their growth and survival in the air. This study will be benefit for the formulation of pollution standards, especially for aerosols, that take into account plant workers?? health.     

1-Butanol Removal from a Contaminated Airstream under Continuous and Diurnal Loading Conditions

Abstract

A polysulfone microporous membrane module was investigated for control of 1-butanol-contaminated gas streams. A diurnal loading condition, using two different butanol concentrations, was used to simulate startup and stop conditions associated with shift work. The membrane module was also used to remove 1-butanol from air under continuous loading conditions in a bioreactor. The reactors were seeded with a mixed bacterial consortium capable of butanol biodegradation. Biokinetic parameters for butanol utilization were determined for the culture to be a maximum specific utilization rate (k) equal to 4.3 d^?1 and a half saturation constant (K_s) equal to 8.9 mg L^?1. A biofilter running only with diurnal loading conditions giving a “40-hr workweek” had an average 1-butanol removal rate of 29% (111 ppm, 74 gm^?3 hr^?1) from a 350-ppm influent at the end of an 8-hr operational day. End-of-day removal varied between 4 and 67% during the operational period. With continuous steady-state operation followed by placement on a diurnal loading schedule and influent butanol concentrations increased to 700 ppm, butanol removal averaged 38% (269 ppm, 145 gm^?3 hr^?1). Under continuous loading, steady-state conditions, 1-butanol removal from the airstream was greater than 99% (200 ppm, 73 gm^?3 hr^?1). These results suggest that the bioreactor can be operated on a diurnal schedule or 40-hr week operational schedule without any decline in performance.     

Effects of Ceiling-Mounted HEPA-UV Air Filters on Airborne Bacteria Concentrations in an Indoor Therapy Pool Building

Abstract

The purpose of this study was to assess the effectiveness of a new generation of high-volume, ceiling-mounted high-efficiency particulate air (HEPA)-ultraviolet (UV) air filters (HUVAFs) for their ability to remove or inactivate bacterial aerosol. In an environmentally controlled full-scale laboratory chamber (87 m³), and an indoor therapy pool building, the mitigation ability of air filters was assessed by comparing concentrations of total bacteria, culturable bacteria, and airborne endotoxin with and without the air filters operating under otherwise similar conditions. Controlled chamber tests with pure cultures of aerosolized Mycobacterium parafortuitum cells showed that the HUVAF unit tested provided an equivalent air-exchange rate of 11 hr^?1. Using this equivalent air-exchange rate as a design basis, three HUVAFs were installed in an indoor therapy pool building for bioaerosol mitigation, and their effectiveness was studied over a 2-year period. The HUVAFs reduced concentrations of culturable bacteria by 69 and 80% during monitoring periods executed in respective years. The HUVAFs reduced concentrations of total bacteria by 12 and 76% during the same monitoring period, respectively. Airborne endotoxin concentrations were not affected by the HUVAF operation.     

Slightly acidic electrolyzed water for reducing airborne microorganisms in a layer breeding house

Reducing airborne microorganisms may potentially improve the environment in layer breeding houses. The effectiveness of slightly acidic electrolyzed water (SAEW; pH 5.29–6.30) in reducing airborne microorganisms was investigated in a commercial layer house in northern China. The building had a tunnel-ventilation system, with an evaporative cooling. The experimental area was divided into five zones along the length of the house, with zone 1 nearest to an evaporative cooling pad and zone 5 nearest to the fans. The air temperature, relative humidity, dust concentration, and microbial population were measured at the sampling points in the five zones during the study period. The SAEW was sprayed by workers in the whole house. A six-stage air microbial sampler was used to measure airborne microbial population. Results showed that the population of airborne bacteria and fungi were sharply reduced by 0.71 × 10⁵ and 2.82 × 10³ colony-forming units (CFU) m^?3 after 30 min exposure to SAEW, respectively. Compared with the benzalkonium chloride (BC) solution and povidone-iodine (PVP-I) solution treatments, the population reductions of airborne fungi treated by SAEW were significantly (P < 0.05) more, even though the three disinfectants can decrease both the airborne bacteria and fungi significantly (P < 0.05) 30 min after spraying.

Implications: There are no effective methods for reducing airborne microbial levels in tunnel-ventilated layer breeding houses; additionally, there is limited information available on airborne microorganism distribution. This research investigated the spatial distribution of microbial population, and the effectiveness of spraying slightly acidic electrolyzed water in reducing microbial levels. The research revealed that slightly acidic electrolyzed water spray was a potential method for reducing microbial presence in layer houses. The knowledge gained in this research about the microbial population variations in the building may assist producers in managing the bird housing environment and engineers in designing poultry houses.     

Whole House Particle Removal and Clean Air Delivery Rates for In-Duct and Portable Ventilation Systems

Abstract

A novel method for determining whole house particle removal and clean air delivery rates attributable to central and portable ventilation/air cleaning systems is described. The method is used to characterize total and air-cleaner-specific particle removal rates during operation of four in-duct air cleaners and two portable air-cleaning devices in a fully instrumented test home. Operation of in-duct and portable air cleaners typically increased particle removal rates over the baseline rates determined in the absence of operating a central fan or an indoor air cleaner. Removal rates of 0.3- to 0.5-μm particles ranged from 1.5 hr^?1 during operation of an in-duct, 5-in. pleated media filter to 7.2 hr^?1 for an in-duct electrostatic air cleaner in comparison to a baseline rate of 0 hr^?1 when the air handler was operating without a filter. Removal rates for total particulate matter less than 2.5 μm in aerodynamic diameter (PM_2.5) mass concentrations were 0.5 hr^?1 under baseline conditions, 0.5 hr^?1 during operation of three portable ionic air cleaners, 1 hr^?1 for an in-duct 1-in. media filter, 2.4 hr^?1 for a single high-efficiency particle arrestance (HEPA) portable air cleaner, 4.6 hr^?1 for an in-duct 5-in. media filter, 4.7 hr^?1 during operation of five portable HEPA filters, 6.1 hr^?1 for a conventional in-duct electronic air cleaner, and 7.5 hr^?1 for a high efficiency in-duct electrostatic air cleaner. Corresponding whole house clean air delivery rates for PM_2.5 attributable to the air cleaner independent of losses within the central ventilation system ranged from 2 m³/min for the conventional media filter to 32 m³/min for the high efficiency in-duct electrostatic device. Except for the portable ionic air cleaner, the devices considered here increased particle removal indoors over baseline deposition rates.     

Effectiveness of Photocatalytic Filter for Removing Volatile Organic Compounds in the Heating,Ventilation, and Air Conditioning System

Abstract

Nowadays, the heating, ventilation, and air conditioning (HVAC) system has been an important facility for maintaining indoor air quality. However, the primary function of typical HVAC systems is to control the temperature and humidity of the supply air. Most indoor air pollutants, such as volatile organic compounds (VOCs), cannot be removed by typical HVAC systems. Thus, some air handling units for removing VOCs should be added in typical HVAC systems. Among all of the air cleaning techniques used to remove indoor VOCs, photocatalytic oxidation is an attractive alternative technique for indoor air purification and deodorization. The objective of this research is to investigate the VOC removal efficiency of the photocatalytic filter in a HVAC system. Toluene and formaldehyde were chosen as the target pollutants. The experiments were conducted in a stainless steel chamber equipped with a simplified HVAC system. A mechanical filter coated with Degussa P25 titania photocatalyst and two commercial photocatalytic filters were used as the photo-catalytic filters in this simplified HVAC system. The total air change rates were controlled at 0.5, 0.75, 1, 1.25, and 1.5 hr^?1, and the relative humidity (RH) was controlled at 30%, 50%, and 70%. The ultraviolet lamp used was a 4-W, ultraviolet-C (central wavelength at 254 nm) strip light bulb. The first-order decay constant of toluene and form-aldehyde found in this study ranged from 0.381 to 1.01 hr^?1 under different total air change rates, from 0.34 to 0.433 hr^?1 under different RH, and from 0.381 to 0.433 hr^?1 for different photocatalytic filters.     

Treatment of hydrophobic VOCs in trickling bed air biofilter: Emphasis on long-term effect of initial alternate use of hydrophilic VOCs and microbial species evolution

The main research objective of this study is to enhance the removal of recalcitrant compounds that are not readily bioavailable due to limiting mass transfer rate between the liquid and gas phases. Four trickle-bed air biofilters (TBABs), loaded with pelletized diatomaceous earth support media, were run at an empty bed residence time (EBRT) of 120 sec. After an acclimation period at constant loading rate (LR) of n-hexane (13.2 g m^?3 hr^?1) and intermittent feeding of methanol, n-hexane influent LR was then increased in step-wise fashion to 47.7 g m^?3 hr^?1 for biofilters receiving acidic nutrients (pH 4), and to 36.3 g m^?3 hr^?1 for biofilters receiving nutrient at pH 7. The results have shown that for TBABs receiving nutrient at pH 4, greater elimination capacities were obtained as compared to TBABs working at pH 7. n-Hexane removal efficiency of more than 84% at LR up to 47.7 g m^?3 hr^?1 was obtained for pH 4 nutrient-fed biofilters, while for biofilters with nutrients fed at pH 7, the removal efficiency did not exceed 64% for n-hexane LR of 36.3 g m^?3 hr^?1. The microbial analysis revealed that no fungal community was detected in TBABs run at neutral pH. The fungi communities that were initially acclimating TBABs run at pH 4, namely, Aspergillus niger and Fusarium solani, were not detected at the end of the experiment, while Gibberella moniliformis (Fusarium verticillioides) genus became the dominant species. Gibberella moniliformis (Fusarium verticillioides) was present along all the biofilter media and sustained very high n-hexane elimination at steady-state condition.

Implications:With growing apprehension about sustainability and environmental protection, with limited resources available, and with the passage of the 1990 Amendments to the Clean Air Act, there is more need for using air pollution control techniques that are sound economically and proven environmentally friendly. Biofiltration systems, namely, trickle-bed air biofilters, were for decades recognized as efficient in treating air pollutants. Thus, the application of this technique over a wide industrial spectrum would certainly contribute to reduction of hazardous gas emissions.     

Application of neutral electrolyzed water spray for reducing dust levels in a layer breeding house

Reducing airborne dust is an essential process for improving hen housing environment. Dust reduction effects of neutral electrolyzed water (pH 8.2) spray were investigated in a commercial tunnel-ventilated layer breeding house during production in northern China. A multipoint sampler was used to measure airborne dust concentration to study the dust reduction effects and distribution in the house. Compared with the control treatment (without spray), airborne dust level was reduced 34% in the 3 hr after spraying 216 mL m^?2 neutral electrolyzed water in the breeding house. The dust concentration was significantly higher during the periods of feed distribution (1.13 ± 0.13 mg m^?3) and artificial insemination (0.72 ± 0.13 mg m^?3) compared with after spray (0.47 ± 0.09 mg m^?3) and during lights-off period (0.29 ± 0.08 mg m^?3) in the three consecutive testing days (P < 0.05). The experimental cage area was divided into four zones along the length of the house, with zone 1 nearest to the evaporative cooling pad and zone 4 nearest to the fans. The air temperature, relative humidity, airflow rate, and dust concentration were measured at the sampling points of the four zones in 3 consecutive days and mortality of the birds for the duration of a month were investigated. The results showed that the air temperature, airflow rate, dust concentration, and number of dead birds increase from zone 1 to zone 4 in the tunnel-ventilated layer breeding house.

Implications: It is difficult to effectively reduce hen house airborne dust levels and limited information is available on airborne dust distribution in tunnel-ventilated hen houses. This work investigates (i) the application of neutral electrolyzed water spray for reducing dust in a layer breeding houses; (ii) dust concentration variations in 24-hr house operation; as well as (iii) the effects of location on dust concentrations. It was demonstrated that neutral electrolyzed water spray can be efficiently used for dust reduction in poultry houses. Further, a better understanding of the dust concentration variations in 24-hr house operation and in different spatial zones can contribute to bird housing environment management and poultry house design so as to improve bird health.     

Inactivation of airborne Enterococcus faecalis and infectious bursal disease virus using a pilot-scale ultraviolet photocatalytic oxidation scrubber

High microbial concentrations and emissions associated with livestock houses raise health and environmental concerns. A pilot-scale ultraviolet photocatalytic oxidation (UV-PCO) scrubber was tested for its efficacy to inactivate aerosolized Enterococcus faecalis and infectious bursal disease virus (IBDV). Microbial reduction was determined by the difference in microbial concentrations measured in the upstream and downstream isolators that were connected to the two ends of the UV-PCO scrubber. Two UV irradiance levels were tested by using one or two UV lamps. The theoretical average UV irradiances were 6,595 µ W cm^?2 with one UV lamp and 12,799 µ W cm^?2 with two UV lamps. At the tested ventilation rate (70 m³ hr^?1), the contact time was 1 sec. Reduction rate and other two indexes (k-value and Z-value) that normalized UV radiation were calculated to describe the extent of microbial inactivation. The UV-PCO scrubber eliminated >99.7% of airborne E. faecalis from the incoming airstream under one UV lamp irradiance, and the reduction was further increased by 0.2–0.3% when the second UV lamp was added. The reduction rate for airborne IBDV was 72.4% with one UV lamp. The calculated k-values were 0.501–0.594 cm² mJ^?1 for airborne E. faecalis and 0.217 cm² mJ^?1 for IBDV. The Z-value of airborne E. faecalis to UV irradiance was 9.3 (±1.6)?×?10^?4 cm² µ W^?1 sec^?1. The results indicate that a UV-PCO scrubber can serve as an effective and efficient technology for inactivating airborne bacteria and virus. Scaling up of the pilot-scale scrubber for field use will require considerations such as design air treatment capacity, UV irradiance level, contact time, dust concentration, susceptibility of target microorganisms, and expected reduction rate.

Implications: This work demonstrated that a UV-PCO scrubber can be used to inactivate animal-associated airborne microorganisms, thus reducing microbial emissions from livestock houses and minimizing the biological impact to ambient environment. The microbial reduction efficiency by the UV-PCO scrubber varied depended on the level of UV irradiation and the target microbial species. The tested viral species (infectious bursal disease virus) was more resistant to the UV-PCO scrubber as compared to its counterpart bacterial species (E. faecalis).     

Detection Limits for Hazardous and Radioactive Elements in Airborne Aerosols Using Inductively Coupled Air Plasma – Atomic Emission Spectrometry

Abstract

This research presents investigations into the use of inductively coupled air plasma – atomic emission spectrometry (air-plasma ICPAES) to determine the presence of inorganic contaminants in airborne aerosols. Limits of detection (LOD) in the ppm to ppb range for 19 hazardous metals and radionuclides were determined for aerosols of solutions nebulized into the air plasma. For many elements, the determined LOD surpass the threshold limit values established by the American Conference of Governmental Industrial Hygienists by one to three orders of magnitude. The potential of air-plasma ICPAES for continuous on-line monitoring of airborne contaminants is discussed.     

Persistence characteristics of operationally sprayed fenitrothion in nearby unsprayed areas of a conifer forest ecosystem in New Brunswick

Abstract

Persistence characteristics of operationally sprayed fenitrothion were investigated in various substrates sampled from neighbouring unsprayed areas in New Brunswick. Air, water, sediment, aquatic plants, fish, balsam fir [Abies balsamea (L.) Mill] foliage, forest soil and litter samples were collected from random sampling locations selected within 200 m from the operational spray blocks. The same substrates were resampled from the same plots and from the same locations about a year later just prior to the commencement of the operational spraying. Control samples were collected from an unsprayed site, near Sault Ste. Marie, Ontario. All samples were analysed for fenitrothion, by gas‐liquid chromatography. Except the fish samples all the substrates collected during the time of operational spraying contained low but detectable levels of fenitrothion. When collected a year later prior to the operational spray program, only balsam fir showed any detectable levels (detection limit, 0.01 ppm) of the chemical. All other samples showed no fenitrothion residues (detection limit for air, 10 ng/m³; for water, 0.01 ppb; and for other samples, 0.01 ppm). The findings confirmed that fenitrothion does not persist for an extended period of time in the aquatic substrates. The conifer foliage, however, showed persistent residues at a level of about 0.55 ppm even after the winter months, although there was no indication of accumulation of the chemical as a result of repeated exposure. The study demonstrated that the conifer needles acted as a micro sink for the chemical which showed a tendency to persist in the leaf tissues for a considerable length of time.     

Ammonia emissions from different pig production scales and their temporal variations in the North China Plain

ABSTRACT

Pig production systems in China are shifting from small to industrial scale. Significant variation in housing ammonia (NH₃) emissions can exist due to differences in diet, housing design, and management practices. However, there is a knowledge gap regarding the impacts of farm-scale in China, which may be critical in identifying hotspots and mitigation targets. Here, continuous in-situ NH₃ concentration measurements were made at pig farms of different scales for sows and fattening pigs over periods of 3–6 days during two different seasons (summer vs. winter). For the sow farms, NH₃ emission rates were greater at the small farm (summer: 0.52 g pig^?1 hr^?1; winter: 0.21 g pig^?1 hr^?1) than at the large farm (summer: 0.34 g pig^?1 hr^?1; winter: 0.12 g pig^?1 hr^?1). For the fattening pig farms, NH₃ emission rates were greater at the large farm (summer: 0.22 g pig^?1 hr^?1; winter: 0.16 g pig^?1 hr^?1) than at the small farm (summer: 0.19 g pig^?1 hr^?1; winter: 0.07 g pig^?1 hr^?1). Regardless of farm scale, the NH₃ emission rates measured in summer were greater than those in winter; the NH₃ emission rates were greater in the daytime than at the nighttime; a positive relationship (R² = 0.06–0.68) was established between temperature and NH₃ emission rate, whereas a negative relationship (R² = 0.10–0.47) was found between relative humidity and NH₃ emission rate. The effect of farm-scale on indoor NH₃ concentration could mostly be explained by the differences in ventilation rates between farms. The diurnal variation in NH₃ concentration could be partly explained by ventilation rate (R² = 0.48–0.78) in the small traditional farms and by emission rate (R² = 0.26–0.85) in the large industrial farms, except for the large fattening pig farm in summer. Overall, mitigation of NH₃ emissions from sow farms should be a top priority in the North China Plain.

Implications: The present study firstly examined the farm-scale effect of ammonia emissions in the North China Plain. Of all farms, the sow farm was identified as the greatest source of ammonia emission. Regardless of farm scale, ammonia emission rates were observed to be higher in summer. Ammonia concentrations were mostly higher in the large industrial farms partly due to lower ventilation rates than in the small traditional farms.     

Field controlled experiments on the physiological responses of maize (Zea mays L.) leaves to low-level air and soil mercury exposures

Thousands of tons of mercury (Hg) are released from anthropogenic and natural sources to the atmosphere in a gaseous elemental form per year, yet little is known regarding the influence of airborne Hg on the physiological activities of plant leaves. In the present study, the effects of low-level air and soil Hg exposures on the gas exchange parameters of maize (Zea mays L.) leaves and their accumulation of Hg, proline, and malondialdehyde (MDA) were examined via field open-top chamber and Hg-enriched soil experiments, respectively. Low-level air Hg exposures (<50 ng m^?3) had little effects on the gas exchange parameters of maize leaves during most of the daytime (p?>?0.05). However, both the net photosynthesis rate and carboxylation efficiency of maize leaves exposed to 50 ng m^?3 air Hg were significantly lower than those exposed to 2 ng m^?3 air Hg in late morning (p?<?0.05). Additionally, the Hg, proline, and MDA concentrations in maize leaves exposed to 20 and 50 ng m^?3 air Hg were significantly higher than those exposed to 2 ng m^?3 air Hg (p?<?0.05). These results indicated that the increase in airborne Hg potentially damaged functional photosynthetic apparatus in plant leaves, inducing free proline accumulation and membrane lipid peroxidation. Due to minor translocation of soil Hg to the leaves, low-level soil Hg exposures (<1,000 ng g^?1) had no significant influences on the gas exchange parameters, or the Hg, proline, and MDA concentrations in maize leaves (p?>?0.05). Compared to soil Hg, airborne Hg easily caused physiological stress to plant leaves. The effects of increasing atmospheric Hg concentration on plant physiology should be of concern.     

Control measure implications of COVID-19 infection in healthcare facilities reconsidered from human physiological and engineering aspects

The Wells-Riley model invokes human physiological and engineering parameters to successfully treat airborne transmission of infectious diseases. Applications of this model would have high potentiality on evaluating policy actions and interventions intended to improve public safety efforts on preventing the spread of COVID-19 in an enclosed space. Here, we constructed the interaction relationships among basic reproduction number (R₀) − exposure time − indoor population number by using the Wells-Riley model to provide a robust means to assist in planning containment efforts. We quantified SARS-CoV-2 changes in a case study of two Wuhan (Fangcang and Renmin) hospitals. We conducted similar approach to develop control measures in various hospital functional units by taking all accountable factors. We showed that inhalation rates of individuals proved crucial for influencing the transmissibility of SARS-CoV-2, followed by air supply rate and exposure time. We suggest a minimum air change per hour (ACH) of 7 h⁻¹ would be at least appropriate with current room volume requirements in healthcare buildings when indoor population number is < 10 and exposure time is < 1 h with one infector and low activity levels being considered. However, higher ACH (> 16 h⁻¹) with optimal arranged-exposure time/people and high-efficiency air filters would be suggested if more infectors or higher activity levels are presented. Our models lay out a practical metric for evaluating the efficacy of control measures on COVID-19 infection in built environments. Our case studies further indicate that the Wells-Riley model provides a predictive and mechanistic basis for empirical COVID-19 impact reduction planning and gives a framework to treat highly transmissible but mechanically heterogeneous airborne SARS-CoV-2.

     

Airborne molds and mycotoxins associated with handling of corn silage and oilseed cakes in agricultural environment

In agricultural areas, the contamination of feedstuffs with molds and mycotoxins presents major environmental and health concerns. During cattle feeding, fungi and mycotoxins were monitored in corn silage, oilseed cakes and bioaerosols collected in Normandy. Most of the corn silages were found to be contaminated by deoxynivalenol (mean concentration: 1883 μg kg^?1) while a few of oilseed cakes were contaminated by alternariol, fumonisin B₁ or gliotoxin. In ambient bioaerosols, the values for fungi per cubic meter of air varied from 4.3 × 10² to 6.2 × 10⁵ cfu m^?3. Seasonal variations were observed with some species like Aspergillus fumigatus which significantly decreased between the 2 seasons (P = 0.0186) while the Penicillium roqueforti group significantly increased during the second season (P = 0.0156). In the personal bioaerosols, the values for fungi per cubic meter of air varied from 3.3 10³ to 1.7 10⁶ cfu m^?3 and the number of A. fumigatus spores significantly decreased between the 2 seasons (P = 0.0488). Gliotoxin, an immunosuppressive mycotoxin, was quantified in 3 personal filters at 3.73 μg m^?3, 1.09 μg m^?3 and 2.97 μg m^?3.     

Gas-phase photolytic production of hydroxyl radicals in an ultraviolet purifier for air and surfaces

We have measured the concentration of hydroxyl radicals (OH) produced in the gas phase by a commercially available purifier for air and surfaces, using the time rate of decay of n-heptane added to an environmental chamber. The hydroxyl generator, an Odorox® BOSS? model, produces the OH through 185-nm photolysis of ambient water vapor. The steady-state concentration of OH produced in the 120 m³ chamber is, with 2σ error bars, (3.25 ± 0.80) × 10⁶ cm^?3. The properties of the hydroxyl generator, in particular the output of the ultraviolet lamps and the air throughput, together with an estimation of the water concentration, were used to predict the amount of OH produced by the device, with no fitted parameters. To relate this calculation to a steady-state concentration, we must estimate the OH loss rate within the chamber owing to reaction with the n-heptane and the 7 ppb of background hydrocarbons that are present. The result is a predicted steady-state concentration in excellent agreement with the measured value. This shows we understand well the processes occurring in the gas phase during operation of this hydroxyl radical purifier.

Implications: Hydroxyl radical air purifiers are used for cleaning both gaseous contaminants, such as volatile organic compounds (VOCs) or hazardous gases, and biological pathogens, both airborne and on surfaces. This is the first chemical kinetic study of such a purifier that creates gas-phase OH by ultraviolet light photolysis of H₂O. It shows that the amount of hydroxyls produced agrees well with nonparameterized calculations using the purifier lamp output and device airflow. These results can be used for designing appropriate remediation strategies.     

Biotrickling filtration of airborne styrene: A comparison of filtration media

This study compares the performances of fern and plastic chips as packing media for the biofiltration of a styrene-laden waste gas stream emitted in a plant for the manufacture of plastic door plates. Fern chips (with a specific surface area of 1090 m² m^?3) and plastic chips (with a specific surface area of 610 m² m^?3) were packed into a pilot-scale biotrickling filter with a total medium volume of 50 L for the performance test. Field waste gas with styrene concentrations in the range of 161–2390 mg Am^?3 at 28–30 °C) was introduced to the bed and a fixed empty-bed retention time (EBRT) of 21 sec, a volumetric gas flow rate of 8.57 m³ hr^?1, and superficial gas velocity of 53.6 m hr^?1 were maintained throughout the experimental period. Nutrients containing metal salts, nitrogen, phosphorus, and milk were supplemented to the filters for maintaining the microbial activities. Results reveal that the biotrickling filter developed in this study had the highest styrene monomer (SM) elimination capacities (170 g m^?3 hr^?1 for fern-chip packing and 300 g m^?3 hr^?1 for plastic-chip packing) among those cited in the literature. The plastic medium is a favorable substitute for endangered fern chips. The thermal-setting nature of plastic chips limits their recycle and reuse as raw materials, and the study provides an opportunity for the utilization of the materials.

Implications: Biotreatment of contaminants in air streams offers an inexpensive and efficient alternative to conventional technologies. Biofiltration has a great potential for the degradation of gas-borne styrene and total hydrocarbon (THC) removal efficiency of around 80%. The objective of this research was to compare the performances of fern chips and a kind of plastic chips as packing media for biofiltration of the styrene-laden waste gas stream emitted from cutting operations of stripes of premixed unsaturated polyester (UP) and styrene paste before hot-pressing operations for making plastic door plates. From a practical point of view, the plastic medium can be a good substitute medium for fern chips, which has been declared as a protected plant. This study provides an experimentally verified model for the design and operation of such biotreatment systems.     

The APCA Exhibition

On June 5 and 6 of 1980, two parallel plume oxidation studies were carried out in the vicinity of the Tennessee Valley Authority's Colbert Steam Plant. One study was performed in a smog chamber into which stack gases were injected and mixed with ambient air. The other study included direct airborne sampling of the power plant plume. Atmospheric oxidation rates for the conversion of SO₂ to SO₄ ^2- and the removal rates of NO _x (which is presumably the rate of NO₃ ^- formation) were estimated for both studies. The SO₂ to SO₄ ^2- rate coefficients were found to be 0.022 ± 0.009 h^-1 for both chamber experiments and the first airborne sampling day. For the second day, a rate constant of 0.041 ± 0.052 h^-1 was estimated from the aircraft data. The large deviation in this value is explained by the fact that the plume from the power plant combined and reacted with the urban plume from the city of Florence, AL. The formation of a very large "O3 bulge" on this day is also attributed to the mixed plumes. The first order rate coefficients for NO _x removal were estimated to be 0.27 ± 0.14 h^-1 for both chamber experiments and the first airborne sampling day. A NO _x removal rate could not be determined for the second airborne sampling day.