Biofiltration Control of Hydrogen Sulfide 1. Design and Operational Parameters

Laboratory scale biological filter systems for control of hydrogen sulfide (H₂S) in waste gas have been studied and the optimum design and operating parameters determined. Extensive tests have been conducted to evaluate the effect of various filter bed operating parameters such as temperature, retention time, H₂S concentration, and H₂S loading rate. Variable properties of new and used composts such as sulfate content, acidity, and water content have been studied for their influence on H₂S removal efficiency. The effects of compost particle size distribution on system pressure drop and the maximum H₂S elimination capacity were examined. Biofiltration systems containing various types of yard waste compost as the filter material have been observed to remove hydrogen sulfide with efficiencies greater than 99.9 percent for H₂S inlet concentrations in the range from 5 to 2650 ppmv.     

Hydrogen Sulfide Generation in Simulated Construction and Demolition Debris Landfills: Impact of Waste Composition

Abstract

Hydrogen sulfide (H₂S) generation in construction and demolition (C&D) debris landfills has been associated with the biodegradation of gypsum drywall. Laboratory research was conducted to observe H₂S generation when drywall was codisposed with different C&D debris constituents. Two experiments were conducted using simulated landfill columns. Experiment 1 consisted of various combinations of drywall, wood, and concrete to determine the impact of different waste constituents and combinations on H₂S generation. Experiment 2 was designed to examine the effect of concrete on H₂S generation and migration. The results indicate that decaying drywall, even alone, leached enough sulfate ions and organic matter for sulfate-reducing bacteria (SRB) to generate large H₂S concentrations as high as 63,000 ppmv. The codis-posed wastes show some effect on H₂S generation. At the end of experiment 1, the wood/drywall and drywall alone columns possessed H₂S concentrations >40,000 ppmv. Conversely, H₂S concentrations were <1 ppmv in those columns containing concrete. Concrete plays a role in decreasing H₂S by increasing pH out of the range for SRB growth and by reacting with H₂S. This study also showed that wood lowered H₂S concentrations initially by decreasing leachate pH values. Based on the results, two possible control mechanisms to mitigate H₂S generation in C&D debris landfills are suggested.     

Kinetics and the mass transfer mechanism of hydrogen sulfide removal by biochar derived from rice hull

The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperature has great influence on the adsorption of H₂S. At the different pyrolysis temperature, the H₂S removal efficiency of rice hull-derived biochar was different. The adsorption capacities of biochar were 2.09 mg·g^–1, 2.65 mg·g^–1, 16.30 mg·g^–1, 20.80 mg·g^–1, and 382.70 mg·g^–1, which their pyrolysis temperatures were 100 °C, 200 °C, 300 °C, 400 °C and 500 °C respectively. Based on the Yoon-Nelson model, it analyzed the mass transfer mechanism of hydrogen sulfide adsorption by biochar.

Implications: The paper focuses on the biochar derived from rice hull–removed hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperatures have great influence on the adsorption of H₂S. At the different pyrolysis temperatures, the H₂S removal efficiency of rice hull–derived biohar was different. The adsorption capacities of biochar were 2.09, 2.65, 16.30, 20.80, and 382.70 mg·g^?1, and their pyrolysis temperatures were 100, 200, 300, 400, and 500 °C, respectively. Based on the Yoon-Nelson model, the mass transfer mechanism of hydrogen sulfide adsorption by biochar was analyzed.     

A Simple Neural Network for Estimating Emission Rates of Hydrogen Sulfide and Ammonia from Single Point Sources

Abstract

Neural networks have shown tremendous promise in modeling complex problems. This work describes the development and validation of a neural network for the purpose of estimating point source emission rates of hazardous gases. This neural network approach has been developed and tested using experimental data obtained for two specific air pollutants of concern in West Texas, hydrogen sulfide and ammonia. The prediction of the network is within 20% of the measured emission rates for these two gases at distances of less than 50 m. The emission rate estimations for ground level releases were derived as a function of seven variables: downwind distance, crosswind distance, wind speed, downwind concentration, atmospheric stability, ambient temperature, and relative humidity. A backpropagation algorithm was used to develop the neural network and is also discussed here. The experimental data were collected at the Wind Engineering Research Field Site located at Texas Tech University in Lubbock, Texas. Based on the results of this study, the use of neural networks provides an attractive and highly effective tool to model atmospheric dispersion, in which a large number of variables interact in a nonlinear manner.     

Effectiveness and mechanisms of hydrogen sulfide adsorption by camphor-derived biochar

The characteristics and mechanisms of hydrogen sulfide (H₂S) adsorption on a biochar through pyrolysis at various temperatures (100 to 500°C) were investigated. The biochar used in the current study was derived from the camphor tree (Cinnamomum camphora). The samples were ground and sieved to produce particle sizes of 0.4 mm to 1.25 mm, 0.3 mm to 0.4 mm, and <0.3 mm. The H₂S breakthrough capacity was measured using a laboratory-designed test. The surface properties of the biochar were characterized using pH and Fourier-transform infrared spectroscopy (FTIR) analysis. The results obtained demonstrate that all camphor-derived biochars were effective in H₂S sorption. Certain threshold ranges of the pyrolysis temperature and surface pH were observed, which, when exceeded, have dramatic effects on the H₂S adsorption capacity. The sorption capacity ranged from 1.2 mg/g to 121.4 mg/g. The biochar with 0.3 mm to 0.4 mm particle size possesses a maximum sorption capacity at 400°C. The pH and FTIR analysis results showed that carboxylic and hydroxide radical groups were responsible for H₂S sorption. These observations will be helpful in designing biochar as engineered sorbents for the removal of H₂S.

Implications: This paper studies the potential of biochar derived by camphor to adsorb hydrogen sulfide at environmentally sustainable temperatures. The different sizes of the biochars and the different temperatures of pyrolysis for the camphor particle have a great impact on adsorption of hydrogen sulfide.     

Adsorption of hydrogen sulfide by biochars derived from pyrolysis of different agricultural/forestry wastes

The characteristics and mechanisms of hydrogen sulfide (H₂S) adsorption on three different biochars derived from agricultural/forestry wastes through pyrolysis at various temperatures (100 to 500 ºC) were investigated. In this study, the H₂S breakthrough capacity was measured using a laboratory-characterized using pH and Fourier transform infrared spectroscopy analysis. The results obtained demonstrate that all biochars were effective in H₂S sorption. The sorption capacity of the biochar for H₂S removal is related to the pyrolysis temperature and pH of the surface. Certain threshold ranges of the pyrolysis temperature (from 100 to 500 ºC) and pH of the surface are presented. It also concluded that the sorption capacity (for removing H₂S) of rice hull-derived biochar is the largest in three biochars (camphor-derived biochar, rice hull-derived biochar, and bamboo-derived biochar). These observations will be helpful in designing biochar as engineered sorbents for the removal of H₂S.Implications: This paper focuses on the adsorption of hydrogen sulfide (H₂S) by biochars derived from wastes. The characteristics and mechanisms of hydrogen sulfide (H₂S) adsorption on three different boichars derived from agricultural/forestry wastes through pyrolysis at various temperatures were investigated. In this study, the H₂S breakthrough capacity was measured using laboratory characterization with pH and Fourier-transform infrared spectroscopy analysis. The results obtained demonstrate that all biochars were effective in H₂S sorption. The sorption capacity of the biochar for H₂S removal is related to the pyrolysis temperature and pH of the surface.     

酸碱改性对氧化铁脱硫剂脱硫性能影响的研究

通过酸碱改性制备了酸式和碱式2种不同表面性质的常温氧化铁脱硫剂,并采用FT-IR技术对其表面酸碱性质和净化硫化氢废气活性进行了研究.结果表明,表面酸碱件质不同的脱硫剂其脱硫反应行为也不同,在脱硫过程中硫化氢氧化生成的硫酸及亚硫酸会影响脱硫剂的表面酸碱性质,造成酸式脱硫剂的表面酸性更强,从而抑制了硫化氢分子在酸式脱硫剂表...     

培养方式对废水脱氮与沼气脱硫污泥驯化影响

实验研究了底物、接种污泥和微生物生长方式对猪场废水脱氮和沼气脱硫耦联污泥驯化及活性恢复的影响,以解决快速富集培养废水脱氮与沼气脱硫微生物的问题。研究发现,就脱氮脱硫均达到60%的时间而言,接种厌氧污泥反应器为9 d,比接种好氧污泥反应器(18 d)和不接种污泥加填料反应器(21 d)更短。以含氮含硫废水为底物驯化时,接种厌氧污泥更有利于脱氮脱硫污泥的驯化;而同为接种好氧污泥时,以含氮含硫废水为底物的驯化方式更有利于脱氮脱硫污泥的驯化。污泥活性恢复实验中,以含氮废水+沼气(H2S)为底物培养驯化的污泥,硫转化活性恢复所用的时间为15 d,比含氮含硫废水为底物驯化污泥的活性恢复时间更长。     

Carbon Monoxide in an Urban Environment: Application of a Receptor Model for Source Apportionment

During the winter of 1985-86 the authors took 6-h integrated air samples and measured the concentrations of carbon monoxide and other gases at a residential site in Olympia, Washington. The 6-h average concentrations were between about 0.2 and 3.2 ppmv. For each 6-h period the observed concentration of CO was apportioned among its sources which were residential wood burning and automobiles. Small and generally insignificant amounts of CO were also observed from unidentified sources. A chemical mass balance (CMB) was formulated and applied to apportion the observed CO among its sources. Methylchloride (CH₃CI), in excess of background levels, was used as a unique tracer of wood burning and excess hydrogen (H₂) served as a tracer of CO from automobiles. The source emission factors to carry out the calculations were estimated from other experiments. The results showed that in Olympia, wood burning can often contribute as much CO as automobiles during winter. The maximum 6-h average contribution of CO from wood burning was about 2 ppmv and from automobiles it was 2.2 ppmv, and the average ambient concentration was about 1 ppmv. When pollution from wood burning was present, it contributed 0.5 ppmv on average while automobiles also contributed 0.5 ppmv. Unidentified sources contributed 0.1 ppmv and the background level was 0.15 ppmv. During the winter many times wood burning did not affect CO concentrations, while CO from automobiles was always present. On average, during the winter, automobiles contributed some 50 percent of the CO mass to the lower urban atmosphere and wood burning contributed about 30 percent. Diurnal cycles became evident in the calculated concentrations of CO from wood burning and automobiles even though the measured concentrations did not show strong diurnal variations. Wood burning contributed most during evening and nighttime and very little during the day, while automobiles contributed most during the morning and evening hours and very little at night. These patterns lend support to the accuracy of the model and source emission factors since they are as expected from the diurnal variations of the sources and atmospheric mixing.     

Comment on Long Term Ozone Trends

Under Title III of SARA, companies must provide information about chemicals that they manufacture, store, or process. Communities will use data about potential accidental releases to develop local emergency plans. Data about routine chemical releases will be made available to the public on a computer data base. Simply having such data available does not ensure consensus about reducing potential chemical risks. Laboratory and field research are summarized, indicating that people tend to edit small risks to zero as being too small to worry about, or to adjust them imperfectly from an anchor equal to the potential loss. These results suggest recommendations for communicating about the risks posed by accidental or routine releases of chemicals.     

A Microcomputer-based Forecasting Model: Potential Applications for Emergency Response Plans and Air Quality Studies

Most atmospheric transport and diffusion models within emergency response systems have very limited physics and are forced to rely on the assumption that wind and turbulence conditions at the time of the release will be representative over the period for which dispersion must be predicted. For releases where the principal concern is about the first few kilometers of travel, such an assumption is appropriate. However, for large accidental releases during stable conditions, the plume may travel for several hours before it is diluted to safe levels and the assumption of persistence may be inappropriate, particularly for transport in complex terrain. Under these circumstances, a model that can forecast changes in wind and turbulence conditions is required. We have installed such a model on microcomputers and tested it in complex terrain near Salt Lake City. One-hour tracer releases produced surface concentrations that remain high for much longer times than that expected based on one hour’ travel time with the mean wind at the source height. Furthermore, relatively large concentrations were found at distances of over 40 km from the source. The model was generally able to reproduce the principal features described by the measurements, although some effects of subgrid scale terrain were missed.     

Deodorization of Dimethyl Sulfide Using a Discharge Approach at Room Temperature

Abstract

The traditional technologies for odor removal of thiol usually create either secondary pollution for scrubbing, adsorption, and absorption processes, or sulfur (S) poisoning for catalytic incineration. This study applied a laboratory-scale radio-frequency plasma reactor to destructive percentage-grade concentrations of odorous dimethyl sulfide (CH₃SCH₃, or DMS). Odor was diminished effectively via reforming DMS into mainly carbon disulfide (CS₂) or sulfur dioxide (SO₂). The removal efficiencies of DMS elevated significantly with a lower feeding concentration of DMS or a higher applied rf power. A greater inlet oxygen (O₂)/DMS molar ratio slightly improved the removal efficiency. In an O₂-free environment, DMS was converted primarily to CS₂, methane (CH₄), acetylene (C₂H₂), ethylene (C₂H₄), and hydrogen (H₂), with traces of hydrogen sulfide (H₂S), methyl mercaptan (CH₃SH), and dimethyl disulfide. In an O₂-containing environment, the species detected were SO₂, CS₂, carbonyl sulfide, carbon dioxide (CO₂), CH₄, C₂H₄, C₂H₂, H₂, formal-dehyde, and methanol. Differences in yield of products were functions of the amounts of added O₂ and the applied power. This study provided useful information for gaining insight into the reaction pathways for the DMS dissociation and the formation of products in the plasmolysis and conversion processes.     

活性炭纤维生物挂膜脱除硫化氢

生物脱硫法作为一种高效、高实用性的除硫新技术而受到越来越多的关注。以活性炭纤维为微生物载体,通过活性污泥上清液挂膜驯化,考察硫化氢进气量、喷淋量、pH值和硫酸根离子浓度等条件对脱硫效率的影响。研究结果表明,在室温下,硫化氢负荷为90 g/(m3.h),进气浓度控制在3 g/m3,进气量为60 L/h,喷淋量为250～650 L/(m3.d),pH为2～5的条件下,生物活性炭纤维对硫化氢的去除率可保持在98%以上。     

Modifications to an H2S Tape Sampler for Increasing Sensitivity and Accuracy in H2S Sampling

The tape samplers using lead acetate impregnated paper tapes for continuous hydrogen sulfide sampling are subject to a number of errors which can throw considerable doubt on the accuracy of H₂S concentrations being measured. Some of the errors have been minimized with a change in the humidification system and a reduction of the lamp intensity in the optical system.     

Characteristics of puff dispersion in an urban environment

Instantaneous releases of sulfur hexafluoride tracer were carried out as part of the Joint Urban 2003 field campaign in Oklahoma City. Data from 10 fast-response tracer samplers were used to examine the crosswind and along-wind spread of the tracer, the decay of tracer concentrations, and the retention of tracer within approximately 1 km of the release locations. The time variation of the median values of the tracer concentrations, normalized by the peak value observed at a given sampler, could be approximately described by an exponential decay with characteristic decay times on the order of 1–2 min. The longer times were found for early morning releases and the shorter times were associated with later morning or afternoon releases, suggesting that atmospheric stability or the depth of the mixed layer may affect puff dispersion even in urban environments. The median retention times required for 99% of the exposure to be realized at a given location were found to be correlated reasonably well with the median decay times. These characteristic time scales should be regarded as lower limits for concentration decay because the analysis excluded a number of anomalous cases in which the decaying concentrations exhibited an extended tail that indicated a very slow ventilation rate. The median values of the along-wind dispersion parameter σ_x grouped into downwind distance ranges can be described by a linear variation with distance with an initial “hold up” contribution due to building effects of about 30–45 m, but there are considerable variations about this relationship. Downwind 0.5–1 km from the release point the lateral puff dispersion (σ_y) was roughly 70% of the along-wind dispersion.     

Sulfur Toxicity and Media Capacity for H2S Removal in Biofilters Packed with a Natural or a Commercial Granular Medium

Abstract

Two types of media, a natural medium (wood chips) and a commercially engineered medium, were evaluated for sulfur inhibition and capacity for removal of hydrogen sulfide (H₂S). Sulfate was added artificially (40, 65, and 100 mg of S/g of medium) to test its effect on removal efficiency and the media. A humidified gas stream of 50 ppm by volume H₂S was passed through the media-packed columns, and effluent readings for H₂S at the outlet were measured continuously. The overall H₂S baseline removal efficiencies of the column packed with natural medium remained >95% over a 2-day period even with the accumulated sulfur species. Added sulfate at a concentration high enough to saturate the biofilter moisture phase did not appear to affect the H₂S removal process efficiency. The results of additional experiments with a commercial granular medium also demonstrated that the accumulation of amounts of sulfate sufficient enough to saturate the moisture phase of the medium did not have a significant effect on H₂S removal.

When the pH of the biofilter medium was lowered to 4, H₂S removal efficiency did drop to 36%. This work suggests that sulfate mass transfer through the moisture phase to the biofilm phase does not appear to inhibit H₂S removal rates in biofilters. Thus, performance degradation for odor-removing biofilters or H₂S breakthrough in field applications is probably caused by other consequences of high H₂S loading, such as sulfur precipitation.     

多层生物滤塔净化硫化氢废气研究

以木屑为填料,采用多层生物滤塔净化H2S气体,研究其适宜的工艺条件及生物降解宏观动力学.结果表明,填料分层可提高H2S去除率,当进气容积负荷＜153.2 g H2S/(m3·d)时,H2S的去除率保持在90%以上;进气浓度低于70 mg/m3,下层200mm填料对H2S总去除率的贡献在50%以上;填料含水率为50%～6...     

Hydrogen sulfide ameliorates lead-induced morphological, photosynthetic, oxidative damages and biochemical changes in cotton

Poisonous lead (Pb), among heavy metals, is a potential pollutant that readily accumulates in soils and thus adversely affects physiological processes in plants. We have evaluated how exogenous H₂S affects cotton plant physiological attributes and Pb uptake under Pb stress thereby understanding the role of H₂S in physiological processes in plants. Two concentrations (0 and 200 μM) of H₂S donor sodium hydrosulfide (NaHS) were experimented on cotton plants under Pb stress (0, 50, and 100 μM). Results have shown that Pb stress decreased plant growth, chlorophyll contents, SPAD value, photosynthesis, antioxidant activity. On the other hand, Pb stress increased the level of malondialdehyde (MDA), electrolyte leakage (EL), and production of H₂O₂ and uptake of Pb contents in all three parts of plant, viz. root, stem, and leaf. Application of H₂S slightly increased plant growth, chlorophyll contents, SPAD value, photosynthesis, and antioxidant activity as compared to control. Hydrogen sulfide supply alleviated the toxic effects of lead on plant growth, chlorophyll contents, SPAD value, photosynthesis, and antioxidant activity in cotton plants. Hydrogen sulfide also reduced MDA, EL, and production of H₂O₂ and endogenous Pb levels in the three mentioned plant parts. On the basis of our results, we conclude that H₂S has promotive effects which could improve plant survival under Pb stress.     

Operational Characteristics of Effective Removal of H2S and NH3 Waste Gases by Activated Carbon Biofilter

Abstract

Simultaneous removal of hydrogen sulfide (H₂S) and am- gases. monia (NH₃) gases from gaseous streams was studied in a biofilter packed with granule activated carbon. Extensive studies, including the effects of carbon (C) source on the growth of inoculated microorganisms and gas removal efficiency, product analysis, bioaerosol emission, pressure drop, and cost evaluation, were conducted. The results indicated that molasses was a potential C source for inoculated cell growth that resulted in removal efficiencies of 99.5% for H₂S and 99.2% for NH₃. Microbial community observation by scanning electron microscopy indicated that granule activated carbon was an excellent support for microorganism attachment for long-term waste gas treatment. No disintegration or breakdown of biofilm was found when the system was operated for 140 days. The low bioaerosol concentration emitted from the biofilter showed that the system effectively avoided the environmental risk of bioaerosol emission. Also, the system is suitable to apply in the field because of its low pressure drop and treatment cost. Because NH₃ gas was mainly converted to organic nitrogen, and H₂S gas was converted to elemental sulfur, no acidification or alkalinity phenomena were found because of the metabolite products. Thus, the results of this study demonstrate that the biofilter is a feasible bioreactor in the removal of waste gases.     

Hydrogen Sulfide Gas Treatment by a Chemical‐Biological Process: Chemical Absorption and Biological Oxidation Steps

In order to remove high concentrations of hydrogen sulfide (H₂S) gas from anaerobic wastewater treatments in livestock farming, a novel process was evaluated for H₂S gas abatement involving the combination of chemical absorption and biological oxidation processes. In this study, the extensive experiments evaluating the removal efficiency, capacity, and removal characteristics of H₂S gas by the chemical absorption reactor were conducted in a continuous operation. In addition, the effects of initial Fe^2 + concentrations, pH, and glucose concentrations on Fe^2 + oxidation by Thiobacillus ferrooxidans CP9 were also examined. The results showed that the chemical process exhibited high removal efficiencies with H₂S concentrations up to 300 ppm, and nearly no acclimation time was required. The limitation of mass‐transfer was verified as the rate‐determining step in the chemical reaction through model validation. The Fe^2 + production rate was clearly affected by the inlet gas concentration as well as flow rate and a prediction equation of ferrous production was established. The optimal operating conditions for the biological oxidation process were below pH 2.3 and 35°C in which more than 90% Fe^3 + formation ratio was achieved. Interestingly, the optimal glucose concentration in the medium was 0.1%, which favored Fe^2 + oxidation and the growth of T. ferrooxidans CP9.