The Fate and Behavior of Mercury in Coal-Fired Power Plants

Abstract

For the past 22 years in the Netherlands, the behavior of Hg in coal-fired power plants has been studied extensively. Coal from all over the world is fired in Dutch power stations. First, the Hg concentrations in these coals were measured. Second, the fate of the Hg during combustion was established by performing mass balance studies. On average, 43 ± 30% of the Hg was present in the flue gases downstream of the electrostatic precipitator (ESP; dust collector). In individual cases, this figure can vary between 1 and 100%. Important parameters are the Cl content of the fuel and the flue gas temperature in the ESP. On average, 54 ± 24% of the gaseous Hg was removed in the wet flue-gas desulfurization (FGD) systems, which are present at all Dutch coal-power stations. In individual cases, this removal can vary between 8% (outlier) and 72%.

On average, the fate of Hg entering the power station in the coal was as follows: <1% in the bottom ash, 49% in the pulverized fuel ash (ash collected in the ESP), 16.6% in the FGD gypsum, 9% in the sludge of the wastewater treatment plant, 0.04% in the effluent of the wastewater treatment plant, 0.07% in fly dust (leaving the stack), and 25% as gaseous Hg in the flue gases and emitted into the air. The distribution of Hg over the streams leaving the FGD depends strongly on the installation. On average, 75% of the Hg was removed, and the final concentration of Hg in the emitted flue gases of the Dutch power stations was only ~3 μg/m_STP ³ at 6% O₂. During co-combustion with biomass, the removal of Hg was similar to that during 100% coal firing.

Speciation of Hg is a very important factor. An oxidized form (HgCl₂) favors a high degree of removal. The conversion from Hg⁰ to HgCl₂ is positively correlated with the Cl content of the fuel. A catalytic DENOX (SCR) favors the formation of oxidized Hg, and, in combination with a wet FGD, the total removal can be as high as 90%.     

Asbestos: Rationale Behind A Proposed Air Quality Standard

A computerized simulation model has been developed to compute energy requirements of a limestone slurry flue gas desulfurization (FGD) system as a function of FGD system design parameters, power plant characteristics, coal properties, and sulfur dioxide emission regulation. Results are illustrated for a "base case" plant of 500 MW, burning 3.5% sulfur coal, meeting the federal new source performance standard of 1.2 lb SO₂/10⁶ Btu. The flue gas is cleaned by an electrostatic precipitator followed by a limestone FGD system with a TCA scrubbing vessel and an optimized in-line steam reheater. The total FGD system energy requirement for this case was found to be 3.4% of the total energy input to the boiler. Sensitivity analyses were then performed in which the nominal values of ten system parameters were individually varied. This caused the total FGD system energy requirement to vary between 2.5 % and 6.1 % of the gross plant output for the range of parameters tested. The most sensitive parameters were found to be scrubbing slurry pH, which affects pumping requirements, and stack gas exit temperature, which affects reheat requirements. In all cases, FGD energy requirements were minimized when the SO₂ emission standard was met by partially bypassing the scrubber. In light of the recent Clean Air Act Amendments this option may not be feasible in the future.     

Resource Recovery from Flue Gas Desulfurization Systems

The cost effective benefits of yielding a flue gas desulfurization (FGD) sludge predominantly composed of CaSO₄·2H₂O, have been previously established. The recovery of this material as FGD by-product gypsum has been demonstrated abroad. Recently U.S. wallboard manufacturers have recognized the viability of this recovery practice. Such techno-economic decision making variables as a) by-product specification, b) transportation costs, and c) location of suitable FGD systems enable the recognition of FGD by-product recovery. Recent investigations of resultant solids content and chloride washing reflect the technical possibility of delivering a suitable product. Commercial and economic factors favor recovery based upon rising disposal and transportation costs. Existing and near term proposed systems surface the technical and commercial problems faced by utilities considering recovery.

Generation of an oxidized FGD sludge consisting of 90⁺% CaSO₄·2H₂O and dewatered to 80⁺% solids is technically achievable by air sparging within the FGD system. Although the product is suitable for land disposal, electric power utilities should consider and evaluate by-product recovery. U.S. wallboard manufacturers have established technical criteria for FGD by-product gypsum. Percent CaSO₄·2H₂O, final solids content, particle size, and chloride content are primarily technical parameters. Technology exists within the FGD industry to satisfy these criteria and results are discussed.

Economic factors comparing mining costs, transportation costs, and disposal costs are developed for specific utility projects. Such comparison established generalized financial criteria for a given utility to develop the economic reasonableness of considering FGD byproduct recovery.

End product user perspectives are presented providing electric utilities with a realistic appreciation for by-product recovery potential. Location of existing wallboard plants highlight potential recovery regions. Quality control problems are discussed in terms of generating a by-product rather than a disposable material.     

Technical Description of Parameters Influencing the pH Value of Suspension Absorbent Used in Flue Gas Desulfurization Systems

Abstract

As a result of the large limestone deposits available in Poland, the low cost of reagent acquisition for the large-scale technological use and relatively well-documented processes of flue gas desulfurization (FGD) technologies based on limestone sorbent slurry, wet scrubbing desulfurization is a method of choice in Poland for flue gas treatment in energy production facilities, including power plants and industrial systems. The efficiency of FGD using the above method depends on several technological and kinetic parameters, particularly on the pH value of the sorbent (i.e., ground limestone suspended in water). Consequently, many studies in Poland and abroad address the impact of various parameters on the pH value of the sorbent suspension, such as the average diameter of sorbent particles (related to the limestone pulverization degree), sorbent quality (in terms of pure calcium carbonate [CaCO₃] content of the sorbent material), stoichiometric surfeit of CaCO₃ in relation to sulfur dioxide (SO₂) absorbed from flue gas circulating in the absorption node, time of absorption slurry retention in the absorber tank, chlorine ion concentration in sorbent slurry, and concentration of dissolved metal salts (Na, K, Mg, Fe, Al, and others). This study discusses the results of laboratory-scale tests conducted to establish the effect of the above parameters on the pH value of limestone slurry circulating in the SO₂ absorption node. On the basis of the test results, a correlation equation was postulated to help maintain the desirable pH value at the design phase of the wet FGD process. The postulated equation displays good coincidence between calculated pH values and those obtained using laboratory measurements.     

Laboratory Wind Tunnel and Model Studies to Improve Gas Velocity Distribution in Cottrell Precipitators

Corrosion of flue gas desulfurization (FGD) scrubbing equipment is one of several critical problems facing both the power industry operating these units and the engineering firms that have to select materials of construction for the specific processes. The various processes and the status of flue-gas desulfurization technology were discussed at the 68th annual meeting of the Air Pollution Control Association.¹     

Simultaneous removal of NOx,SO2, and Hg from flue gas in FGD absorber with oxidant injection (NaClO2)– full-scale investigation

ABSTRACT

This article presents the results of an industrial-scale study (on 400 MW_e lignite fired unit) of simultaneous NO_x, SO₂, and Hg^T removal in FGD absorber with oxidant injection (NaClO₂) into flue gas. It was confirmed that the injection of sodium chlorite upstream the FGD (Flue Gas Desulfurization) absorber oxidize NO to NO₂, Hg⁰ to Hg²⁺, and enhancing NO_x and Hg^T removal efficiency from exhaust gas in FGD absorber. Mercury removal efficiency grows with the rise of degree of oxidation NO to NO₂ and was limited by the phenomenon of re-emission. For NO_x removal the most critical parameters is slurry pH and temperature. There was no negative effect on sulfur dioxide removal efficiency caused by oxidant injection in tested FGD absorber. Based on the data provided, NO_x and Hg^T emissions can be reduced by adjusting the FGD absorber operating parameters combined with oxidant injection.     

Flue Gas Desulfurization: The State of the Art

ABSTRACT

Coal-fired electricity-generating plants may use SO₂ scrubbers to meet the requirements of Phase II of the Acid Rain SO₂ Reduction Program. Additionally, the use of scrubbers can result in reduction of Hg and other emissions from combustion sources. It is timely, therefore, to examine the current status of SO₂ scrubbing technologies. This paper presents a comprehensive review of the state of the art in flue gas desulfurization (FGD) technologies for coal-fired boilers.

Data on worldwide FGD applications reveal that wet FGD technologies, and specifically wet limestone FGD, have been predominantly selected over other FGD technologies. However, lime spray drying (LSD) is being used at the majority of the plants employing dry FGD technologies. Additional review of the U.S. FGD technology applications that began operation in 1991 through 1995 reveals that FGD processes of choice recently in the United States have been wet limestone FGD, magnesium-enhanced lime (MEL), and LSD. Further, of the wet limestone processes, limestone forced oxidation (LSFO) has been used most often in recent applications.

The SO₂ removal performance of scrubbers has been reviewed. Data reflect that most wet limestone and LSD installations appear to be capable of ~90% SO₂ removal. Advanced, state-of-the-art wet scrubbers can provide SO₂ removal in excess of 95%.

Costs associated with state-of-the-art applications of LSFO, MEL, and LSD technologies have been analyzed with appropriate cost models. Analyses indicate that the capital cost of an LSD system is lower than those of same capacity LSFO and MEL systems, reflective of the relatively less complex hardware used in LSD. Analyses also reflect that, based on total annualized cost and SO₂ removal requirements: (1) plants up to ~250 MW_e in size and firing low- to medium-sulfur coals (i.e., coals with a sulfur content of 2% or lower) may use LSD; and (2) plants larger than 250 MW_e and firing medium- to high-sulfur coals (i.e., coals with a sulfur content of 2% or higher) may use either LSFO or MEL.     

HISTORY of the Air Pollution Control Association

Bottom ash is a waste material from coal-fired power plants, and it is known to contain elements that are potentially toxic at high concentration levels when disposed in landfills. This study investigates the use of bottom ash as a partial substitute sorbent for wet flue gas desulfurization (FGD) processes by focusing on its leaching kinetics in adipic acid. This was studied basing on the shrinking core model that was applied to the experimental data obtained by the authors presented at the International Conference on Industrial, Manufacturing, Automation and Mechanical Engineering, Johannesburg, South Africa, November 27–28, 2013) on dissolution of bottom ash. The leaching rate constant was obtained from different reaction variables, namely, temperature, pH, acid concentration, and solid-to-liquid ratio, that could affect the leaching process. The solid sample of bottom ash was characterized at different leaching periods using X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that solid-to-liquid ratio had a significant effect on the leaching rate constant when compared with other variables. The leaching kinetics showed that diffusion through the product layer was the rate-controlling step during leaching, and the activation energy for the process was found to be 18.92 kJ/mol.

Implications:?The use of coal bottom ash waste as a sorbent substitute in wet flue gas desulfurization (FGD) has both economic and environmental advantages. This is because it is a waste from coal-fired thermal power plant and this study has proven that it can leach out a substantial amount of calcium ions for wet FGD process. This will abate anthropogenic pollution due to landfill disposal of bottom ash wastes and also reduce sulfur dioxide emissions.     

中国燃煤锅炉烟气脱硫技术的发展前景

本文在综述我国燃煤中小型锅炉和电站锅炉烟气脱硫技术现状的基础上，分析了我国燃煤锅炉烟气脱硫技术的发展前景．分析结果指出：我国中小型燃煤锅炉烟气脱硫技术近期是以完善湿法脱硫技术为主，远期将大力发展干法脱硫技术；在电站锅炉烟气脱硫方面，规模较小的电站锅炉将以喷雾干燥法为主要发展方向，大型电站锅炉近期仍以湿式石灰石－石膏法为主，远期将大力发展电子束辐照氨法脱硫脱硝技术。     

Mercury Mass Balances: A Case Study of Two North Dakota Power Plants

ABSTRACT

The Energy & Environmental Research Center (EERC) conducted a mercury-sampling program to provide data on the quantity and forms of Hg emitted and on the Hg removal efficiency of the existing air pollution control devices at two North Dakota power plants—Milton R. Young Station and Coal Creek Station. Minnkota Power Cooperative, Great River Energy, the North Dakota Industrial Commission, and EPRI funded the project. The primary objective was to obtain accurate measurements of Hg released from each plant, as verified by a material balance. A secondary objective was to evaluate the ability of a mercury continuous emission monitor (CEM) to measure total Hg at the stack.

At both plants, speciated Hg measurements were made at the inlets and outlets of both the electrostatic precipi-tators (ESPs) and the flue gas desulfurization (FGD) systems. A Semtech Hg 2000 (Semtech Metallurgy AB) mercury CEM was used to measure the total Hg emissions at the stack in real time. Using these measurements and plant data, the measured Hg concentrations in the coal, FGD slurries, and ESP ash, a Hg mass flow rate was calculated at each sampling location. Excellent Hg mass balances were obtained (±15%). It was also found that the Hg was mostly in the elemental phase (~90%), and the small amount of oxidized Hg that was generated was removed by the FGD systems.

Insignificant amounts of particulate-bound Hg were measured at both plants. However, 10-20% of the elemental Hg measured prior to the ESP was converted to oxidized Hg across the ESP. The data show that, at these facilities, almost all of the Hg generated is being emitted into the atmosphere as elemental Hg. Local or regional deposition of the Hg emitted from these plants is not a concern. However, the Hg does become part of the global Hg burden in the atmosphere. Also, the evidence appears to indicate that elemental Hg is more difficult to remove from flue gas than oxidized Hg is.     

Investigation of a Mercury Speciation Technique for Flue Gas Desulfurization Materials

Abstract

Most of the synthetic gypsum generated from wet flue gas desulfurization (FGD) scrubbers is currently being used for wallboard production. Because oxidized mercury is readily captured by the wet FGD scrubber, and coal-fired power plants equipped with wet scrubbers desire to benefit from the partial mercury control that these systems provide, some mercury is likely to be bound in with the FGD gypsum and wallboard. In this study, the feasibility of identifying mercury species in the FGD gypsum and wallboard samples was investigated using a large sample size thermal desorption method. Potential candidates of pure mercury standards including mercuric chloride (HgCl₂), mercurous chloride (Hg₂Cl₂), mercury oxide (HgO), mercury sulfide (HgS), and mercuric sulfate (HgSO₄) were analyzed to compare their results with those obtained from FGD gypsum and dry wallboard samples. Although any of the thermal evolutionary curves obtained from these pure mercury standards did not exactly match with those of the FGD gypsum and wallboard samples, it was identified that Hg₂Cl₂ and HgCl₂ could be candidates. An additional chlorine analysis from the gypsum and wallboard samples indicated that the chlorine concentrations were approximately 2 orders of magnitude higher than the mercury concentrations, suggesting possible chlorine association with mercury.     

Long-term monitoring and modeling of polychlorinated dibenzo-p-dioxins and dibenzofurans from municipal solid waste incinerators and surrounding area in northern Taiwan

Municipal solid waste incinerators (MSWIs) have long been the major contributors of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) to ambient air in Taiwan. After stringent MSWI emission standards were introduced in 2001, the long-term continuous monitoring of flue gas and ambient air quality became necessary to ensure the effectiveness of the related control strategies. Three MSWIs and the surrounding ambient air were investigated in the current study for PCDD/F characteristics during 2006 to 2011. The average concentrations in the flue gas ranged from 0.008?~?0.0488 ng I-TEQ/Nm³, which is much less than the emission standard in Taiwan (0.1 ng I-TEQ/Nm³) (I-TEQ is the abbreviation of International Toxic Equivalent). This led to extremely low levels in the ambient air, 0.0255 pg I-TEQ/Nm³, much less than the levels seen in most urban areas around the world. Additionally, the results obtained using the Industrial Source Complex Short-Term Dispersion Model (ISCST3) indicate that the PCDD/F contributions from the three MSWIs to the ambient air were only in the range from 0.164?~?0.723 %. Principal component analysis (PCA) showed that the PCDD/Fs in the air samples had very similar characteristics to those from mobile sources. The results thus show that stringent regulations have been an effective control strategy, especially for urban areas, such as Taipei City.     

Eliminating Reheat from Existing FGD Systems

The Clean Air Act Amendments of the early 1970_s required coal burning utilities to reduce their emissions of sulfur dioxide. Lime or limestone based wet systems were employed for flue gas desulfurization (FGD). These systems reduced flue gas temperatures to below acid dew point conditions. Concerned about the prospect of ductwork exposed to a saturated, acid-rich environment, most utilities turned to stack gas reheat (SGR) to increase flue gas temperatures. By 1980, 82 percent of all FGD facilities employed SGR. Today there are about 130 FGD systems of which 101 employ some form of stack gas reheat.     

Environmental Irradiation Test Facility

Results from a detailed analysis of sulfur dioxide (SO₂) reductions achievable through “deep” physical coal cleaning (PCC) at 20 coal-fired power plants in the Ohio-Indiana-Illinois region are presented here. These plants all have capacities larger than 500 MWe, are currently without any flue gas desulfurization (FGD) systems, and burn coal of greater than l%sulfur content (in 1980). Their aggregate emissions of 2.4 million tons of SO₂ per year represents 55% of the SO₂ inventory for these states. The principal coal supplies for each power plant were identified and characterized as to coal seam and county of origin, so that published coal-washability data could be matched to each supplier. The SO₂ reductions that would result from deep cleaning each coal (Level 4) were calculated using an Argonne computer model that assumes a weight recovery of 80%. Percentage reductions in sulfur content ranged from zero to 52%, with a mean value of 29%, and costs ranged from a low of $364/ton SO₂ removed to over $2000/ton SO₂ removed. Because coal suppliers to these power plants employ some voluntary coal cleaning, the anticipated emissions reduction from current levels should be near 20%. Costs then were estimated for FGD systems designed to remove the same amount of SO₂ as was achieved by PCC through the use of partial scrubbing with bypass of the remaining flue gas. On this basis, PCC was more cost-effective than FGD for about 50% of the plants studied and had comparable costs for another 25% of the plants. Possible governmental actions to either encourage or mandate coal cleaning were identified and evaluated     

The dissolution kinetics of industrial brine sludge wastes from a chlor-alkali industry as a sorbent for wet flue gas desulfurization (FGD)

The disposal of industrial brine sludge waste (IBSW) in chlor-alkali plants can be avoided by utilization of IBSW as a sorbent in wet flue gas desulfurization (FGD). The shrinking core model was used to determine the dissolution kinetics of IBSW, which is a vital step in wet FGD. The effects of solid-to-liquid ratio (m/v), temperature, pH, particle size, and stirring speed on the conversion and dissolution rate constant are determined. The conversion and dissolution rate constant decreases as the pH, particle size, and solid-to-liquid ratio are increased and increases as the temperature, concentration of acid, and stirring speed are increased. The sorbents before and after dissolution were characterized using x-ray fluorescence (XRF), x-ray diffraction (XRD), and scanning electron microscopy (SEM). An activation energy of 7.195 kJ/mol was obtained and the product layer diffusion model was found to be the rate-controlling step.

Implications: The use of industrial brine sludge waste as an alternative sorbent in wet flue gas desulfurization can reduce the amounts of industrial wastes disposed of in landfills. This study has proved that the sorbent can contain up to 91% calcium carbonate and trace amounts of sulfate, magnesium, and so on. This can be used as new sorbent to reduce the amount of sulfur dioxide in the atmosphere and the by-product gypsum can be used in construction, as a plaster ingredient, as a fertilizer, and for soil conditioning. Therefore, the sorbent has both economic and environmental benefits.     

Anion-Exchange Resin-Based Desulfurization and Dechlorination of Spent Sorbent Material

Abstract

Emissions of acid gases such as SO₂ and HCI/CI₂ from energy conversion or waste incineration facilities are unacceptable. Under the various regulations, the emissions of such acid gases are regulated by the U.S. Environmental Protection Agency (EPA). Alkali metal sorbents can remove these acid gases more efficiently than the lime/limestone type sorbents used in the conventional flue gas desulfurization (FGD) systems. However, the resulting alkali metal sulfate and chloride are unsuitable for landfill disposal because they are water-soluble and can potentially leach into groundwater, altering the soil pH. Replacing the (virgin) sorbent material is expensive. Hence, it is desirable that the spent sorbent materials obtained from such emissions control systems be converted to sulfur- and chlorine-free forms, so that they can be reused. The weak-base, anionexchange resin-based desulfurization concept, developed and tested at the University of Tennessee Space Institute (UTSI), can also simultaneously remove sulfur- and chlorine- containing species from such spent sorbent materials. Under the U.S. Department of Energy’s (DOE) sponsorship, bench scale studies have been carried out at UTSI to evaluate the feasibility of removing sulfur- and chlorine-containing species using this resin-based concept. Efforts have also been made to enhance the candidate resins’ performance by carrying out the resin exhaustion step under CO₂ static pressure and by using suitable pH buffering agents, such as low-molecular weight organic acids. Preliminary cost estimates for a regeneration scheme employing reactivated alkali metal-based spent sorbent material using the ion-exchange resin-based concept seem attractive and comparable to currently available options. After further development, this low-cost, simple process can be easily integrated into alkali metal sorbent-based flue gas desulfurization and acid gas emission control systems.     

An Analysis of Extinction Coefficients of Particles and Water Moisture in the Stack after Flue Gas Desulfurization at a Coal-Fired Power Plant

ABSTRACT

Two important factors that affect in-stack opacity—light extinction by emitted particles and that by water moisture after a flue gas desulfurization (FGD) unit—are investigated. The mass light extinction coefficients for particles and water moisture, k _p and k _w, respectively, were determined using the Lambert-Beer law of opacity with a nonlinear least-squares regression method. The estimated k _p and k _w values vary from 0.199 to 0.316 m²/g and 0.000345 to 0.000426 m²/g, respectively, and the overall mean estimated values are 0.229 and 0.000397 m²/g, respectively. Although k _w is 3 orders of magnitude smaller than k _p, experimental results show that the effect on light extinction by water moisture was comparable to that by particles because of the existence of a considerable mass of water moisture after a FGD unit. The mass light extinction coefficient was also estimated using Mie theory with measured particle size distributions and a complex refractive index of 1.5-ni for fly ash particles. The k _p obtained using Mie theory ranges from 0.282 to 0.286 m²/g and is slightly greater than the averaged estimated k _p of 0.229 m²/g from measured opacity. The discrepancy may be partly due to a difference in the microstructure of the fly ash from the assumption of solid spheres because the fly ash may have been formed as spheres attached with smaller particles or as hollow spheres that contained solid spheres. Previously reported values of measured k _p obtained without considering the effects of water moisture are greater than that obtained in this study, which is reasonable because it reflects the effect of extinction by water moisture in the flue gas. Additionally, the moisture absorbed by particulate matter, corresponding to the effect of water moisture on the particulates, was clarified and found to be negligible.

IMPLICATIONS In-stack opacity is used as a surrogate for particle concentration and can be measured using light transmission meters as part of a continuous emission monitoring system. Because emission standards have become increasingly strict, FGD with wet scrubbing is generally used for coal-fired power plants. However, after a FGD unit with wet scrubbing is set up, the concentration of water moisture increases, affecting the measured opacity. This study evaluates the contributions of particles and water moisture to opacity. The results should provide useful information and can be utilized for modifying measurements for monitoring particulate emissions using opacity.     

Emissions of Polychlorinated Dibenzo-p-Dioxins and Dibenzofurans from Various Industrial Sources

Abstract

This study characterized the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) from the stack flue gases of 17 industrial sources, which were classified into 10 categories. The results show that the mean PCDD/PCDF concentration of secondary zinc smelter (Zn-S) and secondary copper smelter (Cu-S) is 2.44 ng international toxic equivalent (I-TEQ)/Nm³ (N represents normal conditions at 0 °C, 760 mmHg), which was found to be significantly greater than that of industrial waste incinerators (mean concentration = 0.15 ng I-TEQ/Nm³). These results imply that the controlling of secondary metallurgical melting processes is more important than industrial waste incineration for the reduction of PCDD/PCDF emissions. The mean emission factors of cement production, Zn-S and Cu-S, are 0.052, 1.99, and 1.73 μg I-TEQ/t product, respectively. For industrial waste incineration, the mean emission factors of waste rubber, waste liquor, waste sludge, industrial waste solid (IWI)-1, IWI-2, IWI-3, and IWI-4 are 0.752, 0.435, 0.760, 6.64, 1.67, 2.38, and 0.094 μg I-TEQ/t feed, respectively. Most of the PCDD/PCDF emission factors established in this study are less than those reported in previous studies, which could be because of the more stringent regulations for PCDD/PCDF emissions in recent years.     

Application of the Lime/Limestone Flue Gas Desulfurization Process to Smelter Gases

In this presentation, adaptation of the lime/limestone process for flue gas desulfurization (FGD) is discussed and how this process can be adapted to applications in the nonferrous smelting industry such as fugitive gases, copper reverberatory furnace gases, lead sintering gases, molybdenum roasting plant tail gases, and other weak SO₂ smelter gases. Different methods for particulate removal are also discussed with emphasis on how the particulate removal process can be integrated with the desulfurization process.     

The Importance of Maintenance for Lime Flue Gas Desulfurization Systems

The successful, reliable operation of a power plant flue gas desulfurization (FGD) system depends largely on a good program of maintenance. Identifying the FGD equipment that is most critical to an FGD system’s overall reliability or its ability to meet emission regulations plays an important role in determining the extent of a maintenance program for a particular site. FGD maintenance programs vary considerably, depending on site-specific requirements and the support of plant owners. Many owners are reluctant to spend money on FGD maintenance because an FGD system is a nonproductive part of a power plant; however, a good maintenance program can result in longer equipment life, improved equipment performance, increased system availability, better safety, and lower operating costs. This paper uses wet and dry lime FGD systems to illustrate the advantages of good maintenance and the consequences of poor maintenance. Examples of specific tasks for preventive, scheduled, planned, and emergency maintenance are described. Also, because of the importance of FGD maintenance personnel, a section on organization and training is included.