吹脱-捕集气相色谱法测定底质中易挥发性有机物

研究并建立了利用吹脱－捕集气相色谱法测定底质中易挥发性有机物的分析方法。该方法对底质中２５种易挥发性有机物进行测定。方法回收率在９６％－１０５％,最低检出浓度在０．３－１４．５μｇ／ｋｇ,变异系数在２．７％－５．３％。     

利用成组生物测试评估某城市典型污水处理工艺

设计了一组基于生物标记物的生物测试方法,并用于评价某城市4个典型污水处理工艺对水中痕量有毒有机物的去除效果.测试方法包括检测芳烃(Ah)受体效应物质生物毒性的EROD(7-乙氧基-3-异吩噁唑酮-脱乙基酶)试验、类雌激素效应物质的重组基因酵母生物毒性试验和遗传毒性物质的SOS/umu试验.结果表明,4个典型的城市污水处理工艺对Ah受体效应物质、类雌激素效应物质和遗传毒性物质都有一定的去除效果,其中A2/O处理工艺对3类物质的去除效果最明显;空气曝气活性污泥工艺对直接遗传毒性物质的去除效果较好,但对Ah受体效应物质的去除效果一般,倒置A2/O处理工艺和氧化沟处理工艺也能够较好地去除这3类物质,两种处理工艺效果相当.采用成组生物标记物方法可以对城市污水中的痕量有毒有机物进行毒性筛选或测试,适用于水处理工艺的风险评价.     

水中有机成分及其对饮用水质的影响

微量有机污染物和氯化消毒副产物对饮用水构成直接威胁,是饮用水中要重点控制的;天然大分子有机物对水质构成间接影响,导致胶体稳定性提高、增加药耗;藻类和代谢产物影响常规处理工艺效果,对水质产生不良影响。     

固定源废气高浓度挥发性有机物的检测方法研究

中国挥发性有机物(VOCs)的污染日趋严重,许多重点排污行业VOCs排放浓度高,检测难度大。现有相关标准不适合质量浓度大于10mg/m~3的高浓度VOCs的检测,采用气袋法采样,固相吸附—热脱附/气相色谱—质谱法,用两种不同样品制备方式,对某化工企业废气净化设施进口的高浓度VOCs进行了检测,用标准气体对检测方法进行了验证。结果表明,采用气袋法采样,选择合适体积的气密针直接配置样品操作简便,可行性强,重复性好,极大降低了湿度对样品配置的影响,可用于固定源废气中高浓度VOCs的测定。     

餐饮业油烟气排放量的重量法监测

通过试验提出了一种监测餐饮业油烟气的方法，方法首次以单位体积油烟气中总有机物的质量来表示油烟气在空气中的浓度。通过试验选择了最佳监测条件；以石油醚作吸收剂，用ＫＢ－６Ａ型或ＴＭＰ－１５００型空气采样器，控制流量在０．４Ｌ／ｍｉｎ，采集油烟气，并在４０℃时挥发掉吸收剂，经称量得到监测结果，该法所需仪器和试剂简单，并在实际监测中得到了预期的结果。     

石油类污染地下水中挥发性有机物低温生物降解性能的研究

针对地下水石油类污染的问题,从某污染场地土壤中筛选驯化出了适用于处理挥发性有机物的3株低温高效降解菌,并以苯和萘作为特征组分考察了pH、DO、温度、氮磷等因素对降解效果的影响;实验结果表明,在8℃左右的地下环境中,DO和氮磷的含量对污染物的降解影响较大;在pH 7.5、DO＞4 mg/L和投加氮磷的条件下,18 d内降...     

MIEX吸附与K2FeO4预氧化协同净水效果

针对K2FeO4和MIEX两种备受关注的净水技术,系统研究了二者在净水性能方面的差异以及可能存在的协同效应,分别考察了K2FeO4、MIEX,以及K2FeO4-MIEX联合处理对DOC和UV254的去除效率;通过三维荧光光谱、亲疏水性和凝胶色谱分析,考察了两种技术对不同种类、不同亲疏水性以及不同分子质量有机物的去除规律...     

淀山湖沉水植物死亡分解过程中营养物质的释放

测定了上海淀山湖5种常见沉水植物的营养成分含量及其死亡后在好氧(DO>3.5 mg/L)或低氧(DO<3.5 mg/L)状态下分解释放TN、TP和有机物(以高锰酸盐指数计,下同)等营养物质的动态过程,并对营养物质释放强度与营养成分含量的相关性进行了分析.结果表明, 5种沉水植物中,金鱼藻的TN和TP含量最高,质量分数分别为(4.07±0.22)%和(0.99±0.09)%;好氧状态下TN和有机物的释放强度大于低氧状态,两种状态下TP的释放强度没有显著差异;TP的释放比TN快,一般需10 d左右,而TN和有机物的释放分别需要29 d和20 d左右;在好氧状态下,NO-2-N、NO-3-N和可溶性总磷酸盐的平均释放强度与植物TN含量呈显著正相关(p<0.05),NH 4-N的平均释放强度与植物TP含量呈显著正相关(p<0.05);在低氧状态下,NO-2-N的平均释放强度与植物TN含量、NO-3-N的平均释放强度与植物TP含量分别呈显著正相关(p<0.05);有机物的平均释放强度与植物TP含量呈极显著负相关(p<0.01).     

pH对电解处理垃圾渗滤液的影响

在不同的pH值条件下对氯离子和重金属离子含量不同的渗滤液和邻硝基苯酚人工模拟废水进行了电解处理,着重考察了不同pH值条件下氯离子浓度和重金属离子种类对有机物电解去除效果的影响。结果表明,电解处理过程中, pH值对有机物电解去除效果的影响与渗滤液的水质有关,尤其与渗滤液中氯离子和重金属离子浓度以及重金属离子种类有关。在pH＝2的条件下电解处理氯离子和重金属离子含量均很低的渗滤液,有利于有机物的氧化去除;在pH=9的条件下电解处理氯离子和重金属离子浓度均较高的渗滤液,其COD的电解去除效果最好;在pH=2或pH=12的条件下电解处理氯离子浓度高而重金属离子浓度低的渗滤液,能促进有机物的氧化分解。在一定浓度范围内,渗滤液中无机变价离子的组成不同,电解处理垃圾渗滤液的最佳pH值也不同。     

我国有机物污染场地土壤修复技术的专利计量分析

以我国公开的691项有机物污染场地土壤修复技术专利为依据,分析研究了有机物污染场地土壤修复技术的发展趋势和进展,同时对化学氧化修复技术、生物修复技术、热脱附技术、淋洗技术等的研究进展进行分析,总结了目前国内有机物污染场地修复专利技术发展现状,并提出了今后的发展方向,以期为我国今后开展相关修复技术的研究与应用提供参考。结果显示:我国有机物污染场地土壤修复技术相关专利于2010年后开始快速发展,研究创新点基本集中于高效技术的开发、节能以及二次污染的防治;热脱附技术在该领域应用广泛;氧化修复技术的开发是2017年的技术发展特点,具有一定的研究前景;而联合多种修复技术更能灵活地适用于实际场地修复的需要,其已成为重要的研究趋势。     

Biodegradability oriented treatability studies on high strength segregated wastewater of a woolen textile dyeing plant

Textile dyeing and finishing industry involves considerable amount of water usage as well as polluted and highly colored wastewater discharges. Biological treatability by means of mineralization, nitrification and denitrification of high strength woolen textile dye bathes, first- and second-rinses is presented. COD fractionation study was carried out and kinetic parameters were determined. Biodegradability of organic compounds in highly loaded composite wastewater after segregation and the effluent of applied biological treatment of high strength composite wastewater were measured by determining oxygen consumption rates. The results were used in terms of assessing an alternative method for inert COD fractionation. The study implied that about 80% soluble COD, 50% color and 75% toxicity reduction were possible by single sludge biological processes. Sixteen per cent of total COD was found to be initially inert. Inert fraction was increased to 22% by production of soluble and particulate microbial products through biological treatment.     

废水生物处理出水中溶解性微生物产物的形成机制与特征

废水生物处理出水中的溶解性微生物产物(SMP)主要产生于基质降解和微生物的内源呼吸过程,它的存在是影响生物处理出水水质和有机物去除率的一个重要因素,已引起人们的普遍关注.简单阐述了SMP的定义,详细探讨了废水生物处理出水中溶解性微生物产物的形成机制与特征.     

Semi-specific Microbacterium phyllosphaerae-based microbial sensor for biochemical oxygen demand measurements in dairy wastewater

Although the long incubation time of biochemical oxygen demand (BOD₇) measurements has been addressed by the use of microbial biosensors, the resulting sensor-BOD values gained from the measurements with specific industrial wastewaters still underestimates the BOD value of such samples. This research aims to provide fast and more accurate BOD measurements in the dairy wastewater samples. Unlike municipal wastewater, wastewater from the dairy industry contains many substrates that are not easily accessible to a majority of microorganisms. Therefore, a bacterial culture, Microbacterium phyllosphaerae, isolated from dairy wastewater was used to construct a semi-specific microbial biosensor. A universal microbial biosensor based on Pseudomonas fluorescens, which has a wide substrate spectrum but is nonspecific to dairy wastewater, was used as a comparison. BOD biosensors were calibrated with OECD synthetic wastewater, and experiments with different synthetic and actual wastewater samples were carried out. Results show that the semi-specific M. phyllosphaerae-based microbial biosensor is more sensitive towards wastewaters that contain milk derivates and butter whey than the P. fluorescens-based biosensor. Although the M. phyllosphaerae biosensor underestimates the BOD₇ value of actual dairy wastewaters by 25–32 %, this bacterial culture is more suitable for BOD monitoring in dairy wastewater than P. fluorescens, which underestimated the same samples by 46–61 %.     

Effect of sulfate reduction activity on biological treatment of hexavalent chromium [Cr(VI)] contaminated electroplating wastewater under sulfate-rich condition

Electroplating wastewater (EW) containing heavy metals was treated by a two-stage packed-bed reactor system. The EW was highly contaminated with hexavalent chromium and other heavy metals as well as sulfate because sulfuric acid had been mainly used to polish the surface of metals to be electroplated. This acidic EW was effectively neutralized in an alkaline reactor where limestone had been packed. The neutralized wastewater together with organic wastewater from a starch-processing factory (SPW) was fed to a bioreactor packed with waste biomass. The SPW was used to supplement the electron donor in the sulfidogenic bioreactor. During the whole operation, we investigated the stoichiometry of electron to see what could be a major factor to remove Cr in the wastewater. The removal rates of sulfate and Cr(VI) were dependent on the consumption rate of organic materials in the wastewater. The stoichiometric studies also showed that about 63% of electrons from oxidation of organic materials were used to reduce sulfate. When the electrons of sulfide oxidation to elemental sulfur was at least 1.3 times higher than that of Cr(VI) reduction to Cr(III), Cr(VI) was completely removed. This result suggests that Cr(VI) reduction can be expected to take place under sulfate-rich anaerobic conditions, and sulfide produced by sulfate reducing bacteria could be used to immobilize soluble chromium through Cr(VI) reduction.     

羧甲基壳聚糖的制备及絮凝性能探讨

制备了具有水溶性、无毒羧甲基壳聚糖（以下简称NOCC），将其作为絮凝剂与聚丙烯酰胺（PAM）一道处理生活污水，通过测定其沉降时间，沉降絮体高度，沉降速度，沉降后溶液透光率等参数，表征了其絮凝能力，提出了普遍认为聚丙烯酰胺处理一般污水具有良好絮凝能力的不同看法，为壳聚糖的开发利用做了有益的探索。     

废水COD 4种物化表征方法的比较与评估

为了确定废水COD组分表征的物化分析方法,对0.1μm滤膜过滤、0.45μm滤膜过滤、絮凝和絮凝+0.45μm滤膜过滤4种方法进行了实验比较和评估。结果表明:某些材料的滤膜会因"COD溶出"而影响表征结果;4种方法分离废水的重现性都很好,相互没有明显区别;物化分离对废水快速可生物降解COD(SS)没有影响,但4种方法得到的处理液中可生物降解COD仍含降解速率明显不同的组分,其中SS仅占35%～45%。因此,物化方法不能合理表征SS;絮凝+0.45μm滤膜过滤速度快、干扰少、分离机理与活性污泥系统类似,更适用于废水溶解性惰性COD组分(SI)表征。     

太阳能光伏废水处理设施脱氮功能优化实例

某太阳能光伏企业的生产废水约4000 m³/d,废水中的主要污染物是少量的氟离子和大量硝态氮,原废水工艺中缺少去除硝态氮的功能。在原废水处理设施基础上,将生化处理工艺优化为“A/O反硝化”工艺,增加碳源投加设备。工程实践表明,工艺优化后,硝态氮得以有效去除,TN去除率达到95%,出水水质达到《电池工业污染物排放标准》(GB30484—2013)表2的间接标准。     

Adsorption of soluble oil from water to graphene

The toxicity of soluble oil to the aquatic environment has started to attract wide attention in recent years. In the present work, we prepare graphene according to oxidation and thermal reduction methods for the removal of soluble oil from the solution. Characterization of the as-prepared graphene are performed by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Raman spectra, Brunauer-Emmett-Teller, X-ray photoelectron spectroscopy, and contact angle analysis. The adsorption behavior of soluble oil on graphene is examined, and the obtained adsorption data are modeled using conventional theoretical models. Adsorption experiments reveal that the adsorption rate of soluble oil on graphene is notably fast, especially for the soluble diesel oil, which could reach equilibrium within 30 min, and the kinetics of adsorption is perfectly consistent with a pseudo-second-order model. Furthermore, it is determined that the adsorption isotherm of soluble diesel oil with graphene fit the Freundlich model best, and graphene has a very strong adsorption capacity for soluble diesel oil in the solution. These results demonstrate that graphene is the material that provided both good adsorptive capacity and good kinetics, implying that it could be used as a promising sorbent for soluble oil removal from wastewater.     

VFAs、TOC及COD作为生物除磷能力指标的探讨

在实际生活污水的处理中,研究了通过A/O运行模式对生物除磷过程中磷的变化情况及在厌氧释磷过程中COD、TOC与VFAs变化之间的关系。结果表明,在厌氧释磷过程中VFAs的变化更能准确地反映系统内释磷进程,实际生活污水中能直接用于磷释放的有机物含量占COD的13.33%,并且释放1 mg P所需VFAs为1.401 mg,此值明显低于前期研究结果。通过对COD、TOC和VFAs 3种组分的分析,可将实际生活污水中的有机底物分为3类:易生物降解含碳有机物、难降解的含碳有机物和水中存在的无机性还原物质,含量分别占COD的13.33%、31.7%和54.97%,其中只有13.33%的含量对生物释磷有直接作用,并可对实际生活污水除磷有指导意义。     

Online biochemical oxygen demand monitoring for wastewater process control--full-scale studies at Los Angeles Glendale wastewater plant, California.

The main objective of this investigation is to determine whether or not it would be feasible to use the measured values of biochemical oxygen demand (BOD) of wastewater obtained by an online instrument at the Los Angeles/Glendale Water Reclamation Plant (California) for controlling its activated sludge process. This investigation is part of a project to develop online BOD monitoring for process control in the City of Los Angeles wastewater treatment plants. Tests studied the Siepmann und Teutscher GmbH (ISCO-STIP Inc., Lincoln, Nebraska) BIOX-1010, which uses a bioreactor containing a culture of microbes from the wastewater to measure soluble BOD in 2 minutes. This rapid approximation to the operation of secondary treatment allows anticipation of system response. Calibration measurements allow the operators to find a conversion factor for the instrument's microprocessor to compute values of BOD that agree well with the standard 5-day BOD (BOD5) measurement, despite the differences in the details of the two testing methods. This instrument has recently been used at other wastewater treatment plants, at a number of airports in Europe and the United States to monitor runway runoff, and is also being used on waste streams at an increasing number of food processing plants. A comparison was made between the plant influent BOD values obtained by the BIOX-1010 online monitor from the end of August, 2000, to late January, 2001, and the individual and average values obtained for the same period using the standard BOD5, 20 degrees C test, to determine the effectiveness of the Biox-1010 to identify shock loads and their duration. Individual BOD estimates and averages over periods of overly high biological loads (shock loads) were compared, and the instrument readings were evaluated for their effectiveness in detecting shock loads. The results were highly satisfactory, so the instrument was used to trigger a shock-load warning alarm since late September, 2000. This allowed flow diversion and temporary storage to prevent process upsets.