Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Determination of the Burning Characteristics of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is characterized by three distinct processes, ignition, flame spread and burning rate. Although all three processes are important, ignition and burning rate are critical. The former, because it defines the potential to burn and the latter because of the inherent possibility of boilover. Burning rate is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil spill. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). Ignition has been studied to provide a tool that will serve to assess a fuels ease to ignite under conditions that are representative of oil spills. Two different techniques are used, piloted ignition when the fuel is exposed to a radiant heat flux and flash point as measured by the ASTM D56 Tag Closed Cup Test. Two different crude oils were used for these experiments, ANS and Cook Inlet. Crude oils were tested in their natural state and at different levels of weathering, showing that piloted ignition and flash point are strong functions of weathering level.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

鼓泡式反应器高径比对氨法烟气脱碳性能的影响

以N2和CO2混合气模拟燃烧烟气,研究了鼓泡反应器的高径比以及反应条件对氨法烟气脱碳性能的影响。实验结果表明:在相同高径比的条件下,CO2吸收率随氨水质量分数的增加、反应温度的升高而逐渐增大,随进气CO2体积分数和模拟烟气流量的增加而逐渐减小;CO2吸收率随高径比的增加而增大,在高径比为3.98、氨水质量分数为28%、进气CO2体积分数为10%、模拟烟气流量为1.0L/min、反应温度为40℃的条件下,CO2吸收率最高可达100%。     

Structure-biodegradation relationships of polymeric materials. 1. Effect of degree of oxidation on biodegradability of carbohydrate polymers

The biodegradability of oxidized starch and inulin has been studied in relation to the degree of periodate oxidation to dialdehyde derivatives, by measuring oxygen consumption and mineralization to carbon dioxide. A higher degree of oxidation of dialdehyde starch and dialdchyde inulin results in a lower rate at which the polymers are biodegraded. It is demonstrated that the biodegradation rate of dialdehyde inulin derivatives decreases more than that of equivalent starch derivatives. The differences in biodegradation behavior between dialdehyde starch and dialdehyde inulin, resulting from comparable modifications, are discussed in terms of conformational structure.     

Mechanism of Microbial Degradation of Slow-Release Fertilizers

Methyleneureas are condensation products of urea and formaldehyde of different molecular mass and solubility; they are used in large amounts both as resins, binders, and insulating materials for industrial applications, as well as a slow-release nitrogen fertilizer for greens, lawns, or in bioremediation processes. In the present study, the microbial breakdown of these products was investigated. The nitrogen was released as ammonia and urea, and the formaldehyde released immediately oxidized via formiate to carbon dioxide. The enzymatic mechanism of metabolization of methyleneureas was studied in microorganisms isolated from soil, which were able to use these compounds as the sole source of nitrogen for growth. A strain of the Gram-negative bacterium Ralstonia paucula (formerly Alcaligenes sp. CDC group IVc-2) completely degraded methylenediurea and dimethylenetriurea to urea, ammonia, formaldehyde, and carbon dioxide. The enzyme initiating this degradation (methylenediurease) was purified and turned out to be different from the previously described enzyme from Ochrobactrum anthropi with regard to its regulation of expression and physicobiochemical properties. Fungal degradation of methyleneureas may occur via the formation of organic acids, thus leading to a nonenzymatic degradation of methyleneureas, which are unstable under acidic conditions.     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

催化燃烧处理有机废气及催化剂中毒的防止

研究了在Ｐｔ、Ｐｄ、Ｃｅ多组分蜂窝状催化剂上乙醇、环己烷和苯的氧化性能及水蒸气对催化剂活性的影响,探讨了如何防止硫化氢和甲硫醇引起的催化剂中毒。     

不同类型清水剂处理油田含聚污水的效果对比

考察了阳离子型CWC-14、非离子型NQS-01和阴离子型AQS-08 3类清水剂对油田含聚污水的处理效果,对比了它们的作用特点和絮体性能。实验结果表明:在清水剂加入量350 mg/L、处理温度65℃、搅拌转速300 r/min、搅拌时间5 min的条件下,CWC-14、NQS-01和AQS-08对含聚污水的除油率分别为98.8%、98.0%和99.4%;NQS-01受处理温度、搅拌条件影响较大;CWC-14受污水中聚合物质量浓度影响最大。清水剂的絮体特点与其作用机理有关,CWC-14的絮凝速率最快,起效时间最短,絮体呈黏性大块状;NQS-01的絮凝速率最慢,起效时间最长,絮体呈浮油状;AQS-08的絮凝速率和起效时间适中,絮体呈松散状、流动性好。对比结果表明,非阳离子型清水剂可有效避免油田含聚污水处理过程中的黏性油泥问题。     

核能发电的特点及前景预测

核能发电具有经济、环保、安全的特点,发展和推广核电既能确保能源的可持续发展,也能满足环境保护的需要。近年来,核电发展取得了一定成绩,但其热污染和放射污染问题仍需引起重视并采取相关的措施。