Bioleaching of heavy metals from sewage sludge: A review

During the treatment of sewage, a huge volume of sludge is generated, which is disposed of on land as soil fertilizer/conditioner due to the presence of nitrogen, phosphorus, potassium and other nutrients. However, the presence of toxic heavy metals and other toxic compounds in the sludge restricts its use as a fertilizer. Over the years, bioleaching has been developed as an environmentally friendly and cost-effective technology for the removal of heavy metals from the sludge. The present paper gives an overview of the various bioleaching studies carried out in different modes of operation. The various important aspects such as pathogen destruction, odor reduction and metal recovery from acidic leachate also have been discussed. Further, a detailed discussion was made on the various technical problems associated with the bioleaching process, which need to be addressed while developing the process on a larger scale.     

Leaching characteristics of heavy metals from sewage sludge by Acidithiobacillus thiooxidans MET

An acidophilic, sulfur-oxidizing Acidithiobacillus thiooxidans MET bacterium was isolated from anaerobically digested, dewatered sewage sludge. This bacterium showed sulfur-oxidizing ability at both acidic and neutral conditions, and allowed metal leaching even at a high (130 g L(-1)) sludge solids concentration. We found that low metal leaching efficiency at high solids concentration was mainly due to an increase in buffering capacity resulting in retardation of pH reduction. Therefore, metal leaching was mainly influenced not by sludge solids concentration, but by the pH (or sulfate concentration per unit sludge mass) of the sludge solutions. The relationship between the pH of the sludge solution and the efficiency of metal leaching was obtained by quantitatively investigating the effect of pH reduction or the amount of sulfate produced per unit sludge mass on leaching of each metal. Furthermore, the relationship between total metal content in the sludge and metal leached to the solution was obtained for each metal. Such a relationship allowed estimation of leachable metal at various amounts of total metal content in sludge.     

动电技术去除城市污泥中重金属的可行性探讨

本文简要介绍了我国城市污泥的处理处置和利用现状及动电技术去除重金属的基本原理,分析动电技术处理土壤中重金属的国内外的试验研究和应用情况,对动电技术处理城市污泥中重金属的可行性进行探讨,认为动电技术去除城市污泥中的重金属具有可行性,并提出了今后研究的方向.     

Environmental risks of applying sewage sludge compost to vineyards: carbon,heavy metals,nitrogen, and phosphorus accumulation

Biosolids are applied to vineyards to supply organic matter. However, there is concern that this practice can increase the concentration of macronutrients and heavy metals in the soil, some of which can leach. We evaluated the environmental hazard of sewage sludge compost applied in March 1999 at 10, 30, and 90 Mg ha-1 fresh weight in a vineyard in southeastern France. Soil organic matter increased in all plots by 3 g kg-1 18 mo after the amendment. Neither total nor available heavy metal concentrations increased in the soil. Mineral nitrogen (N) in the topsoil of amended plots of 10, 30, and 90 Mg ha-1 increased by 5, 14, and 26 kg (NO3(-)-N + NH4(+)-N) ha-1, respectively, the first summer and by 2, 5, and 10 kg (NO3(-)-N + NH4(+)-N) ha-1, respectively, the second summer compared with controls. At the recommended rate, risks of N leaching is very low, but phosphorus (P) appeared to be the limiting factor. Phosphorus significantly increased only in plots amended with the highest rate in the topsoil and subsoil. At lower rates, although no significant differences were observed, P added was greater than the quantities absorbed by vines. In the long run, P will accumulate in the soil and may reach concentrations that will pose a risk to surface waters and ground water. Therefore, although the current recommended rate (10 Mg ha-1) increased soil organic matter without the risk of N leaching, total sewage sludge loading rates on vineyards should be based on P concentrations.     

Use of constructed wetland for the removal of heavy metals from industrial wastewater

This study was conducted to investigate the effectiveness of a continuous free surface flow wetland for removal of heavy metals from industrial wastewater, in Gadoon Amazai Industrial Estate (GAIE), Swabi, Pakistan. Industrial wastewater samples were collected from the in-let, out-let and all cells of the constructed wetland (CW) and analyzed for heavy metals such as lead (Pb), cadmium (Cd), iron (Fe), nickel (Ni), chromium (Cr) and copper (Cu) using standard methods. Similarly, samples of aquatic macrophytes and sediments were also analyzed for selected heavy metals. Results indicate that the removal efficiencies of the CW for Pb, Cd, Fe, Ni, Cr, and Cu were 50%, 91.9%, 74.1%, 40.9%, 89%, and 48.3%, respectively. Furthermore, the performance of the CW was efficient enough to remove the heavy metals, particularly Cd, Fe, and Cu, from the industrial wastewater fed to it. However, it is suggested that the metal removal efficiency of the CW can be further enhanced by using proper management of vegetation and area expansion of the present CW.     

Biosorption of heavy metals by activated sludge and their desorption characteristics

The biosorption of different metals (Cu2+, Cd2+, Zn2+, Ni2+ and Pb2+) was investigated using activated sludge. The optimum pH was 4 for Cd, Cu and Pb sorption and 5 for Ni and Zn. Biomass metal uptake clearly competed with protons present in the aqueous medium, making pH an important variable in the process. Protons consumed by biomass in control tests versus protons exchange in biosorption tests confirmed a maximum exchange between metal cations and protons at pH 2. The study of the influence of biomass concentration revealed that the amount of protons released from biomass increased with biomass concentration. This would confirm the hypothesis of ion exchange between both types of ions. The application of the Langmuir and Freundlich models showed a better fitting of experimental data to the first model. The maximum sorption uptake of the studied metals by the activated sludge showed the following decreasing order: Pb>Cu>CdZn>Ni. Desorption experiments showed that HCl was a good eluent for the five metals tested, particularly at low pH values (1 and 2). At pH 3 or 4 the desorption yield was significantly lower. However, its use did not allow the reuse of biomass in subsequent loading and unloading cycles. EDTA was also a good desorption agent, achieving the total recovery for the five metals tested at a concentration of 1mM, with the advantage that biomass could be reused for three sorption-desorption cycles.     

Bacterial pretreatment enhances removal of heavy metals during treatment of post-methanated distillery effluent by Typha angustata L

A combination of bacterial pretreatment followed by free water surface flow through wetland plants was investigated to determine its effect on removal of heavy metals in bioremediation of post-methanated distillery effluent (PMDE). The bacterial pretreatment was intended to transform the metal complexes and organic pollutants into simpler, biologically assimilable molecules. The 10% and 30% v/v concentrations of PMDE favored luxuriant bacterial growth; the 50% concentration supported less growth, whereas the undiluted effluent (i.e., 100%) supported very little bacterial growth. The use of bacterial pretreatment combined with the constructed wetland system greatly increase the overall bioaccumulation of all heavy metals by the plants compared with the control treatment. However, the integration of bacterial pretreatment of PMDE with the Typha angustata resulted in enhanced removal of Cd (34.02–61.50% increase), Cr (35.90–57.60% increase), Cu (32.88–54.22% increase), Fe (32.50–51.26% increase), Mn (35.99–82.85% increase), Ni (35.85–59.24% increase), Pb (33.45–59.51% increase) and Zn (31.95–53.70% increase) compared with a control that lacked this pretreatment. In addition to the bioaccumulation of these heavy metals, several physico-chemical parameters also improved at the 30% effluent concentration: color, BOD, COD, phenol and total nitrogen decreased by 98.33%, 98.89%, 98.50%, 93.75% and 82.39%, respectively, after 7 days of free water surface flow treatment. The results suggest that bacterial pretreatment of PMDE, integrated with phytoremediation will improve the treatment process of PMDE and promote safer disposal of this waste.     

Experimental investigation of adsorption capacity of anthill in the removal of heavy metals from aqueous solution

In the present work, the adsorption capacity of anthill was investigated as a low‐cost adsorbent to remove the heavy metal ions, lead (II) ion (Pb²⁺), and zinc (II) ion (Zn²⁺) from an aqueous solution. The equilibrium adsorption isotherms of the heavy metal ions were investigated under batch process. For the study we examined the effect of the solution's pH and the initial cations concentrations on the adsorption process under a fixed contact time and temperature. The anthill sample was characterized using a scanning electron microscope (SEM), X‐ray fluorescence (XRF), and Fourier transform infrared (FTIR) techniques. From the SEM analysis, structural change in the adsorbent was a result of heavy metals adsorption. Based on the XRF analysis, the main composition of the anthill sample was silica (SiO₂), alumina (Al₂O₃), and zirconia (ZrO₂). The change in the peaks of the spectra before and after adsorption indicated that there was active participation of surface functional groups during the adsorption process. The experimental data obtained were analyzed using 2‐ and 3‐parameter isotherm models. The isotherm data fitted very well to the 3‐parameter Radke–Prausnitz model. It was noted that Pb²⁺ and Zn²⁺ can be effectively removed from aqueous solution using anthill as an adsorbent.     

Treatment and reuse of sewage sludge

Sewage sludge was treated using composting, fixed-bed and stirred anaerobic digesters. The treatment performance in terms of the physico chemical parameters, bacterial indicators and pathogenic forms were assessed. In addition, the biogas production rate was recorded in the case of anaerobic digesters. Composting of the sewage sludge increased its total solids from 39 to 93% after 6 weeks, while the reduction in organic matter was 40% and the total nitrogen and phosphorus contents increased by 22 and 30%, respectively. Complete removal of salmonellae and faecal coliforms occurred, so that the composted sludge could be used as a soil conditioner and fertilizer. The results of the anaerobic treatment indicated that an organic load of 4.8kg COD m–3 per day achieved the best operating conditions for either the stirred or fixed-bed digester. The mean percentage removals of COD, BOD, faecal coliforms, faecal streptococci and the biogas production rate for the stirred digester were 53, 53, 24 and 29% and 259 L kg–1 COD per day, respectively. The corresponding mean percentage removals and production rate for the experiments with a fixed-bed digester were 61, 62, 33 and 35% and 328 L kg–1 COD per day, respectively. Improvements in the BOD and faecal coliform reductions and the gas production rate of 17, 38 and 21%, respectively, were achieved due to the presence of media (Berl saddles) in the fixed-bed digester. The microbial content of the anaerobically treated sludge is too high to be used as a fertilizer, while that of the composted sludge is low enough for such use.     

Changes in the nature of sewage sludge organic matter during a twenty-one-month incubation

Six sewage sludges from five sewage treatment plants in Australia were incubated for up to 21 months. Carbon losses at the end of the 21-mo incubation varied substantially. The remaining organic matter was isolated by treatment with hydrofluoric acid (HF) and characterized using a range of solid-state (13)C nuclear magnetic resonance (NMR) spectroscopic techniques. By every measure (signal distribution in cross polarization [CP] and Bloch decay [BD] spectra, carbon NMR observability determined by spin counting, and the appearance of proton spin relaxation editing subspectra), the chemical composition of the residual organic matter appeared to be little different from that of the original sludges, even for those sludges that experienced the greatest carbon losses. Importantly, these NMR properties distinguish sewage sludge organic matter from soil organic matter. Thus, it should be possible to follow the decomposition of sewage sludge organic matter applied to soils in the field using solid-state (13)C NMR spectroscopy.     

Phosphorus runoff from sewage sludge applied to different slopes of lateritic soil

Sewage sludge (SS) applied to sloping fields at rates that exceed annual forest nutrient requirements can be a source of phosphorus (P) in runoff. This study investigates the effects of different slopes (18, 27, 36, and 45%) on P in runoff from plots amended with SS (120 Mg ha). Lateritic soil (pH 5.2) was exposed to five simulated rainfalls (90 mm h) on outdoor plots. When sludge was broadcast and mixed with surface soils, the concentrations and loss in runoff of total P in the mixed sample (MTP), total P in the settled sample (STP), total particulate P (TPP), total suspended P (TSP), and total dissolved P (TDP) were highest at 1 or 18 d after application. Initially, pollution risks to surface waters generally increased to different degrees with steeper slopes, and then diminished gradually with dwindling differences between the slopes. The runoff losses coefficient of MTP increased in the order 36 > 45 > 27 > 18%. The initial event (1 and 18 d) accounted for 67.0 to 83.6% of total runoff P losses. Particulate fraction were dominant carriers for P losses, while with the lower slopes there was higher content of P per unit particulate fraction in runoff. Phosphorus losses were greatly affected by the interaction of sludge-soil-runoff and the modification of soil properties induced by sludge amendment. It is recommended to choose lower slopes (<27%) to reduce risk of P losses. Thus, the risk of application sludge to sloping fields in acid soils should be studied further in the field under a wider diversity of conditions.     

Influence of vegetation on the removal of heavy metals and nutrients in a constructed wetland

A free water surface wetland was built to treat wastewater containing metals (Cr, Ni, Zn) and nutrients from a tool factory in Argentina. Water, sediment and macrophytes were sampled in the inlet and outlet area of the constructed wetland during three years. Three successive phases of vegetation dominance were developed and three different patterns of contaminant retention were observed. During the Eichhornia crassipes dominance, contaminants were retained in the macrophyte biomass; during the E. crassipes+Typha domingensis stage, contaminants were retained in the sediment and in the T. domingensis dominance stage, contaminants were retained in sediment and in the macrophyte biomass. Removal efficiency was not significantly different among the three vegetation stages, except for NH(4)(+) and i-P(diss). Because of its highest tolerance, T. domingensis is the best choice to treat wastewater of high pH and conductivity with heavy metals, a common result from many industrial processes.     

Evaluation of biogas production from seaweed in batch tests and in UASB reactors combined with the removal of heavy metals

Seaweed can be anaerobically digested for the production of energy-rich methane. However, the use of seaweed digestate as a fertilizer may be restricted because of the high heavy metal content especially cadmium. Reducing the concentration of heavy metals in the digestate will enable its use as a fertilizer. In this laboratory-scale study, the potential of seaweed and its leachate in the production of methane were evaluated in batch tests. The effect of removing the heavy metals from seaweed leachate was evaluated in both batch test and treatment in an upflow anaerobic sludge blanket (UASB) reactor. The heavy metals were removed from seaweed leachate using an imminodiacetic acid (IDA) polyacrylamide cryogel carrier. The methane yield obtained in the anaerobic digestion of seaweed was 0.12 N l CH₄/g VS_added. The same methane yield was obtained when the seaweed leachate was used for methane production. The IDA-cryogel carrier was efficient in removing Cd²⁺, Cu²⁺, Ni²⁺ and Zn²⁺ ions from seaweed leachate. The removal of heavy metals in the seaweed leachate led to a decrease in the methane yield. The maximum sustainable organic loading rate (OLR) attained in the UASB reactor was 20.6 g tCOD/l/day corresponding to a hydraulic retention time (HRT) of 12 h and with a total COD removal efficiency of about 81%. Hydrolysis and treatment with IDA cryogel reduced the heavy metals content in the seaweed leachate before methane production. This study also demonstrated the suitability of the treatment of seaweed leachate in a UASB reactor.     

Effects of impurities on the removal of heavy metals by natural limestones in aqueous systems

Effects of impurities on the removal of heavy metals by natural limestones in aqueous solutions were studied by evaluating various factors including limestone concentration, pH, contact time and temperature. Solutions of Pb(II), Cd(II), Cu(II) and Zn(II), prepared from chloride reagents at a concentration of 10 mg/L, were studied in a batch method. Four natural limestone samples, collected from the Campanian-Maastrichtian limestone beds in Tunisia, were used as adsorbents. Sorption experiments indicated that high removal efficiencies could be achieved. Limestone samples containing impurities, such as silica, iron/aluminum oxides and different kinds of clay minerals, demonstrated enhanced sorption capacity, nearing 100% removal in some cases. Kinetic experiments showed that the sorption of metal ions occurred rapidly at a low coverage stage, and that solutions were nearly at equilibrium after 60 min. Data trends generally fit pseudo-second order kinetic, and intra-particle diffusion, models. The following conditions were found to promote optimum, or near-optimum, sorption of heavy metals: 1) contact time of more than 60 min, 2) pH = 5, 3) >3 g/L limestone concentration and 4) T = 35 °C. The results of this study suggest that the limestones from northern Tunisia, that contain higher amounts of silica and iron/aluminum oxides, are promising adsorbents for the effective removal of toxic heavy metals from wastewaters.     

Cadmium content of wheat grain from a long-term field experiment with sewage sludge

Grain Cd concentrations were determined in the wheat (Triticum aestivum L.) cultivars Soissons, Brigadier, and Hereward grown in 1994,1996, and 1999, respectively, in soils of a long-term field experiment to which sewage sludges contaminated with Zn, Cu, Ni, or Cr had previously been added. Soil pore water soluble Cd and free Cd2+ increased linearly with increasing total soil Cd (R2=0.82 and 0.84, respectively; P<0.001). Similarly, soil pore water free Cd2+ increased linearly with increasing soil pore water soluble Cd (R2=0.98; P<0.001). There was no evidence of a plateau in soil pore water Cd concentrations with increasing soil Cd concentrations. Grain Cd concentrations were significantly correlated with total soil Cd (P<0.001), soil pore water Cd (P<0.001), and free Cd2+ (P<0.001). A slight curvilinear relationship between grain Cd and soil Cd was apparent, but there was no plateau, even at the maximum soil Cd concentration of about 2.7 mg kg(-1). The relationship between soil pore water Cd and grain Cd was linear for all three cultivars. The slopes were in the order 1994 > 1996 > 1999, with more Cd being taken up into the grain by Soissons grown in 1994, and least by Hereward grown in 1999. For Soissons, Cd concentration in the grain greater than the EU limit (0.24 mg kg(-1) dry wt.) occurred at soil Cd less than the current UK limit of 3 mg kg(-1) for soils receiving sewage sludge. In contrast, for Brigadier and Hereward, grain Cd concentrations were near to and less than the EU limit, respectively, at soil Cd concentrations of 3 mg kg(-1).     

城市污水厂混合污泥好氧消化处理研究

以城市污水处理厂的初沉污泥与剩余污泥的混合污泥为对象,研究了影响污泥好氧消化处理的各项因素.通过测定氧摄取速率(OUR)和此污泥好氧速率(SOUR),对实验结果进行了探讨.     

Environmental assessment of supercritical water oxidation of sewage sludge

Environmental aspects of using supercritical water oxidation (SCWO) to treat sewage sludge were studied using a life cycle assessment (LCA) methodology. The system studied is the first commercial scale SCWO plant for sewage sludge in the world, treating sludge from the municipal wastewater treatment facility in Harlingen, TX, USA. The environmental impacts were evaluated using three specific environmental attributes: global warming potential (GWP), photo-oxidant creation potential (POCP) and resource depletion; as well as two single point indicators: EPS2000 and EcoIndicator99. The LCA results show that for the described process, gas-fired preheating of the sludge is the major contributor to environmental impacts, and emissions from generating electricity for pumping and for oxygen production are also important. Overall, SCWO processing of undigested sewage sludge is an environmentally attractive technology, particularly when heat is recovered from the process. Energy-conserving measures and recovery of excess oxygen from the SCWO process should be considered for improving the sustainability potential.     

The deep-ocean option for the disposal of sewage sludge

Summary Present methods of disposal of high-bulk low-toxicity wastes, such as sewage sludge, into shallow marine environments are beginning to be questioned by many environmentalists. The alternative options generally considered all have environmental costs. A novel approach of discharging such wastes as slurries into the deep ocean at depths of 4,000 m close to the abyssal sea bed is considered. Such disposal would fulfil all the criteria required by the Oslo Convention before dumping at sea can be permitted, in that it isolates the waste from Man's ambit and offers no threat to present or foreseeable uses of the ocean. It also seems to fulfil the criteria of the World Conservation Strategy, so long as the oxygen levels in the deep waters of the ocean are not reduced excessively. The improvements in the quality of coastal seas would offset the doubling in the economic cost of disposal.Dr Martin V. Angel is the Head of the Biological Oceanography Group at the Institute of Oceanographic Sciences Deacon Laboratory. He serves on the Council of the WWF, UK and is a member of its Conservation Review Group. He is also a member of the IUCN Commission of Ecology, with particular interests in conservation of oceans and Antarctica. His professional expertise is in the ecology of deep-living pelagic organisms in the oceans but he is also an editor of a research journal,Progress in Oceanography and an external examiner for the Open University.     

Water-soluble and solid-state speciation of phosphorus in stabilized sewage sludge

Three chemicals, ferrous sulfate (Fe-sul), calcium oxide (CaO), and aluminum sulfate (alum), were used to stabilize phosphorus (P) in fresh, anaerobically digested sewage sludge (FSS). The chemically stabilized sludge materials and biosolids compost (BSC) were compared with the FSS with respect to water-soluble phosphorus (WSP) content in its inorganic (WSP(i)) and organic (WSP(o)) forms as well as water-soluble organic carbon (DOC). Solid-state P speciation was further probed by X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy-dispersive X-ray elemental spectrometry (EDXS). Water-soluble P was effectively controlled by a wide range of Fe-sul or CaO additions to the sludge (Ca to P ratio = 3.47-17.72, Fe to P ratio = 1.01-16.53), but by only a narrow range (Al to P ratio = 1.04-2.87) of alum addition. The WSP content in the BSC was also depressed, but to a lesser extent. The pH in the treated sludge ranged from 3.0 to 12.5 and served as a key factor to control P chemistry. No correlation was observed between DOC and WSP(o). No crystallized Ca-P minerals were detected in the CaO-stabilized sludge, but brushite crystallization seemed to be obtained by low addition of Fe-sul and alum. Variscite and strengite crystallization was obtained following high addition of Fe-sul or alum, as detected by XRD and SEM-EDXS. Adsorption of P by newly formed Fe-hydroxide seems to play an important role in the Fe-sul-stabilized sludge. We concluded that administration of the tested chemicals at the proper rate can effectively reduce the hazard of P release and leaching from sludge.     

Interparticle diffusion and thermodynamic modeling studies for the removal of heavy metals using mixed adsorbents in industrial effluents

Pollution of water, air, and soil by industrial effluents is a major problem nowadays. A variety of contaminants are too responsible for changing the physicochemical properties of the receiving body. There are practical treatment solutions available to clean up contaminants from various resources. The term “adsorption” refers to one of them. The purpose of the research work is to remove heavy metals from industrial effluent. Mixed adsorbents prepared from activated charcoal and bone charcoals were used to remove the copper and cadmium ions. The experiment carried out in a batch operation and modeling of these data for intraparticle diffusion and thermodynamic calculations were reported in this research work. At optimum operating condition pH 6; metal ion concentration 50 mg/L; dose 5 g/L; agitation 180 rpm and temperature 40°C maximum 99.41% copper ions and 88.12% cadmium ion removal was achieved. Cadmium ions were well fitted in the thermodynamic model compared to copper ions, as demonstrated by the higher correlation coefficient R² (0.9824) value. Intra particle diffusion demonstrated that film diffusion was a rate-limiting step at the start of the reaction, while microporous intraparticle diffusion was the rate-determining phase later on. A Fourier transformation infrared spectroscopy, X-ray diffraction, and scanning electron micrography analysis confirmed the suitability of mixed adsorbents for the removal of cadmium and copper metal ions.