复合型异质结催化剂AgI-BiOI/ZSM-5可见光催化氧化NO

采用液相浸渍沉淀法制备AgI-BiOI/ZSM-5异质结催化剂,通过X-射线衍射(XRD)、紫外-可见光漫反射光谱(DRS)、扫描电镜(SEM)和交流阻抗(EIS)等表征技术对样品进行表征分析,研究AgI-BiOI/ZSM-5催化剂在可见光条件(λ＞ 420 nm)下催化氧化NO的可行性及异质结催化剂的稳定性.研究结果表明,所制备的AgI-BiOI/ZSM-5催化剂在可见光下催化氧化NO的效率达到90％,表现出良好的催化活性,而且AgI-BiOI/ZSM-5在反复使用5次后其催化活性基本保持不变.EIS测试结果表明,AgI-BiOI/ZSM-5异质结的形成有利于光生电子和空穴的分离,从而提高了AgI-BiOI/ZSM-5的催化活性和稳定性.     

Theoretical study of the dechlorination reaction pathways of octachlorodibenzo-p-dioxin

The dechlorination reaction pathways of 1,2,3,4,6,7,8,9-octachlorodibenzo-p-dioxin (OCDD) by the hydrogen atom are investigated by the density-functional theory B3PW91 method. The dechlorination reactions have large exothermicity and small activation energies. The activation energies (approximately 5 kcal/mol) of the sigma-complex formation due to the hydrogen addition are lower than those (approximately 9 kcal/mol) of the direct chlorine abstraction. It is suggested that the sigma-complex plays an important role in the reactions, although it has scarcely been shown in previous studies of the dechlorination of dioxins. The sigma-complex formation is favored at low temperatures and the chlorine abstraction is favored at high temperatures. Furthermore, it is found that the lateral positions have a marginal preference over the longitudinal positions. The dechlorination of OCDD by the hydrogen atom is thus not likely to result in a dominant formation of the laterally substituted toxic congeners.     

The complete dechlorination of DDT by magnesium/palladium bimetallic particles

The complete dechlorination of 1,1-bis(4-chlorophenyl)-2,2,2-trichloroethane (DDT) by a magnesium/palladium bimetallic system has been accomplished. The reaction takes place under ambient temperature and pressure and mild reaction conditions requiring only 0.25 g of magnesium and 0.3% palladium (wt/wt) to drive the dechlorination of 100 microg DDT (50 ppm in 2 ml). The process is both rapid and complete requiring less than 10 min to attain total dechlorination within the detection limit (approximately 10 pg for DDT) of electron capture detection gas chromatography (GC-ECD). The major product formed, as deduced from mass spectrometry (GC-MS) is the hydrocarbon skeleton, 1,1-diphenylethane. This technology may allow for the development of an economic and environmentally benign method of DDT remediation.     

Photocatalytic oxidation of volatile organic compounds using fluorescent visible light

Photocatalytic oxidation (PCO) of volatile organic compounds (VOCs) is a highly attractive alternative technology for purification and deodorization of indoor air. The main objectives of this study were to demonstrate that a common fluorescent visible light (FVL) lamp can be used to effectively remove by PCO low concentrations of VOCs from slightly contaminated air and to provide some fundamental and technical details on the process. The target VOC was n-butanol, which is a standard reference odorant. Its PCO was studied under a long residence time in a 3.7-L cylindrical reactor with commercial titanium dioxide (TiO2) as the reference photocatalyst and using mostly FVL for illumination. For comparison only, a UV (black) light lamp was used. The gas-phase products were detected and quantified online by gas chromatography (GC). The effects of reactor residence time, of inlet concentration, and of the relative light intensity on the efficiency of the process were also evaluated. At a high n-butanol concentration (0.1 vol %), butanal and propanal were identified as the intermediate products of the process; ethanal appeared when the initial concentration was < or = 850 ppm(v). This indicates that PCO leading to CO2 and H2O is relatively slow and proceeds in a stepwise manner. Although the efficiency of the process with an FVL lamp was significantly lower than when using a UV black light, complete PCO of low concentrations was achieved for 100 ppm(v). In a search for a material with photoactivation extended to higher wavelengths or increased photoactivity, several samples of transition metal- or silver ion-doped (2 atomic %) TiO2 as well as SrTi(1-x-)Fe(x)O3 (x = 0.1 and 0.15) perovskites were included in the study. None of these materials was more active than pure TiO2. The results of this study open new horizons in the area of in door air quality (IAQ) control.     

Enhanced reductive dechlorination of DDT in an anaerobic system of dissimilatory iron-reducing bacteria and iron oxide

The transformation of DDT was studied in an anaerobic system of dissimilatory iron-reducing bacteria (Shewanella decolorationis S12) and iron oxide (α-FeOOH). The results showed that S. decolorationis could reduce DDT into DDD, and DDT transformation rate was accelerated by the presence of α-FeOOH. DDD was observed as the primary transformation product, which was demonstrated to be transformed in the abiotic system of Fe²⁺ + α-FeOOH and the system of DIRB + α-FeOOH. The intermediates of DDMS and DBP were detected after 9 months, likely suggesting that reductive dechlorination was the main dechlorination pathway of DDT in the iron-reducing system. The enhanced reductive dechlorination of DDT was mainly due to biogenic Fe(II) sorbed on the surface of α-FeOOH, which can serve as a mediator for the transformation of DDT. This study demonstrated the important role of DIRB and iron oxide on DDT and DDD transformation under anaerobic iron-reducing environments.     

Photocatalytic soot degradation under UV and visible light

Environmental Science and Pollution Research - Particulate matter is one of the most persistent global air pollutants that is causing health problems, climate disturbance and building...     

Simultaneous photocatalytic reduction of Cr(VI) and oxidation of phenol over monoclinic BiVO4 under visible light irradiation

BiVO4 powder with monoclinic structure was prepared and used as a visible-light catalyst simultaneously for the photooxidation of phenol and the photoreduction of Cr(VI). The photocatalytic efficiency was found to be rather low for either single phenol solution or single Cr(VI) solution. However, the photocatalytic reduction of Cr(VI) and photocatalytic oxidation of phenol proceed more rapidly for the coexistence system of phenol and Cr(VI) than for the single process, showing synergetic effect between the oxidation and reduction reactions. For the simultaneous photocatalytic reduction-oxidation process, the first-order kinetic constant of phenol degradation was 0.0314 min-1, being about six times higher than that for the photocatalytic process of single phenol. This result reveals the feasibility of using Cr(VI) as the electron scavenger of mBiVO4-mediated photocatalytic process of phenol degradation, and gives us an enlightenment to employ other semiconductor with a better visible light response but with a more positive band edge to efficiently degrade organic pollutants. This is the first report for simultaneous photocatalytic reduction of Cr(VI) and removal of phenol under visible light irradiation using photocatalyst mBiVO4.     

Carbon/electron source dependence of polychlorinated biphenyl dechlorination pathways for anaerobic granules

The effect of acclimating anaerobic granules from commercial bioreactors with different carbon/electron sources on their ability to reductively dechlorinate a tri-(2,3,4-CB) and heptachlorobiphenyl (2,2',3,3',4,5,6-CB) was studied. The anaerobic granules were first grown in upflow anaerobic sludge blanket (UASB) reactors fed with two different mixtures of carbon/electron sources, i.e., propionate/butyrate/methanol and formate/methanol. Differences in dechlorination patterns for 2,2',3,3',4,5,6-CB were observed in batch experiments inoculated with granules from these two sets of UASB reactors. Variation of the carbon/electron source, during the dechlorination process, had no effect on the dechlorination pathway, but the extents and rates of dechlorination were highest for ethanol and formate and lowest for pyruvate fed batches. Pre-acclimation of different anaerobic sludges to polychlorinated biphenyls (PCBs) shortened the lag period, but did not influence the PCB dechlorination pathway. This is the first time that similar acclimation conditions for several anaerobic microbial communities prior to inoculation were reported to yield similar substrate specificities for the reductive dechlorination of specific PCB congeners. This research demonstrates a successful strategy for the development of biocatalysts to serve as the inoculum of partially decontaminated sites in order to provide microorganisms with specificities complementary to those of naturally occurring dechlorinators.     

Photoassisted bleaching of dyes utilizing TiO2 and visible light

Titanium dioxide was shown to be generally effective as a catalyst for photobleaching many structural classes of organic dyes in aqueous solution, using visible light. However, results from study of 15 dyes indicate that photobleaching rates differ significantly from families of dyes with different functionalities, and are dependent on the light source and crystalline form of TiO2 used. Sorption characteristic on the TiO2 surface and the aqueous solubility of the dyes also play an important role in the photobleaching rate. Kinetic analysis indicates that the dye photobleaching rates can usually be approximated as pseudo-first-order kinetics. In addition to the generally proposed photocatalytic oxidation mechanism for TiO2 reactions, we observed evidence for two kinds of electron transfer mechanisms that are "photosensitized reduction" and "photosensitized oxidation". Natural sunlight was effectively used to photobleach some of the dyes.     

氮掺杂TiO2可见光光催化剂的制备及性能

以尿素和钛酸丁酯为原料,通过溶胶-凝胶法低温下制备了高可见光催化活性的氮掺杂TiO2(NDT)光催化剂,采用XRD、TEM、BET和UV-Vis DRS等测试手段对其进行了表征,并在自制光催化反应器中降解甲基橙评价了样品的光催化活性。结果表明,当氮与钛的摩尔比为0.5∶1时,350℃焙烧的样品(NDT350)具有最佳的可见光光谱吸收和光催化活性,该催化剂为锐钛矿晶相,平均粒径为21 nm,比表面积为89.13 m2/g。可见光辐照下,NDT350降解甲基橙的表观反应速率常数为1.381×10-2min-1,是商业P25催化剂的16.85倍。NDT350优良的可见光催化活性与其大的比表面积和强烈的可见光光谱吸收有关。     

氮掺杂TiO_2可见光光催化剂的制备及性能

以尿素和钛酸丁酯为原料,通过溶胶-凝胶法低温下制备了高可见光催化活性的氮掺杂TiO2（NDT）光催化剂,采用XRD、TEM、BET和UV-Vis DRS等测试手段对其进行了表征,并在自制光催化反应器中降解甲基橙评价了样品的光催化活性。结果表明,当氮与钛的摩尔比为0.5∶1时,350℃焙烧的样品（NDT350）具有最佳的可见光光谱吸收和光催化活性,该催化剂为锐钛矿晶相,平均粒径为21 nm,比表面积为89.13 m2/g。可见光辐照下,NDT350降解甲基橙的表观反应速率常数为1.381×10-2min-1,是商业P25催化剂的16.85倍。NDT350优良的可见光催化活性与其大的比表面积和强烈的可见光光谱吸收有关。     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Enhanced photocatalytic activity of Bi2WO6 with PVP addition for CO2 reduction into ethanol under visible light

Environmental Science and Pollution Research - The conversion of CO2 into new carbon-based products, such as fuels and chemicals, is an attractive and promising means of mitigating global energy...     

Transition metal-modified zinc oxides for UV and visible light photocatalysis

In order to use photocatalysis with solar light, finding more active and especially visible light active photocatalysts is a very important challenge. Also, studies of these photocatalysts should employ a standardized test procedure so that their results can be accurately compared and evaluated with one another. A systematic study of transition metal-modified zinc oxide was conducted to determine whether they are suitable as visible light photocatalysts. The photocatalytic activity of ZnO modified with eight different transition metals (Cu, Co, Fe, Mn, Ni, Ru, Ti, Zr) in three different concentrations (0.01, 0.1, and 1?at.%) was investigated under irradiation with UV as well as with visible light. The employed activity test is the gas-phase degradation of acetaldehyde as described by the ISO standard 22197-2. The results suggest that the UV activity can be improved with almost any modification element and that there exists an optimal modification ratio at about 0.1?at.%. Additionally, Mn- and Ru-modified ZnO display visible light activity. Especially the Ru-modified ZnO is highly active and surpasses the visible light activity of all studied titania standards. These findings suggest that modified zinc oxides may be a viable alternative to titanium dioxide-based catalysts for visible light photocatalysis. Eventually, possible underlying mechanisms are proposed and discussed.     

Pentachlorophenol dechlorination and simultaneous Cr6+ reduction by Pseudomonas putida SKG-1 MTCC (10510): characterization of PCP dechlorination products, bacterial structure, and functional groups

It is the first report in which a novel psychrotrophic Pseudomonas putida SKG-1 strain was evaluated for simultaneous bioremediation of pentachlorophenol and Cr⁶⁺ under various cultural and nutritional conditions. Pentachlorophenol (PCP) dechlorination products, bacterial structure, and functional groups were characterized by gas chromatography and mass spectrometry (GC–MS), scanning electron microscope and energy dispersive X-ray spectroscopy (SEM–EDS), and Fourier-transform infrared (FTIR) techniques. The strain was extremely tolerant to excessively higher individual concentration of PCP (1,400 mg l^?1) and Cr⁶⁺ (4,300 mg l^?1). Increasing concentration of PCP and Cr⁶⁺ exerted inhibitory effect on bacterial growth and toxicants’ removal. The strain exhibited growth, and concomitantly remediated both the pollutants simultaneously over a broad pH (7.0–9.0) and temperature (28–32 °C) range; maximum growth, PCP dechlorination (87.5 %), and Cr⁶⁺ removal (80.0 %) occurred at optimum pH 8.0 and 30 °C (from initial PCP 100 mg l^?1 and Cr⁶⁺ 500 mg l^?1) under shaking (150 rpm) within 72 h incubation. Optimization of agitation (125 rpm) and aeration (0.4 vvm) in bioreactor further enhanced PCP dechlorination by ~10 % and Cr⁶⁺ removal by 2 %. A direct correlation existed between growth and bioremediation of both the toxicants. Among other heavy metals, mercury exerted maximum and cobalt minimum inhibitory effect on PCP dechlorination and Cr⁶⁺ removal. Chromate reductase activity was mainly associated with the supernatant and cytosolic fraction of bacterial cells. GC–MS analysis revealed the formation of tetrachloro-p-hydroquinone, 2,4,6-trichlorophenol, and 2,6-dichlorophenol as PCP dechlorination products. FTIR spectrometry indicated likely involvement of carbonyl and amide groups in Cr³⁺ adsorption, and SEM–EDS showed the presence of chromium on P. putida surface. Thus, our promising isolate can be ecofriendly employed for biotreatment of various industrial wastes contaminated with high PCP and Cr⁶⁺ concentrations.     

Reductive dechlorination and biodegradation of 2,4,6-trichlorophenol using sequential permeable reactive barriers: laboratory studies

The reductive dechlorination and biodegradation of 2,4,6-trichlorophenol (2,4,6-TCP) was investigated in a laboratory-scale sequential barrier system consisting of a chemical and biological reactive barrier. Palladium coated iron (Pd/Fe) was used as a reactive barrier medium for the chemical degradation of 2,4,6-TCP, and a sand column seeded with anaerobic microbes was used as a biobarrier following the chemical reactive barrier in this study. Only phenol was detected in the effluent from the Pd/Fe column reactor, indicating that the complete dechlorination of 2,4,6-TCP was achieved. The residence time of 30.2-21.2h was required for the complete dechlorination of 2,4,6-TCP of 100 mg l(-1) in the column reactor. The surface area-normalized rate constant (k(SA)) is 3.84 (+/-0.48)x10(-5)lm(-2)h(-1). The reaction rate in the column tests was one order of magnitude slower than that in the batch test. In the operation of the biobarrier, about 100 microM of phenol was completely removed with a residence time of 7-8d. Consequently, the dechlorination prior to biodegradation turns out to increase the overall treatability. Moreover, the sequential permeable reactive barriers, consisting of iron barrier and biobarrier, could be recommended for groundwater contaminated with toxic organic compounds such as chlorophenols.     

Palladium-facilitated electrolytic dechlorination of 2-chlorobiphenyl using a granular-graphite electrode

Palladium-assisted electrocatalytic dechlorination of 2-chlorobiphenyl (2-Cl BP) in aqueous solutions was conducted in a membrane-separated electrochemical reactor with granular-graphite packed electrodes. The dechlorination took place at a granular-graphite cathode while Pd was electro-deposited from the K2PdCl6 in the solution and at a Pd-deposited granular-graphite electrode. Using the Pd-deposited graphite cathode in the membrane reactor for a sequence of experiments, each was conducted under a lower current than in the previous one, and the rate of dechlorination became slower in each consecutive experiment. At the end of this sequence, a duplicate experiment showed a loss of activity of the Pd-deposited granular-graphite cathode. In the experiments of dechlorination while Pd was deposited at the granular-graphite electrode, the rate of dechlorination increased with increases of the initial K2PdCl6 concentration and of the applied cathode potential. In each experiment, the dechlorination of 2-Cl BP was relatively fast at the beginning, as demonstrated in an experiment in which 66.4% of 2-Cl BP was dechlorinated within 4h, but the rate of dechlorination decreased over the time. This decrease can be described with two stages of exponential decrease. The values of the rate constant in the first stage varies with the applied potential and the initial K2PdCl6 concentration, but the values of the rate constant in the second stage do not show any dependence on the potential and the K2PdCl6 concentration. The current efficiency of dechlorination was improved by applying part-time current to the electrodes.     

Ag/Ag2SO3 plasmonic catalysts with high activity and stability for CO2 reduction with water vapor under visible light

Environmental Science and Pollution Research - The conversion of CO2 into useful raw materials for fuels and chemicals by solar energy is described using a plasmonic photocatalyst comprised of Ag...     

Photocatalytic degradation of the fungicide Fenhexamid in aqueous TiO(2) suspensions: identification of intermediates products and reaction pathways

Liquid-chromatography interfaced with time-of-flight mass spectrometry (LC-TOF/MS) was used to separate and characterize the transformation products arising from TiO₂-photocatalytic degradation of the fungicide Fenhexamid (FEX) in aqueous solution under simulated solar irradiation. Prior to identification, irradiated solutions of FEX (10 mg L⁻¹) were concentrated by solid-phase extraction. Assignments of the mass spectra ions were aided by elemental composition calculations, comparison of structural analogues and available literature, and acquired knowledge regarding mass spectrometry of related heterocyclic compounds. The primary transformation intermediates identified were hydroxyl and/or keto-derivatives. Several positional isomers are typically produced as a consequence of the non-selectivity of the OH radical attack. Moreover, products resulted from the cleavage of the amide and NHdichlorophenol bonds were formed. Finally, cyclic - benzo[d]oxazole intermediates are also formed through an intramolecular photocyclization process and cleavage of halogen - carbon bond. In the case of the hydroxy and/or keto-derivatives, the generic fragmentation scheme obtained from the interpretation of the ESI-TOF-MS data cannot be diagnostic to precisely localize the position of the entering substituent on the FEX molecule, and thus to characterize all its possible oxygenated derivatives by assigning a plausible structure with confidence. On the basis of identified products different pathways of photocatalytic degradation of FEX were proposed and discussed.