End-of-life flows of multiple cycle consumer products

Explicit expressions for the end-of-life flows (EOL) of single and multiple cycle products (MCPs) are presented, including deterministic and stochastic EOL exit. The expressions are given in terms of the physical parameters (maximum lifetime, T, annual cycling frequency, f, number of cycles, N, and early discard or usage loss). EOL flows are also obtained for hi-tech products, which are rapidly renewed and thus may not attain steady state (e.g. electronic products, passenger cars). A ten-step recursive procedure for obtaining the dynamic EOL flow evolution is proposed. Applications of the EOL expressions and the ten-step procedure are given for electric household appliances, industrial machinery, tyres, vehicles and buildings, both for deterministic and stochastic EOL exit, (normal, Weibull and uniform exit distributions). The effect of the physical parameters and the stochastic characteristics on the EOL flow is investigated in the examples: it is shown that the EOL flow profile is determined primarily by the early discard dynamics; it also depends strongly on longevity and cycling frequency: higher lifetime or early discard/loss imply lower dynamic and steady state EOL flows. The stochastic exit shapes the overall EOL dynamic profile: Under symmetric EOL exit distribution, as the variance of the distribution increases (uniform to normal to deterministic) the initial EOL flow rise becomes steeper but the steady state or maximum EOL flow level is lower. The steepest EOL flow profile, featuring the highest steady state or maximum level, as well, corresponds to skew, earlier shifted EOL exit (e.g. Weibull). Since the EOL flow of returned products consists the sink of the reuse/remanufacturing cycle (sink to recycle) the results may be used in closed loop product lifecycle management operations for scheduling and sizing reverse manufacturing and for planning recycle logistics. Decoupling and quantification of both the full age EOL and of the early discard flows is useful, the latter being the target of enacted legislation aiming at increasing reuse.     

A new rate index for environmental monitoring of combined reuse/recycle packaging systems.

It is shown that the conventional recycling rate fails to reflect environmental performance for packaging flows with both recycle and reuse. The reuse rate, the total number of reuse trips and the reuse- lifetime are also shown to be inadequate. A new rate index defined in terms of the total amount of packaging material reaching the consumer is proposed. It reflects immediate improvements in environmental impact according to specific criteria and it reduces to the conventional rate for systems with only recycle. Albeit this shortcut environmental assessment is not entirely comprehensive and does not unveil a full sustainability profile, it may be useful for immediate packaging flow evaluation and policy implementation. For given packaging production technology it reveals a specific maximum level on recycling, below which environmental impacts from processing are limited or reduced, even if production level grows. Cleaner technologies in reprocessing of recycled materials may elevate this maximum level while still limiting or reducing environmental impacts.     

Waste battery treatment options: Comparing their environmental performance

Waste consumer batteries are recycled using different routes based on hydrometallurgical and pyrometallurgical processes. Two hydrometallurgical and two pyrometallurgical treatment scenarios are compared starting from an average composition of Belgian waste batteries. The environmental performance is compared using life cycle analysis (LCA). The recycling rate is studied through mass balance calculation.Each treatment scenario results in a specific recycling rate. The environmental impact and benefits also vary between the treatment options. There is no such thing as a typical hydrometallurgical or pyrometallurgical treatment. When applying a hydrometallurgical treatment scenario, the focus lies on zinc and iron recycling. When allowing manganese recycling, the energy demand of the hydrometallurgical process increases considerably. Both pyrometallurgical options recycle zinc, iron and manganese. According to the LCA, none of the treatment scenarios performs generally better or worse than the others. Each option has specific advantages and disadvantages. The Batteries Directive 2006/66/EC sets out a recycling rate of 50% for consumer waste batteries. Based on metal recycling alone, the mass balances show that the target is difficult to obtain.     

The life cycle assessment of an e-waste treatment enterprise in China

Electrical and electronic waste (e-waste) has become one of the fastest growing waste streams in the world, and many countries have established e-waste treatment enterprises to solve their e-waste problems. In this study, a life cycle assessment (LCA) was undertaken to quantitatively investigate the environmental impacts of an e-waste treatment enterprise in China. The LCA is constructed by SimaPro software version 7.2 and expressed with the Eco-indicator 99 life cycle impact assessment method. For a sensitivity analysis of the overall LCA results, the so-called CML method is used in order to estimate the influence of the choice of the assessment method on the result. According to the survey data, discarded TV sets accounted for the highest proportion of e-waste treated in the enterprise in 2010. The e-waste treatment had little environmental impact, and at the same time large environmental benefits can be achieved mainly due to the recycled resources and reuse of some components. Based on the research results, it can be seen that recycled metal, especially copper, would be of more importance for environmental benefits. Relevant results and data from this study could provide decision support to enterprise managers and government sectors.     

Life cycle assessment of solid refuse fuel production from MSW in Korea

Solid refuse fuel (SRF) produced from waste materials is a promising fuel that can be utilized for energy recovery in industries. This study considered both characterization and weighting modeling as life cycle assessment (LCA) results. This study aimed to analyze the flows of materials and energy and to evaluate the environmental impact of SRF plants using LCA and compared them with an incineration plant. Based on the results of material and energy flow analysis, SRF products had various energy potentials depending on the treatment method of municipal solid waste (MSW) and replaced the current fossil fuels by SRF combustion. Global impacts were mainly influenced by energy consumption, especially drying methods in the production of SRF, and affected the results of the weighting analysis. The SRF plant with a bio-drying option was evaluated as the best effective practice in the weighting analysis. The LCA results in this study indicated 0.021–9.88 points according to drying methods for SRF production and 1.38 points for incineration. In the sensitivity analysis, the environmental impact of SRF production was found to be significantly affected by the drying methods for MSW and the utilization of fossil energy. Thus, improvement of the drying options could significantly reduce the environmental impact.     

A flexible environmental reuse/recycle policy based on economic strength

Environmental policies based on fixed recycling rates may lead to increased environmental impacts (e.g., landfilled wastes) during economic expansion. A rate policy is proposed, which is adjusted according to the overall strength or weakness of the economy, as reflected by overall packaging demand and consumption, production and imports-exports. During economic expansion featuring rising consumption, production or exports, the proposed flexible policy suggests a higher reuse/recycle rate. During economic slowdown a lower rate results in lower impacts. The flexible target rates are determined in terms of annual data, including consumption, imports-exports and production. Higher environmental gains can be achieved at lower cost if the flexible policy is applied to widely consumed packaging products and materials associated with low rates, or if cleaner recycling technology is adopted.     

Improvement actions in waste management systems at the provincial scale based on a life cycle assessment evaluation

This paper reports some of the findings of the ‘GERLA’ project: GEstione Rifiuti in Lombardia – Analisi del ciclo di vita (Waste management in Lombardia – Life cycle assessment). The project was devoted to support Lombardia Region in the drafting of the new waste management plan by applying a life cycle thinking perspective. The present paper mainly focuses on four Provinces in the Region, which were selected based on their peculiarities. Life cycle assessment (LCA) was adopted as the methodology to assess the current performance of the integrated waste management systems, to discuss strengths and weaknesses of each of them and to design their perspective evolution as of year 2020.Results show that despite a usual business approach that is beneficial to all the provinces, the introduction of technological and management improvements to the system provides in general additional energy and environmental benefits for all four provinces. The same improvements can be easily extended to the whole Region, leading to increased environmental benefits from the waste management sector, in line with the targets set by the European Union for 2020.     

Greenhouse gases emissions from solid waste: an analysis of Expo 2010 Shanghai,China

The management of greenhouse gases (GHGs) emissions is currently a very important environmental issue. Mega-event organizers and host cities have attached great importance to GHGs emissions associated with event-related activities. However, GHGs emissions from event solid waste have never been thoroughly discussed. This study investigated GHGs emissions of major event’s solid waste using life cycle assessment, based on Shanghai Expo case. The results showed that GHGs from collecting and sorting, transportation and landfill treatment amount to 9790 t CO₂e. And the emission intensity is estimated to be 134 g CO₂e per event service. GHGs reduction from recycling amounts to 48 kt CO₂e, with 78 % of these the result of construction waste recycle. It illustrates that waste recycle plays a vital role in GHGs mitigation. Finally, the study suggests that the concept of waste avoidance, waste reuse and waste recycle is an effective waste management to mitigate climate change and should be implemented in major event to achieve the goal of green event.     

Empirical analysis of reward to return: based on case studies of lunch boxes in Japan

To recycle or reuse used containers, it is necessary first to collect them. One way to do this is to give rewards to persons who return used packaging and containers to designated places. Many Japanese university cooperatives use recyclable lunch boxes for take-out food, and they collect used boxes in a variety of ways, including such reward giving. By analyzing the responses of university cooperatives to questionnaires on the ways that they collect used recyclable lunch boxes, this study examines the effect of this reward giving on the collection rate. The study results suggest that cash rewards are more effective in increasing the rate of return of used containers than setting up collection boxes that offer no rewards upon return, or giving point-based rewards.     

The contemporary Oceania zinc cycle: one-year stocks and flows

The material flow approach provides a framework from which to address resource management and estimate gross environmental impacts, both spatially and temporally. In this article, the major flows of zinc in Oceania over its entire life-cycle are examined; these include production (mining, milling, and refining), fabrication and manufacturing of semi- and finished products, use, and the waste management system. Comprehensive mass balances were applied to determine the zinc flows, including the quantities of zinc entering stocks in waste and in-use reservoirs. The Oceania cycle shows that substantial amounts of zinc (about 1120Gg/year) are mined on the continent. The total flow of zinc in finished products entering the use stage is about 8.6kg/(capita.year), substantially exceeding the zinc flow in discarded products. This difference, about 7.2kgZn/(capita.year) on average, is added to the in-use reservoir, largely for galvanizing applications in domestic construction and transportation. Less than 60% of all discarded zinc entering the waste management system is recycled. Much of the remaining discarded zinc is diluted into other waste streams, where recovery and recycling are probably not economically feasible.     

The potential of recycling and reusing municipal solid waste incinerator ash in Taiwan

By 2004, there were 19 municipal solid waste incinerators (MSWI) with a total yearly treatment capacity of 7.72 million tons in service in Taiwan. All 19 incinerators operated daily to generate about 1.05 million tons of incinerator ash, including bottom ash and stabilized fly ash in 2003, and the average ash yield is 18.67%. The total number of incinerators is expected to increase to 27, serving almost all cities in Taiwan by 2007. The authors have suggested a set of criteria based on the yield of incinerator ash (Phi) to study the ash recycle and reuse potential. The Taiwan Environmental Protection Administration has studied the treatment and reuse of MSWI ashes for many years and collected references on international experience accumulated by developed nations for establishing policies on treatment and reuse of MSWI ashes. These citations were analyzed as the basis for current governmental decision making on policies and factors to be considered for establishing policies on recycle and reuse of MSWI ashes. Feasible applications include utilization of ashes, which after sieving and separation of metal particles, produce granular materials. When granular materials comply with TCLP limitations, they can be utilized as cement additives or road base. The procedures of evaluation have been proposed in the performance criteria to be included in the proposed decision-making process of ash utilization.     

ICT reuse in socio-economic enterprises

In Europe, socio-economic enterprises such as charities, voluntary organisations and not-for-profit companies are involved in the repair, refurbishment and reuse of various products. This paper characterises and analyses the operations of socio-economic enterprises that are involved in the reuse of Information and Communication Technology (ICT) equipment. Using findings from a survey, the paper specifically analyses the reuse activities of socio-economic enterprises in the UK from which Europe-wide conclusions are drawn. The amount of ICT products handled by the reuse organisations is quantified and potential barriers and opportunities to their operations are analysed. By-products from reuse activities are discussed and recommendations to improve reuse activities are provided. The most common ICT products dealt with by socio-economic enterprises are computers and related equipment. In the UK in 2010, an estimated 143,750 appliances were reused. However, due to limitations in data, it is difficult to compare this number to the amount of new appliances that entered the UK market or the amount of waste electrical and electronic equipment generated in the same period. Difficulties in marketing products and numerous legislative requirements are the most common barriers to reuse operations. Despite various constraints, it is clear that organisations involved in reuse of ICT could contribute significantly to resource efficiency and a circular economy. It is suggested that clustering of their operations into “reuse parks” would enhance both their profile and their products. Reuse parks would also improve consumer confidence in and subsequently sales of the products. Further, it is advocated that industrial networking opportunities for the exchange of by-products resulting from the organisations’ activities should be investigated. The findings make two significant contributions to the current literature. One, they provide a detailed insight into the reuse operations of socio-economic enterprises. Previously unavailable data has been presented and analysed. Secondly, new evidence about the by-products/materials resulting from socio-economic enterprises’ reuse activities has been obtained. These contributions add substantially to our understanding of the important role of reuse organisations.     

Life cycle assessment of sewage sludge co-incineration in a coal-based power station

A life cycle assessment was conducted to evaluate the environmental and economic effects of sewage sludge co-incineration in a coal-fired power plant. The general approach employed by a coal-fired power plant was also assessed as control. Sewage sludge co-incineration technology causes greater environmental burden than does coal-based energy production technology because of the additional electricity consumption and wastewater treatment required for the pretreatment of sewage sludge, direct emissions from sludge incineration, and incinerated ash disposal processes. However, sewage sludge co-incineration presents higher economic benefits because of electricity subsidies and the income generating potential of sludge. Environmental assessment results indicate that sewage sludge co-incineration is unsuitable for mitigating the increasing pressure brought on by sewage sludge pollution. Reducing the overall environmental effect of sludge co-incineration power stations necessitates increasing net coal consumption efficiency, incinerated ash reuse rate, dedust system efficiency, and sludge water content rate.     

Life cycle assessment of a national policy proposal - the case of a Swedish waste incineration tax

At the core of EU and Swedish waste policy is the so-called waste hierarchy, according to which waste should first be prevented, but should otherwise be treated in the following order of prioritisation: reuse, recycling when environmentally motivated, energy recovery, and last landfilling. Some recent policy decisions in Sweden aim to influence waste management in the direction of the waste hierarchy. In 2001 a governmental commission assessed the economic and environmental impacts of introducing a weight-based tax on waste incineration, the purpose of which would be to encourage waste reduction and increase materials recycling and biological treatment. This paper presents the results of a life cycle assessment (LCA) of the waste incineration tax proposal. It was done in the context of a larger research project concerning the development and testing of a framework for Strategic Environmental Assessment (SEA). The aim of this paper is to assess the life cycle environmental impacts of the waste incineration tax proposal, and to investigate whether there are any possibilities of more optimal design of such a tax. The proposed design of the waste incineration tax results in increased recycling, but only in small environmental improvements. A more elaborate tax design is suggested, in which the tax level would partly be related to the fossil carbon content of the waste.     

Multi-objective reverse logistics model for integrated computer waste management.

This study aimed to address the issues involved in the planning and design of a computer waste management system in an integrated manner. A decision-support tool is presented for selecting an optimum configuration of computer waste management facilities (segregation, storage, treatment/processing, reuse/recycle and disposal) and allocation of waste to these facilities. The model is based on an integer linear programming method with the objectives of minimizing environmental risk as well as cost. The issue of uncertainty in the estimated waste quantities from multiple sources is addressed using the Monte Carlo simulation technique. An illustrated example of computer waste management in Delhi, India is presented to demonstrate the usefulness of the proposed model and to study tradeoffs between cost and risk. The results of the example problem show that it is possible to reduce the environmental risk significantly by a marginal increase in the available cost. The proposed model can serve as a powerful tool to address the environmental problems associated with exponentially growing quantities of computer waste which are presently being managed using rudimentary methods of reuse, recovery and disposal by various small-scale vendors.     

A management system for end-of-life tyres: a Portuguese case study

The European Union introduced several policy instruments based in the extended producer responsibility (EPR) in order to improve the environmental performance of products and services through their life cycles. In this context, the Portuguese government decided to apply the EPR concept to tyres, and producers were obliged to constitute an end-of-life management system to promote the collection, recycling and reuse of end-of-life (EOL) tyres. This required producers, distributors, recyclers and retreaders to be identified and characterized, and local processing infrastructures to be analyzed. The information was used to design an economically optimised EOL tyre management system while promoting the activity of all EOL operators in order for the imposed collecting and recovery targets to be fulfilled. This paper discusses the interaction between the different governmental, private and academic institutions for the creation of the integrated management system for EOL tyres, the approach taken, the technical, political and legal aspects underneath them, as well as the environmental consequences induced by the creation of the management system. The results obtained during the first years of operation are reported and show an increase in the collection and recycling of EOL tyres and the consolidation of the collection and processing infrastructures.     

Life cycle assessment of bagasse waste management options

Bagasse is mostly utilized for steam and power production for domestic sugar mills. There have been a number of alternatives that could well be applied to manage bagasse, such as pulp production, conversion to biogas and electricity production. The selection of proper alternatives depends significantly on the appropriateness of the technology both from the technical and the environmental points of view. This work proposes a simple model based on the application of life cycle assessment (LCA) to evaluate the environmental impacts of various alternatives for dealing with bagasse waste. The environmental aspects of concern included global warming potential, acidification potential, eutrophication potential and photochemical oxidant creation. Four waste management scenarios for bagasse were evaluated: landfilling with utilization of landfill gas, anaerobic digestion with biogas production, incineration for power generation, and pulp production. In landfills, environmental impacts depended significantly on the biogas collection efficiency, whereas incineration of bagasse to electricity in the power plant showed better environmental performance than that of conventional low biogas collection efficiency landfills. Anaerobic digestion of bagasse in a control biogas reactor was superior to the other two energy generation options in all environmental aspects. Although the use of bagasse in pulp mills created relatively high environmental burdens, the results from the LCA revealed that other stages of the life cycle produced relatively small impacts and that this option might be the most environmentally benign alternative.     

Life‐cycle assessment of in situ thermal remediation

A detailed cradle‐to‐grave life‐cycle assessment (LCA) of an in situ thermal treatment remedy for a chlorinated‐solvent‐contaminated site was performed using process LCA. The major materials and activities necessary to install, operate, monitor, and deconstruct the remedy were included in the analysis. The analysis was based on an actual site remedy design and implementation to determine the potential environmental impacts, pinpoint major contributors to impacts, and identify opportunities for improvements during future implementation. The Electro‐Thermal Dynamic Stripping Process (ET‐DSP?) in situ thermal technology coupled with a dual‐phase extraction and treatment system was evaluated for the remediation of 4,400 yd³ of tetrachloroethene‐ and trichloroethene‐impacted soil, groundwater, and bedrock. The analysis was based on an actual site with an estimated source mass of 2,200 lbs of chlorinated solvents. The remedy was separated into four stages: remedy installation, remedy operation, monitoring, and remedy deconstruction. Environmental impacts were assessed using Sima Pro software, the ecoinvent database, and the ReCiPe midpoint and endpoint methods. The operation stage of the remedy dominated the environmental impacts across all categories due to the large amount of electricity required by the thermal treatment technology. Alternate sources of electricity could significantly reduce the environmental impacts of the remedy across all impact categories. Other large impacts were observed in the installation stage resulting from the large amount of diesel fuel, steel, activated carbon, and asphalt materials required to implement the technology. These impacts suggest where opportunities for footprint reductions can be found through best management practices such as increased materials reuse, increased recycled‐content materials use, and clean fuels and emission control technologies. Smaller impacts were observed in the monitoring and deconstruction stages. Normalized results show the largest environmental burdens to fossil depletion, human toxicity, particulate matter formation, and climate‐change categories resulting from activities associated with mining of fossil fuels for use in electricity production. In situ thermal treatment can reliably remediate contaminated source areas with contaminants located in low‐permeability zones, providing complete destruction of contaminants in a short amount of time, quick return of the site to productive use, and minimized quantities of hazardous materials stored in landfills for future generations to remediate. However, this remediation strategy can also result in significant emissions over a short period of time. It is difficult to quantify the overall value of short‐term cleanups with intense treatment emissions against longer‐term cleanups with lower treatment emissions because of the environmental, social, and economic trade‐offs that need to be considered and understood. LCA is a robust, quantitative tool to help inform stakeholder discussions related to the remedy selection process, trade‐off considerations, and environmental footprint‐reduction opportunities, and to complement a broader toolbox for the evaluation of sustainable remediation strategies. © 2012 Wiley Periodicals, Inc.     

Integrating Remediation and Reuse to Achieve Whole‐System Sustainability Benefits

This perspective article was prepared by members of the Sustainable Remediation Forum (SURF), a professional nonprofit organization seeking to advance the state of sustainable remediation within the broader context of sustainable site reuse. SURF recognizes that remediation and site reuse, including redevelopment activities, are intrinsically linked—even when remediation is subordinate to or sometimes a precursor of reuse. Although the end of the remediation life cycle has traditionally served as the beginning of the site's next life cycle, a disconnect between these two processes remains. SURF recommends a holistic approach that brings together remediation and reuse on a collaborative parallel path and seeks to achieve whole‐system sustainability benefits. This article explores the value of integrating remediation into the reuse process to fully exploit synergies and minimize the costs and environmental impacts associated with bringing land back into beneficial use. © 2013 Wiley Periodicals, Inc.