微米级负载型TiO_2催化剂在光催化-膜分离反应器中的应用

基于光催化-膜分离三相流化床反应器的结构特点及膜分离特性,以微米级MCM-41分子筛为载体,采用原位生成法制备微米级负载型TiO2催化剂。针对微米级负载型TiO2催化剂在光催化-膜分离反应器中的分布特性、悬浮特性、分离特性及膜污染特性进行研究。结果表明,曝气量一定的情况下,微米级负载型TiO2催化剂在光催化-膜分离反应器中具有良好的悬浮特性,且优于纳米TiO2。随着催化剂投加量的增加,悬浮浓度也随之增加。光催化反应器底部曝气0.3m3/h、催化剂投加量为1 g/L时为宜。膜分离器中催化剂悬浮浓度明显低于光催化反应器;该微米级催化剂与纳米TiO2相比具有不粘附、不堵塞膜孔等优良特性,能够有效降低膜污染,延长分离膜使用寿命。膜底曝气为0.1 m3/h时,反应器连续运行5 h(未加反冲洗)后,微米级负载型TiO2催化剂和纳米TiO2对膜组件的污染程度分别为膜通量衰减率4.3%和37.4%。反应器连续运行72 h,膜组件依然具有很好的分离特性。     

微米级负载型 TiO2催化剂在光催化-膜分离反应器中的应用简

基于光催化-膜分离三相流化床反应器的结构特点及膜分离特性,以微米级MCM-41分子筛为载体,采用原位生成法制备微米级负载型TiO₂催化剂。针对微米级负载型TiO₂催化剂在光催化-膜分离反应器中的分布特性、悬浮特性、分离特性及膜污染特性进行研究。结果表明,曝气量一定的情况下,微米级负载型TiO₂催化剂在光催化-膜分离反应器中具有良好的悬浮特性,且优于纳米TiO₂。随着催化剂投加量的增加,悬浮浓度也随之增加。光催化反应器底部曝气0.3 m³/h、催化剂投加量为1 g/L时为宜。膜分离器中催化剂悬浮浓度明显低于光催化反应器;该微米级催化剂与纳米TiO₂相比具有不粘附、不堵塞膜孔等优良特性,能够有效降低膜污染,延长分离膜使用寿命。膜底曝气为0.1 m³/h时,反应器连续运行5 h（未加反冲洗）后,微米级负载型TiO₂催化剂和纳米TiO₂对膜组件的污染程度分别为膜通量衰减率4.3%和37.4%。反应器连续运行72 h,膜组件依然具有很好的分离特性。     

一体式光催化－膜分离三相流化床反应器膜污染特性

通过利用颗粒状 TiO2催化剂(平均粒径0.258/μm)对酸性红 B 模拟废水的催化降解实验,对一体式光催化氧化-膜分离三相流化床反应器的膜污染特性进行了研究.结果表明,TiO2是造成膜污染的主要污染物,且 TiO2浓度愈大,膜污染愈严重;本实验体系TiO2的适宜浓度为 2g/L.反应区曝气量在 3.6m3/h 时膜污染最小;膜组件底部曝气装置可大大减轻膜污染,且其曝气量以 0.6 m3/h 为宜.表面冲洗、气体反冲洗和碱洗均可有效地清除膜表面和膜孔内的污染物,使膜通量恢复至90%以上;"表面冲洗 碱洗"和"表面冲洗 碱洗 气体反冲"可进一步提高膜通量的恢复,但不十分明显.     

一体式光催化氧化-膜分离流化床反应器性能的研究

通过对光催化氧化和有机膜分离技术的耦合,设计了一种新型一体式光催化氧化-膜分离流化床反应器,并通过利用颗粒状TiO2催化剂(粒径0.28～0.33 μm)对浓度为10 mg/L的酸性红B模拟废水的降解实验,研究了反应器的性能.结果表明,反应器中TiO2的加入量以2 g/L为宜,废水脱色率达98%;膜组件底部的曝气装置可大大减轻膜污染,"表面冲洗 反冲洗"的清洗方法能够有效地恢复膜通量.     

TiO2光催化-微滤膜分离深度净化亚甲基蓝印染废水

采用悬浮式TiO2光催化膜反应器深度净化纺织工业园区含亚甲基蓝印染废水经生物处理二级出水,利用中空纤维微滤膜进行催化剂截留分离,研究催化剂投加量、运行时间、溶解氧、搅拌方式对出水水质及膜通量的影响。结果表明:光催化会消耗体系溶解氧,鼓风曝气搅拌可同时为系统供氧,优于机械搅拌;该耦合体系的催化剂最佳投加量为1 g/L,经光催化氧化-膜组合工艺处理后水质优于GB 4287-1992《纺织染整工业污染物排放标准》的I级标准,符合建设部颁布的《生活杂用水水质标准》(CJ/T 48-1999)。     

光催化-膜分离三相流化床循环反应装置处理酸性红B废水

耦合光催化氧化和有机膜分离技术,设计了一种新型光催化氧化-有机膜分离三相流化床循环反应装置（循环反应装置）;并对循环反应装置光催化降解酸性红B时的影响因素进行了研究。结果表明,减小膜出水通量和降低酸性红B废水浓度均有利于膜出水降解率的提高;循环反应装置中废水降解率随光催化反应器底部曝气量的增加而先增加再降低,膜分离器中废水降解率的波动则随曝气量的增加而总是在增大,其最佳曝气量为1．00m^3／h;光催化反应器中多光源布置有利于循环反应装置的稳定运行;循环反应装置可有效地处理酸性红B废水。     

超细TiO2粒子的超滤分离及回用特性

针对TiO2超细粒子的超滤分离特性进行了试验研究,探讨了操作压力、膜面流速、TiO2投量、pH、电解质等参数条件对膜通量的影响规律及作用机理,证实了浓差极化及滤饼层阻力是影响通量变化的主导因素,在此基础上确定了适宜的超滤工艺条件及膜清洗方式.以甲基橙为降解基质分别测试了经混凝与超滤分离后的TiO2光催化活性,结果表明,超滤不仅可实现TiO2粒子与水的彻底分离,且分离后TiO2催化活性与初次使用相当.研究表明超滤用于悬浮光催化体系的固液分离及催化剂再用是可行的.     

超细TiO2粒子的超滤分离及回用特性

针对TiO2超细粒子的超滤分离特性进行了试验研究，探讨了操作压力、膜面流速、TiO2投量、pH、电解质等参数条件对膜通量的影响规律及作用机理，证实了浓差极化及滤饼层阻力是影响通量变化的主导因素，在此基础上确定了适宜的超滤工艺条件及膜清洗方式。以甲基橙为降解基质分别测试了经混凝与超滤分离后的TiO2光催化活性，结果表明，超滤不仅可实现TiO2粒子与水的彻底分离，且分离后TiO2催化活性与初次使用相当。研究表明超滤用于悬浮光催化体系的固液分离及催化剂再用是可行的。     

膨胀珍珠岩负载TiO2光催化脱色性能的研究

以钛酸四丁酯为原料，膨胀珍珠岩为载体，用溶胶—凝胶法制备可漂浮于水面的负载型TiO2。利用该负载型TiO2对罗丹明B(RB)进行光催化脱色实验，结果表明，浸渍3次的负载型TiO2光催化活性最高，催化剂最佳用量为500mg／100mL RB，经5h光照，对100mL浓度为1mg／L和2．5mg／LRB脱色率分别为76．67％和47．27％；该催化剂使用寿命长，25h后催化剂脱色性能没有减弱，可重复使用；经8h光照，染料废水脱色效果好。     

光催化处理二甲苯废气的影响因素研究

使用自制光催化反应器,以多孔型载体分别负载纳米TiO2和普通TiO2,以256～265 nm紫外光为光源,探讨了TiO2光催化处理二甲苯废气的影响因素及处理性能.结果发现,在以纳米型TiO2作为催化剂、在紫外光强为1000 W且布光均匀、风量为1000 m3/h、进口浓度350 mg/m3、通入臭氧的工况条件下运行,整个系统对二甲苯的去除率平均在90%以上.     

好氧颗粒污泥动态膜生物反应器工艺参数及运行性能

以一体式尼龙筛网动态膜生物反应器(DMBR)为研究体系,与好氧颗粒污泥相结合,形成新的好氧颗粒污泥动态膜生物反应器(AGDMBR),探讨了在新工艺条件下对COD、氨氮的去除,以及出水浊度的变化,与活性污泥动态膜生物反应器(DMBR)做比较,研究了进水流量、曝气量等工艺运行参数与膜污染之间的关系,并对系统中污泥的EPS进行分析。结论表明,AGDMBR系统对COD和NH4+-N的平均去除率分别为91%和95%,出水浊度为6 NTU,处理效果均优于DMBR系统;AGDMBR系统在运行过程中膜污染速度随进水流量的增大而加快;曝气量为125～150 L/h时,膜通量持续时间最长;AGDMBR系统比DMBR系统在膜污染的延缓上具有明显的优势。     

Effect of CO on NO oxidation over platinum based catalysts for hybrid fast SCR process

The oxidation characteristics of NO over Pt/TiO2 (anatase, rutile) catalysts have been determined in a fixed bed reactor as a function of O2, CO and SO2 concentrations in the presence of 8% water. The conversion of NO to NO2 increases with increasing O2 concentration up to 12% and it levels off. This saturation effect is more pronounced over rutile-Pt/TiO2 (r-Pt/TiO2) than that of anatase-Pt/TiO2 (a-Pt/TiO2). The presence of CO increases NO oxidation significantly and this enhanced effect is more pronounced on a-Pt/TiO2 than that on r-Pt/TiO2 with increasing CO concentration at lower temperatures. The same effect is also observed on the catalysts with different Pt and tungsten oxide (WO3) loadings. With increasing Pt and WO3 loadings on TiO2 support (Pt-WO3/TiO2), formation of NO2 is high even at lower temperatures. The presence of SO2 significantly suppresses the oxidation of NO over both r-Pt/TiO2 and a-Pt/TiO2 catalysts but it is less pronounced due to low stability of sulfate on a-Pt/TiO2.     

The effects of manganese precursors on Mn-based/TiO2 catalysts for catalytic reduction of NO with NH3

Manganese acetate (MnAc) and manganese nitrate (MnN) were employed as precursors for the preparation of MnAc)/TiO2, Mn (N)/TiO2, Mn(Ac)-Ce/TiO2, and Mn(N)-Ce/TiO2 by impregnation. These complexes were used as catalysts in the low-temperature selective catalytic reduction of NO with NH3. The influence of manganese precursors on catalyst characteristics, the reduction activity, and the stability of the catalysts to poisoning by H2O and SO2 were studied. Experiments showed that Mn(N) produced MnO2 with large grain sizes in Mn(N)/TiO2 catalyst. On the contrary, Mn(Ac) led to highly dispersed and amorphous Mn2O3 in Mn (Ac)/TiO2 catalyst, which had better catalytic activity and stability to SO2 at low temperatures. The doping of cerium reduced the differences in catalytic performance between the catalysts derived from different Mn precursors.     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

纳米生态建筑涂料光催化降解甲醛的研究

以掺加纳米TiO2制备的光催化建筑涂料为催化剂,研究了在紫外光照条件下对气态甲醛的催化降解,并探讨了纳米催化剂晶型、用量和吸附量对光催化降解甲醛的影响。实验结果表明,锐钛型纳米TiO2具有较高的光催化降解甲醛的活性,1h甲醛的降解率可达到70％左右,产物主要为二氧化碳和水;光催化降解甲醛受到涂膜上吸附量的较大影响;该涂料对甲醛的光催化降解反应表现出一级动力学速率规律,且具有良好的线性关系。     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下,超滤（UF）已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法,将聚偏氟乙烯（PVDF）、聚乙二醇（PEG）和二氧化钛（TiO2）共混制得光催化复合分离膜并对其进行扫描电子显微镜（SEM）、原子力显微镜（AFM）和X射线能谱仪（EDS）等相应的表征。比较了有无光照条件下,PVDF-PEG和PVDF—PEG—TiO2膜对腐殖酸（HA）的截留和超滤过程中的膜污染情况。研究结果表明,TiO2光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强,PVDF-PEG—TiO2膜的抗污染性能越好。另外,光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

The separation of catalyst after photocatalytic reactions conducted in the presence of TiO2/FeCl3/UV

One of the problems connected with wastewater treatment by the photocatalytic method in the presence of TiO2 suspension is necessity of the later catalyst separation. The method proposed by us for this purpose, consists in the usage of coagulation of TiO2 suspension with the aid of FeCl3, particularly in the cases when addition of the salt is used in order to intensification of the photocatalytic process. The effects of the TiO2 separation were studied from the mixtures, after photocatalytic Acid Orange 7 degradation, with dosage of FeCl3 at different stages of the process. The coagulation was carried out at different pH values as well as different FeCl3 concentrations. It was stated that nearly 100% of separation and simultaneously, nearly 100% of decolouration of the examined Acid Orange 7 solutions after their illumination in the presence of TiO2/FeCl3 and coagulation which was produced only by increasing of pH of the obtained mixtures, were nearly possible.     

How to optimize hollow-fiber submerged membrane bioreactors

Membrane fouling is linked to reversible or irreversible accumulation of macromolecules and solids on membrane surfaces and to the irreversible adsorption inside pores. If reversible accumulation can be controlled by filtering in subcritical conditions, then adsorption could also be minimized by reducing the soluble organic matter [extracellular polymeric substances, soluble microbial products (SMP)]. This research shows how the choice of operating parameters related to biological reaction (solid retention time and the organic loading rate) can influence the process rate and the by-product (SMP) production. It also illustrates how suspension characteristics and membrane aeration can influence membrane fouling control according to the hollow fiber configuration and to the different scales of observation. The investigations were based on the definition of different fouling level and fine-tuning of a model to better understand the effects of operating parameters on membrane bioreactor filtration.