Light-induced degradation of perfluorocarboxylic acids in the presence of titanium dioxide

The UV-photon-induced degradation of heptafluorobutanoic acid was investigated in acidic aqueous solutions in the presence of titanium dioxide. Heptafluorobutanoic acid could be degraded with this photocatalyst in a light-induced reaction generating carbon dioxide and fluoride anions. Carbon dioxide evolution in a significant amount occurred only in the presence of molecular oxygen and the photocatalyst. The light-induced degradation of trifluoroacetic acid, pentafluoropropanoic acid, nonafluorobutanoic acid, pentadecafluorooctanoic acid, nonafluorobutanesulfonic acid, and heptadecafluorooctanesulfonic acid in the presence of titanium dioxide was also studied. The perfluorocarboxylic acids under investigation are degraded to generate CO(2) and fluoride anions while both perfluorinated sulfonic acids are persistent under the experimental conditions employed in this study. For all compounds photonic efficiencies of the mineralization reaction were estimated to be smaller than 1x10(-5). To increase the photocatalytic activity mixed systems containing homogeneous phosphotungstic acid and heterogeneous titanium dioxide catalysts were also investigated. In the mixtures of these two photocatalysts, the formation rate of CO(2) increased with illumination time.     

二氧化钛/碳纳米管/壳聚糖薄膜的制备及对苯的降解性能

研究了光催化降解挥发性有机化合物过程中催化剂二氧化钛/碳纳米管/壳聚糖薄膜的制备以及该催化剂对苯的光催化性能。首先采用溶胶-凝胶法制备纳米复合材料二氧化钛/碳纳米管,然后利用壳聚糖作为交联剂,制得二氧化钛/碳纳米管/壳聚糖复合材料催化薄膜。通过傅立叶红外光谱(FT-IR)、X射线衍射(XRD)透射电镜扫描(TEM)和紫外-可见光漫反射(UV-Vis)等技术分析了复合材料薄膜的组成、结构、形貌和对光的吸收性能,然后使用该催化剂对室内常见的污染物苯进行降解,并在同样的实验条件下,使用催化剂二氧化钛(P25)/壳聚糖对苯进行降解,对两者催化性能进行对比,结果表明,二氧化钛/碳纳米管/壳聚糖对苯有更强的吸附能力和更高的催化活性。     

日光下黄砂负载TiO2降解邻氯苯酚水溶液

研究了以黄砂为载体,ＴｉＯ２为催化剂,以太阳光为光源对邻氯苯酚水溶液进行光催化降解的可行性。结果表明,锐钛型ＴｉＯ２邓邻氯苯酚有显著的光催化降解作用;ＴｉＯ２的催化活性在焙烧温度３００℃时最高。     

Semiconductor-mediated photocatalysed degradation of two selected priority organic pollutants,benzidine and 1,2-diphenylhydrazine,in aqueous suspension

The photocatalysed degradation of two selected priority organic pollutants, namely benzidine (1) and 1,2-diphenylhydrazine (DPH, 2) has been investigated in aqueous suspensions of titanium dioxide (TiO2) under a variety of conditions employing a pH-stat technique. The degradation was studied by monitoring the change in substrate concentration of the model compound employing HPLC analysis and the decrease in total organic carbon content, respectively, as a function of irradiation time. The degradation kinetics were studied under different conditions such as reaction pH, substrate and photocatalyst concentration, type of TiO2 photocatalyst and the presence of alternative additives such as H2O2, KBrO3 and (NH4)2S2O8 besides molecular oxygen. The degradation rates and the photonic efficiencies were found to be strongly influenced by the above parameters. Toxicity tests for the irradiated samples of benzidine measuring the luminescence of bacteria Vibrio fischeri after 30 min of incubation were also performed. 4-amino-biphenyl (7) and hydroquinone (13) were identified as intermediate products by GC/MS technique and probable pathways for the formation of the products are proposed.     

喷射环流三相光催化反应器可见光下降解酸性湖兰A的研究

设计了一种喷射环流三相光催化反应器。用该反应器在可见光下,对染料酸性湖兰A在不同初始浓度、催化剂浓度、pH、光照时间下光催化降解脱色率的影响进行了研究。实验结果表明,反应最佳pH为6,反应最佳时间为20min,催化剂最佳投加量为8g／L。在最优条件下,染料脱色率达90％以上。     

Degradation of azo dye Procion Red MX-5B by photocatalytic oxidation

The photocatalytic oxidation (PCO) of a monoazo dye Procion Red MX-5B under various physico-chemical conditions was investigated. Degradation of the dye by PCO was enhanced by augmentation in UV intensity, titanium dioxide and hydrogen peroxide concentrations but was inhibited by increase in initial dye concentration. The PCO process was affected by pH in a peculiar way. In the presence of 100 mg/l of TiO2 and the absence of H2O2, the highest reaction rate was observed when the initial pH was 10. With 500 mg/l of TiO2 and 10 mM of H2O2, the reaction was the fastest at initial pH of 3-5. The optimal conditions for the degradation of the dye, at an UV intensity of 17 mW/cm2, were determined to be: TiO2 concentration, 500 mg/l; initial H2O2 concentration, 10 mM; initial pH, 5.0. Monitoring of TOC loss showed that the dye was mineralized by 90% within 80 min under these conditions. Nevertheless, the persistence of a low level of TOC indicated that mineralization was not complete and dead-end product(s) which was (were) resistant to PCO might have accumulated.     

Direct and indirect photolysis of two quinolinecarboxylic herbicides in aqueous systems

The photodegradation of two quinolinecarboxylic herbicides, 7-chloro-3-methylquinoline-8-carboxylic acid (QMe) and 3,7-dichloroquinoline-8-carboxylic acid (QCl), was studied in aqueous solution at different irradiation wavelengths. The effect of sunlight irradiation was investigated also in the presence of titanium dioxide (TiO₂). UV irradiation degraded rapidly QMe affording 7-chloro-3-methylquinoline (MeQ) through a decarboxylation reaction. The reaction rate was lower in the presence of dissolved organic carbon (DOC) because of the adsorption of the herbicide on the organic components. Instead, QCl was stable under both UV light and sunlight irradiation. The irradiation of QMe or QCl solutions with simulated sunlight in the presence of TiO₂ produced the complete mineralization of the two herbicides.     

TiO2光催化氧化降解乳酸的工艺及机理研究

以TiO2为催化剂、紫外灯为光源对乳酸进行光催化降解实验,考察了乳酸初始浓度、TiO2用量、反应时间、曝气方式等因素对乳酸降解率的影响,并在此基础上应用正交实验对降解条件进行优化,同时对乳酸的降解机理进行了探索研究。实验结果表明：以300 W紫外汞灯为光源,在乳酸初始浓度为0.5 g/L、TiO2量为0.20 g/L、反应时间120 min、持续通入空气鼓泡的条件下,乳酸降解效果最佳,乳酸降解率为99.9%;降解12 h总有机碳去除率达91.2%。乳酸光催化降解的反应途径为：乳酸脱羧生成乙醇,乙醇被氧化生成乙醛,进而氧化为乙酸,所有的中间产物被继续降解,最终矿化为CO2和H2O等小分子物质。     

超细TiO2粒子的超滤分离及回用特性

针对TiO2超细粒子的超滤分离特性进行了试验研究,探讨了操作压力、膜面流速、TiO2投量、pH、电解质等参数条件对膜通量的影响规律及作用机理,证实了浓差极化及滤饼层阻力是影响通量变化的主导因素,在此基础上确定了适宜的超滤工艺条件及膜清洗方式.以甲基橙为降解基质分别测试了经混凝与超滤分离后的TiO2光催化活性,结果表明,超滤不仅可实现TiO2粒子与水的彻底分离,且分离后TiO2催化活性与初次使用相当.研究表明超滤用于悬浮光催化体系的固液分离及催化剂再用是可行的.     

Photocatalytic reduction of carbon dioxide to methanol and formic acid by graphene-TiO2

Graphene-TiO₂ was obtained by reduction of graphite oxide by the hydrothermal method. Using photocatalytic activity to reduce carbon dioxide to methanol and formic acid was investigated in this study. The results show that the graphene loading affects the absorption of light in the visible light region. A larger surface area can also improve the catalytic activity. The largest yield of methanol and formic acid, under light of 365 nm, can reach 160 and 150 μmol g^?1, respectively, with 8.5% graphene loading. An increase in graphene loading can enhance photocatalytic performance, but too much will also decrease the reduction efficiency by shielding the light from reaching the catalytic surface. The effect of pH was also investigated. The mechanism of the reaction was also discussed in this study.

Implications: Graphene-TiO₂ hybrids were prepared by the hydrothermal method. Surface area and visible light adsorption increased with the graphene loading. Increased graphene loading improved the methanol and formic acid production. Too much graphene loading will decrease the reduction efficiency. The effect of pH shows that the HCO₃^? species prefers the formation of formic acid. The mechanism of the reaction was also discussed in this study.     

Photocatalytic degradation of amoxicillin from aqueous solutions by titanium dioxide nanoparticles loaded on graphene oxide

Environmental Science and Pollution Research - The photocatalytic degradation of amoxicillin (AMX) by titanium dioxide nanoparticles loaded on graphene oxide (GO/TiO2) was evaluated under UV light....     

Preparation,characterization, and photocatalytic activity evaluation of Fe–N-codoped TiO2/fly ash cenospheres floating photocatalyst

Nitrogen-doped titanium dioxide (TiO₂) and Fe–N-codoped TiO₂ layers on fly ash cenospheres (FAC) as floating photocatalyst were successfully prepared through sol–gel method. Photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), ultraviolet (UV)–Vis diffuse reflectance spectroscopy (DRS), and nitrogen adsorption analyses for Brunauer–Emmett–Teller (BET) specific surface area. Photocatalytic efficiency of the prepared catalyst was evaluated through using the decomposition of Rhodamine B (RhB) as a model compound under visible light irradiation. Photocatalytic activity and kinetics of catalyst under visible light were detected in details from different Fe/Ti mole ratios by detecting photodegradation of RhB. Experimental results show that when the calcination temperature was 550 °C, the dosage of FAC was 3.0 g, and the mole ratio of Fe/Ti was 0.71 %; the synthesized Fe–N-TiO₂/FAC photocatalyst presented as anatase phase and that N and Fe ions were doped into TiO₂ lattice. The material’s specific surface area was 34.027 m²/g, and UV–Vis diffuse reflectance spectroscopy shows that the edge of the photon absorption has been red shifted up to 400–500 nm. Fe–N-codoped titanium dioxide on FAC had excellent photocatalytic activity during the process of photodegradation of RhB under visible light irradiation.

     

Photodegradation of Diquat and Paraquat in aqueous solutions by titanium dioxide: evolution of degradation reactions and characterisation of intermediates

The titanium dioxide assisted photodegradation of Diquat and Paraquat herbicides solutions has been the subject of the present investigation, considering its direct application in the treatment of contaminated waters and soils. To have a better understanding of the photodegradation process, different types of TiO2, commercial and 'home prepared' Ti(1-x)FexO2 (x = 0% and 4%), were used as catalysts, using an UV light as radiation source. The degradation reactions were followed by UV spectroscopy and the intermediates and reaction products were characterised by electrospray ionisation mass spectrometry (ESIMS) combined with collision-induced dissociation (CID) and tandem mass spectrometry (MS/MS). The present study shows that, for photocatalytic degradation of Diquat and Paraquat solutions, a basic pH can be determinant, as well as the type of catalyst. The type of catalyst can also strongly influence the degradation pattern of the herbicide. Regarding complete degradation, we were able to show that Diquat is more persistent than Paraquat. During the photocatalytic processes, several intermediate and reaction products are sequentially formed, to which structures are proposed.     

光助非均相Fenton体系用于活性艳红X-3B脱色的研究

在光助非均相Fenton体系中,采用一种稀土铈铁复合(CeFe)材料作为催化剂,并探讨了该反应体系在不同条件下活性艳红X3B的脱色效果。结果表明:该光助非均相Fenton反应在前10min符合一级反应动力学。采用掺杂0.08mol/L铈制备的CeFe材料对活性艳红X3B具有最佳的脱色效果,在pH3.0、H2O234mg/L、UV253.7nm条件下,10min内该反应体系速率常数k达到0.2456min-1,明显高于相同条件下的UV/H2O2(0.0446min-1)、UV/CeFe(0.0306min-1)体系的速率常数。     

镍网负载纳米TiO2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明：UV灯＋镍网＋TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。     

镍网负载纳米TiO_2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明:UV灯+镍网+TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。     

TiO2/EP光催化降解水体中微污染磺胺嘧啶的研究

制备了膨胀珍珠岩（EP）为载体的TiO2催化剂（TiO2/EP）,对使用较为广泛的抗生素磺胺嘧啶（SDZ）进行了光催化降解研究,探讨了TiO2的负载量、溶液的初始浓度、初始pH、无机离子（HCO3^-、SO4^2-和Cl^-）和腐殖酸（HA）对SDZ降解效果的影响。结果表明：SDZ的光催化降解符合一级反应动力学方程;当TiO2最佳负载量为20 wt%,SDZ浓度为5 mg/L,pH=6.7,紫外光照射强度为1 000μW/cm^2,反应时间为45 min时,SDZ的降解率达到96%;HCO3^-在低浓度时能促进SDZ的光催化降解,高浓度时促进作用不明显;SO4^2-和Cl^-对SDZ的光催化降解有轻微的抑制作用;HA对SDZ光催化降解有显著的抑制作用,浓度越高,抑制作用越强。UV-TiO2/EP是一种去除水体中微污染SDZ的有效方法。     

Photodegradation of monochlorobenzene in titanium dioxide aqueous suspensions

The photocatalytic degradation of monochlorobenzene using titanium dioxide aqueous suspensions was performed under solar-simulated irradiation. The effects of concentration of monochlorobenzene, amount of titanium dioxide and pH of solution on the degradation were examined. The intermediates identified were three monochlorophenols, chlorohydroquinone and hydroxy-hydroquinone.     

水溶性巯基壳聚糖对污染土壤吸附态汞的解吸作用研究

用两种巯基化试剂半胱氨酸(Cys)和硫代乙醇酸(Thi)与壳聚糖(CTS)反应,制备了两种水溶性巯基壳聚糖,即Cys-CTS和Thi-CTS,对比研究了这两种巯基壳聚糖与CTS对被染毒土壤中吸附态汞的提取能力.结果表明,Thi-CTS在pH=3、质量浓度为0.5g/L、用量为20 mL的条件下.对汞的提取率为59.44%,相同条件下CTS和cys-CTS对汞的最高提取率只有31.81%和10.15%.     

Enhanced photocatalytic reduction reaction over Bi(3+)-TiO(2) nanoparticles in presence of formic acid as a hole scavenger

A series of Bi(3+)-doped TiO(2) (Bi(3+)-TiO(2)) catalysts with a doping concentration up to 2wt% were prepared by a sol-gel method. The prepared photocatalysts were characterized by different means to determine their chemical composition, surface structure and light absorption properties. The photocatalytic activity of different Bi(3+)-TiO(2) catalysts was evaluated in the photocatalytic reduction of nitrate in aqueous solution under UV illumination. In the experiments, formic acid was used as a hole scavenger to enhance the photocatalytic reduction reaction. The experiments demonstrated that nitrate was effectively degraded in aqueous Bi(3+)-TiO(2) suspension by more than 83% within 150min, while the pH of the solution increased from 3.19 to 5.83 due to the consumption of formic acid. The experimental results indicate that the presence of Bi(3+) in TiO(2) catalysts substantially enhances the photocatalytic reaction of nitrate reduction. It was found that the optimal dosage of 1.5wt% Bi(3+) in TiO(2) achieved the fastest reaction of nitrate reduction under the experimental condition. Bismuth ions deposit on the TiO(2) surface behaves as sites where electrons accumulate. Better separation of electrons and holes on the modified TiO(2) surface allows more efficient channeling of the charge carriers into useful reduction and oxidation reactions rather than recombination reactions. Two intermediate products of nitrite and ammonia during the reaction were also monitored to explore the possible mechanisms of photoluminescence quenching and photocatalytic reduction in the context of donor-acceptor interaction with electron trapping centers.