Contribution of individual components of a job cycle on overall severity of whole-body vibration exposure: a study in Indian mines

Drivers of earth-moving machines are exposed to whole-body vibration (WBV). In mining operations there can be a combination of relatively high magnitudes of vibration and long exposure times. Effective risk mitigation requires understanding of the main aspects of a task that pose a hazard to health. There are very few published studies of WBV exposure from India. This paper reports on a study that considered the contribution of the component phases of dumper operations, on the overall vibration exposure of the drivers. It shows that vibration magnitudes are relatively high, and that haulage tasks are the main contributor to the exposure. It is recommended that driver speed, haul road surfaces and vehicle maintenance/selection are optimized to ensure minimization of vibration. If this is not sufficient, operation times might need to be reduced in order to ensure that the health guidance caution zone from Standard No. ISO 2631-1:1997 is not exceeded.     

A methodology for assessment of long-term exposure to whole-body vibrations in vehicle drivers to propose preventive safety measures

Introduction: The appearance of musculoskeletal disorders (MDs) in professional drivers due to exposition to whole-body vibration (WBV) makes it relevant to assess this exposure. The European Directive 2002/44/EC has two methods to evaluate exposure to WBV (defined in ISO2631-1:2008). These methods evaluate the exposure associated with an 8-hour working day; however, MDs due to WBV could also be caused by accumulated exposure to vibrations over long term, and hence, the methods defined in the European directive may be limited in their ability to ensure the safety of workers exposed to WBV throughout their years of employment. Method: A detailed comparison and discussion of methods defined in the European Directive and the ISO2631-5:2018 was used as a starting point of the main results of this paper. On this basis, a new methodology for the management and organization of preventive measures is proposed to consider the assessment of ISO2631-5:2018 standard and the full working life of workers. Experimental data to assess exposure to WBV in heavy equipment vehicle (HEV) drivers under different road surface conditions and range of velocities were considered to illustrate the process of the proposed methodology. Results: The methods defined in the standards provide different assessments leading to a different possible consideration of safe operations when the risks associated with them may actually be high. The proposed methodology can be used with the aim of ensuring safety of workers throughout their working lives and providing an easy implementation of the calculations of ISO2631-5:2018 standard. Conclusions: A procedure to assess the health risk probability to which the HEV worker is exposed in terms of the exposure years and a different range of operational vehicle speeds is proposed and exemplified with a study case. Practical applications: This study provides a practical tool for the management of WBV exposure related to work-tasks in HEV drivers. Safety managers should consider the global exposition to WBV throughout their working life, and this research provides an easy tool to accomplish it.     

Studded and unstudded winter tires in fatal road accidents in Finland

Objective: The aim of the study was to compare the safety effects of studded and unstudded winter tires based on fatal road accidents.

Methods: The data included 958 road accidents involving a passenger car or van that occurred in Finland from November to March between 1997 and 2012.

Results: Comparing the proportions of winter tire type in accidents and in general traffic showed that the overall effect of tire type on the number of accidents was not significant, although studded tires reduced fatal accidents by 10–15%. Compared to unstudded tires, studded tires reduced accidents significantly only on bald ice in 2005–2012. Drivers using unstudded tires were more experienced and their profession was more frequently related to driving. In addition, the vehicle age was lower for vehicles with unstudded tires. On the other hand, the state of repair was less pertinent for unstudded than for studded tires. These confounding factors offset their effects to some degree.

Conclusions: The risk of fatal road accidents in winter between studded and unstudded tires does not differ significantly. However, the accident risk has recently been substantially higher on bald ice for unstudded than for studded tires. The magnitude of this risk difference is difficult to determine without specific information on exposure by road surface.     

Tire blow-outs and motorway accidents

During the period from 1996 to 2002, 60,397 vehicles were involved in crashes with property damage and/or injury on a French motorway network of 2000 km. It was observed that 6.7% of these accidents involved tire blow-outs. In 87% of cases, only one vehicle was involved in the accident. Tire blow-outs occurred in 6.5% of cars that represented more than 80% of the vehicles involved in crashes. The occurrence of this phenomenon is very high for vans (22%), though it concerns trucks less (2.5%). The proportion of tire blow-outs decreased from 1997, when it was 8.0%, to 5.9% in 2002. However, two main facts require examination: (1) On inter-urban motorways, crashes involving blow-outs of rear tires occur four times more frequently than for blow-outs of front tires. (2) The frequency of tire blow-outs is especially high for vans, and almost always involves rear tires. This higher frequency for rear tires is the result of two phenomena, which are indistinguishable given the data available: firstly, a four-wheel vehicle is more difficult to control if a blow-out occurs on a rear tire (confirmed experimentally); secondly, rear tires may be in poor condition more often than front tires, and so more prone to blow-outs. Consequently, users are strongly recommended to install the best tires on rear wheels. In practice, if only the front tires are replaced, which often occurs because they tend to be worn out more quickly than the rear ones (especially for front wheel drive vehicles), it is necessary to move the rear tires to the front and fit the new ones on the rear wheels. Very interesting technological developments are in progress that should reduce the number of tire blow-outs. However, considering the time necessary to renew the number of cars on the roads, this very simple and inexpensive recommendation should apply to all cars and especially to vans.     

Research on simultaneous impact of hand-arm and whole-body vibration

This article presents the results of laboratory tests on the combined effect of whole-body vibration (WBV) and hand-arm vibration (HAV). The reactions of subjects exposed to various combinations of vibration were recorded. The vibrotactile perception threshold (VPT) test identified changes caused by exposure to vibration. Ten male subjects met the criteria of the study. There were 4 series of tests: a reference test and tests after exposure to HAV, WBV, and after simultaneous exposure to HAV and WBV. An analysis of the results (6000 ascending and descending VPTs) showed that the changes in VPTs were greatest after simultaneous exposure to both kinds of vibration. The increase in VPT, for all stimulus frequencies, was then higher than after exposure to HAV or WBV only.     

Whole-body vibration knowledge survey of U.S. occupational safety and health professionals

Problem

Whole-body vibration (WBV) is an occupational issue of concern due to adverse health effects or simple discomfort and annoyance. Unlike in Europe, WBV is an emerging topic in the U.S. safety and health (S&H) professional community. We hypothesized that at least one-half of the U.S. occupational S&H professionals knew little or nothing about WBV.

Method

We conducted a cross-sectional study (survey) of WBV knowledge among members of the American Society of Safety Engineers. A Likert scale (1-none to 5-expert) was used to determine WBV topic knowledge levels (KL_1-5).

Results

Analysis of 2,764 responses revealed that 69.5% of the participants self-reported a less than basic WBV understanding. The WBV KL_1-5 mean for all participants was 1.94 ± 1.00, corresponding to an awareness of WBV without a depth of understanding.

Summary

Many at-risk U.S. workers may not be supported by occupational S&H professionals with adequate WBV knowledge.

Impact on Industry

A significant number of U.S. workers may be exposed to unhealthy levels of whole-body vibration. However, the U.S. occupational safety and health community is generally unprepared to anticipate, monitor, and control the whole-body vibration hazard.     

Lower back pain and its association with whole-body vibration and manual materials handling among commercial drivers in Sabah

A cross-sectional study was undertaken to determine the prevalence of lower back pain (LBP) and its association with whole-body vibration (WBV) and manual materials handling (MMH). We studied 110 commercial vehicle drivers using a self-administered questionnaire and the VI-400Pro human vibration monitor. Prevalence of LBP was 66.4%. The percentage of drivers who had frequent manual handling of heavy loads was 45.5% and those who handled heavy loads in awkward postures accounted for 86.4%. Daily vibration A(8) averaged on the z axis was 0.25 (0.06) m·s^?2 and at vector sum was 0.29 (0.07) m·s^?2. Daily vibration exposures on the z axis, frequent manual handling of heavy loads and awkward posture during MMH were significantly associated with LBP. Drivers who are exposed to WBV and frequently handle heavy loads manually and with awkward postures probably have more LBP than drivers who are exposed to only one of these risk factors.     

基于SP12汽车安全胎压监测系统设计与实现

为了降低胎压监测系统的功耗和优化胎压监测系统的显示方式,设计了一种基于SP12传感器的安全胎压监测系统方案。从硬件和软件两方面描述了系统的设计实现方法。在硬件设计上,采用车载电源和充电电池两种方式对主机进行供电,同时,系统应用SP12多功能传感器降低功耗。在软件设计上,着重介绍了轮胎采集模块和中央显示模块的设计。为进一步优化系统的显示方式,中央显示模块采用带触摸屏的LCD显示器作为人机交互接口。实际测试结果表明,该系统可实时监测每个轮胎内部的实际温度、压力和电压,确定故障轮胎并实时报警,有效避免爆胎事故的发生。另外,系统在安全性、低功耗以及可靠性方面具有一定的优势,这也符合智能车辆研究的发展趋势。     

The moderating role of task characteristics in determining responses to a stressful work simulation

Two experimental studies were conducted to examine whether the stress‐buffering effects of behavioral control on work task responses varied as a function of procedural information. Study 1 manipulated low and high levels of task demands, behavioral control, and procedural information for 128 introductory psychology students completing an in‐basket activity. ANOVA procedures revealed a significant three‐way interaction among these variables in the prediction of subjective task performance and task satisfaction. It was found that procedural information buffered the negative effects of task demands on ratings of performance and satisfaction only under conditions of low behavioral control. This pattern of results suggests that procedural information may have a compensatory effect when the work environment is characterized by a combination of high task demands and low behavioral control. Study 2 (N=256) utilized simple and complex versions of the in‐basket activity to examine the extent to which the interactive relationship among task demands, behavioral control, and procedural information varied as a function of task complexity. There was further support for the stress‐buffering role of procedural information on work task responses under conditions of low behavioral control. This effect was, however, only present when the in‐basket activity was characterized by high task complexity, suggesting that the interactive relationship among these variables may depend on the type of tasks performed at work. Copyright © 1999 John Wiley & Sons, Ltd.     

Portable ladder assessment tool development and validation – Quantifying best practices in the field

Many causes for falls from ladders in construction are related to the user’s activities; however, the extent to which users comply with ladder use best practices is unknown and has not been well quantified before. We developed and tested an audit tool that assesses compliance with best practices guidelines for portable-ladder-use designed for applications in the construction industry. Implemented on a hand-held computer, the assessment tool consisted of a series of check-lists categorized in four groups; ladder condition, setup, moving on a ladder, and completing tasks from a ladder. For these four observational categories, the resulting tool contained 31 and 33 questions for step and extension ladders, respectively. Three individuals trained to use the tool scored a set of photographs and videos depicting 25 ladder conditions, 20 ladder setups, 10 users moving on ladders, and 13 users completing tasks from a ladder for a total of 78 observations. The assessment tool had good agreement across and within raters. For the three raters, agreement ranged from 79% to 97% across the questions. Within one subject, kappa coefficients for the intra-rater reliability ranged from 0.67 to 0.91. The tool offers a practical method to quantify best practices associated with ladder use that can ultimately inform targeted intervention efforts.     

Commentary: legal minimum tread depth for passenger car tires in the U.S.A.--a survey

Available tire traction is a significant highway safety issue, particularly on wet roads. Tire-roadway friction on dry, clean roads is essentially independent of tread depth, and depends primarily on roadway surface texture. However, tire-wet-roadway friction, both for longitudinal braking and lateral cornering forces, depends on several variables, most importantly on water depth, speed and tire tread depth, and the roadway surface texture. The car owner-operator has control over speed and tire condition, but not on water depth or road surface texture. Minimum tire tread depth is legislated throughout most of the United States and Europe. Speed reduction for wet road conditions is not.A survey of state requirements for legal minimum tread depth for passenger vehicle tires in the United States is presented. Most states require a minimum of 2/32 of an inch (approximately 1.6 mm) of tread, but two require less, some have no requirements, and some defer to the federal criterion for commercial vehicle safety inspections. The requirement of 2/32 of an inch is consistent with the height of the tread-wear bars built in to passenger car tires sold in the United States, but the rationale for that requirement, or other existing requirements, is not clear. Recent research indicates that a minimum tread depth of 2/32 of an inch does not prevent significant loss of friction at highway speeds, even for minimally wet roadways. The research suggests that tires with less than 4/32 of an inch tread depth may lose approximately 50 percent of available friction in those circumstances, even before hydroplaning occurs. It is concluded that the present requirements for minimum passenger car tire tread depth are not based upon rational safety considerations, and that an increase in the minimum tread depth requirements would have a beneficial effect on highway safety.     

Structural equation modelling of lower back pain due to whole-body vibration exposure in the construction industry

Whole-body vibration (WBV) exposure is a health hazard among workers, causing lower back pain (LBP) in the construction industry. This study examines key factors affecting LBP due to WBV exposure using exploratory factor analysis and structural equation modelling. The results confirm five key factors (equipment, job related, organizational, personal, social context) with their 17 associated items. The organizational factor is found the most important, as it influences the other four factors. The results also show that appropriate seat type, specific training programme, job rotation, workers’ satisfaction and workers’ physical condition are crucial in reducing LBP due to WBV exposure. Moreover, provision of new machines without proper training and good working condition might not help reduce LBP due to WBV exposure. The results help the construction companies to better understand key factors affecting LBP due to WBV exposure, and to plan for a better health improvement programme.     

Teens' distracted driving behavior: Prevalence and predictors

IntroductionTeen drivers' over-involvement in crashes has been attributed to a variety of factors, including distracted driving. With the rapid development of in-vehicle systems and portable electronic devices, the burden associated with distracted driving is expected to increase. The current study identifies predictors of secondary task engagement among teenage drivers and provides basis for interventions to reduce distracted driving behavior. We described the prevalence of secondary tasks by type and driving conditions and evaluated the associations between the prevalence of secondary task engagement, driving conditions, and selected psychosocial factors.MethodsThe private vehicles of 83 newly-licensed teenage drivers were equipped with Data Acquisition Systems (DAS), which documented driving performance measures, including secondary task engagement and driving environment characteristics. Surveys administered at licensure provided psychosocial measures.ResultsOverall, teens engaged in a potentially distracting secondary task in 58% of sampled road clips. The most prevalent types of secondary tasks were interaction with a passenger, talking/singing (no passenger), external distraction, and texting/dialing the cell phone. Secondary task engagement was more prevalent among those with primary vehicle access and when driving alone. Social norms, friends' risky driving behaviors, and parental limitations were significantly associated with secondary task prevalence. In contrast, environmental attributes, including lighting and road surface conditions, were not associated with teens' engagement in secondary tasks.ConclusionsOur findings indicated that teens engaged in secondary tasks frequently and poorly regulate their driving behavior relative to environmental conditions. Practical applications: Peer and parent influences on secondary task engagement provide valuable objectives for countermeasures to reduce distracted driving among teenage drivers.     

Driving context influences drivers' decision to engage in visual–manual phone tasks: Evidence from a naturalistic driving study

IntroductionVisual–manual (VM) phone tasks (i.e., texting, dialing, reading) are associated with an increased crash/near-crash risk. This study investigated how the driving context influences drivers' decisions to engage in VM phone tasks in naturalistic driving.MethodVideo-recordings of 1,432 car trips were viewed to identify VM phone tasks and passenger presence. Video, vehicle signals, and map data were used to classify driving context (i.e., curvature, other vehicles) before and during the VM phone tasks (N = 374). Vehicle signals (i.e., speed, yaw rate, forward radar) were available for all driving.ResultsVM phone tasks were more likely to be initiated while standing still, and less likely while driving at high speeds, or when a passenger was present. Lead vehicle presence did not influence how likely it was that a VM phone task was initiated, but the drivers adjusted their task timing to situations when the lead vehicle was increasing speed, resulting in increasing time headway. The drivers adjusted task timing until after making sharp turns and lane change maneuvers. In contrast to previous driving simulator studies, there was no evidence of drivers reducing speed as a consequence of VM phone task engagement.ConclusionsThe results show that experienced drivers use information about current and upcoming driving context to decide when to engage in VM phone tasks. However, drivers may fail to sufficiently increase safety margins to allow time to respond to possible unpredictable events (e.g., lead vehicle braking).Practical applicationsAdvanced driver assistance systems should facilitate and possibly boost drivers' self-regulating behavior. For instance, they might recognize when appropriate adaptive behavior is missing and advise or alert accordingly. The results from this study could also inspire training programs for novice drivers, or locally classify roads in terms of the risk associated with secondary task engagement while driving.     

Assessing drivers' response during automated driver support system failures with non-driving tasks

IntroductionWith the increase in automated driver support systems, drivers are shifting from operating their vehicles to supervising their automation. As a result, it is important to understand how drivers interact with these automated systems and evaluate their effect on driver responses to safety critical events. This study aimed to identify how drivers responded when experiencing a safety critical event in automated vehicles while also engaged in non-driving tasks.MethodIn total 48 participants were included in this driving simulator study with two levels of automated driving: (a) driving with no automation and (b) driving with adaptive cruise control (ACC) and lane keeping (LK) systems engaged; and also two levels of a non-driving task (a) watching a movie or (b) no non-driving task. In addition to driving performance measures, non-driving task performance and the mean glance duration for the non-driving task were compared between the two levels of automated driving.ResultsDrivers using the automated systems responded worse than those manually driving in terms of reaction time, lane departure duration, and maximum steering wheel angle to an induced lane departure event. These results also found that non-driving tasks further impaired driver responses to a safety critical event in the automated system condition.ConclusionIn the automated driving condition, driver responses to the safety critical events were slower, especially when engaged in a non-driving task.Practical applicationTraditional driver performance variables may not necessarily effectively and accurately evaluate driver responses to events when supervising autonomous vehicle systems. Thus, it is important to develop and use appropriate variables to quantify drivers' performance under these conditions.     

Influence of task demands on occupational stress: Gender differences

IntroductionOccupational stress is a common phenomenon in our society, and generates problems for both workers' health and the functioning of organizations. Over past decades numerous studies have examined occupational stress from the perspective of gender, offering somewhat contradictory results. Some of them found no differences and others indicated that either men or women suffer from greater amounts of occupational stress.MethodThe purpose of this study was to analyze gender differences in stress in situations that involve certain occupational demands. The data used were taken from a random sample population of 11,054 (5,917 men and 5,137 women) from the VI National Survey on Working Conditions (NSWC) which was conducted in Spain in 2007. To carry out this study, a probabilistic model was constructed using Bayesian networks, with the following variables related to task demands: working with tight deadlines, quick work, intellectually demanding work, complicated tasks, repetitive tasks, excessive work, and work demanding high attention levels.ResultsThe results of this study reveal that: the indicators studied significantly increased stress levels; women initially had higher stress levels than men; and when exposed to determined task demands, stress differences between genders tended to increase.Impact on IndustryCompanies need to consider the gender of their workers when assigning tasks in high demand/stress jobs.     

Sensitivity evaluation of the visual,tactile, and auditory detection response task method while driving

Objectives: In this article, we evaluate the sensitivity to cognitive load of 3 versions of the Detection Response Task method (DRT), proposed in ISO Draft Standard DIS-17488.

Methods: We present a user study with 30 participants in which we compared the sensitivity to cognitive load of visual, audio, and tactile DRT in a simulated driving environment. The amount of cognitive load was manipulated with secondary n-back tasks at 2 levels of difficulty (0-back and 1-back). We also explored whether the DRT method is least sensitive to cognitive load when the stimuli and secondary task are of the same modality. For this purpose, we used 3 forms to present the n-back task stimuli: visual, audio, and tactile. Responses to the task were always vocal. The experiment was based on a between-subject design (the DRT modalities) with 2 levels of within-subject design study (modalities and difficulty of the secondary n-back tasks). The participants' primary task in the study was to drive safely, and a second priority was to answer to DRT stimuli and perform secondary tasks.

Results: The results indicate that all 3 versions of the DRT tested were sensitive to detecting the difference in cognitive load between the reference driving period and driving and engaging in the secondary tasks. Only the visual DRT discriminated between the 0-back and 1-back conditions on mean response time. Contrary to expectations, no interaction was observed between DRT modality and the stimuli modality used for presentation of the secondary tasks.

Conclusions: None of the 3 methods of presenting DRT stimuli showed a consistent advantage in sensitivity in differentiating multiple levels of cognitive load if all response times, hit rates, and secondary task performance are considered. If only response time is considered, the visual presentation of the DRT stimulus used in this study showed some advantages. In interpreting these data, it should be noted that the methods of DRT stimulus presentation varied somewhat from the currently proposed draft ISO standard and it is possible that the relative salience level of the visual DRT stimulus influenced the findings. It is further suggested that more than 2 levels of difficulty of the n-back task should be considered for further investigation of the relative sensitivity of different DRT stimuli modalities. Parameters that indicate change in cognitive load (response time, hit rate, task performance) should be analyzed together in assessing the overall impact on the driver and not individually, in order to obtain a fuller insight of the assessed cognitive load.     

Study of the possible relationships between tramway front-end geometry and pedestrian injury risk

Objectives: The aim of this article is to report on the possible relationships between tramway front-end geometry and pedestrian injury risk over a wide range of possible tramway shapes.

Methods: To study the effect of tramway front-end shape on pedestrian injury metrics, accidents were simulated using a custom parameterized model of tramway front-end and pedestrian models available with the MADYMO multibody solver. The approach was automated, allowing the systematic exploration of tramway shapes in conjunction with 4 pedestrian sizes (e.g., 50th percentile male or M50).

Results: A total of 8,840 simulations were run, showing that the injury risk is more important for the head than for other body regions (thorax and lower extremities). The head of the M50 impacted the windshield of the tramway in most of the configurations. Two antagonist mechanisms affecting impact velocity of the head and corresponding head injury criterion (HIC) values were observed. The first is a trunk rotation resulting from an engagement of the lower body that can contribute to an increase in head velocity in the direction of the tram. The second is the loading of the shoulder, which can accelerate the upper trunk and head away from the windshield, resulting in lower impact velocities. Groups of design were defined based on 2 main parameters (windshield height and offset), some of which seem more beneficial than others for tramway design. The pedestrian size and tramway velocity (30 vs. 20?km/h) also affected the results.

Conclusions: When considering only the front-end shape, the best strategy to limit the risk of head injury due to contact with the stiff windshield seems to be to promote the mechanism involving shoulder loading. Because body regions engaged vary with the pedestrian size, none of the groups of designs performed equally well for all pedestrian sizes. The best compromise is achieved with a combination of a large windscreen offset and a high windscreen. Conversely, particularly unfavorable configurations are observed for low windshield heights, especially with a large offset. Beyond the front-end shape, considering the stiffness of the current windshields and the high injury risks predicted for 30?km/h, the stiffness of the windshield should be considered in the future for further gains in pedestrian safety.     

Task type as a moderator of positive/negative feedback effects on motivation and performance: A regulatory focus perspective

Applying Higgins' regulatory focus theory, we hypothesized that the effect of positive/negative feedback on motivation and performance is moderated by task type, which is argued to be an antecedent to situational regulatory focus (promotion or prevention). Thus, first we demonstrated that some tasks (e.g., tasks requiring creativity) are perceived as promotion tasks, whereas others (e.g., those requiring vigilance and attention to detail) are perceived as prevention tasks. Second, as expected, our tests in two studies of the moderation hypothesis showed that positive feedback increased self‐reported motivation (meta‐analysis across samples: N = 315, d = 0.43) and actual performance (N = 55, d = 0.67) among people working on promotion tasks, relative to negative feedback. Positive feedback, however, decreased motivation (N = 318, d = ?0.33) and performance (N = 55, d = ?0.37) among individuals working on prevention tasks, relative to negative feedback. These findings suggest that (a) performance of different tasks can affect regulatory focus and (b) variability in positive/negative feedback effects can be partially explained by regulatory focus and task type. Copyright © 2010 John Wiley & Sons, Ltd.     

Effects of multitasking on operator performance using computational and auditory tasks

This study investigated the effects of multiple cognitive tasks on human performance. Twenty-four students at North Carolina A&;T State University participated in the study. The primary task was auditory signal change perception and the secondary task was a computational task. Results showed that participants' performance in a single task was statistically significantly different from their performance in combined tasks: (a) algebra problems (algebra problem primary and auditory perception secondary); (b) auditory perception tasks (auditory perception primary and algebra problems secondary); and (c) mean false-alarm score in auditory perception (auditory detection primary and algebra problems secondary). Using signal detection theory (SDT), participants' performance measured in terms of sensitivity was calculated as ?0.54 for combined tasks (algebra problems the primary task) and ?0.53 auditory perceptions the primary task. During auditory perception tasks alone, SDT was found to be 2.51. Performance was 83% in a single task compared to 17% when combined tasks.