Impact of microbial activity on copper, lead and nickel mobilization during the bioremediation of soil PAHs

A fungal bioremediation method using P. frequentans removed up to 75% of phenanthrene with the addition of water and nutrients over a period of 30 d. During the bioremediation process, changes in metal behavior were monitored by an in situ technique (diffusive gradients in thin-films, DGT) and by soil solution chemistry. DGT provided absolute data on fluxes from the solid phase to the DGT device and relative trends of concentrations of the most labile metal species. DGT response indicated that bioremediation increases metal mobilization from the solid phase. Filtration provided data on the concentrations of solution phase (<0.45 microm) metal. In all case, metal fluxes and concentrations significantly increased after the bioremediation process began. Fluxes increased from <0.1 pg cm(-2)s(-1) before bioremediation to between 0.2 and 0.5 pg cm(-2)s(-1) after bioremediation. Metal concentrations in the soils solution (filtration at 0.45 microm) increased from 2 to 10 microg l(-1) (Cu), 1-4 microgl(-1) (Pb) and from 40 to 140 microg l(-1) (Ni) after bioremediation. Although over a short time period, these data strongly indicated that there was remobilization of metal from solid to solution (and thus to the DGT device) directly due to the bioremediation process. Although the mechanism was not unambiguously identified, it was shown not to be related to small changes in bulk pH over time and was attributed to the microbial action on the surface of the soil solid phase, releasing metal into solution. Additionally, differences in metal concentration and flux were observed in sterilized and non-sterilized soils and in the absence or presence of phenanthrene. The results indicated that the bioremediation of soil by P. frequentans increased the flux, lability and mobility of trace metal species and therefore the likely metal bioavailability to plants.     

In situ fixation of metals in soils using bauxite residue: chemical assessment

Contamination of soils with heavy metals and metalloids is a widespread problem all over the world. Low cost, non-invasive, in situ technologies are required for remediation processes. We investigated the efficiency of a bauxite residue (red mud) to fix heavy metals in two soils, one contaminated by industrial activities (French soil), and one by sewage sludge applications (UK soil). This Fe-oxide rich material was compared with lime, or beringite, a modified aluminosilicate that has been used for in situ fixation processes. Four different crop species were successively grown in pots. Metal concentrations in the soil pore waters were analyzed during the growing cycles. At the end of the experiment fluxes of heavy metals were measured using a diffusive gradient in thin film technique (DGT). Furthermore, a sequential extraction procedure (SEP) and an acidification test were performed to investigate the mechanisms of metal fixation by different soil amendments. In both soils, the concentrations of metals in the soil pore water and metal fluxes were greatly decreased by the amendments. An application of 2% red mud performed as well as beringite applied at 5%. Increasing soil pH was a common mechanism of action for all the amendments. However, the red mud amendment shifted metals from the exchangeable to the Fe-oxide fraction, and decreased acid extractability of metals. The results suggest that specific chemisorption, and possibly metal diffusion into oxide particles could also be the mechanisms responsible for the fixation of metals by red mud.     

Quantitative assessment of soil parameter (KD and TC) estimation using DGT measurements and the 2D DIFS model

Diffusive gradients in thin films (DGT) is a dynamic, in situ measuring technique that can be used to supply diverse information on concentrations and behaviour of solutes. When deployed in soils and sediments, quantitative interpretation of DGT measurements requires the use of a numerical model. An improved version of the DGT induced fluxes in soils and sediments model (DIFS), working in two dimensions (2D DIFS), was used to investigate the accuracy with which DGT measurements can be used to estimate the distribution coefficient for labile metal (KD) and the response time of the soil to depletion (TC). The 2D DIFS model was used to obtain values of KD and TC for Cd, Zn and Ni in three different soils, which were compared to values determined previously using 1D DIFS for these cases. While the 1D model was shown to provide reasonable estimates of KD, the 2D model refined the estimates of the kinetic parameters. Desorption rate constants were shown to be similar for all three metals and lower than previously thought. Calculation of an error function as KD and TC are systematically varied showed the spread of KD and TC values that fit the experimental data equally well. These automatically generated error maps reflected the quality of the data and provided an appraisal of the accuracy of parameter estimation. They showed that in some cases parameter accuracy could be improved by fitting the model to a sub-set of data.     

Evaluation of heavy metal lability in polluted soils by a cation exchange batch procedure

A new extraction procedure with cationic exchange resins is proposed for the assessment of heavy metal lability in polluted soils. This method classifies soluble metal compounds in three levels according to their lability: very labile, moderately labile and non-labile. The concept of lability is based on the use of resins with different ability to interact with metals. The proposed procedure was applied to five samples of polluted soils. In the five soils, soluble Cd was found to be very labile, soluble Ni and Pb were mostly non-labile, Mn and Zn lability depended on the soil, while Cu had a fraction of moderately labile forms in four of the five soils. The resin extraction procedure was compared with the DTPA and CaCl2 extractions.     

Measurement of dynamic mobilization of trace metals in sediments using DGT and comparison with bioaccumulation in Chironomus riparius: first results of an experimental study

Sediments in aquatic ecosystems are often contaminated as a result of anthropogenic activities. Sediments and benthic organisms have been used to monitor trace metals contamination. However, due to the high variability of contaminant bioavailability, the attempt to link metal concentration in sediments and contamination of the organisms or ecotoxicological effect often lead to disappointing results. The technique of diffusive gradients in thin films (DGT) has been proposed as a relevant tool to study metal bioavailability, for example for accumulation in plants. In the present study, laboratory microcosm experiments were conducted with six contaminated sediments to compare metal accumulation in DGT and bioaccumulation in a chironomid (Chironomus riparius) for Cu, Cd and Pb . Metal accumulation in DGT was measured over time then modelled to determine two parameters of the dynamic response of the metals to DGT deployment: the size of the particulate labile pool and the kinetic of the solid-dissolved phase exchange. The mobility of metals was found metal and sediment dependent. A significant relationship between metal accumulated in DGT and bioaccumulated in chironomids was found for Cu and Pb. However, total metals in sediments were the best predictors of bioaccumulation. Nevertheless, the knowledge of the metals dynamic enhanced our ability to explain the different biological uptake observed in sediments of similar total metal concentrations.     

Copper uptake by Elsholtzia splendens and Silene vulgaris and assessment of copper phytoavailability in contaminated soils

Tolerance and metal uptake are two essential characteristics required for phytoextraction of metals from contaminated soils. We compared tolerance and Cu uptake of Elsholtzia splendens (reported previously to be a Cu hyperaccumulator) with Silene vulgaris (the Imsbach population, a well-known Cu-tolerant excluder species), using 30 soils varying widely in total Cu concentration (19-8645 mg kg(-1)). We further investigated the effectiveness of different soil testing methods for predicting plant metal uptake. The results showed that both Elsholtzia splendens and Silene vulgaris were tolerant to Cu, especially Silene vulgaris. However, Elsholtzia splendens did not hyperaccumulate Cu, but behaved as a typical Cu excluder like Silene vulgaris. The concentrations of Cu in both plants correlated more closely with 1 M NH4NO3 extractable Cu, soil solution Cu, or effective Cu concentration determined using DGT, than with soil total Cu, EDTA extractable Cu or free Cu2+ activity. The relationships between soil solution properties and root Cu concentrations were further investigated using multiple regression. The results showed that increasing soil solution pH increased root Cu concentration when free Cu2+ activity was held constant, suggesting a higher phytoavailability of free Cu2+ at a higher pH. Soil solution DOC appeared to play two contrasting roles on the phytoavailability of Cu: (1) reducing Cu availability by complexing Cu; and (2) increasing Cu availability at the same level of free Cu2+ activity by providing a strong buffer for free Cu2+. The results are consistent with the intensity/capacity concept for phytoavailability of metals in soils.     

Trace metal speciation and fluxes within a major French wastewater treatment plant: impact of the successive treatments stages

Seven metals (Cd, Co, Cr, Cu, Fe, Ni and Pb) were monitored at the Seine-Aval wastewater treatment plant during 6 sampling campaigns in April 2004. Particulate and dissolved metals have been measured in 24 h composite samples at each treatment stage (primary settling, secondary activated sludge and tertiary flocculation by FeCl₃). In addition, the diffusive gradient in thin film technique (DGT) was used to determine the dissolved inert and labile metal fraction. Although all treatment stages were able to decrease particulate metals concentrations in wastewater, most dissolved metals concentrations were mainly affected during primary settling. This unexpected result was attributed to tertiary sludge filtrate recirculation. Metals added via the FeCl₃ reagent at the tertiary treatment were shown to lower the overall Cr removal from wastewater and to enrich Ni in effluents. The plant operating conditions (recirculation and reagent addition) appear therefore as important as treatment processes for the metals removal. Total metal fluxes were highly decreased by the whole treatment plant for Cd, Cr, Cu and Pb and to a lesser extend for Co and Ni. However, the labile metal fluxes were poorly decreased for Cu (18%), not significantly decreased for Ni and increased for Fe. The labile fraction of Cd, Co and Cr was not detectable at any stage of the plant. Discharged labile fluxes, at least for Ni, were potentially significant compared to the labile metal fluxes in the river measured downstream the plant. Treated urban wastewater discharges should be carefully considered as a possible source of bioavailable trace metals.     

Speciation of Cd and Zn in contaminated soils assessed by DGT-DIFS, and WHAM/Model VI in relation to uptake by spinach and ryegrass

A pot experiment was carried out to investigate the impact of Cd and Zn extractability in soil and speciation in pore water of industrial contaminated soils, on metal concentration in a metal sensitive species like spinach (Spinacia oleracea) and a more metal tolerant species like Italian ryegrass (Lolium multiflorum). For chemical speciation of Cd and Zn in pore water, WHAM/Model VI version 6.0 was used. The DGT technique was used to determine the effective concentration, C(E), of Cd and Zn in soils. The free ion activity in pore water correlated well with the contents in plants, and there was a linear relationship between the C(E) values and the concentration of Cd and Zn in both spinach and ryegrass in the non-toxic range. However, the C(E) values usually overestimated the plant contents when plants, particularly the spinach plants, were subjected to toxic concentration in the pore water. Metal uptake decreased in plants affected by toxicity, whereas metal binding to the Chelex resin did not. Thus, we found no linear relationship between the C(E) and metal contents in spinach, whereas a linear relationship was found between C(E)-Zn and the Zn concentration in ryegrass (r2=0.96, p<0.001). For Cd in ryegrass this relationship was weak (r2=0.53, p=0.18). This study indicates that the transport of metals from labile metal pools to the DGT-resin is linearly related to plant uptake only when plants are growing well, and that the applicability of DGT as an indicator for plant uptake seems species dependent.     

Metal concentrations in used engine oils: Relevance to site assessments of soils

Used engine oils contain metals, which upon entering soils may pose risks to human health or the environment. In this study, previously published concentrations of 23 metals in 213 used engine oil samples from the early 1970s to the mid-1990s are statistically evaluated. Neat (100%) used engine oils were found to contain relatively high concentrations of lead, calcium, and zinc, attributable to piston blow-by of leaded gasoline, calcium salt detergent additives, and zinc-bearing anti-corrosion/anti-oxidation additives, respectively. Wear metal concentrations were lower. The lead concentration in used engine oils in the U.S. declined between the 1970s and early 1990s, potentially providing a basis to constrain the “age” of used engine oil(s) in soils. The concentrations of 23 metals in used engine oils were compared to soil risk benchmarks in 15 representative jurisdictions in the U.S., Canada, Australia, and Europe. The maximum concentrations in neat (100%) used engine oil of eight metals – Be, Co, Fe, Mn, Ni, Se, Ag, and Ti – were lower than their collective minimum benchmarks in soils for the jurisdictions surveyed, indicating their concentrations in soils could not be reasonably expected to exceed any soil benchmarks. Nine metals (As, Ba, Cd, Cr, Cu, Pb, Sn, V and Zn), but particularly arsenic, cadmium, lead, tin, and zinc, were identified as potential contaminants of concern (PCOC) for soils from locations impacted with used engine oils, owing to their higher median concentrations (i.e., 2.5, 1.4, 1038, 5.0, and 922 mg/kg in oil, respectively) relative to most soil benchmarks. Site-specific benchmarks and metal concentrations at reasonable oil in soil concentrations require consideration when developing the suite of PCOC metal analytes for conducting site assessments of soils impacted by used engine oil.     

Determination of chemical availability of cadmium and zinc in soils using inert soil moisture samplers

A rapid method for extracting soil solutions using porous plastic soil-moisture samplers was combined with a cation resin equilibration based speciation technique to look at the chemical availability of metals in soil. Industrially polluted, metal sulphate amended and sewage sludge treated soils were used in our study. Cadmium sulphate amended and industrially contaminated soils all had > 65% of the total soil solution Cd present as free Cd2+. However, increasing total soil Cd concentrations by adding CdSO4 resulted in smaller total soil solution Cd. Consequently, the free Cd2+ concentrations in soil solutions extracted from these soils were smaller than in the same soil contaminated by sewage sludge addition. Amendment with ZnSO4 gave much greater concentrations of free Zn2+ in soil solutions compared with the same soil after long-term Zn contamination via sewage sludge additions. Our results demonstrate the difficulty in comparing total soil solution and free metal ion concentrations for soils from different areas with different physiochemical properties and sources of contamination. However, when comparing the same Woburn soil, Cd was much less available as Cd2+ in soil solution from the CdSO4 amended soils compared with soil contaminated by about 36 years of sewage sludge additions. In contrast, much more Zn was available in soil solution as free Zn2+ in the ZnSO4 amended soils compared with the sewage sludge treated soils.     

Copper bioavailability in the rhizosphere of maize (Zea mays L.) grown in two Italian soils

In this study, potentially bioavailable copper was estimated in two soils (a fungicide polluted and a natural soil) using a passive sampling technique, DGT. As plants can alter copper mobility and bioavailability in the soil, the rhizosphere properties of Zea mays L. were investigated using rhizoboxes.

Compared to the total concentration, the soluble and the potentially bioavailable copper concentration in the bulk soils were generally low (less than 0.20% and 0.06% respectively), with a sixfold increase in the rhizosphere of the polluted soil. Our results suggest that maize cultivation in a polluted vineyard soil could increase the potentially available fraction of copper. DGTs showed a good sensitivity to soil properties and to root-induced changes in the rhizosphere, but the potentially bioavailable copper could not be related to the copper concentration in the above ground parts of maize. The results suggest that DGT may be used to predict some effects of the cultivation of polluted soils, for example, metal mobility and increased availability, but they cannot mimic the uptake of a tolerant plant.

For both soils, dissolved organic carbon (DOC) concentrations were threefold higher in the rhizosphere than in the bulk soil, whilst bioaccumulation in leaves and roots was not significant. DOC production, usually effective in ion mobilization and assimilation, may help also in the reduction of Cu uptake at toxic concentrations. The sequestration of available Cu in soil and soil solution by DOC seems to contribute to maize tolerance.     

重金属污染土壤中提高植物提取修复功效的探讨

随着对重金属超积累植物研究的加深 ,用植物提取修复技术来改良重金属污染的土壤已逐步进入实用阶段。本文所探讨的提高此技术功效的方法基于两个方面 :提高土壤溶液中重金属的浓度 ,促进植物对重金属的吸收 ;根据已了解的超积累的生理机制可能采取的一些措施     

Fractionation and bioavailability of metals and their impacts on microbial properties in sewage irrigated soil

A study was conducted to evaluate the effect of long-term irrigation of sewage contaminated with heavy metals like Cd, Cr, Cu and Pb on microbial and biochemical parameters of soils of West Bengal, India. The microbial parameters included microbial biomass carbon (MBC), microbial metabolic quotient; the biochemical parameters included fluorescein diacetate hydrolyzing activity, beta-glucosidase, urease, phosphatase, and aryl sulphatase activities. A sequential extraction technique was used to quantify water soluble, exchangeable, carbonate bound, Fe/Mn-oxide bound, organically bound, and residual metal fractions. Metal concentrations in the two most labile fractions (i.e., water soluble and exchangeable fractions) were generally low. Total metal concentrations at each site seemed to be associated with soil amorphous Fe and Al minerals. The MBC and the enzymes studied were significantly and negatively correlated with water soluble and exchangeable metals but not significantly correlated with other forms, indicating that water soluble and exchangeable forms exerted a strong inhibitory effect on the soil microbial and biochemical parameters. It was concluded that irrigating soils with metal contaminated sewage seemed to damage soil quality in the long term.     

Retention and distribution of heavy metals in mangrove soils receiving wastewater

The distribution and chemical fractionation of heavy metals retained in mangrove soils receiving wastewater were examined by soil column leaching experiments. The columns, filled with mangrove soils collected from two swamps in Hong Kong and the People's Republic of China, were irrigated three times a week for 150 days with synthetic wastewater containing 4 mg l(-1) Cu, 20 mg l(-1) Zn, 20 mg l(-1) Mn and 0.4 mg l(-1) Cd. Soil columns leached with artificial seawater (without any heavy metals) were used as the control. At the end of the leaching experiments, soil samples from each column were divided into five layers according to its depth viz. 0-1, 1-3, 3-5, 5-10 and > 10 cm, and analyzed for total and extractable heavy metal content. The fractionation of heavy metals in the surface soil samples (0-1 cm) was investigated by the sequential extraction technique. In both types of mangrove soils, the surface layer (0-1 cm) of the columns receiving wastewater had significantly higher concentrations of total Cu, Cd, Mn and Zn than the control. Concentrations declined significantly with soil depth. The proportion of exchangeable heavy metals in soils receiving wastewater was significantly higher than that found in the control, about 30% of the total heavy metals accumulated in the soil masses of the treated columns were extracted by ammonium acetate at pH 4. The sequential extraction results show that in native mangrove soils (the soils without any treatment), the major portion of Cu, Zn, Mn and Cd was associated with the residual and precipitated fractions with very low concentrations in more labile phases. However, in mangrove soils receiving wastewater, a significantly higher percentage of Mn, Zn and Cd was found in the water-soluble and exchangeable fractions. Copper appeared to be more strongly adsorbed in mangrove soils than the other heavy metals. In general, heavy metal accumulation in the surface mangrove soils collected in Hong Kong was higher than those in the PRC, although the metals in the latter soil type were more strongly bound. These findings suggest that whether the heavy metal retained in managrove soils becomes a secondary source or a permanent sink would depend on the kinds of heavy metals and also the types of mangrove soils.     

Metal mobility at an old, heavily loaded sludge application site

This study was undertaken to determine the present distribution and mobility of sludge-applied metals at an old land application site. Trace metals concentrations were determined for soils (using 4 M HNO3 extracts), soil leachates (collected with passive wick lysimeters over a 2.5-year period), and plant tissue from a field site which received a heavy loading of wastewater sludge in 1978 and an adjacent control plot. Blue dye was used to indicate preferential percolate flowpaths in the sludge plot soil for sampling and comparison with bulk soil metals concentrations. After nearly 20 years, metals in the sludge plot leachate were found at significantly greater concentrations than in the control plot, exceeding drinking water standards for Cd, Ni, Zn, and B. Annual metals fluxes were only a fraction of the current soil metal contents, and do not account for the apparent substantial past metals losses determined in a related study. Elevated Cd, Cu, and Ni levels were found in grass growing on the sludge plot. Despite heavy loadings, fine soil texture (silty clay loam) and evidence of past and ongoing metals leaching, examination of the bulk subsoil indicated no statistically significant increases in metals concentrations (even in a calcareous subsoil horizon with elevated pH) when comparing pooled sludge plot soil profiles with controls. Sampling of dyed preferential flow paths in the sludge plot detected only slight increases in several metals. Preferential flow and metal complexation with soluble organics apparently allow leaching without easily detectable readsorption in the subsoil. The lack of significant metal deposition in subsoil may not be reliable evidence for immobility of sludge-applied metals.     

In situ measurements of concentrations of Cd, Co, Fe and Mn in estuarine porewater using DGT

Vertical profiles of metals were measured by the in situ application of DGT (diffusive gradients in thin films). Well-defined laboratory systems ensured the good reproducibility and precision DGT accumulated metals on a chelex resin after diffusional transport through a layer of hydrogel. Three kinds of DGT probes (with three thicknesses of diffusive gel: 0.40 mm, 0.80 mm and 1.92 mm) measured interfacial concentration and induced flux from solid to solution phase which had intricate variations with depth. The DGT induced flux and interfacial concentration of four metals belonged to “partially sustained” state, indicating a labile equilibrium of metals between solid phase and porewater. The concentration profiles showed the good correlation between Mn and Co and peak concentrations of Mn and Fe between −2.00 cm and −5.25 cm with depth.     

Heavy metal sequential extraction methods--a modification for tropical soils

Sequential extractions of metals can be useful to study metal distributions in various soil fractions. Although several sequential extraction procedures have been suggested in the literature, most were developed for temperate soils and may not be suitable for tropical soils with high contents of Mn and Fe oxides. The objective of this study was to develop a sequential fractionation procedure for Cu and Zn in tropical soils. Extractions were performed on surface (0–20 cm) samples of ten representative soils of Sao Paulo State, Brazil. Chemically reactive Mn forms were satisfactorily assessed by the new modified procedure. Amorphous and crystalline Fe oxides were more selectively extracted in a new two-step extraction. Soil-born Zn and Cu were primarily associated with recalcitrant soil fractions. The proposed procedure provided more detailed information on metal distribution in tropical soils and better characterization of the various components of the soil matrix. The new procedure is expected to be an important tool for predicting the potential effects of environmental changes and land application of metals on the redistribution of chemical forms of metals in tropical soils.     

Heavy metals in agricultural soils from Piedmont,Italy. Distribution,speciation and chemometric data treatment

The distribution and speciation of heavy metals in five agricultural soils of Piedmont Region (north-western Italy) were investigated. Ten metals, namely Al, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Ti and Zn were considered. Analytical determinations were performed by atomic emission or atomic absorption spectroscopy after microwave sample dissolution in acid solution. Total metal concentrations fit in the typical concentration ranges for unpolluted soils, with the exception of cadmium and lead content in some horizons. The effect of sampling depth on concentrations was discussed. Speciation studies were carried out by applying Tessier's procedure, which allows to subdivide the total metal content into five fractions, representing portions bound to different components of the soil. Moreover, the element labilities in two soils were evaluated by extraction with EDTA. Correlations among the variables and/or similarities among the sampling points were identified by principal component analysis and hierarchical cluster analysis.     

Uptake of metals by food plants grown on soils 10 years after biosolids application

Potentially hazardous trace elements such as Cd, Cu, Cr, Ni and Zn are expected to accumulate in biosolids–amended soil and remain in the soil for a long period of time. In this research, uptake of metals by food plants including cabbage, carrot, lettuce and tomato grown on soils 10 years after biosolids application was studied. All the five metals were significantly accumulated in the biosolids-amended soils. The accumulation of metal in soil did not result in significant increase in concentrations of Cu, Cr and Ni in the edible plant tissues. However, the Cd and Zn concentrations of the edible tissues of plants harvested from the biosolids receiving soils were significantly enhanced in comparison with those of the unaffected soils. The plant uptake under Greenfield sandy loam soil was generally higher than those under the Domino clayey loam soil. The metal concentration of edible plant tissue exhibited increasing trends with respect to the concentrations of the ambulated metals. The extents of the increases were plant species dependent. The indigenous soil metals were absorbed by the plants in much higher rates than those of the biosolids–receiving soils. It appeared that the plant uptake of the indigenous soil-borne metal and the added biosolids-borne metals are independent of one another and mathematically are additive.