首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 203 毫秒
1.
催化湿式氧化法处理吡虫啉农药废水   总被引:2,自引:0,他引:2  
自制了Cu/Mn,Cu/Ce,Cu/Ni,Ce/Mn,Ce/Ag等催化剂,经过性能比较,选择催化活性较高且金属溶出量较小的Cu/Ni作催化剂。用催化湿式氧化法处理吡虫啉农药废水,考察了各种因素对处理效果的影响。实验结果表明:在进水pH为6.93、Cu/Ni加入量为4.0g、反应温度为190oC、氧分压为1.6MPa、反应时间为120min的条件下,COD去除率为95%;处理后废水的BOD5/COD从0.093增至0.590,可生化性明显改善。  相似文献   

2.
三维电极法处理印染废水   总被引:12,自引:2,他引:12  
采用三维电极法处理印染废水。考察了反应器槽电压、电解时间、电导率、进水pH等因素对废水处理效果的影响。确定了处理废水的最佳工艺条件:反应器槽电压25~30V、电解时间120~180min、进水pH6.5~7.5。处理后废水色度及cOD的去除率分别达90%、50%以上,废水的BOD5/COD从0.21提高至0.32。但废水去除效果受槽电压、电解停留时间及进水pH的影响较大,且不同电极处的出水COD存在一定差别,废水处理耗电量受原水电导率影响很大。  相似文献   

3.
采用铁屑流化床预处理、负载活性炭催化剂催化氧化和混凝沉淀组合工艺处理有机硅废水。废水经铁屑流化床预处理后Cu^2+的去除率达99.90%,COD去除率达23.9%;负载活性炭催化剂催化氧化的最佳工艺条件:催化剂质量浓度为0.5g/L,H202质量浓度为2400mg/L,不投加FeSO4,反应时间为60min,体系pH为3-4,COD去除率达82%。催化氧化后的废水经混凝沉淀处理,调节pn为8-9,可达标排放。  相似文献   

4.
酸性橙Ⅱ废水催化铁内电解法脱色研究   总被引:5,自引:0,他引:5  
对催化铁内电解法处理酸性橙Ⅱ废水进行了研究,考察了进水pH、搅拌速率、进水酸性橙Ⅱ浓度、铁铜比、支持电解质浓度、进水温度等因素对脱色效果的影响。在最优反应条件下,酸性橙Ⅱ的去除率大于98%,COD的去除率大于76%。催化铁内电解法对酸性橙Ⅱ的去除非常有效,且有较宽的pH适应范围。  相似文献   

5.
用次氯酸钠法处理选矿废水   总被引:2,自引:0,他引:2  
采用次氯酸钠法处理铅锌硫化矿选矿废水,考察了废水初始pH、NaClO加入量及反应时间对选矿废水COD去除率的影响。在废水pH为4、NaClO加入量为100g/L、反应时间为30min的条件下,选矿废水的COD去除率可达到98.3%;当pH为11、反应时间为10min、NaClO加入量为1g/L时,选矿废水的COD去除率为39.4%。  相似文献   

6.
液膜法处理含硝基酚废水试验研究   总被引:3,自引:0,他引:3  
栾金义  李昕  王宜军 《化工环保》2003,23(4):195-199
采用液膜法对含硝基酚废水进行了处理试验研究。对低浓度废水选取了适宜的工艺条件:油相中表面活性剂的质量分数为2%;内水相中NaOH的质量分数为2%;乳液中油相与内水相的质量比为2:1;外水相:pH为2;乳液与外水相的体积比为1:3。在进水总酚质量浓度分别为1050、6700mg/L的条件下,出水总硝基酚的去除率均高达99.9%以上,同时废水中的硝基苯和COD也有较好的去除效果。  相似文献   

7.
超声波-H2O2协同作用处理孔雀绿废水   总被引:2,自引:0,他引:2  
范拴喜  江元汝 《化工环保》2007,27(5):404-408
采用超声波(US)-H2O2协同作用处理含孔雀绿的废水(简称废水);考察了H2O2加入量、US功率、反应温度、反应时间对废水色度、COD去除率的影响,并对US-H2O2体系降解孔雀绿的机理进行了探讨。实验结果表明:在US作用下,H2O2加入量对废水色度、COD去除率的影响较大;废水色度、COD去除率均随US功率和反应时问的增加而提高;在US~H2O2体系中,低温对处理废水有利,高温反而不利;US—H2O2处理废水具有协同作用。在废水量为100mL、pH为7.3、反应温度为40℃、H2O2加入量为10mL、US功率为240W、反应时间60min的条件下对废水进行处理,废水COD、色度去除率分别为97.5%,98.8%。  相似文献   

8.
吴斌  李旭东 《化工环保》2005,25(6):459-461
采用内循环式生物系统处理炼油废水,以内循环式水解酸化反应器、好氧流化床、模块化设计的生物接触氧化池作为生物反应器进行中试试验。在进水COD为1231.0mg/L、温度为45℃、水力停留时间为23.1~52.0h的条件下,COD去除率稳定在83.9%以上;在进水COD为296.9mg/L时,可通过切换至低负荷的模块化工艺使出水水质达标。该系统对一定范围内的水力负荷和有机负荷的冲击均有较好的缓冲能力和灵活处理能力。  相似文献   

9.
活性炭催化臭氧氧化法处理奥里油加工废水   总被引:10,自引:1,他引:9  
曲险峰  郑经堂 《化工环保》2006,26(3):222-225
用活性炭作催化剂,对奥里油脱水加工过程中产生的高浓度有机废水进行催化臭氧氧化处理,研究了活性炭加入量、pH和空气进气流量对COD去除率的影响。结果表明,对于所处理的200mL废水,在活性炭加入量为10g、pH为9、进气流量为0.12m^3/h的最佳反应条件下,反应30min时,COD去除率可从单独臭氧氧化的不到10%提高到60%左右。降解的效率依赖于溶液的pH;初始COD越高,对臭氧的利用率越高。重复使用7次后,活性炭对COD的去除率没有明显改变。  相似文献   

10.
化学沉淀-臭氧氧化法处理焦化废水   总被引:4,自引:4,他引:0  
采用臭氧氧化法对焦化废水(简称废水)进行处理,考察臭氧质量流量和废水pH对废水COD和NH3-N去除率的影响。实验结果表明,在臭氧质量流量为3.6g/h、废水pH为12、反应时间为12h的条件下,废水COD和NH3-N去除率分别为93.74%和74.28%。直接采用臭氧氧化法不能使NH3-N得到较好的去除,采用化学沉淀-臭氧氧化法处理焦化废水后,废水COD、NH3-N、挥发酚和色度的去除率均达97%以上。  相似文献   

11.
Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.  相似文献   

12.
Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.  相似文献   

13.
高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6~9,COD 302mg/L,BOD5 108mg/L,SS30mg/L,色度36倍,水质达到GB8978--1996(污水综合排放标准》三级标准。  相似文献   

14.
Application of Cellulose Microfibrils in Polymer Nanocomposites   总被引:1,自引:0,他引:1  
Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.  相似文献   

15.
Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.  相似文献   

16.
Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.  相似文献   

17.
In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.  相似文献   

18.
The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.  相似文献   

19.
During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH4 + immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH4 + immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH4 + immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO2 productionand net NH4 + immobilization, but not net Nmineralization. The immobilization of 15NH4 +caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized 15NH4 + intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH4 +immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.  相似文献   

20.
Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by 1H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号