焦炭和废铁屑微电解预处理垃圾渗滤液的研究

研究表明,废铁屑和焦炭微电解是预处理垃圾渗滤液的一种有效方法,可去除垃圾渗滤液COD、色度和腐殖酸等污染物质,改善其可生化性、降低负荷,为后续生化处理创造良好的条件.通过静态正交实验确定废铁屑和焦炭最佳投加体积比为1∶3;最佳反应pH值为4;动态实验中,反应时间为1 h时,COD和色度去除率分别高达68%和91%;BOD/COD从0.3提高到0.5左右.     

焦炭和废铁屑微电解预处理垃圾渗滤液的研究

研究表明,废铁屑和焦炭微电解是预处理垃圾渗滤液的一种有效方法,可去除垃圾渗滤液COD、色度和腐殖酸等污染物质,改善其可生化性、降低负荷,为后续生化处理创造良好的条件.通过静态正交实验确定废铁屑和焦炭最佳投加体积比为1∶3;最佳反应pH值为4;动态实验中,反应时间为1 h时,COD和色度去除率分别高达68%和91%;BOD/COD从0.3提高到0.5左右.     

城市污水厂二级处理出水深度处理组合工艺研究

为了研究臭氧-曝气生物滤池二级处理出水深度处理组合工艺的处理效果,采用臭氧-曝气生物滤池(biological aerated filter, BAF)组合工艺对城市污水处理厂二级生化处理出水进行深度处理。结果表明,组合工艺对造成水中色度的主要物质腐植酸和富里酸类有机物和嗅味物质中的二甲基三硫和二甲基异莰醇(MIB)能够进行有效去除。臭氧氧化能够显著提高后续BAF单元对COD_Mn的去除。在进水COD_Mn6~8 mg/L、色度为25~30度、浊度约为8 NTU的条件下,当臭氧投加量为5~6 mg/L、BAF的水力停留时间为1~1.5 h时,出水COD_Mn< 5 mg/L、色度<5度、浊度<1 NTU,出水水质可满足生产工艺对回用水的水质要求。     

黄姜废水的铁炭微电解-混凝预处理研究

研究了高浓度黄姜废水的铁炭微电解-混凝工艺,结果表明,在进水pH 4.0、停留时间为40 min且有曝气条件下,COD去除率达到64.70%,色度去除率为72.22%,废水的BOD/COD值可由0.29提高到0.56,有利于废水的后续生化处理.     

铁炭微电解法预处理超高盐榨菜腌制废水

超高盐榨菜腌制废水是高盐、高氮磷及高有机物废水,目前常采用生物方法进行处理,但因高污染物浓度及高盐度影响,处理效果不够理想;因此,选用铁炭微电解法对超高盐榨菜腌制废水进行预处理。通过静态烧杯实验,研究了反应时间、初始pH、铁炭体积比和铁水体积比对COD和氨氮去除率的影响。单因素实验的最佳处理条件：原水pH4～4．5,反应时间为30min,铁炭体积比为1：1,铁水体积比为2：1,出水COD和氨氮的去除率分别为57．29％和53．11％,盐度由原水的6．62％下降为3．63％,去除率达45．17％,pH由原水4．01升高为6．38。正交实验结果表明,影响COD和氨氮去除率的因素从大到小的顺序为：铁水体积比、初始pH、反应时间、铁炭体积比。实验表明,采用铁炭微电解法能够对超高盐榨菜腌制废水中的COD和氨氮进行有效去除,出水的pH升高和盐度下降,能满足后续生物处理的预处理要求。     

多元微电解填料对煤制油废水预处理的影响

采用高温烧结型微电解填料预处理煤制油废水,通过正交实验研究了初始pH、微电解时间及曝气强度等对废水的预处理影响。结果表明,微电解影响因素从大到小依次为:微电解时间pH曝气强度;微电解预处理煤制油废水的最佳工艺参数为:初始pH 4.0,微电解90 min,气水比3∶1充氧曝气;通过平行实验,COD平均去除率及出水水质分别为54.7%和1 773 mg/L,废水生物毒性指标EC50由原水12.5%的高毒性转化成48.3%的中毒性,为后续生化系统的正常运行提供了有利条件,是预处理煤制油废水的有效方法之一。     

生物-微电解组合工艺处理染料废水研究

采用上流式污泥床过滤器(upflow blanket filter,UBF) 曝气生物滤池(biological aerated filter,BAF) 微电解的组合工艺,对盐度接近2%、色度和COD分别约为8 000倍和600.5 mg/L的染料废水进行处理.经过连续120 d的稳定运行后,组合系统处理效果良好,脱色率和COD去除率分别达到99%和75%以上.UBF和微电解单元均可以大幅度提高废水的可生化性,有利于进一步的生物处理.UV-Vis扫描和GC-MS分析表明,该组合工艺能破坏染料的发色基团和共轭双键,并能高效降解原水中的酚类、氯代有机物和复杂的杂环类化合物.实验结果表明,UBF BAF 微电解的组合工艺是处理染料废水的一种有效方法.     

微电解-絮凝预处理味精发酵废母液实验研究

味精发酵废母液COD浓度极高,为了有效降低后续生物处理单元的负荷,研究采用微电解絮凝方法预处理该废水。实验研究了曝气对废水COD去除率的影响,用正交实验考察了原水和出水pH值、Fe/C和反应温度等因素对COD去除率的影响,实验结果表明,曝气能有效提高COD去除率;在正交实验确定的优化因素组合,即原水pH为2,出水pH值为9,Fe/C为0.5的条件下反应3 h,废水COD平均去除率可达到48.7%。     

UV-Fenton体系预处理四氢呋喃废水实验研究

采用UV-Fenton体系预处理四氢呋喃废水,实验结果表明,pH值、反应时间、Fe2+和H2O2投加量等因素对处理效果有较大的影响。实验确定的最佳反应条件为:原水pH=5,Fe2+投加量2.5 mmol/L,H2O2投加量12 mmol/L,反应时间90 min,连续曝气,在此条件下,COD去除率可达85%左右。经UV-Fenton体系处理后,废水的B/C值由0.16增至0.47,可生化性提高,可满足后续生化处理的要求。     

响应曲面法优化复合絮凝剂的制备工艺

为了提高染料废水中COD和色度的去除效果,采用响应曲面法对聚硅酸类新型复合絮凝剂的制备工艺进行了优化实验研究。在单因素实验基础上采用Box-Behnken Design(BBD)实验设计方法,设计出了影响染料废水处理效果的3因素3水平共15组实验,其中n(Fe+Al):n(Si)的摩尔比为4～6,n(B+Mg):n(Si)的摩尔比为0.3～0.7,熟化时间为1～3 d。根据15组实验结果,以COD去除率和色度去除率为响应值分别建立了二次多项式响应曲面模型。模型优化结果显示,在n(Fe+Al):n(Si)摩尔比为5∶1,n(B+Mg):n(Si)为0.5∶1,熟化时间为2 d的条件下,制备得到的新型复合絮凝剂聚硅酸铝铁硼镁具有最佳的絮凝处理性能和脱色效果,能有效去除染料废水中的COD和色度,其中出水色度接近于0,COD的去除率达到87.65%,模型验证实验进一步验证了本文所建立的响应曲面法在复合絮凝剂制备工艺优化中的有效性。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.