Effect of preparation methods on the performance of CuFe-SSZ-13 catalysts for selective catalytic reduction of NOx with NH3

CuFe-SSZ-13 catalyst showed excellent performance in the selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) for diesel engine exhaust purification. To investigate the effect of preparation methods on NH₃-SCR performance, Fe was loaded into one-pot synthesized Cu-SSZ-13 catalysts through solid-state ion-exchange (SSIE), homogeneous deposition precipitation (HDP) and liquid ion-exchange (IE), respectively. Three CuFe-SSZ-13 catalysts showed similar SO₂ resistance, which was better than that of Cu-SSZ-13. The improvement was attributed to the protection of Fe species. Hydrothermal stability of three CuFe-SSZ-13 catalysts was significantly different, which was attributed to the state of active species caused by different preparation methods. Compared with the other two catalysts, more active species existed inside the zeolite pores of CuFe-SSZ-13_SSIE. During hydrothermal aging, the aggregation of these active species in the pores caused the collapse of catalyst structure, ultimately leading to the deactivation of CuFe-SSZ-13_SSIE. In contrast, Fe species was dispersed better on the surface over CuFe-SSZ-13_IE, enhancing the hydrothermal stability of catalysts. Consequently, Fe loading effectively improved the resistance of SO₂ and H₂O over Cu-SSZ-13. For CuFe-SSZ-13, large amounts of active species located inside the zeolite pores are not beneficial for the hydrothermal stability.     

不同制备方法对Cu-SSZ-13催化性能的影响

为了考察制备方法对Cu-SSZ-13催化剂在氨选择性催化还原NO_x(NH_3-SCR)中催化性能的影响,使用不同的方法和载体,制备出理化性质有明显差异的3种催化剂(Cu_(3.9)-Na_(0.8)-SSZ-13、Cu_(5.1)-H-SSZ-13和Cu_(4.0)-Na_(4.0)-SSZ-13),并考察3种催化剂的水热稳定性和抗硫中毒性能.结果表明,由于具有适宜的Cu负载量,并且Cu物种的稳定性极高,一步合成法制备的Cu_(3.9)-Na_(0.8)-SSZ-13催化剂的水热稳定性优于液相离子交换法制备的两种催化剂.而以H-SSZ-13为载体,液相离子交换法负载Cu物种制备的Cu_(5.1)-H-SSZ-13催化剂具有最优的抗硫中毒能力,这与其较多的酸性位有关.因此,含有较多酸性位并且活性物种稳定性高是制备水热稳定性和抗硫中毒能力较优的Cu-SSZ-13催化剂的关键.     

超声辅助法制备新型FeMOR分子筛催化NOx还原反应性能研究

采用超声辅助浸渍法成功合成了高铁含量的Fe MOR-5%-UL催化剂,并且测试其催化还原NO性能.研究发现在超声辅助条件下浸渍制得的催化剂可以引入更高比例的离子交换位上的孤立的Fe~(3+),这些铁离子具有更强的NO还原活性,因此超声辅助浸渍法制备的催化剂催化性能显著高于传统的离子交换法和浸渍法.其中活性最高的FeMOR-5%-UL催化剂在添加SO_2等多种气氛时,催化活性下降不显著.并且在持续100 h的汽车尾气条件下进行的稳定性实验中,FeMOR-5%-UL的催化活性没有明显下降.FeMOR-5%-UL的优异的催化活性和稳定性非常具有应用前景和研究价值.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

Fe2O3添加对钛基SCR催化剂表面硫酸氢铵分解行为的影响规律

采用共沉淀法合成了TiO_2及TiO_2-Fe_2O_3载体,并对硫酸氢铵与上述载体之间的相互作用及硫酸氢铵的具体分解行为进行了研究.结果表明,催化剂载体表面含硫官能团主要以双齿硫酸盐的形式存在,含氮官能团以铵根离子的形式存在.当硫酸氢铵沉积于催化剂载体表面时,由于硫酸根离子具有较强的电负性,Ti原子及Fe原子处于电子缺失状态.对于TiO_2载体,硫酸根离子主要与Ti原子相连;而对于TiO_2-Fe_2O_3载体,Ti原子及Fe原子均为硫酸根离子主要的附着位点.采用热分析方法及原位红外对硫酸氢铵在TiO_2及TiO_2-Fe_2O_3载体表面的分解行为进行了研究,发现铁氧化物的添加显著促进了硫酸氢铵在低温区间内的分解行为;与铵根离子相比,硫酸根离子具有更高的热稳定性.催化剂稳定性测试结果表明,铁氧化物的添加显著提高了低温抗硫抗水性能,为实现低温SCR技术的工业应用提供了理论基础.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

One-step preparation of a novel graphitic biochar/Cu0/Fe3O4 composite using CO2-ambiance pyrolysis to activate peroxydisulfate for dye degradation

Herein,a one-step co-pyrolysis protocol was adopted for the first time to prepare a novel pyrogenic carbon-Cu⁰/Fe₃O₄ heteroatoms (FCBC) in CO₂ ambiance to discern the roles of each component in PDS activation.During co-pyrolysis,CO₂ catalyzed formation of reducing gases by biomass which facilitated reductive transformation of Fe³⁺ and Cu²⁺ to Cu⁰ and Fe₃O₄,respectively.According to the a...     

Ce3+与Cu2+协同强化芬顿体系氧化苯酚的效能与机制研究

研究了Ce~(3+)与Cu~(2+)协同强化芬顿体系在不同初始条件下对水中苯酚的氧化效能与机制.结果表明,在p H适用范围的宽度和H_2O_2浓度变化方面,Ce~(3+)/Cu~(2+)/Fe~(2+)/H_2O_2体系比传统的芬顿体系更具有优势,该体系在p H=5.0、H_2O_2浓度为2.0mmol·L-1的条件下,仍可以对苯酚保持相对较高的氧化效能;Cu~(2+)可能会借助反应过程中的中间产物(醌类物质)生成Cu+,Cu+催化H_2O_2分解生成·OH,Ce~(3+)可能促进体系内醌类物质的形成,加快Fe~(3+)与Fe~(2+)的循环效能,在一定程度上提高了芬顿体系中H_2O_2分解生成·OH的速率,说明Cu~(2+)与Ce~(3+)对芬顿体系的强化作用具有协同性;自由基终止剂依然可以抑制Ce~(3+)、Cu~(2+)强化的芬顿体系对苯酚的降解,由此说明体系中起到氧化作用的活性物种仍然是羟基自由基(·OH).     

不同SAPO分子筛负载MnOx催化剂的低温NH3-SCR性能研究

以磷酸硅铝分子筛SAPO-5、SAPO~(-1)1和SAPO-34为载体,采用乙醇分散法制备了用于低温氨选择性还原(NH_3-SCR)NO_x的分子筛负载MnO_x催化剂.活性测试结果显示,3种分子筛催化剂均展现出优良的NH_3-SCR活性,但三者在低温区间的SCR活性存在较明显差异,其SCR活性顺序如下:MnO_x/SAPO-34MnO_x/SAPO-5MnO_x/SAPO~(-1)1.借助XRD、N2吸附-脱附、XPS、H2-TPR、NH_3-TPD、NH_3FT-IR等技术对催化剂的表面活性物种及表面酸性等进行表征分析,结果表明,MnO_x主要以无定型状态分散于载体上,负载后载体的比表面积和孔体积均有所下降.XPS和H2-TPR分析证实,不同分子筛载体上MnO_x的表面浓度与氧化态明显不同.NH_3-TPD和NH_3FT-IR分析揭示了催化剂表面均存在Bronsted酸位和Lewis酸位,其中,Lewis酸性位对低温SCR反应起着关键作用.研究表明,催化剂的催化性能会因载体不同而存在差异,高Mn4+表面浓度和丰富的Lewis酸性位对催化剂在低温区间实现优良的催化活性尤为重要.     

MnFe2O4磁性纳米棒非均相Fenton催化降解水中四环素的研究

采用水热合成法成功制备出MnFe₂O₄磁性纳米棒（s-MnFe₂O₄）,并考察了商品化的Fe₃O₄、MnFe₂O₄和合成的s-MnFe₂O₄纳米棒这3种磁性纳米颗粒作为非均相Fenton催化剂降解水中四环素抗生素的性能.同时,采用X射线衍射（XRD）、透射电镜（TEM）、N₂吸附-脱附、振动样品磁强计（VSM）及X射线光电子能谱（XPS）等技术对催化剂的理化性质进行了表征.非均相Fenton催化降解四环素的结果表明,s-MnFe₂O₄具有最高的催化活性,反应180 min,四环素的去除率可以达到87.6%,TOC的去除率达到47.5%.自由基捕获试验证实了羟基自由基（·OH）是非均相Fenton氧化过程中的主要活性物种.s-MnFe₂O₄磁性纳米棒的高催化活性归因于其表面拥有较高含量的Mn³⁺和Fe²⁺物种,它们的存在能加速界面电子的转移效率,从而促进·OH的生成.合成的s-MnFe₂O₄催化剂具有良好的稳定性,循环使用6次,四环素的去除率仅从87.6%降低到80.2%,且氧化过程中活性组分的流失很少.     

Electrolyte effects on aqueous atmospheric oxidation of sulphur dioxide by hydrogen peroxide

The rate of oxidation of sulphur dioxide by hydrogen peroxide in the presence of various supporting electrolytes has been determined by the stopped flow method. In a sodium perchlorate medium (chosen as reference electrolyte) first-order kinetics were observed with respect to HSO₃⁻, H₂O₂ and H⁺. The influence of the ionic strength was investigated and the third-order rate constant was calculated at infinite dilution. The rate constants of the reaction are shown to be far higher when chloride or ammonium ions are added to the solution.The effect of temperature and traces of metals ions (Mn²⁺, Fe²⁺, Fe³, Cu²⁺, Cr³⁺) was studied. The oxidation reaction is virtually insensitive to the effects of Mn²⁺, Fe³⁺, Cu²⁺ and Cr³⁺. Catalytic activity is observed with Fe²⁺.     

磁性高分子复合水凝胶的制备及其对水中铜离子的吸附性能

以海藻酸钠和聚乙烯醇为骨架负载磁性纳米Fe_3O_4颗粒合成了两种磁性高分子复合水凝胶材料:一种是以Ca~(2+)交联制备的磁性海藻酸钙单网络水凝胶(SAPFe),另一种是以海藻酸钙和聚乙烯醇经循环冷冻解冻制成的磁性双网络水凝胶(DAPFe).利用SEM、FTIR、BET对合成的材料进行表征,并研究了SAPFe和DAPFe对Cu~(2+)的吸附性能.结果表明,DAPFe比表面积达89.01 m~2·g~(-1),平均孔径为2.2 nm,DAPFe比SAPFe具有更低的含水率、更高的交联程度、更发达的孔隙结构和更高的比表面积.DAPFe对Cu~(2+)的最大吸附量可达207.01 mg·g~(-1),远大于SAPFe(173.01 mg·g~(-1)).SAPFe和DAPFe对Cu~(2+)的吸附等温线均符合Langmuir模型,吸附动力学符合准二级吸附动力学模型.通过分析SAPFe和DAPFe吸附Cu~(2+)前后官能团的变化,发现磁性高分子复合水凝胶具有丰富的羧基和羟基功能性官能团,并通过与Cu~(2+)产生螯合作用实现去除.     

支化聚乙烯亚胺功能化磁性纳米吸附剂的制备及对Cu2+的吸附研究

为解决水体中重金属Cu²⁺污染,本研究首先采用水热法制备得到超顺磁四氧化三铁纳米粒子,然后使用对Cu²⁺具有强络合作用的含有丰富氨基官能团的支化聚乙烯亚胺接枝到纳米粒子表面,得到Fe₃O₄@BPEI磁性纳米吸附剂。采用红外光谱（FTIR）、X射线粉末衍射（XRD）、透射电子显微镜（TEM）等对其结构、尺寸及形貌进行表征。研究了不同吸附因素对吸附剂吸附Cu²⁺的影响,确定了最佳吸附条件,并通过吸附动力学模型和吸附等温线模型进一步探讨吸附机理。结果表明：支化聚乙烯亚胺成功接枝到四氧化三铁纳米粒子表面。最佳吸附条件为pH=6.0、吸附平衡时间为40 min、吸附剂用量为10 mg。通过实验数据拟合,Fe₃O₄@PEI吸附Cu²⁺的过程符合Langmuir等温吸附方程和拟二级动力学模型,表明吸附过程为化学吸附控制的单分子层覆盖,在303 K时,模型理论饱和吸附量为141.24 mg/g。表明支化聚乙烯亚胺修饰的磁性纳米吸附剂对Cu²⁺具有较强的吸附能力,对水体中Cu²⁺的去除具有一定的应用前景。     

不同硅铝比Fe-ZSM-5催化剂对氧化亚氮催化分解性能的研究

以不同硅铝比的H-ZSM-5分子筛为载体,采用离子交换法和化学气相沉积法制备Fe-ZSM-5催化剂,并用XRD、BET、TEM、UV-vis和NH3-TPD等表征手段对催化剂进行分析,研究催化剂中铁的存在状态.结果表明,分子筛的硅铝比影响铁在分子筛中的分布形态,化学气相沉积法和热离子交换法制得硅铝比为25的Fe-ZSM-5-25分子筛催化剂上均匀地分布着粒径为8 nm左右的纳米氧化铁颗粒,并且Fe-ZSM-5-25分子筛催化剂比Fe-ZSM-5-300更容易形成Fe3+x O y团簇.制得的Fe-ZSM-5分子筛催化剂催化分解氧化亚氮(N2O),结果表明,相同的制备方法,硅铝比小的Fe-ZSM-5-25催化剂对N2O分解活性更好;相同硅铝比的Fe-ZSM-5催化剂,采用化学气相沉积法制得的对N2O分解活性最好.另外,O2的存在对Fe-ZSM-5上N2O催化分解活性有抑制作用,而NO对N2O催化分解活性展示了一定的正效应.最后,经过100 h的连续反应,Fe-ZSM-5催化剂依然能够保持催化活性.     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.     

Fe3O4@SiO2-Chitosan的制备及其对水中Cu2+的吸附效能研究

以SiO_2包覆Fe_3O_4,戊二醛为交联剂,交联壳聚糖(Chitosan, CTS),制得Fe_3O_4@SiO_2-Chitosan复合磁性纳米粒子.以Fe_3O_4和Fe_3O_4@SiO_2为对照,采用X射线衍射、透射电镜和傅立叶红外光谱对其进行表征分析,并测定了投加量、pH值、吸附时间和温度等因素对Cu~(2+)吸附效果的影响,从动力学、热力学以及再生回用性能评价等方面对其吸附性能进行了探究.结果表明Fe_3O_4@SiO_2-Chitosan对Cu~(2+)的吸附过程符合准二级吸附动力学模型和Langmuir模型,为自发、放热、优惠型的单分子层化学吸附.在pH为6.0, 298 K下达到最大吸附量154.8 mg·g~(-1),吸附解吸4次后吸附容量变化不大,说明Fe_3O_4@SiO_2-Chitosan具有较高的吸附容量,可作为处理含铜废水和回收铜的高效吸附剂.     

Mercury removal from coal combustion flue gas by modified fly ash

Fly ash is a potential alternative to activated carbon for mercury adsorption. The effects of physicochemical properties on the mercury adsorption performance of three fly ash samples were investigated. X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, and other methods were used to characterize the samples. Results indicate that mercury adsorption on fly ash is primarily physisorption and chemisorption. High specific surface areas and small pore diameters are beneficial to efficient mercury removal. Incompletely burned carbon is also an important factor for the improvement of mercury removal efficiency, in particular. The C-M bond, which is formed by the reaction of C and Ti, Si and other elements, may improve mercury oxidation. The samples modified with CuBr2 , CuCl 2 and FeCl3 showed excellent performance for Hg removal, because the chlorine in metal chlorides acts as an oxidant that promotes the conversion of elemental mercury (Hg0) into its oxidized form (Hg2+). Cu2+ and Fe3+ can also promote Hg 0 oxidation as catalysts. HCl and O2 promote the adsorption of Hg by modified fly ash, whereas SO2 inhibits the Hg adsorption because of competitive adsorption for active sites. Fly ash samples modified with CuBr2 , CuCl2 and FeCl3 are therefore promising materials for controlling mercury emissions.     

残留药剂对土壤As、Hg、Cd、Pb浸出测试干扰及消除方法

固化/稳定化是应用最广泛的重金属污染土壤修复技术,但残留药剂在浸出测试过程对土壤二次修复导致的验收假达标风险未引起充分重视.本研究分别采用Fe₂（SO₄）₃、Na₂S和KH₂PO₄修复As、Hg、Cd-Pb污染土壤,探究不同养护反应时间、药剂混合均匀度和投加量等工艺条件下土壤重金属浸出浓度差异,验证液相二次修复干扰效应的发生,并考察Cu²⁺和Al³⁺等竞争剂对土壤残留KH₂PO₄药剂干扰的消除效果,提出最佳的残留药剂消除方法.结果表明,分别投加6.7%的Fe₂（SO₄）₃、6.7%的Na₂S和3.3%的KH₂PO₄修复含As、Cd和Pb土壤时,土壤中各重金属浸出浓度从第0 d起分别持续小于0.05、0.5和1.6 mg·L^-1,稳定化效率分别保持在99%、83%~99%和97%~98%.投加0.0008%的Na₂S修复土壤Hg时,Hg浸出浓度自第0 d起随养护反应时间显著下降,稳定化效率维持在78%~88%.虽然修复后土壤中Hg浸出浓度随药剂混合均匀度增加而显著下降,As、Cd、Pb浸出浓度在混合均匀度为67%和33%时相较混合均匀度为100%时均无显著变化（1.7% Fe₂（SO₄）₃修复组除外）,但均小于无二次反应理论值.此外,Cu²⁺能与Pb²⁺竞争浸出液中的残留PO₄^3-减弱干扰效应,当Cu²⁺优化投加量为5.7%、11.3%、14.2%时,混合均匀度67%处理组Pb浸出浓度分别升至理论值的51%、72%、84%,混合均匀度33%处理组Pb浸出浓度则分别升至理论值的38%、71%、81%.而Al³⁺无法与Pb²⁺竞争PO₄^3-,甚至对土壤Pb具有显著活化效果.Cu²⁺对Pb也具有一定的活化效果,因此,需控制Cu²⁺投加量以寻求活化效果与优化作用的最佳平衡点.     

Enhanced catalytic complete oxidation of 1,2-dichloroethane over mesoporous transition metal-doped γ-Al2O3

High-surface-area mesoprous powders of γ-Al₂O₃ doped with Cu^2 +, Cr^3 +, and V^3 + ions were prepared via a modified sol–gel method and were investigated as catalysts for the oxidation of chlorinated organic compounds. The composites retained high surface areas and pore volumes comparable with those of undoped γ-Al₂O₃ and the presence of the transition metal ions enhanced their surface acidic properties. The catalytic activity of the prepared catalysts in the oxidation of 1,2-dichloroethane (DCE) was studied in the temperature range of 250–400°C. The catalytic activity and product selectivity were strongly dependent on the presence and the type of dopant ion. While Cu^2 +- and Cr^3 +-containing catalysts showed 100% conversion at 300°C and 350°C, V^3 +-containing catalyst showed considerably lower conversion. Furthermore, while the major products of the reactions over γ-alumina were vinyl chloride (C₂H₃Cl) and hydrogen chloride (HCl) at all temperatures, Cu- and Cr-doped catalysts showed significantly stronger capability for deep oxidation to CO₂.     

光催化氧化法处理染料中间体H酸水溶液

为了去除水中难氧化的有害染料中间体Ｈ酸,研究以ＴＩＯ２、ＺｎＯ、ＣｄＳ和Ｆｅ２Ｏ３为催化剂,采用低压汞灯为光源,对Ｈ酸水溶液进行光催化氧化实验．结果表明：ＴｉＯ２和ＣｄＳ的催化效果最好．采用ＴｉＯ２作催化剂,光催化氧化５ｈ后,Ｈ酸分解率可达９０％,反应速率遵从Ｌａｎｇｍｕｉｒ－Ｈｉｎｓｈｅｌｗｏｏｄ方程,Ｋ＝１２．３Ｌ／ｍｍｏｌ,ｋ＝２５．２×１０－６ｍｏｌ／ｈ．溶液中投加１０ｍｇ／Ｌ的Ｆｅ３＋或Ａｇ＋,可使反应时间缩短２—３ｈ．研究探讨了ｐＨ、ＴｉＯ２投加量和Ｈ酸浓度对催化氧化过程的影响．