Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and Zn in a freshwater sediment following a collaboratively tested and optimised three-step sequential extraction procedure

Sequential extraction procedures have been used during the last decades to study and determine trace element mobility in aquatic sediments. However, the results obtained are operationally defined and, therefore, the significance of the analytical results is related to the extraction scheme used. So, there is a need for suitable reference materials for this type of study to enable the validation of the methodologies and to control the quality of the measurements. This paper describes the preparation of a sediment reference material, BCR-701, the homogeneity and stability studies and the analytical work performed for the certification of the extractable contents of some trace elements, following a collaboratively tested and optimised sequential (three-step) extraction procedure. The paper contains all the results and gives the methods used to certify the extractable contents (mass fractions expressed as mg kg-1 on a dry matter basis) of Cd, Cr, Cu, Ni, Pb and Zn in all steps. Moreover, indicative values are given for the aqua regia extractable contents of the six elements in the sediment and the residue obtained after sequential extraction.     

A survey of Pb,Cu, Zn,Cd, Cr,As, and Se in earthworms and soil from diverse sites

Earthworms and soils were collected from 20 diverse sites in Maryland, Pennsylvania, and Virginia, and were analyzed for Pb, Cu, Zn, Cd, Cr, As, and Se. Correlation coefficients relating concentrations of the elements in earthworms to concentrations in soil were low (–0.20<r<+0.57). Species differences and ecological variables contributed to the variability in concentrations of these elements in earthworms. The maximum concentrations of Pb (2100 ppm), Zn (1600 ppm), Cd (23 ppm) and Se (7.6 ppm) detected in earthworms were in the range reported to be toxic to animals fed diets containing these elements; however, even in the absence of any environmental contamination, some species of earthworms may contain high concentrations of Pb, Zn, and Se. Earthworms of the genus Eisenoides, for example, were exceptional in their ability to concentrate Pb. When earthworms are used as indicators of environmental contamination, it is important to identify the species, to report the soil characteristics, and to collect similar earthworms from very similar but uncontaminated soil.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).     

Competitive sorption of Cd, Cu, Mn, Ni, Pb and Zn in polluted and unpolluted calcareous soils

The objectives of this study were to investigate competitive sorption behaviour of heavy metals (Cd, Cu, Mn, Ni, Pb and Zn) under different management practices and identify soil characteristics that can be correlated with the retention and mobility of heavy metals using 65 calcareous soil samples. The lowest sorption was found for Mn and Ni in competition with the other metals, indicating the high mobility of these two cations. The Freundlich equation adequately described heavy metals adsorption. On the basis of Freundlich distribution coefficient, the selectivity sequence of the metal adsorption was Cu?>?Pb?>?Cd?>?Zn?>?Ni?>?Mn. The mean value of the joint distribution coefficient (K _dΣsp) was 182.1, 364.1, 414.7, 250.1, 277.7, 459.9 and 344.8 l kg^?1 for garden, garlic, pasture, potato, vegetables, wheat and polluted soils, respectively. The lowest observed K _dΣsp in garden soil samples was due to the lower cation exchange capacity and lower carbonate content. The results of the geochemical modelling under low and high metal addition indicated that Cd, Ni, Mn and Zn were mainly retained via adsorption, while Pb and Cu were retained via adsorption and precipitation. Stepwise forward regression analysis showed that clay, organic matter and CaCO₃ were the most important soil properties influencing competitive adsorption of Cd, Mn, Ni and Zn. The results in this study point to a relatively easy way to estimate distribution coefficient values.     

Accumulation of Cu, Cd, Cr, Mn and Pb from artificially contaminated soil by Bacopa Monnieri

The metal accumulation potential of Bacopa monnieri L. was assessed under simulated laboratory conditions. This study was carried out in mixed metals (Cu, Cd, Pb, Cr, Mn) condition and repeated exposures in artificial contaminated soil. The growing shoots were planted in garden subsoil containing 3, 16, 32, 64, 160 M each of the above metals. After 8 weeks, plants were refeeded to three times higher concentrations of each metal than initially used to assess the maximum accumulating potential of the metals. The accumulation of the metals by the root and shoot was concentration and duration dependent. The metal accumulation was considerably higher in the fine root than in the shoot and showed the following order : Mn > Cr > Cu > Cd > Pb. The plants showed high tolerance to the metals as no visible phytotoxic symptom was produced after 8 weeks. However, as a result of combined metal toxicity, chlorophyll content was reduced by 62% after 12 weeks. The highest metal concentration was lethal to the plant at 16 weeks. In view of their high tolerance, the plants of B. monnieri may be considered for the amelioration of industrially-polluted wetlands experiencing regular flushing of wastewaters.     

Assessment of the effects of Cr, Cu, Ni and Pb soil contamination by ecotoxicological tests

This study aimed to assess soil quality by chemical and ecotoxicological investigations and to check the correspondence between soil metal concentrations and ecotoxicity. For these purposes, surface soils collected at four adjacent roadside urban parks and at a former industrial area were characterized for C/N, organic matter content, texture, and pH. Cr, Cu, Ni and Pb, chosen among the most representative soil metal contaminants, were measured as total content and as available and water soluble fractions. In addition, the total concentrations of the investigated metals were used to calculate two chemical indices: the contamination and the potential ecological risk factors. The toxicity of the investigated soils was evaluated by an ecotoxicity test battery carried out on both soil samples (Vibrio fischeri, Heterocypris incongruens and Sinapis alba) and elutriates (Vibrio fischeri, Daphnia magna and Selenastrum capricornutum). The findings, both by the chemical and ecotoxicological approaches, would suggest that the soils with high metal contamination pose ecological risks. On the other hand, moderately metal contaminated soils did not exclude soil ecotoxicity. In fact, toxic effects were also highlighted in soils with low metal content, toxicity being affected by metal availability and soil characteristics. Moreover, the results suggest the importance of using a battery of tests to assess soil ecotoxicity.     

Solid phase extraction of Cd,Pb, Ni,Cu, and Zn in environmental samples on multiwalled carbon nanotubes

A simple and sensitive solid phase extraction (SPE) method on multiwalled carbon nanotubes (MWCNTs) is presented for the determination of cadmium, lead, nickel, copper, and zinc at trace levels combined with flame atomic absorption spectrometry. The effects of parameters like pH, sample volume, sample and eluent flow rates, eluent concentration, and volume and type of eluent on the recovery of trace elements was examined. The metals retained on the nanotube at pH 6.5 as α-benzoin oxime complexes were eluted by 10 mL 2 M HNO₃ in acetone. The influence of matrix ions on the developed method was also evaluated. The preconcentration factor of the method was found to be 50. The detection limits for Cd(II), Pb(II), Ni(II), Cu(II), and Zn(II) were found as 1.7, 5.5, 6.0, 2.3, and 2.4 μg L^?1, respectively. To test the accuracy of the method, the method was applied to TMDA-70 fortified lake water and Spinach 1570A standard reference materials. Addition recovery studies were applied to tap water and cracked wheat samples, and determination of the analyte elements was carried out in some food samples with good results.     

Determination of Cu, Pb, Zn, Ni, Co, Cd, and Mn in road dusts of Samsun City

The dust samples from 52 different locations in central roads of Samsun City were collected in a study area of 40 km long for the purpose of determining total metal concentrations of dust samples by flame atomic absorption spectrometry. The concentrations of Cu, Pb, Co, Zn, Ni, Mn, and Cd were found in the ranges of 11.92–352.43, 5.47–223.57, 4.52–41.69, 40.85–173.10, 18.71–131.29, 133.19–179.13, and 0.02–6.16 mg/kg, respectively. The results showed that metal levels were higher around the industrial area than other locations. Principal component analysis was also carried out to ascertain the possible contributing factors towards the metal concentrations. Validation of the analytical results was tested by analysis of the BCR 032 Moroccan phosphate rock certified reference material.     

Environmentally safe sewage sludge disposal: the impact of liming on the behaviour of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn

Dewatered sewage sludge containing relatively high total concentrations of Cr (945 micrograms ml-1), Cu (523 micrograms ml-1), Ni (1186 micrograms ml-1) and Zn (2950 micrograms ml-1) was treated with quicklime and sawdust for sludge disinfection and post-stabilisation. The mobility of the heavy metals in the sludge samples was assessed by applying a modified five-step Tessier sequential extraction procedure. Water was added as a first step for estimation of the proportion of the easily soluble metal fractions. To check the precision of the analytical work the concentrations of heavy metals in steps 1-6 of the extraction procedure were summed and compared to the total metal concentrations. The mass balance agreed within +/- 3% for Cd, Cu, Cr, and Zn and within +/- 5% for Ni, Pb, Fe and Mn. Data from the partitioning study indicate that in the lime-treated sludge at a pH of 12 the mobility of Cu and Ni notably increased with the solubilisation of these metals from their organic and/or carbonate and Fe and Mn oxide and hydroxide fractions, respectively. Liming slightly decreased the proportion of other heavy metals in the easily soluble fractions while its impact on the partitioning between other sludge phases was almost insignificant. Due to the increased solubility of Ni and Cu as well as potential Cr oxidation at high pH, liming cannot be recommended for sludge disinfection. Addition of sawdust did not change the heavy metal partitioning.     

Determination of heavy metals (Cd, Cr, Cu, Fe, Ni, Pb, Zn) by ICP-OES and their speciation in Algerian Mediterranean Sea sediments after a five-stage sequential extraction procedure

Surface sediment samples (n = 18) were collected from the Algerian Mediterranean coasts and analyzed for seven metals using inductively coupled plasma-optical emission spectrometry in order to asses the distribution and bioavailability of metals and to study the anthropogenic factors affecting their concentrations. Sediment samples were size-fractionated into three sizes: 1,080–500 (coarse), 500–250 (medium), and <250 mm (fine). Bulk sediments were subjected to both sequential extraction and total digestion to evaluate the reliability of the sequential extraction procedure (SEP), while the fractions have been only sequentially extracted for metals speciation. The metals were sequentially extracted into five phases namely exchangeable (P1), carbonates (P2), Fe–Mn oxides (P3), organic (P4) and residual (P5). Metal recoveries in sequential extractions were ±20% of the independently measured total metal concentrations; the high recovery rates indicate the good reliability of the SEP used in this study. Correlation coefficients indicated that the grain size has an effect on the distribution of metals in the investigated samples. The order of metal levels in the fractions was medium > fine > coarse for all the metals. The average total extractable metal concentrations for Cd, Cr, Cu, Fe, Ni, Pb, and Zn were 1.1, 8.8, 4.7, 1,291.3, 13.9, 5.7 and 20.4 μg/g, respectively. The northeastern shelf had the lowest metal levels while the highest were in northwestern part mainly due to the significant tourism activities in the northwestern part. Comparison of our results to Earth’s crust values and to previous studies points out that our samples were relatively unpolluted with respect to the heavy metals investigated; most of the metals are not from anthropogenic sources. Enrichment factors as the criteria for examining the impact of the anthropogenic sources of heavy metals were calculated, and it was observed that the investigated samples were not contaminated with Cr, Cu, and Fe, moderately contaminated with Ni, Pb, and Cd, and contaminated with Cd in some sites. The P5 phase had the highest percents of Cr, Cu, Fe, Ni, and Zn. Cadmium and lead were predominant in the P4 phase, while Cu, Fe and Zn were distributed in the order P5 > P3 > P4 > P2 > P1. The following order of bioavailability was found with the heavy metals Pb > Cr > Cd > Ni > Zn > Cu > Fe.     

Evaluation of Pb, Cu, Zn, Cd, Ni and Fe levels in Rosmarinus officinalis labaiatae (Rosemary) medicinal plant and soils in selected zones in Jordan

The concentration of heavy metals including Pb, Cu, Zn, Cd, Ni and Fe in different parts of Rosmarinus officinalis medicinal plant grown in Jordan were evaluated. Medicinal plant samples and soil samples were collected from three different zones in Jordan (Irbid, Al-Mafraq and Ma’an). Samples were analyzed by atomic absorption spectrometry (AAS) after chemical treatments using acid digestion procedures. Heavy metal levels in washed and unwashed in each part of R. officinalis were analyzed and compared statistically. Results show that concentrations of investigated heavy metals were varied from plant part to another part of R. officinalis. For example, Pb, Zn, Cu and Cd in most parts of R. officinalis in the three zones were concentrated in the following order: flowers, leaves, stems, whereas Pb, Ni and Fe were concentrated in order as follows: leaves, flowers and stems. Heavy metal concentrations in soil samples was evaluated and correlated with their levels in R. officinalis. Two standard reference materials of plant (SRM 1790a; spinach leaves and CRM 281; rye grass) and one standard reference materials of soil (GBW 07406) were examined to validate the method used. Results show that high recoveries were obtained.     

Application of a modified BCR sequential extraction (three-step) procedure for the determination of extractable trace metal contents in a sewage sludge amended soil reference material (CRM 483), complemented by a three-year stability study of acetic acid and EDTA extractable metal content

This paper provides additional data on a sewage sludge amended soil certified reference material, CRM 483, which was certified in 1997 for its EDTA and acetic acid extractable contents of some trace metals, following standardised extraction procedures. The additional work aimed to test the long-term stability of the material and the applicability of an improved version of the BCR three-step sequential extraction procedure on the sewage sludge amended soil (CRM 483). The paper demonstrates the CRM 483 long-term stability for EDTA and acetic acid extractable contents of Cd, Cr, Cu, Ni, Pb and Zn and gives the results (obtained in the framework of an interlaboratory study) for the extractable contents of the same elements in the CRM 483, following the BCR three-step sequential extraction scheme. The aqua regia extractable contents following the ISO 11466 Standard are also given. The data are given as indicative (not certified) values.     

Chemical speciation and partitioning of trace metals (Cd, Co, Cu, Ni, Pb) in the lower Athabasca river and its tributaries (Alberta, Canada)

Concentrations of Cd, Co, Cu, Ni and Pb were measured in particulate and dissolved phases at 11 sites located upstream and near Athabasca oil sands development. The in situ discrimination between non-labile and labile dissolved metals was done using diffusive gradients in thin-films (DGT) devices. The DGT-labile fraction of Co and Ni was 30% lower near development sites whereas Cu, Cd and Pb showed minor changes spatially. It was found that an 8-fold increase in dissolved organic matter (DOM) near development induced a rapid decrease in DGT-labile metals. Dissolved metal concentrations were used along with DOM, major ions, nutrients, pH and conductivity to calculate the distribution of dissolved metal species using the speciation model WHAM. Labile-DGT metal concentrations agreed well with WHAM-predicted concentrations. It was also found that a significant amount of metals were associated with the non-DGT labile fraction (i.e. colloidal DOM) and colloid abundance was more important than suspended particulate matter abundance in influencing metal mobility near Athabasca oil soils development. Since changes in colloidal DOM levels are likely to be the result of surface mining activities, this confirms the serious effects of oil sands activities on metal biogeochemical cycles in the lower Athabasca River.     

Cd,Cr, Cu,Pb, and Zn concentrations in <Emphasis Type="Italic">Ulva lactuca,Codium fragile,Jania rubens,</Emphasis> and <Emphasis Type="Italic">Dictyota dichotoma</Emphasis> from Rabta Bay,Jijel (Algeria)

Concentrations of Cd, Cr, Cu, Pb, and Zn were determined in algae samples collected from the Rabta Bay in the Mediterranean Sea, Algeria. The levels of heavy metals in the macroalgae, Ulva lactuca, Codium fragile (green algae), Jania rubens (red algae), and Dictyota dichotoma (brown algae) recorded high concentrations except for Cd. Moreover, Zn was the most predominant metal in the seaweeds. The obtained HM contents indicate that different species demonstrate various degree of metal accumulation and the obtained higher values in site 1 of the studied zone can be attributed to the discharge influence of two rivers (Mouttas and Larayeche Rivers), entering the Mediterranean Sea and local pollutant emissions. The abundance of heavy metal concentrations in the macroalgae samples was found in the order below: Zn > Cu > Pb > Cr > Cd from the studied zone. The highest amounts of heavy metals in algae samples were Cd, Cu, and Pb in brown algae, and Cr and Zn in green and brown algae from the studied zone (Rabta Bay).     

Assessment of heavy metals (Cd and Pb) and micronutrients (Cu, Mn, and Zn) of paddy (Oryza sativa L.) field surface soil and water in a predominantly paddy-cultivated area at Puducherry (Pondicherry, India), and effects of the agricultural runoff on the elemental concentrations of a receiving rivulet

The concentrations of toxic heavy metals—Cd and Pb and micronutrients—Cu, Mn, and Zn were assessed in the surface soil and water of three different stages of paddy (Oryza sativa L.) fields, the stage I—the first stage in the field soon after transplantation of the paddy seedlings, holding adequate amount of water on soil surface, stage II—the middle stage with paddy plants of stem of about 40 cm length, with sufficient amount of water on the soil surface, and stage III—the final stage with fully grown rice plants and very little amount of water in the field at Bahour, a predominantly paddy cultivating area in Puducherry located on the southeast Coast of India. Comparison of the heavy metal and micronutrient concentrations of the soil and water across the three stages of paddy field showed their concentrations were significantly higher in soil compared with that of water (p?<?0.05) of the fields probably because of accumulation and adsorption in soil. The elemental concentrations in paddy soil as well as water was in the ranking order of Cd?>?Mn?>?Zn?>?Cu?>?Pb indicating concentration of Cd was maximum and Pb was minimum. The elemental concentrations in both soil and water across the three stages showed a ranking order of stage II?>?stage III?>?stage I. The runoff from the paddy fields has affected the elemental concentrations of the water and sediment of an adjacent receiving rivulet.