Bacterial inactivation,DNA damage,and faster ATP degradation induced by ultraviolet disinfection

• Long amplicon is more effective to test DNA damage induced by UV. • ATP in bacteria does not degrade instantly but does eventually after UV exposure. • After medium pressure UV exposure, ATP degraded faster. The efficacy of ultraviolet (UV) disinfection has been validated in numerous studies by using culture-based methods. However, the discovery of viable but non-culturable bacteria has necessitated the investigation of UV disinfection based on bacterial viability parameters. We used quantitative polymerase chain reaction (qPCR) to investigate DNA damage and evaluated adenosine triphosphate (ATP) to indicate bacterial viability. The results of qPCR effectively showed the DNA damage induced by UV when using longer gene amplicons, in that sufficiently long amplicons of both 16S and gadA indicated that the UV induced DNA damages. The copy concentrations of the long amplicons of 16S and gadA decreased by 2.38 log/mL and 1.88 log/mL, respectively, after exposure to 40 mJ/cm² low-pressure UV. After UV exposure, the ATP level in the bacteria did not decrease instantly. Instead it decreased gradually at a rate that was positively related to the UV fluence. For low-pressure UV, this rate of decrease was slow, but for medium pressure UV, this rate of decrease was relatively high when the UV fluence reached 40 mJ/cm². At the same UV fluence, the ATP level in the bacteria decreased at a faster rate after exposure to medium-pressure UV.     

Photolysis and photooxidation of typical gaseous VOCs by UV Irradiation: Removal performance and mechanisms

UV photodegradation of 27 typical VOCs was systematically investigated. Contribution of photolysis and photooxidation to VOCs removal was identified. Gaseous VOC could be partially converted to particles by 185/254 nm UV irradiation. The mineralization and conversion of 27 VOCs by UV irradiation were reported. Photodegradation by ultraviolet irradiation (UV) is increasingly applied in volatile organic compound (VOC) and odor gas treatments. In this study, 27 typical VOCs, including 11 hydrocarbons and 16 hydrocarbon derivatives, at 150–200 ppm in air and nitrogen gas were treated by a laboratory-scale UV reactor with 185/254 nm irradiation to systematically investigate their removal and conversion by UV irradiation. For the tested 27 VOCs, the VOC removal efficiencies in air were within the range of 13%–97% (with an average of 80%) at a retention time of 53 s, which showed a moderate positive correlation with the molecular weight of the VOCs (R = 0.53). The respective contributions of photolysis and photooxidation to VOC removal were identified for each VOC. According to the CO₂ results, the mineralization rate of the tested VOCs was within the range of 9%–90%, with an average of 41% and were negatively correlated to the molecular weight (R = -0.63). Many of the tested VOCs exhibited high concentration particulate matters in the off-gases with a 3–283 mg/m³ PM₁₀ range and a 2–40 mg/m³ PM_2.5 range. The carbon balance of each VOC during UV irradiation was analyzed based on the VOC, CO₂ and PM₁₀ concentrations. Certain organic intermediates and 23–218 ppm ozone were also identified in the off-gases. Although the UV technique exhibited a high VOC removal efficiency, its drawbacks, specifically low mineralization, particulate matters production, and ozone emission, must be considered prior to its application in VOC gas treatments.     

Influence of reclaimed water discharge on the dissemination and relationships of sulfonamide,sulfonamide resistance genes along the Chaobai River,Beijing

Reclaimed water threatens the ecological safety of the Chaobai River. SMX, TMP, and SDZ were the first three abundant antibiotics in the research area. SRGs and intI1 were widespread with high abundance after reclaimed water recharge. The SRGs values followed the sequence: Summer>autumn>spring>winter. Strong correlations were detected between SRGs and environmental factors. Reclaimed water represents an important source of antibiotics and antibiotic resistance genes, threatening the ecological safety of receiving environments, while alleviating water resource shortages. This study investigated the dissemination of sulfonamide (SAs), sulfonamide resistance genes (SRGs), and class one integrons (intI1) in the surface water of the recharging area of the Chaobai River. The three antibiotics sulfamethoxazole, trimethoprim, and sulfadiazine had the highest abundance. The highest absolute abundances were 2.91×10⁶, 6.94×10⁶, and 2.18×10⁴ copies/mL for sul1, sul2, and intI1 at the recharge point, respectively. SRGs and intI1 were widespread and had high abundance not only at the recharging point, but also in remote areas up to 8 km away. Seasonal variations of SRGs abundance followed the order of summer>autumn>spring>winter. Significant correlations were found between SRGs and intI1 (R² = 0.887 and 0.786, p<0.01), indicating the potential risk of SRGs dissemination. Strong correlations between the abundance of SRGs and environmental factors were also found, suggesting that appropriate environmental conditions favor the spread of SRGs. The obtained results indicate that recharging with reclaimed water causes dissemination and enrichment of SAs and SRGs in the receiving river. Further research is required for the risk assessment and scientific management of reclaimed water.     

Elimination of antibiotic resistance genes and control of horizontal transfer risk by UV-based treatment of drinking water: A mini review

Antibiotic-resistant bacteria and antibiotic resistance genes are in water bodies. UV/chlorination method is better to remove ARGs than UV or chlorination alone. Research on UV/hydrogen peroxide to eliminate ARGs is forthcoming. UV-based photocatalytic processes are effective to degrade ARGs. Antibiotic-resistant bacteria (ARB) and antibiotic resistance genes (ARGs) have been recognized as one of the biggest public health issues of the 21st century. Both ARB and ARGs have been determined in water after treatment with conventional disinfectants. Ultraviolet (UV) technology has been seen growth in application to disinfect the water. However, UV method alone is not adequate to degrade ARGs in water. Researchers are investigating the combination of UV with other oxidants (chlorine, hydrogen peroxide (H₂O₂), peroxymonosulfate (PMS), and photocatalysts) to harness the high reactivity of produced reactive species (Clž·, ClOž·ž, Clž₂·ž⁻, žž·OH, and SOž₄ž·⁻€) in such processes with constituents of cell (e.g., deoxyribonucleic acid (DNA) and its components) in order to increase the degradation efficiency of ARGs. This paper briefly reviews the current status of different UV-based treatments (UV/chlorination, UV/H₂O₂, UV/PMS, and UV-photocatalysis) to degrade ARGs and to control horizontal gene transfer (HGT) in water. The review also provides discussion on the mechanism of degradation of ARGs and application of q-PCR and gel electrophoresis to obtain insights of the fate of ARGs during UV-based treatment processes.     

Evaluation of the technoeconomic feasibility of electrochemical hydrogen peroxide production for decentralized water treatment

• Gas diffusion electrode (GDE) is a suitable setup for practical water treatment. • Electrochemical H₂O₂ production is an economically competitive technology. • High current efficiency of H₂O₂ production was obtained with GDE at 5–400 mA/cm². • GDE maintained high stability for H₂O₂ production for ~1000 h. • Electro-generation of H₂O₂ enhances ibuprofen removal in an E-peroxone process. This study evaluated the feasibility of electrochemical hydrogen peroxide (H₂O₂) production with gas diffusion electrode (GDE) for decentralized water treatment. Carbon black-polytetrafluoroethylene GDEs were prepared and tested in a continuous flow electrochemical cell for H₂O₂ production from oxygen reduction. Results showed that because of the effective oxygen transfer in GDEs, the electrode maintained high apparent current efficiencies (ACEs,>80%) for H₂O₂ production over a wide current density range of 5–400 mA/cm², and H₂O₂ production rates as high as ~202 mg/h/cm² could be obtained. Long-term stability test showed that the GDE maintained high ACEs (>85%) and low energy consumption (<10 kWh/kg H₂O₂) for H₂O₂ production for 42 d (~1000 h). However, the ACEs then decreased to ~70% in the following 4 days because water flooding of GDE pores considerably impeded oxygen transport at the late stage of the trial. Based on an electrode lifetime of 46 days, the overall cost for H₂O₂ production was estimated to be ~0.88 $/kg H₂O₂, including an electricity cost of 0.61 $/kg and an electrode capital cost of 0.27 $/kg. With a 9 cm² GDE and 40 mA/cm² current density, ~2–4 mg/L of H₂O₂ could be produced on site for the electro-peroxone treatment of a 1.2 m³/d groundwater flow, which considerably enhanced ibuprofen abatement compared with ozonation alone (~43%–59% vs. 7%). These findings suggest that electrochemical H₂O₂ production with GDEs holds great promise for the development of compact treatment technologies for decentralized water treatment at a household and community level.     

Enhanced activation of peroxymonosulfate by CNT-TiO2 under UV-light assistance for efficient degradation of organic pollutants

CNT-TiO₂ composite is used to activate PMS under UV-light assistance. Superior performance is due to the enhanced electron-transfer ability of CNT. SO₄•⁻, •OH and ¹O₂ play key roles in the degradation of organic pollutants. In this work, a UV-light assisted peroxymonosulfate (PMS) activation system was constructed with the composite catalyst of multi-walled carbon nanotubes (CNT) - titanium dioxide (TiO₂). Under the UV light irradiation, the photoinduced electrons generated from TiO₂ could be continuously transferred to CNT for the activation of PMS to improve the catalytic performance of organic pollutant degradation. Meanwhile, the separation of photoinduced electron-hole pairs could enhance the photocatalysis efficiency. The electron spin resonance spectroscopy (EPR) and quenching experiments confirmed the generation of sulfate radical (SO₄•⁻), hydroxyl radical (•OH) and singlet oxygen (¹O₂) in the UV/PMS/20%CNT-TiO₂ system. Almost 100% phenol degradation was observed within 20 min UV-light irradiation. The kinetic reaction rate constant of the UV/PMS/20%CNT-TiO₂ system (0.18 min⁻¹) was 23.7 times higher than that of the PMS/Co₃O₄ system (0.0076 min⁻¹). This higher catalytic performance was ascribed to the introduction of photoinduced electrons, which could enhance the activation of PMS by the transfer of electrons in the UV/PMS/CNT-TiO₂ system.     

Fungal diversity and its mechanism of community shaping in the milieu of sanitary landfill

• Ascomycota was the predominant phylum in sanitary landfill fungal communities. • Saprophytic fungi may be of special importance in landfill ecology. • Both richness and diversity of fungal community were lower in leachate than refuse. • Physical habitat partly contributed to the geographic variance of fungal community. • NO₃⁻ was considered the most significant abiotic factor shaping fungal community. Land filling is the main method to dispose municipal solid waste in China. During the decomposition of organic waste in landfills, fungi play an important role in organic carbon degradation and nitrogen cycling. However, fungal composition and potential functions in landfill have not yet been characterized. In this study, refuse and leachate samples with different areas and depths were taken from a large sanitary landfill in Beijing to identify fungal communities in landfills. In high-throughput sequencing of ITS region, 474 operational taxonomic units (OTUs) were obtained from landfill samples with a cutoff level of 3% and a sequencing depth of 19962. The results indicates that Ascomycota, with the average relative abundance of 84.9%, was the predominant phylum in landfill fungal communities. At the genus level, Family Hypocreaceae unclassified (15.7%), Fusarium (9.9%) and Aspergillus (8.3%) were the most abundant fungi found in the landfill and most of them are of saprotrophic lifestyle, which plays a big role in nutrient cycling in ecosystem. Fungi existed both in landfilled refuse and leachate while both the richness and evenness of fungal communities were higher in the former. In addition, fungal communities in landfilled refuse presented geographic variances, which could be partly attributed to physical habitat properties (pH, dissolved organic carbon, volatile solid, NH₄⁺, NO₂⁻ and NO₃⁻), while NO₃⁻ was considered the most significant factor (p<0.05) in shaping fungal community.     

Light-induced variation in environmentally persistent free radicals and the generation of reactive radical species in humic substances

• Light irradiation increased the concentration of free radicals on HS. • The increased spin densities on HS readily returned back to the original value. • The “unstable” free radicals induced the formation of reactive radical species. • Reactive radicals’ concentration correlated strongly with EPFRs’ concentration. Environmentally persistent free radicals (EPFRs) in humic substances play an essential role in soil geochemical processes. Light is known to induce EPFRs formation for dissolved organic matter in aquatic environments; however, the impacts of light irradiation on the variation of EPFRs in soil humic substances remain unclear. In this study, humic acid, fulvic acid, and humin were extracted from peat soil and then in situ irradiated using simulated sunlight. Electron paramagnetic resonance spectroscopy results showed that with the increasing irradiation time, the spin densities and g-factors of humic substances rapidly increased during the initial 20 min and then gradually reached a plateau. After irradiation for 2h, the maximum spin density levels were up to 1.63 × 10¹⁷, 2.06 × 10¹⁷, and 1.77 × 10¹⁷ spins/g for the humic acid, fulvic acid, and humin, respectively. And the superoxide radicals increased to 1.05 × 10¹⁴–1.46 × 10¹⁴ spins/g while the alkyl radicals increased to 0.47 × 10¹⁴–1.76 × 10¹⁴ spins/g. The light-induced EPFRs were relatively unstable and readily returned back to their original state under dark and oxic conditions. Significant positive correlations were observed between the concentrations of EPFRs and reactive radical species (R² = 0.65–0.98, p<0.05), which suggested that the newly produced EPFRs contributed to the formation of reactive radical species. Our findings indicate that under the irradiation humic substances are likely to be more toxic and reactive in soil due to the formation of EPFRs.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Statistical modeling of radiolytic (60Co g) degradation of Ofloxacin,antibiotic: Synergetic effect,kinetic studies & assessment of its degraded metabolites

Linear, interactive and quadratic effects of process parameters were studied. Degradation of Ofloxacin (Ofx) was related with G value of irradiation process. The synergistic effect of H₂O₂ on lower dose of g-irradiation was established. The process follows pseudo first order with dose constant (d = 0.232 kGy^–1). The impact of human activities in the past few decades has paved the way for the release of pollutants due to the improper effluent treatment. Recent studies revealed that, Ofloxacin, an antibiotic as one of the major pollutant affecting surface water and ground water. In this study, the radiolytic potential of Ofloxacin was investigated. The effects of pH, dose and concentration of Ofloxacin were analyzed using One Factor At a Time (OFAT) and the interactive effects between the parameters were studied using Face Centered Central Composite Design. The statistically optimised developed model shows 30% degradation at initial antibiotic concentration of 1mM at pH 3.0 and at 2 kGy dose of gamma ray. The process efficiency was evaluated in terms of G value and its correlation with the concentration of antibiotic was also established. The process of degradation was augmented by the addition of H₂O₂ (1.5 mM). The reaction kinetics for the process was evaluated, the dose rate constant and the rate of degradation for the augmented process was found to be 0.232 kGy^-1 and 0.232 mM/kGy, respectively. The degraded metabolites of the radiolytic degradation of Ofloxacin were analyzed through change in pH, reduction in TOC and GC-MS spectrum.     

Impacts of advanced treatment processes on elimination of antibiotic resistance genes in a municipal wastewater treatment plant

The distributions of ARGs were monitored in a WWTP in Harbin during six months. CASS had the best removal efficacy of ARGs compared to other processes in the WWTP. UV disinfection could effectively control the HGT. AGAC significantly remove ARGs and organics due to its high absorption capacity. Combination of ozone and AGAC significantly improve removal of ARGs and organics. Antibiotic resistance genes (ARGs) pose a serious threat to public health. Wastewater treatment plants (WWTPs) are essential for controlling the release of ARGs into the environment. This study investigated ARG distribution at every step in the treatment process of a municipal WWTP located in Harbin for six consecutive months. Changes in ARG distribution involved in two advanced secondary effluent treatment processes, ozonation and granular activated carbon (GAC) adsorption, were analyzed. Biological treatment resulted in the highest ARG removal (0.76–1.94 log reduction), followed by ultraviolet (UV) disinfection (less than 0.5-log reduction). Primary treatment could not significantly remove ARGs. ARG removal efficiency increased with an increase in the ozone dose below 40 mg/L. However, amorphous GAC (AGAC) adsorption with a hydraulic retention time (HRT) of 1 h showed better removal of ARGs, total organic carbon (TOC), total nitrogen (TN), and total phosphorus (TP) than ozonation at a 60 mg/L dose. UV treatment could efficiently reduce the relative ARG abundance, despite presenting the lowest efficiency for the reduction of absolute ARG abundance compared with GAC and ozone treatments. The combination of ozone and AGAC can significantly improve the removal of ARGs, TOC, TN and TP. These results indicate that a treatment including biological processing, ozonation, and AGAC adsorption is a promising strategy for removing ARGs and refractory organic substances from sewage.     

Stress-related ecophysiology of members of the genus Rhodanobacter isolated from a mixed waste contaminated subsurface

• Rhodanobacter spp. are dominant in acidic, high nitrate and metal contaminated sites. • Dominance of Rhodanobacter is likely due to tolerance to low pH and heavy metals. • High organic content increases stress tolerance capacity. • Longer incubation time is critical for accurate assessment of MIC (various stresses). This work examines the physiologic basis of stress tolerance in bacterial strains of the genus Rhodanobacter that dominate in the acidic and highly metal contaminated near-source subsurface zone of the Oak Ridge Integrated Field Research Challenge (ORIFRC) site. Tolerance of R. denitrificans to levels of different stresses were studied in synthetic groundwater medium and R2A broth. Two strains of R. denitrificans, strains 2APBS1^T and 116-2, tolerate low to circumneutral pH (4–8), high Uranium (1 mmol/L), elevated levels of nitrate (400 mmol/L) and high NaCl (2.5%). A combination of physiologic traits, such as growth at low pH, increased growth in the presence of high organics concentration, and tolerance of high concentrations of nitrate, NaCl and heavy metals is likely responsible for dominance of Rhodanobacter at the ORIFRC site. Furthermore, extended incubation times and use of low carbon media, better approximating site groundwater conditions, are critical for accurate determination of stress responses. This study expands knowledge of the ecophysiology of bacteria from the genus Rhodanobacter and identifies methodological approaches necessary for acquiring accurate tolerance data.     

Locally enhanced electric field treatment (LEEFT) for water disinfection

• Nanowire-assisted LEEFT is applied for water disinfection with low voltages. • LEEFT inactivates bacteria by disrupting cell membrane through electroporation. • Multiple electrodes and device configurations have been developed for LEEFT. • The LEEFT is low-cost, highly efficient, and produces no DBPs. • The LEEFT can potentially be applicable for water disinfection at all scales. Water disinfection is a critical step in water and wastewater treatment. The most widely used chlorination suffers from the formation of carcinogenic disinfection by-products (DBPs) while alternative methods (e.g., UV, O₃, and membrane filtration) are limited by microbial regrowth, no residual disinfectant, and high operation cost. Here, a nanowire-enabled disinfection method, locally enhanced electric field treatment (LEEFT), is introduced with advantages of no chemical addition, no DBP formation, low energy consumption, and efficient microbial inactivation. Attributed to the lightning rod effect, the electric field near the tip area of the nanowires on the electrode is significantly enhanced to inactivate microbes, even though a small external voltage (usually<5 V) is applied. In this review, after emphasizing the significance of water disinfection, the theory of the LEEFT is explained. Subsequently, the recent development of the LEEFT technology on electrode materials and device configurations are summarized. The disinfection performance is analyzed, with respect to the operating parameters, universality against different microorganisms, electrode durability, and energy consumption. The studies on the inactivation mechanisms during the LEEFT are also reviewed. Lastly, the challenges and future research of LEEFT disinfection are discussed.     

Characterization of electrode fouling during electrochemical oxidation of phenolic pollutant

• Electrode fouling is characterized by non-destructive characterization. • Electrode fouling is highly dependent on electrochemical process. • Active chlorine can prevent the formation of polymeric fouling film. Electrode fouling is a problem that commonly occurs during electro-oxidation water purification. This study focused on identifying the fouling behavior of Pt electrode associated with the formation of polymeric layer during electro-oxidation of phenol. The in situ electrochemical measurements and non-destructive observation of the electrode morphology were reported. The results demonstrated that the electrode fouling was highly dependent on thermodynamic process of electrode that was controlled by anode potential. At anode potential lower than 1.0 V vs SHE, the direct electro-oxidation caused the electrode fouling by the formation of polymeric film. The fouling layer decreased the electrochemically active surface area from 8.38 cm² to 1.57 cm², indicated by the formation of polymeric film with thickness of 2.3 mm, increase in mass growing at a rate of 3.26 μg/cm²/min. The degree to which the anode was fouled was independent of anion in the electrolyte. In comparison, at anode potential higher than 2.7 V vs SHE, the anions (e.g., chloride) could exert a major influence to the behavior of electrode fouling. The presence of chloride was shown to mitigate the fouling of electrode significantly through preventing the formation of polymeric film by active chlorine (e.g., Cl• and Cl₂) produced from anodic oxidation of chloride. Since chloride is the most abundant anionic species existing in both natural and engineered water system, this study not only offers a deep insight into the mechanism of electrode fouling, but also suggests strategies for anti-fouling in the presence of chloride in electro-oxidation process.     

Sulfur cycle as an electron mediator between carbon and nitrate in a constructed wetland microcosm

• Fe(III) accepted the most electrons from organics, followed by NO₃^‒, SO₄^2‒, and O₂. • The electrons accepted by SO₄^2‒ could be stored in the solid AVS, FeS₂-S, and S⁰. • The autotrophic denitrification driven by solid S had two-phase characteristics. • A conceptual model involving electron acceptance, storage, and donation was built. • S cycle transferred electrons between organics and NO₃^‒ with an efficiency of 15%. A constructed wetland microcosm was employed to investigate the sulfur cycle-mediated electron transfer between carbon and nitrate. Sulfate accepted electrons from organics at the average rate of 0.84 mol/(m³·d) through sulfate reduction, which accounted for 20.0% of the electron input rate. The remainder of the electrons derived from organics were accepted by dissolved oxygen (2.6%), nitrate (26.8%), and iron(III) (39.9%). The sulfide produced from sulfate reduction was transformed into acid-volatile sulfide, pyrite, and elemental sulfur, which were deposited in the substratum, storing electrons in the microcosm at the average rate of 0.52 mol/(m³·d). In the presence of nitrate, the acid-volatile and elemental sulfur were oxidized to sulfate, donating electrons at the average rate of 0.14 mol/(m³·d) and driving autotrophic denitrification at the average rate of 0.30 g N/(m³·d). The overall electron transfer efficiency of the sulfur cycle for autotrophic denitrification was 15.3%. A mass balance assessment indicated that approximately 50% of the input sulfur was discharged from the microcosm, and the remainder was removed through deposition (49%) and plant uptake (1%). Dominant sulfate-reducing (i.e., Desulfovirga, Desulforhopalus, Desulfatitalea, and Desulfatirhabdium) and sulfur-oxidizing bacteria (i.e., Thiohalobacter, Thiobacillus, Sulfuritalea, and Sulfurisoma), which jointly fulfilled a sustainable sulfur cycle, were identified. These results improved understanding of electron transfers among carbon, nitrogen, and sulfur cycles in constructed wetlands, and are of engineering significance.     

Effect of nitrobenzene on the performance and bacterial community in an expanded granular sludge bed reactor treating high-sulfate organic wastewater

Less than 50 mg/L nitrobenzene brought little effect on anaerobic sulfate reduction. Kinetics of sulfate reduction under different nitrobenzene contents was studied. Increased nitrobenzene contents greatly changed the bacterial community structure. Genus Desulfovibrio played the key role in anaerobic sulfate reduction process. Nitrobenzene (NB) is frequently found in wastewaters containing sulfate and may affect biological sulfate reduction process, but information is limited on the responses of sulfate reduction efficiency and microbial community to the increased NB contents. In this study, a laboratory-scale expanded granular sludge bed reactor was operated continuously to treat high-sulfate organic wastewater with increased NB contents. Results successfully demonstrated that the presence of more than 50 mg/L NB depressed sulfate reduction and such inhibition was partly reversible. Bath experiments showed that the maximum specific desulfuration activity (SDA) decreased from 135.80 mg SO₄^2?/gVSS/d to 30.78 mg SO₄^2?/gVSS/d when the NB contents increased from none to 400 mg/L. High-throughput sequencing showed that NB also greatly affected bacterial community structure. Bacteroidetes dominated in the bioreactor. The abundance of Proteobacteria increased with NB addition while Firmicutes presented an opposite trend. Proteobacteria gradually replaced Firmicutes for the dominance in response to the increase of influent NB concentrations. The genus Desulfovibrio was the dominant sulfate-reducing bacteria (SRB) with absence or presence of NB, but was inhibited under high content of NB. The results provided better understanding for the biological sulfate reduction under NB stress.     

Comparative genotoxicity of water processed by three drinking water treatment plants with different water treatment procedures

• Genotoxicity of substances is unknown in the water after treatment processes. • Genotoxicity decreased by activated carbon treatment but increased by chlorination. • Halogenated hydrocarbons and aromatic compounds contribute to genotoxicity. • Genotoxicity was assessed by umu test; acute and chronic toxicity by ECOSAR. • Inconsistent results confirmed that genotoxicity cannot be assessed by ECOSAR. Advanced water treatment is commonly used to remove micropollutants such as pesticides, endocrine disrupting chemicals, and disinfection byproducts in modern drinking water treatment plants. However, little attention has been paid to the changes in the genotoxicity of substances remaining in the water following the different water treatment processes. In this study, samples were collected from three drinking water treatment plants with different treatment processes. The treated water from each process was analyzed and compared for genotoxicity and the formation of organic compounds. The genotoxicity was evaluated by an umu test, and the acute and chronic toxicity was analyzed through Ecological Structure- Activity Relationship (ECOSAR). The results of the umu test indicated that biological activated carbon reduced the genotoxicity by 38%, 77%, and 46% in the three drinking water treatment plants, respectively, while chlorination increased the genotoxicity. Gas chromatograph-mass spectrometry analysis revealed that halogenated hydrocarbons and aromatic compounds were major contributors to genotoxicity. The results of ECOSAR were not consistent with those of the umu test. Therefore, we conclude that genotoxicity cannot be determined using ECOSAR .     

Enhanced enzymatic removal of anthracene by the mangrove soil-derived fungus, Aspergillus sydowii BPOI

• A. sydowii strain bpo1 exhibited 99.8% anthracene degradation efficiency. • Four unique metabolic products were obtained after anthracene degradation. • Ligninolytic enzymes induction played vital roles in the removal of anthracene. • Laccase played a crucial role in comparison with other enzymes induced. The present study investigated the efficiency of Aspergillus sydowii strain bpo1 (GenBank Accession Number: MK373021) in the removal of anthracene (100 mg/L). Optimal degradation efficiency (98.7%) was observed at neutral pH, temperature (30℃), biomass weight (2 g) and salinity (0.2% w/v) within 72 h. The enzyme analyses revealed 131%, 107%, and 89% induction in laccase, lignin peroxidase, and manganese peroxidase respectively during anthracene degradation. Furthermore, the degradation efficiency (99.8%) and enzyme induction were significantly enhanced with the addition of 100 mg/L of citric acid and glucose to the culture. At varying anthracene concentrations (100–500 mg/L), the degradation rate constants (k₁) peaked with increasing concentration of anthracene while the half-life (t_1/2) decreases with increase in anthracene concentration. Goodness of fit (R² = 0.976 and 0.982) was observed when the experimental data were subjected to Langmuir and Temkin models respectively which affirmed the monolayer and heterogeneous nature exhibited by A. sydwoii cells during degradation. Four distinct metabolites; anthracene-1,8,9 (2H,8aH,9aH)-trione, 2,4a-dihydronaphthalene-1,5-dione, 1,3,3a,7a-tetrahydro-2-benzofuran-4,7-dione and 2-hydroxybenzoic acid was obtained through Gas Chromatography-Mass spectrometry (GC-MS). A. sydowii exhibited promising potentials in the removal of PAHs.     

Presence,dissemination and removal of antibiotic resistant bacteria and antibiotic resistance genes in urban drinking water system: A review

Reviewed the change of ARGs and ARB in full-scale urban drinking water systems. Conventional processes are more promising than BAC process in ARGs removal. Mechanisms of ARGs enrichment and spread in BAC filter and DWDSs are discussed. Raise the need of future research on ARGs and ARB change in building plumbing systems. Antibiotic resistance in aquatic environment has become an important pollution problem worldwide. In recent years, much attention was paid to antibiotic resistance in urban drinking water systems due to its close relationship with the biosafety of drinking water. This review was focused on the mechanisms of antibiotic resistance, as well as the presence, dissemination and removal of antibiotic resistant bacteria (ARB) and antibiotic resistance genes (ARGs) in the urban drinking water system. First, the presence of ARB and ARGs in the drinking water source was discussed. The variation of concentration of ARGs and ARB during coagulation, sedimentation and filtration process were provided subsequently, in which filtration was proved to be a promising technology to remove ARGs. However, biological activated carbon (BAC) process and drinking water distribution systems (DWDSs) could be incubators which promote the antibiotic resistance, due to the enrichment of ARGs and ARB in the biofilms attached to the active carbon and pipe wall. Besides, as for disinfection process, mechanisms of the inactivation of ARB and the promotion of conjugative transfer of ARGs under chlorine, ozone and UV disinfection were described in detail. Here we provide some theoretical support for future researches which aim at antibiotic resistance controlling in drinking water.